Search Documents

By Fiona J. Stevens McFadden, Gregory J. Hardie, Mark P. Taylor, William Uru

"Over 20 million tonnes of installed aluminium smelting capacity exists worldwide, with smelter energy con.sumption in the range 14-17 kWh/kg aluminium. In terms of the reduction cell technology itself, the lowest sustained energy consumption is just below 13DC kWh/kg, or 50% energy efficient.For 15 years Comalco Aluminium Ltd. in Australia has been engaged in developing and testing reduction cells that use a refractory hard cathode, composed of a TiBif carbon composite coating over a carbon cathode. This technology has the potential to reduce energy consumption significantly while simultaneously increasing the life of the cells, which is currently limited by wear rate of the conventional carbon cathodes used throughout the worldIntroductionThe successful development of an aluminium wettable cathode technology affords the opportunity to the cell designer and smelter operator to fundamentally change the physical operating characteristics of the Hall-Heroult process. With this revolutionary capability in hand, published papers and patents have indicated that the technology may be exploited in a wide variety of ways to improve the economic performance of aluminium smelting process. Comalco has been developing refractory hard cathode technology for more than 15 years and has been exploring a number of ways that the technology may be commercially applied in a smelter operation [l]."

Jan 1, 2000

By B M. Guerin

In this paper, some of the constraints to applying bioremediation to the decontamination of polluted soils are introduced. Particularly, attention has been given to those associated with the geology of the polluted site. Areas which require further research have been addressed and indicate that geologists will play a key role, alongside microbial ecologists and engineers, in designing and implementing bioremediation strategies.

Jan 1, 1992

By T. M. Barczak

Longwall tailgates in coal mines are often subject to severe mining induced loading and deformation. Innovative tailgate supports have been developed over the years to provide safe and economical access and a ventilation pathway at the tailgate. The support capacity and yield capabilities of the supports need to be matched to the loading imposed by the surrounding rock mass. The ground response curve can be used to represent the rock mass response to mining and its effect on support systems. The FLAC finite difference code was used to supplement field results by simulating a longwall tailgate and the associated ground response. The ground response curve is developed by modeling tailgate excavations with different internal support pressures and recording the resulting convergence. Ground response curves are developed for two typical longwalls operating in the Pittsburgh seam with weak and strong immediate roof. An additional model is presented in which the effect of weak overburden strata is simulated. The ground response is shown to be significantly affected by the strength of the immediate roof as well as the main roof. The importance of yield capacity of standing support is demonstrated. Gob height and compaction are found to affect the amount of convergence in the tailgate. The potential exists to develop site specific tailgate design curves by combining model results with field observations.

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

By Fernando Humberto Muge

One of the problems that arises in the early stages of the mine planning before the determination of the mining exploitation method is to predict what will be the recoverable ore reserves in tonnage, grade and metal quantity, if the select ion is based upon block grades. The estimation of these recuperation or recoverable functions can act as an important planning tool in what concerns the appraisal of the consequences of ore-waste discrimination of individual blocks in a selective mining operation. Estimation methods of all these functions are discussed together with cross validation tests using the available information concerning a preliminary drilling campaign accomplished during the exploration stage of an iron orebody located in the North of Portugal (Moncorvo Orebody).

Jan 1, 1982

By T. K. Smith

The comments contained in the discussion of the paper concerning the prediction of fracture gradients are of considerable interest, since the subject is of a very controversial and timely nature. It is regrettable and Fairhurst2 contradicts the author's statement in the third paragraph of Other Applications. These references create significant doubt that Eaton's Eq. 1 predicts fracture pressure during the injection of fluid into old wells. 3. No evidence is presented in this paper to support the author's Conclusions 2 and 3. While an empirical coefficient related to back-calculated field data is correlated with depth (Eaton's Fig. 4), there is no reason to suspect that this coefficient might be the Poisson's ratio of the various formations involved. 4. Until the field data supporting the empirical approach proposed by the author are presented and evaluated, the accuracy claimed in Conclusion 5 is without substantiation. References 1. Geertsma, J.: "Problems of Rock Mechanics in Petroleum Production Engineering", Proc., First Intl. Symposium on Rock Mechanics, Lisbon (1966) 585. 2. Haimson, B. and Fairhurst, C.: "Hydraulic Fracturing in Porous-Permeable Materials", I. Pet Tech. (July, 1969) 811-817. that the comments are those of a critic and do not offer an alternative and better method for the prediction of fracture gradients. Nevertheless, a reply is in order.

Jan 1, 1970

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

As opposed to a prescriptive-based design, a performance-based fire-protection system design allows the system planner the flexibility in choosing specific method, materials and design tools to achieve a preset goal. A different approach in fire protection and a powerful addition to existing method, the system has been around for many years, and has gone through numerous improvements. Despite its popularity in the building industry, it has not been introduced to the mining industry yet. As mines get deeper, increases in size and complication, mine fire safety system will also become increasingly challenging, a new and proven system should be able to great potential to eradicate many of the problems that are either unsolvable or cost-prohibitive with the traditional method. With increasing globalization and international exchange with other major mining countries a common language/practice also make the performance-based design method a desirable feature in mine fire safety system. This paper will first define a performance-based system, step-by-step design methods, likely impacts on fire-protection practices and possible challenges in implementing the system in US underground mines.

Jan 1, 2011

Bioleaching of E-Wastes

Sep 13, 2010

By Dara L. Hrytzak-Lieffers

Canada has long since been a place that has led the world in mining development, in a safe, clean, and sustainable manner. This has led to the integration of corporate social responsibility (CSR) philosophy in corporate governance, policy, and programming. The paper will identify the basis of CSR practise in Canada?s mining industry and provide a Canadian example of CSR implementation. Biography Dara Hrytzak-Lieffers is the manager, corporate social responsibility at Cameco Corporation. She oversees corporate CSR initiatives including the Sustainable Development report and public engagement programs. Dara received her BA in International Studies from the University of Saskatchewan and an MA in International Conflict Analysis from the Brussels School of International Studies. She is a recent graduate of the World Nuclear University summer institute.

May 1, 2011

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By Akul Joshi, Ming C. Leu, Robert Guttenberg, Susan L. Murray

The aerospace and automotive industries are facing a significant risk for cumulative trauma disorders from high-repetition, long-duration tasks. Additional risk factors such as shocks, vibrations and sustained uncomfortable postures oftentimes contribute to musculoskeletal, neurological injuries associated with the hand-arm system. The power tools used for the operation reduce the comfort and working efficiency of the operators, thus lowering their health and safety and the quality of operation. This paper investigates the fastening operation on the assembly line of a major aerospace company for quantifying hand-arm vibrations with the objective of developing a dynamic model of the hand-arm system. The model will be used to ascertain the effect of the various risk factors on the quality of the operation. Experiment Setup A system of three tri-axial accelerometers is used to collect vibrations entering the hand-arm system and their positioning follows the ISO-5349 standard. Reaction force during the operation is measured using a force sensor. The posture of the hand-arm system is measured using two goniometers and one torsiometer. The pilot study conducted has two subjects and one pistol-grip power tool. The experiment setup and positions of various sensors is depicted in Figure 1. [ ] Analysis Method The analysis consists of transmissibility of vibrations and frequency weighted acceleration based on the recommendations of the ISO-5349 standard [1,2]. The transmissibility [3] was deduced in frequency domain after measuring data in time domain from the

Jan 6, 2006

By K. Pathak

Loaders and dump trucks are the most commonly used surface-mining equipment. Negligence of the safety-engineering aspects of dump trucks may result in serious accidents in a mine. A reduction in the risk of an accident due to the deployment of trucks can he achieved by engineering analysis, risks assessment, improved safety features, active safety devices, condition-based maintenance, in-built protection systems, etc. This paper presents some cases of accidents in Indian surface coal mines and advocates a systems approach to safety.

Jan 1, 1999

By B. Unver

Effective strata control is a prerequisite for maintaining an efficient mining operation. If the strata in the vicinity of an opening are not controlled effectively, it is impossible to perform a safe, efficient and economical operation. In this paper, the reasons and outcome of instability problems observed in roadways opened in clay and marl at the Bolu Colliery of Yeni Çeltek Establishment are investigated. Roadways under examination were located in a syncline causing high residual tectonic stresses. Factors affecting the instability have been studied thoroughly by examining geology and tectonics of the area, establishing convergence measuring stations to understand in situ behaviour of supports and laboratory tests to determine engineering properties of samples taken from nearby convergence measurement stations. As a conclusion, a new production strategy and a new support system are recommended to maintain stability.

Jan 1, 1999

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By H. Sevim

Placement of coal combustion byproducts into abandoned sections of underground coal mines for the purpose of subsidence mitigation has been investigated in Illinois. Several handling and transportation systems have been examined. Prototype pneumatic and hydraulic placement systems have been developed and demonstrated. The demonstration site, Peabody No. 10 mine in Pawnee Illinois, is selected as a case study. It is found that, for a project of 5 years, transporting 150,000 tons of byproduct annually from a power plant located 32 km (20 miles) to the mine would cost $1.80 per ton and placement into underground would cost $3.07 per ton.

Jan 1, 1998

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

Jan 1, 1968

By M Grigorescu, J H. Hodgkinson

The expansive, open cut iron-ore mines in Western Australia typically experience few days of rain per annum, often amounting to less than 250 mm. Unlike mines where rainfall is frequent, they may be less prepared for extreme rainfall events. Such events can cause erosion, flooding and sedimentation, drainage alteration, spoil and stock heaps wetting and effect slope stability. Such impacts may threaten personnel safety, infrastructure, and production. The CRATER (‘Climate Related Adaptation from Terrain Evaluation Results’) framework collates and interprets a mine’s pre-existing data and semi-quantitative information to assess vulnerability to, and ultimately plan to avoid or minimise, flood-related hazard to infrastructure, people, downtime, environment and revenue. Outputs assist decision makers to design investment strategies for minimising mining operations’ vulnerability to climate. Previously developed for smaller, wetter mines in Queensland’s coal region, the outputs provide a hot-spot map, fault tree analysis and an assessment of the mine’s capacity to adapt. The multicriteria evaluation (MCE) within a geographic information system (GIS), equally suits iron-ore mines’ siteconditions (elevation, slope, drainage, soil and vegetation) to identify critical inundation areas. Hotspot results provide target zones for in-depth fault-tree analysis that, in turn, present a range of sitespecific adaptation options. Rainfall-intensity and the number of rain days since the 1970s have increased over central and eastern parts of the Pilbara Region. While tropical cyclones may become less frequent, they are projected to increase in intensity. Although some parts of the Hamersley Ranges receive more than 500 mm per annum, rainfall in the Pilbara is generally very low. Therefore, experience of the impacts of extreme rainfall events in the constantly changing topography of Western Australia’s iron ore region may be sparse. Minimising potential effects can be proactively assisted using CRATER.

Nov 8, 2021