Search Documents

Jan 1, 1966

Preheating Feature of Leyner Oil Furnace for Heating Drill Steel The No. 3 Leyner oil-burning furnace, used for heating drill steel, is now made with a preheating chamber. By this addition it is claimed that the heating capacity and, effeciency of the furnace are increased about 50 per cent. This preheater is a section which fits between the body and cover of the furnace of the old design. It may be attached to an old furnace by simply changing a few bolts. Referring to the illustration, it will be seen that the lower chamber is used for the final heating and the upper one for preheating. The type of burner now furnished with this furnace is suitable for either high- or low-pressure air. It hats merely to be throttled for high pressures and when this is done, it, is as efficient as burners designed especially for high pressures and eliminates the noise common to such burners. This furnace burns petroleum or any of its oils, such a, gasoline, kerosene, distillate, etc. Oil heating has many advantages. The steel cannot be injured by absorbing injurious elements such as sulphur, phosphorus or other impurities which :ire present in nearly all coals, nor from unequal heating since the flame imparts a uniform temperature; further, o lie steel is in full view of the operator at all times.

Jan 3, 1916

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of varibles, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

Bacterial leaching represents an unusual problem in biochemical engineering, because the substrate for bacterial growth is not supplied directly, but is a product of another reaction, the leaching of mineral particles. Leaching arises from the bacterial oxidation of ferrous ions to ferric ions, which in turn oxidize the mineral. For the bacterial dissolution of pyrite, these reactions are: [ ] (Y represents a stoichiometric yield factor, and N represents the amount of bacteria.) Equations [1] and [2] represent a cyclic auto-catalytic system since more ferric ions are added to the system with an increase in the extent of leaching.

Jan 1, 2000

By A Gerson, S Miller, R Smart, J Thomas

Environmental Geochemistry International (EGi) and the Ian Wark Research Institute (IWRI) collaborated in a three-year Australian Minerals Industry Research Association (AMIRA) research project (Project Number P387A) focussed on the prediction and kinetic control of acid mine drainage. As part of this project, single addition, and sequential net acid generation (NAG) testing was carried out on sulfide mineral samples. The test samples comprised a range of synthetic waste materials prepared using a quartz bulk and controlled quantities of the commonly occurring sulfide minerals; pyrite (FeS2), pyrrhotite (Fe7S8), arsenopyrite (AsFeS), chalcopyrite (CuFeS2), chalcocite (Cu2S), covellite (CuS), bornite (Cu5FeS4), galena (PbS) and sphalerite (ZnS). NAG test results clearly show that there are significant differences between the acid forming potential of sulfide minerals. The NAG test results for each mineral were compared with theoretical acidity values (NAPP*). The NAPP* calculation was based on stoichiometric oxidation reactions assumed for each of the sulfide minerals. Sequential NAG values for pyrite corresponds closely to predicted NAPP* values, confirming the assumption that pyrite oxidation occurs according to the stoichiometry assumed. For the pyrite sample with 5 wt per cent S, two NAG stages were sufficient for all of the sulfur to be released to solution. Since sulfides in waste materials will generally be dominated by pyrite, results also confirm the validity of including NAG testing for ARD evaluation of most waste rock. NAG testing confirms that of the sulfide minerals examined, only pyrite, pyrrhotite, arsenopyrite and chalcopyrite are acid producing, ie able to produce leachate with a pH less than 4.5. In the case of sphalerite, galena, bornite, chalcocite and covellite the pH of the final NAG solution was greater than 4.5. The significant differences between the acid forming potential of different sulfide minerals could lead to overestimation of acid producing potentials based on NAPP values calculated from total per cent S alone, ie assuming all S is present as pyrite. The oxidation of galena during the NAG test resulted in the consumption of acid. The examination of the galena surface by X-ray photoelectron spectroscopy (XPS) after oxidation in peroxide solution indicated the presence of polysulfide. The reaction of sulfide to polysulfide is acid consuming, thus explaining the net acid consuming behaviour of galena in the NAG test. This reaction pathway may provide a possible explanation for the lower than expected acid production observed for some of the other sulfide minerals examined.

Jan 1, 2003

By J. T. Bartlett

Life-of-mine process simulation is an interdisciplinary effort and a useful means of thoroughly evaluating mining and minerals projects. Communication between geologists, mine planners, miners, metallurgists, and managers not only benefits each discipline but facilitates design of an efficient operation and allows for accurate forecasting of productions and cash flow. By focusing on the key areas: geology; mine design; waste dumps; stockpiles; metallurgy; weather data; tailings disposal; using contours, block models, mine plans, process flowsheets, design criteria, operating and control strategies, maintenance schedules, and operating costs to perform detailed daily simulation from start-up to shut-down; a comprehensive understanding for all disciplines is achieved. Construction of a METSIM model that includes all test work and project data from drill holes through net present value calculations brings the pieces together to achieve optimum process design, minimize operating problems and eliminate the term ?black box? from project meetings and discussions.

Feb 27, 2013

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

By P. Amelunxen

This paper presents the authors? personal experiences in the design and operation of moly separation circuits in copper-moly concentrators. Topics discussed include column cells versus mechanical cells; use of nitrogen; use of CO2 and sulfuric acid for pH modification; and general equipment selection and sizing. A benchmarking of main operating parameters for industrial plants is presented. Upgrading curves for commercial column and mechanical cleaning circuits are also presented, showing that with average flotation kinetics and rougher concentrate grades, technical grade concentrates can be easily achieved with five column cells operating in counter-current configuration.

Jan 1, 2009

By D. Mkhwanazi

The purpose of the project was to optimize load haul dump (LHD) machinery use as they were spending too much time doing what they should not be doing. During the investigation, the author found that the machine's actual availability was 86% and the utilization ranged between 30% and 42%. This shows that the availability of the machine has met its target. Therefore the main problem was with the LHD utilization and that is what the project focuses on. To satisfy the objectives, the author firstly studied the existing mining data like the key performance indicators (KPIs) in order to analyse the machine's availability and utilization; this is what gave direction to the problem. Secondly the author did a literature review on mines with similar problems. This gave the author ideas on what to look at in approaching such a situation. Thirdly, the author gathered information on what the LHDs are doing on a daily basis by doing a time study. This gave the author an idea of how long it took the LHDs to complete a specific task. The author also interviewed operators and their supervisors in order to find the best practice work. This helped in identifying the problem areas when comparing the best practice work with what the LHDs are actually doing. According to the project results, it was found that the LHDs are underutilized due to shortage of drivers and the long distances the LHDs have to travel for material loading and refuelling. The author recommended that the machine utilization should be improved by training more operators in order to eliminate the 'no operator' downtime; the cost arrangement of this recommendation is included in the report. The author also recommended that the travelling time should be reduced by using tractors instead of LHDs when long distances need to be travelled for material loading. Another recommendation for reducing travelling time was to bring the mobile fuel tank closer to a section; the cost arrangement for this recommendation is also included in the report. Keywords Optimizing, LHD utilization, LHD availability, key performance indicators (KPI), shortage of drivers, long distances, mobile fuel tanks.

Jan 1, 2011

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

By M. J. Sapko

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations) even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of current and future pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners? Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic, and safe mine sealing technique that can enable mines seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble in combination with a conventional mine seal so that the pressure resulting from a gas explosion is reflected, absorbed, and attenuated, so the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a ?Passive Mine Blast Attenuator? (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals. DISCLAIMER: This information is distributed solely for the purpose of pre-dissemination peer review under applicable information quality guidelines. It has not been formally disseminated by the National Institute for Occupational Safety and Health (NIOSH). It does not represent and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By P. J. Rider

Diamond Value Management?s objective is to achieve $/ton revenue improvement across De Beers group mines. The respective %improvement contributions are measured against targets set by each of the operations. Degree of target achievement is measured via a maturity model at each operation. DVM comprises seven elements. It spans several value chain facets and various collaborative projects are conducted under its umbrella. New technologies in De Beers are also evaluated from a DVM perspective.

Jan 1, 2003

Material scheduling, sequencing planning and execution are the core tactical mine plan for achieving production targets that maximize the objective function of any mine production entity. This objective function is constrained by several exogenous and endogenous constraints including geological, operating, technological, marketing, financial, political, social and local field constraints. Linear and dynamic programming techniques have been used to formulate algorithms to solve the problems associated with scheduling and sequencing operations. These algorithms possess the mathematical rigor for dealing with the fundamental problems but they fail to provide adequate answers to random and dynamic process problems. Materials scheduling and sequencing are carried out within the bounds of random and dynamic fields. The functional relations between the output and dependent variables are random, and thus, current algorithms are limited in their abilities to address the problems arising from these random field processes. In this study a production simulator is developed to capture the random field process associated with materials scheduling and sequencing in an open pit environment. The algorithm incorporates a geometric pit evolution model, using solid geometry of an ellipsoidal frustum to capture material displacement dynamics. Taylor series expansion about the dimensions of the initial frustum is used to provide numerical solutions to the resulting partial differential equations governing the pushback dynamics. A production simulator, derived from the stochastic and dynamic models, is developed, validated and used to simulate the changes in the pit volume resulting from periodic incremental pushbacks and the random field process. The hybrid stochastic-optimization algorithm provides a powerful tool for addressing the random field and dynamic process problems. Combined with a hybrid stochastic-optimization dispatch system, tactical production planning and execution will be efficient and economic for achieving desired.

May 1, 2004

By Darold Woodward, Stefan Haydn, Petr Pospisil

Most fatalities in tunnel fires are caused by the spread of toxic smoke. Controlling the spread of smoke is crucial to provide a survivable environment for emergency egress. A properly designed and tuned feedback control loop is required to achieve a target flow that is slow enough to allow pedestrians to escape under different boundary conditions. Feedback control loops are also helpful in optimizing energy consumption under moving traffic conditions. A reliable feedback flow control system requires sophisticated engineering knowhow and experience, careful selection of instruments and controlled variables, and thoughtful implementation from design through field testing and commissioning.

Dec 1, 2022

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.

A simulation and animation model was constructed for the Stockton Coal Mine. This mine is located in the north western area of the South Island of New Zealand. This model was used to study the optimum size of the stockpile areas whilst achieving the correct product coal qualities. The model evaluated the impact on stockpile size and product coal qualities for both bulk and selective mining. The effect of modifying the amount of known clean coal quality was also investigated. The software used was GPSS/H« for the simulation and Proof Professional« for the animation. From the study, it was recommended to incorporate selective mining in future studies. The shipping plan needed to be modified for a better correlation between coal production levels, in situ coal resources and wash plant capacity.

Dec 6, 2010

By Daniel J. Rider

In 1980 the Niagara Frontier Transportation Authority contracted for three miles of cut and cover box structure and station construction in Main Street, Buffalo, New York. Project depths ranged from 30 feet to 60 feet below street grade. Soils, Figure No. 1, consisted of loose to very compact sands and gravels. Ground water level was generally 20 feet below grade. Specifications required a soldier pile and timber lagging support system with external dewatering. Soldier piles were to be installed in prebored holes with bentonite slurry and lean concrete backfill. Conventional pile driving was not allowed due to concerns over excessive noise and vibrations and its effect on nearby historic structures and the surrounding population

Jan 1, 1987

By Verónica Rueda

El proceso de explotación de la Minera Rayrock se inició hace seis años a tajo abierto y ahora comprende las etapas de extracción del mineral, chancado, aglomeración, lixiviación, extracción por solventes y electro-obtención. En ese sentido, el presente trabajo describe el avance del proceso de extracción en el proyecto minero Ivan, perteneciente al yacimiento de la minera Rayrock a través de las técnicas de lixiviación de minerales oxidados y sulfurados de cobre y del manejo innovador en las operaciones de extracción por solventes y electro-obtención.

Sep 13, 2001

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

The mining industry continues to faces significant challenges due to increasing resource constraints (quality of ore bodies, water, energy, human resources) and increasing license to operate requirements (safety, health, environment, location) from society, employees and shareholders. Technology advancements and hence research are necessary to ensure that the industry remains viable in this changing environment. Collaborative research is an important part of a company's research portfolio and offers the opportunity for the industry to work on generic issues that it is facing. Obvious benefits include the reduced cost to individual companies by sharing the costs, the opportunity to leverage government funding and the opportunity to conduct longer term projects resulting in skills development (PhD and MSc). Limitations of collaborative research include the reduced focus on company specific issues and the loss of competitive advantage from owning the outcomes of the research. The challenge for researchers and research managers is for them to demonstrate the value derived from longer term, pre-competitive collaborative research. The competitive advantage is not necessarily derived only from the outcomes of the research but rather from the company's ability to direct the research, translate the generic research outcomes to address company specific issues and to implement improvements at its operations. Implementation remains the greatest challenge. In this paper, case studies of selected collaborative research projects are presented to demonstrate key success factors required for implementation of research outcomes. This is an ABSTRACT ONLY. A full-length paper was not prepared for this presentation.

Sep 13, 2010