Search Documents

By Raymond D. Sloan

Retaining third place in crude-oil production among the nation's oil-producing states, Oklahoma's output in 1942 totaled 137,792,000 bbl., a decline of 9.4 per cent from the previous year's total of 152,117,000 bbl. Production declined from an average of 403,000 bbl. daily in January 1942 to an average of 355,000 bbl. during December, a reduction of 48,000 bbl. daily (11.9 per cent) during the year. At the end of 1942 it would appear inevitable that the downward trend in production will continue in 1953 unless halted in the immediate future by greater than normal discoveries and development. To Jan. I, 1943, Oklahoma has produced 5,067,013,000 bbl. oil crude oil. Development and Exploration Development dropped abruptly in 1942, reflecting the lack of any sizable discoveries and the effect of the provisions of Federal Well Spacing Order M-68, which became effective in December 1941. In all, 1210 wells were drilled in 1942. This represents a decrease of 42.7 per cent from the 1941 total of 2110. Of the total wells completed, 553 (45.7 per cent) were oil wells with an average initial production of 443 bbl.; 102 (8.4 per cent) were gas wells with an average initial of 3,359,000 cu. ft.; and 555 (45.9 per cent) were dry. Although the number of completions declined sharply, the total of 320 wildcats completed (26.4 per cent of all wells) repre-sents a decrease of only 2.7 per cent from the previous year's figure of 329. Of the wildcats drilled, 44 (13.8 per cent) were oil wells, 13 (4.0 per cent) were gas wells, and 263 (82.2 per cent) were recorded as failures. Reconditioning of wells throughout the state resulted in a total recompletion of 355 wells. Of these, 234 were oil wells with a combined initial production of 96,808 bbl., 32 were gas wells with a total initial of 381,488,000 cu. ft., and 89 were abandoned. None of the 26 pools found in 1942 has developed into a major discovery. The Pauls Valley pool, Garvin County, is the most outstanding. Since its discovery in April, 14 wells with an average initial of 1898 bbl. have produced 803,000 bbl. of 42' gravity oil from the Bromide zone. Development in this pool is believed to be almost completed. Other of the more important discoveries are the East Watchorn pool, Pawnee County; Guthrie Townsite and West Navina, Logan County; Brooksville and Macomb, Pottawatomie County, and the Liberty and Northeast Lucien discoveries in Noble county. The East Watchorn pool, at the close of the year, had 14 completed oil wells with an average initial of 989 bbl. from the Wilcox sand at 3930 it.; Guthrie Townsite, one well with an initial of 840 bbl. from dolomite at 5600 It.; West Navina, six wells with an average initial of 284 bbl. in the Lay ton sand at 5050 ft., Brooksville, eight wells in the Hunton at 4800 ft. with an average initial 01 355 bbl.; Macomb, one well with an initial of 160 bbl. in the IIunton at 4700 ft.; the Liberty pool, one well with an initial of 1268 bbl. in the second Wilcox at 4500 ft., and two wells in the Tonkawa sand at 2500 ft., with an average initial of 230 bbl. In the Northeast Lucien pool, four wells were completed in the Wilcox at 5380 ft. for an average initial of 1164 bbl., and one well was completed in the Viola lime at 5255 ft. for an initial of 55 barrels.

Jan 1, 1943

University of Alabama University, Alabama Mining and Metallurgical Society WILLIAM R. HIGGS, President ROBERT E. MEAD, Secretary J. R. CUDWORTH, Faculty Sponsor MILTON H. FIBS, Counselor University of Arizona Tucson, Arizona Miners' Society LEE BLESSING, President R. W. CORY, Secretary E. P. MATHEWSON, Faculty Sponsor B. R. HATCHER, Counselor University of California at Los Angeles Los Angeles, California Student Chapter, A.I.M.E. ARCHER WARNE, President ROBERT JOHNSTON, Secretary E. K. SOPER, Faculty Sponsor EMILE HUGUENIN, Counselor Colorado School of Mines Golden, Colorado Student Chapter, A.I.M.E. J. Ross REED, President ANDREW PERRY, JR., Secretary J. BURNS READ, Faculty Sponsor A. W. NEWBERRY, Counselor

Jan 1, 1936

By W. L. Cooley

A significantly different method of evaluating mine ground system safety is investigated. The method measures touch and step potentials around ground beds and grounded equipment resulting from a series of extremely small simulated faults. The values are then scaled for a full-scale fault. The method should be particularly useful for large ground beds and under conditions where the ground bed cannot be isolated from the rest of the ground system in order to make traditional ground bed resistance measurements. Instrumentation for making the alternative measurements is evaluated under rigorous field conditions. A step-by-step procedure is proposed for evaluating a surface mine ground system. This procedure was subject to several field tests at eastern metal/non-metal mines. The final evaluation procedure is written as a stand-alone document for use by MSHA inspectors and mine operating personnel, and is included as an appendix to the report. The authors conclude that the procedure is effective in evaluating ground system safety and recommend that it be further evaluated in the field.

Jan 1, 1985

By Albert Hofstra, Joel Leventhal

The gray, dark gray and black colors of the sediments and the presence of pyrite in the Carlin, Jerritt Canyon, Horse Canyon, Betze, and Gold Acres sediment-hosted disseminated gold (SHDG) deposits indicate that these rocks are not oxidized with respect to carbon and iron sulfide. Both ore and non-ore host rocks generally are dark colored. Analyses for noncarbonate carbon (usually called organic carbon) in samples from SHDG deposits and related unmineralized rocks indicate that these rocks contain from a few tenths to a few percent carbon. We use the term noncarbonate carbon because, strictly speaking, organic carbon denotes carbon that is bound to hydrogen. However, the carbon present in SHDG deposits and related rocks has very little hydrogen chemically bound to it. Rocks with less than 2% organic carbon are usually gray in color. The dark colors in our samples are due to the relatively high temperatures that these rocks have experienced relative to organic matter maturation. We confirm the results of Nelson et al. (1982) that previous reports (for example, Radtke and Scheiner, 1970) were incorrect in reporting significant amounts of humic acids, extractable hydrocarbons (bitumen) or "carbonaceous" material. We believe these reports had problems with contamination or misdirected emphasis. Our samples consisted of unweathered rocks, collected mainly from mine cuts (benches, trenches, cores) and put into glass containers or wrapped in aluminum foil to avoid contamination. Only a few samples were collected from natural outcrops. We were careful to avoid samples in proximity to blast holes that were packed with ammonium nitrate and diesel fuel ("ANFO"). Contamination by ANFO may explain some of the previous reports of hydrocarbons, pyrobitumens, humic acids and anomalous nitrogen. When we were collecting samples, it was apparent that in addition to lithologic and color differences, the surface appearance of the rocks was distinguishable: "preg robbing" material that had a sooty surface; "graphitic" rock with a shiny surface; and more ordinary rocks that had a flat gray or black appearance. [Preg robbing is a term for ores that adsorb gold from the milling circuit; the graphitic material had not been x-rayed to actually identify graphite.] We hoped that laboratory study of these samples would show some fundamental differences that we could relate to ore genesis. Even though these sample types appeared different in the field, we could not distinguish any differences in thermal maturity (see below). Normal petroleum/organic geochemical laboratory procedures (solvent extraction, Rock-eval, pyrolysis-gas chromatography) failed to yield much information because the carbon was over-mature relative to oil and gas generation. Rock-eval results show less than 20 (± 20) mg of pyrolizable hydrocarbons per gram organic carbon (and an indeterminate Tmax) indicating that the organic matter in these deposits is burned-out relative to petroleum generation [with an H/C (atomic) ratio of less than 0.41. Because of the non-definitive results from standard organic geochemical methods, x-ray diffraction (XRD) and Raman spectroscopy were used to characterize the carbon. Prior to XRD, samples were treated with HCl and HF acids (1) to remove quartz that has a peak near 26° [20] at the position of the 002 peak of graphite and (2) to concentrate the carbon to a level detectable by XRD. The residue was put on a colodion mount and analyzed by XRD. The XRD analyses yielded a broad peak at 26° [20]. The shape of this peak indicates that the carbon is more thermally mature than anthracite rank coal but less mature than crystallized graphite. Based on XRD results from the literature (Landis, 1971) that are calibrated to metamorphic facies, results from our samples correspond to pumpellyite-actinolite to lowermost greenschist facies conditions, probably

Jan 1, 1990

By N. Kumar Kittusamy

Operators of construction equipment perform various duties at work that expose them to a variety of risk factors that may lead to health problems. A few of the health hazards among operators of construction equipment are: (a) whole-body vibration, (b) awkward postural requirements (including static sitting), (c) dust, (d) noise, (e) temperature extremes, and (f) shift work. It has been suggested that operating engineers (OEs) are exposed to two important risk factors for the development of musculoskeletal disorders: whole-body vibration and non-neutral body postures. Method: This review evaluates selected papers that have studied exposure to whole-body vibration and awkward posture among operators of mobile equipment. There have been only few studies that have specifically examined exposure of these risk factors among operators of construction equipment. Thus other studies from related industry and equipment were reviewed as applicable. Conclusion: In order to better understand whole-body vibration and postural stress among OEs, it is recommended that future studies are needed in evaluating these risk factors among OEs.

Jan 1, 2004

By Vahid Tajdar

The behavior similarity between pile and cone penetration test, has guided the researchers to use the CPT results in prediction of piles bearing capacity. In this article, artificial neural networks have been used to study about relation between cone tip and sleeve friction strength obtained from cone penetration test and ultimate pile bearing capacity, obtained from static pile load test. Artificial neural networks "ANNS" is a form of artificial intelligence. ANN tries to dramatize the human nerves & brain system biology structure in self-structure. In this article, the results of relevant studies about the prediction of ultimate pile bearing capacity in especial area of soils are presented by use of back - propagation neural networks. The results of static pile load test up to failure on 63 piles with closed end and CPT test results in the place of construction these piles use in order to confirm and creation ANN model. Comparing predicted ultimate pile bearing capacity by utilizing ANN with the numbers which are predicted by 5 common traditional methods shows that using of artificial neural networks is a suitable method for predicted ultimate pile bearing capacity in identified area of texture of soil moreover it has a better operation in comparison with common traditional methods.

Jan 1, 2006

By Rick Honaker

Rare earth elements (REEs) contained in coal and associated mineral matter exist in several forms including micro-dispersed minerals, ion adsorption onto clay surfaces, and chemically bound. Tests found that REEs can be effectively recovered from certain components of three coal sources by leaching under mild conditions followed by solvent extraction. A range of pH values were evaluated at solution temperatures of 25 and 75 °C. When using 1.2 M of sulfuric acid, nearly 85% recovery of the REEs was extracted from the middlings material collected from an operating plant. Acid leaching of a second middling source from another plant resulted in 60% of the total REEs being recovered under the same leaching conditions. Solvent extraction treatment of the leachate produced from six different coal sources resulted in products containing up to 50% total REEs from feedstocks starting with around 300 ppm.

By Irina Dobretsova, Anna Sukhanova, Anatoly Kondratenko, Svetlana Babaeva, Sergey Andreev

"With the acceptance of an application and a signed contract for prospecting deep-sea sulfides (2012) between the Russian Federation and the ISA, at present it is particularly important to assess the quality of oceanic sulfide minerals and to reliably estimate their resources.Some procedures of geochemical classification (chemical analyses, mineral composition of SMS) and calculations (density of ore, density of the mineral part of the ore, porosity and moisture contents) were used for estimation of mineral resources potential.The key characteristics for estimating the predicted resources of hydrothermal ore fields are the metal contents and the density of wet and dry sulfide ores. However, in the future it is impossible to provide an estimate of the predicted resources without taking into account the following important factors:- the quantitative ratio of main sulfide minerals;- proportion of non-metallic components (opal, quartz, talc);- the replacement of primary minerals by copper sulfides;- texture-structural features of sulfide ores.The offered mineral classification of the SMS is based on the prevalence of minerals in the ores and partly on their composition. The main ore-forming minerals of SMS are pyrite, chalcopyrite and sphalerite. Sulfide mineralization is accompanied by the presence of nonmetallic minerals, where quartz and opal prevail, and where we also meet aragonite, talcochlorite and anhydrite."

Jan 1, 2017

By Edward L. McHugh

The Thousand Lakes Wilderness has no known economically significant mineral resources. However, the geologic setting of the Wilderness indicates a potential for the discovery of geothermal resources. INTRODUCTION The Thousand Lakes Wilderness occupies 16,335 acres (6,611 ha) in eastern Shasta County, California. A mineral resource study of the area was authorized by the Wilderness Act of 1964 (Public Law 88-577). Mining records and published information were examined, and field investigations conducted in 1979. The Wilderness is about 50 miles (80 km) east of Redding and 12 miles (19 km) south of Burney, California. It lies in the Cascade Range of California. Relief is more than 3,000 feet (910 m); elevation is greatest at the summit of Crater Peak, 8,677 feet (2,645 m).

Jan 1, 1982

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By Robert Hopler

The literature of explosives and blasting consists of a great variety of printed materials. These materials include technical papers, books, and articles by individuals and organizations; manufacturer’s product catalogs and brochures; handbooks offering guidance for the field blaster; complete encyclopedias on the subjects, and short entries in general-interest encyclopedias; government publications; proceedings of organizations devoted to the subjects; magazines specific to the subjects; articles in general circulation magazines; and other miscellaneous sources. In short, there is a multitude of literature on the subject, some well indexed for retrieval, but most not. This presentation will be a broad-brush look at some of the most important or interesting literature on the subject, since in no way can all the various references be mentioned, much less covered in depth. To illustrate the presentation, interesting materials from the author’s collection will be shown.

Jan 1, 2000

By Jacques J. Eksteen

Metallurgical accounting around toll treatment smelters pose a number of challenges. This paper reviews the requirements for good sampling practice, and how conflicting requirements for good furnace operation and design often makes reliable closure of the metallurgical balance tenuous at best. Typical physical causes of variance and bias will be identified. The propagation of error (in the form of variance) will be discussed for a copper smelter.

Jan 1, 2006

By M. A. W. Bryson

It is well documented that a significant amount of the new PGM (Platinum Group Minerals) production that is coming on stream now, and over the next few years, is to come from the UG-2 reef. Clearly the reservations, or perhaps the perceived reservations, attached to the processing of this ore are no longer there. What were the metallurgical issues that delayed the exploitation of the PGM values from this reef? Traditional furnaces treating Merensky concentrates were not able to accept the concentrate produced from a UG-2 plant due to the relatively high chromite content of this product. The chromite reports to an insoluble spinel phase that accretes in the furnace, resulting in the necessity to shutdown and dig the furnace out periodically. This was clearly not an attractive economic option, so producers stayed away from it in the early days. The Merensky ore had all higher base metal credits anyway, and you needed them to get a matte fall, so there was no driving force to look seriously at the UG-2 reef. Platinum demand at this time could be easily met from the Merensky ore, so the motivation to tackle more complex ores was not there. The low price of PGMs meant that these operations were not particularly profitable and there was little effort directed at improving the operations. Concentrators were generally not run very efficiently and the emphasis was on cost reduction through increasing milling rates.

Jan 1, 2004

By Karim El-Ouassiti, Marc Minville, Stéphane Chabot, Claude Bazin, Valérie Ouellet

"Alumina is the main source of aluminium and it is extracted almost exclusively from bauxite ores found in the Southern hemisphere. Clays are abundant minerals that contain from 15 to 40% w/w of alumina from which it can be extracted by various processes. This paper reviews the processes used for the extraction of alumina from clays and discusses results obtained with a clay sample from the Murdochville area in the Quebec Province. The application of a conventional process to this clay did not yield an acceptable recovery although smelter grade alumina was produced. A modification to the process allows increasing alumina recovery from 85% to more than 92%. The application of the improved flow sheet to other alumina carriers failed to yield comparable recovery, showing that an optimum processing path for the recovery of alumina should be found for individual clay materials.INTRODUCTIONMost of the aluminium smelters are fed with alumina extracted from bauxite found in the Southern hemisphere. Bauxite is processed by the Bayer process that uses a caustic leach of the ore. In the middle of the century, the US Bureau of mines, motivated by the fear of an alumina delivery disruption, conducted several research projects aiming at producing alumina from non bauxitic ores. These projects led to the development of various acid leaching processes (Habashi, 1993). The sulphuric and hydrochloric acid leaching processes were brought to pilot plant evaluation (Bengtson, 1979), while nitric and other leach liquors were tested in the laboratory (Phillips and Wills, 1982; Habashi, 1983). Although clays are abundant and inexpensive minerals, the studied processes remained uncompetitive with the alumina extraction from bauxite (Hudson, 1987 page 42; Peters et al., 1962) for which reserves are estimated to support alumina production for the next 50 years (Oye et al., 1999). On the other hand, the local extraction of alumina from clays could significantly reduce the transportation costs of alumina to smelters and provide an alternative source of alumina supply from the Southern hemisphere countries. Also, the extraction of secondary products for some types of clay (Nasyrov et al., 1999) containing significant amounts of potassium and sodium could provide an additional return that may improve the economics of alumina production from clays."

Jan 1, 2005

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation, which often requires that the primary ventilation system is upgraded with additional shafts and surface fans. The use of booster fans underground is a potentially practical alternative. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room and pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By R. Luhrman, E. Christ, B. Gores, S. Fischer, E. Johanning

North American railroad locomotive operators (engineers and conductors) are exposed to multi-axis vibration and shocks (1, 2). A recent epidemiological survey showed a prevalence of serious type of neck and lower back disorders nearly double that of a control group (3). Ergonomic working conditions are important co-factors in a vibration and shock exposure risk assessment (4, 5). The goal of this study is to illustrate typical work stations (cabs and seats) in US/Canadian type locomotives and assess shock related exposure risk by calculations of the new proposed shock risk indicators according to the new ISO 2631-5 (2004) (6). Methods Locomotive cab and seat inspections were conducted and operators’ activities were assessed by a trained observer. Field measurements (n=50) were obtained during normal revue service following generally accepted guidelines (ISO 2631 (1)). A sub-sample of n=20 locomotives were selected for the calculation of proposed shock indicators (ISO 2631 (5)). Results There has been little change in basic locomotive cab and seat design in the U.S.. Two locomotive cab design concepts are used: the Association of American Railroad (AAR) Control Stand and in newer series wide-body locomotives the “Control Consol” (Figures 1-2), with varying seating conditions, but frequently subjecting the operator to an awkward body posture in addition to the vibration and shock exposure. [ ]

Jan 6, 2006

Start with your assessment of the minerals business —domestic mining as well as operational and consulting perspectives. As a third generation miner, I have been living the mining business for as long as I can remember. I have watched commodity prices produce boom and bust cycles in places like Price, Utah (coal), Douglas, Arizona (copper) and Eureka, Nevada (gold). It is unsettling to see how our industry has fluctuated, but it always seems to rebound if you can stick out the down cycles. However, our most recent dip in the cycle was, in my opinion, characteristically and permanently different. In the past, when prices went south, people hunkered down and waited out the cycle until things came back, much the same as they had every other time. Not this time. This time, we saw a consolidation of the industry in proportions never seen before. Mega-mergers like Exxon-Mobil, Phelps Dodge-Cyprus and Newmont-Normandy have changed the complexion of our industry forever. And that is true not just of the mining companies; it happened across the supporting business lines as well. As a midsized niche engineering and environmental service provider to the mining industry, companies like mine are few and far between these days. The lean cycle saw many of the small and midsized providers get gobbled up by consulting giants like URS and TetraTech. The mentality of a mega-company, whether a commodity producer or a goods or service provider, is different than that of their small- and medium-sized counterparts.

Jan 1, 2005

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By G. L. Smith

As the Platinum mining industry expands in the Eastern Limb of the Bushveld Complex it is increasingly evident that a major constraint to development is a lack of appropriate infrastructure. Of critical concern are water resources and spatial development / infrastructure. This paper identifies the context for infrastructure development in the Eastern Limb and two solutions that have evolved in the areas of water supply and spatial development. INTRODUCTION In an economics context, infrastructure is considered to be the structural elements of an economy which allow for the production of goods and services, without themselves being part of the production process. Despite the lack of a specific definition, infrastructure has largely become understood as to comprise road and rail transport systems, public transport systems, airports, public educational facilities, water supply and water resources, wastewater management, solid waste treatment and disposal, electric power generation and transmission, telecommunications and hazardous waste management systems. Critically it is important to understand that infrastructure not only comprises these physical elements but also the operating procedures, management practices and developmental policies that facilitate the effective utilization and development of the infrastructure in response to societal demand.

Jan 1, 2008

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004