Search Documents

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

By M. T. Shehata, R. W. Revie, M. Elboujdaini

Environmentally assisted cracks in linepipe steels are initiated either as a result of stresses in combination with environmental effects, as in stress corrosion cracking (SCC), or as a result of trapped hydrogen in the steel, as in hydrogen-induced cracking (HIC). To understand better the mechanism of the crack initiation process, key metallurgical and environmental elements that can affect the cracking phenomena were investigated and are reviewed in this paper. The complexity of both cracking phenomena results from the dependence of SCC and HIC on multiple metallurgical, mechanical, and environmental parameters that may all influence both crack initiation and propagation; e.g., composition, microstructure and non-metallic inclusions in the steel, applied stress, water chemistry in the field, and ionic concentrations in the groundwater near the pipe surface to name a few for SCC. In addition, for HIC phenomena, one can add the concentration of H2S in the fluids transported in the pipe as well as concentration of CO2, pH, etc. In this paper, cracking of linepipe steels is analyzed critically, with particular attention to the crack initiation process. The paper is divided into two parts: The first part covers SCC and the second covers HIC.

Jan 1, 2005

By J. Fresnillo, M. Lopez Cano, S. Burgada, P. Couceiro, A. Jafa

This paper explores the sustainable use of the explosive’s energy for rock blasting and its role on the performance of downstream unit operations in mining applications. Since energy efficiency is becoming important for long term mining strategies, cost-effective optimization strategies are required to increase productivity and revenue while minimizing environmental impact. These optimization strategies involve continuous ability to model and measure all related phenomena and operational performance, integrated under a continuous improvement program where all involved counterparts act in close coordination. Although mining is complex, it can be regarded as a set of interconnected processes, where energy is consumed in a sequence, following all unit operations from the pit to the concentration. In this sense, the performance of downstream operations is potentially influenced by the initial energy input, since the explosive is the source of all energy used for rock fragmentation and heave. In this line, sustainable energy blasting is recognized as one of the main strategies for mine energy optimization projects. Finally, a special case study from an important gold mine in South America is presented, where benefits of a sustainable blasting energy strategies has been proved to deliver important downstream benefits.

Jan 1, 2019

By Ronald J. Riberich

The Mineral Economics and Management Society (MEMS) held its fifth annual conference in Montreal, Quebec, Canada earlier this year. “The Minerals Industry: Responding to the Global Challenge” was the first MEMS conference to be held outside of the United States. About 125 mining- and minerals-related professionals attended. The MEMS program included six sessions and three distinguished speaker addresses. The session topics included: “Minerals in the Macro economy: Development in Demand,” “Trends in Global Metals Supply: The Producers’ Challenge,” “Global Environmental Issues: Policy Perspectives,” “Global Environmental Issues: Quantitative Analysis” and “Minerals in the CIS: Phoenix or Albatross?” A student session was also offered. It provided a competition for monetary awards for outstanding papers.

Jan 1, 1996

By P G. Hicks

The influence of feed size and pulp density on the specific rate ofbreakage of quartz was investigated. Plots of log fraction of feedremaining within the feed size interval against grinding time allowed the application of the first order grinding model to be examined. Substantial non-linearities were observed for all feed sizes due to environmental and material factors. For feed sizes above 1.3 mm, the specific rate of quartz breakage was higher with rod milling than ball milling, but below this size the reverse was true. Material that remained in the feed size interval after the initial grinding broke more slowly in subsequent grinding than the original feed material. Grinding media and time as well as feed size influenced the effects of pulp density on grinding. More dilute pulps (eg 50 per cent solids density by weight) were favoured for higher rates of breakage in rod milling but for ball milling, the optimum pulp density appeared to be 60 to 70 per cent solids by weight.

Jan 1, 1998

By S. Klingmann, G. Blackwell

"Terrestrial photogrammetry has been used for many years to build three-dimensional pictures for analytical purposes. Photographs can include images from open pit mine walls, ground topography, mine buildings infrastructure or accident scenes. Analysis and co-ordinate estimation in early photogrammetric systems demanded the use of specialized and costly optical-mechanical stereocomparators. Few of these instruments could be interfaced with computers to provide databases, and all required trained personnel with good perspective vision to collect data.Digital photogrammetric software has replaced these older systems, and the digital video plotter (DVP) is a simple computerized system utilizing readily available PCs to quickly produce a stereoscopic model of any scene where an area of overlap exists in photographs taken from two different locations. Specialized cameras providing reference marks or grids on the photographs are still necessary for detailed analysis in three dimensions.This paper describes the application of DVP to the three-dimensional analysis of strike, dip and location of dominant fracture planes visible on an open pit wall slope, and the intersection of planar features which might reduce wall stability. Where reference survey points cannot be provided because access by personnel to the photographic scene is impossible for safety reasons, normal case terrestrial photogrammetry can provide the necessary control points for more complex aerial photogrammetry geometries.DVP recreates the geometry existing at the moment photographs are taken, providing the user with the ability to safely recreate, compare and analyze the structures determining the stability of open pit wall slopes."

Jan 1, 2003

The International Symposium-cum-Workshop on Management andControl of High Gas Emissions and Outbursts in Underground CoalMines was held in Wollongong in March 1995. Coverage of high gasemissions was virtually confined to instantaneous outburst implications, essentially seam gas pre-drainage. Globally, instantaneous outbursts have been known for 150 years, andthe first Australian outburst occurred in 1895 and Australian occurrences and mines affected have increased since. Few significant coal producing countries are unaffected. The coals affected range in rank from lignites to anthracites. Geological disturbances are the most likely environments for occurrences. The most likely mining geometry is of virgin headings, with some occurrences on longwalls and in other situations. Widespread research into many aspects of the problem has yet to produce a generally accepted explanation. Explosive inducement is a well-known control. Apparently high advance rates increase face gassiness and create higher stress abutments, increasing proneness. The most popular preventive measure, pre-drainage of virgin coal ahead of faces has produced highly successful very long hole drilling performances but without the precision necessary for accurate geometric hole patterns, despite quite sophisticated drilling equipment and hole surveying instruments. For the future, more precise degasification is sought, even from the surface, together with rapid face coal gassiness assessments to confirm lowering below threshold values, as well as other proneness lowering measures, perhaps related to new heading and longwall geometries and to new equipment to provide them. But above all, safe management plans are required for each operation, to safeguard the miners and their working environments, and thus to protect underground coal mining from this mounting threatening problem.

Jan 1, 1997

By Ian McFeat-Smith

Despite a present, short-term economic recession, a remarkable enthusiasm exists in Hong Kong for building infrastructure including major tunnel projects. This paper provides details of current and recent bored tunnel works together with an insight into the impressive list of future underground projects planned by the MTRC,KCRC, Highways Department and Drainage Services Department for the next decade. Risks for each of these works including pipejacking, mixed face and rock tunnelling generally in Hong Kong are also identified. From this is evident that the scale and difficulty of such works continues to increase, requiring the use of more sophisticated methods of construction, the need for better methods of assessing and managing risks and for Government to utilize improved, more equitable Conditions of Contract for such major tunnelling projects.

Jan 1, 2001

Mining and oil industry representatives are scheduled to testify May 15 at hearings on the Simpson bill to extend the Reciprocal Trade Agreements Act, Several Congressmen have introduced bills to extend present trade agreements without modification. Price of copper appears to be stabilizing at 30[] per lb, after a period where market price ranged from 27 to 34[]. Copper offerings from abroad were finding no takers at 30.24[] per lb late in April.

Jan 5, 1953

Jan 1, 1969

By Brenda Myers-Bohlke, Tor L. Brekke

INTRODUCTION In recent years several cities in the Eastern United States have constructed subway systems in deeply weathered igneous and metamorphic rocks. Portions of these transit tunnels and shafts have penetrated zones of saprolite. The purpose of this paper is to define saprolite and discuss saprolite behavior in terms of construction and design of tunnels and shafts. Saprolites are products of in situ weathering of rock, with properties intermediate between those of soil and rock. A well-developed weathering profile can be divided into zones of residual soil, saprolite, transition zone materials, weathered rock, and fresh rock. Saprolites are distinguished by a high degree of weathering and by retention of parent rock textures and discontinuities. These structures persist as relict features because of iso-volumetric weathering (Cleaves, 1974) and formation of intergranular bonds that give cohesion to the saprolitic material. As saprolite continues to weather, the bonds are broken, causing the saprolite to decompose and disintegrate into a true residual soil mass without relict structure. Saprolites may form from igneous, metamorphic or sedimentary rocks, but are most easily recognized when derived from igneous and metamorphic rocks because of their inherent structures. The physical characteristics and properties of residual material vary as a function of mineralogic composition, structure, and discontinuities of its parent rock.

Jan 1, 1985

By Ivan Imris

The common problem of new and conventional technology of copper production is the copper losses in the slags, which may be divided into mechanical and physico-chemical losses. In the first group can be included particles of mechanically entrained or floated unsedimented matte particles which coexist with slag. On the other hand, the physico-chemical losses are caused by solubility of copper in the slag in the form of sulphide and oxide. The copper losses in the slags from different processes has been predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and quantitative electron microprobe analysis. Depending on the forms of copper losses in the slag the reduction of copper losses in the slag or the slag cleaning process could be suggested.

Jan 1, 2003

By E. Gutierrez, P. Gillies

Asset Maintenance Readiness (AMR) provides a tailored reliability and maintenance strategy specific to operational needs. AMR delivers reliability and maintenance foundations for the plant and equipment before start-up. Having a dependable reliability and maintenance strategy before start-up is critical, particularly in those first weeks and months during ramp up to stable production. The Asset Maintenance Readiness is the integration of Reliability and Maintenance Engineering analysis/studies at the earliest stages of the new Production System concept and design and during the Capital Project CapEx phases; adding this analysis to the Capital Project CAPEX cost, will have an impact of 2% to 3% of total project cost, but will deliver a good compendium of benefits far from the AMR costs, and those results will be shown upon commissioning and during the life cycle of the plant.

Mar 2, 2022

By E. W. Davis

I . OPERATING TESTS 1. CHARACTER OF ORE UNDER INVESTIGATION On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite . The magnetite comprises about 35 per cent. of the rock. Fig.. 1 show's graphically that the tonnage of minus 200-mesh material produced varies directly with the tonnage fed to the mill. There is undoubtedly some limit to this relation, but there seems to be no indication of it at 18 T. per hr. Some of the conclusions drawn from this test are that: (a) The ball-mill is naturally a machine of very large capacity; (b) if it is not possible to deliver a large tonnage of original feed to the mill, a closed circuit should be provided so that the mill may crush its own oversize.

Jan 2, 1919

By LeRoy D. Loy

Would you believe me if I told you the constant battle between Government regulatory agencies and industry could be won by both sides? No, I'm not crazy, nor have I been soaking up any of that fine Kentucky whitelightning. But I have recently been a participant in a battle where both sides won. Actually, I'm using the term "battle" loosely because, in reality, it wasn't a battle at all - despite the fact that all the ingredients were there for a monumental struggle; i.e.. government, industry, special interest groups and a controversial issue - the development of effluent limitations. I'd like to tell you about it. Historically, on one side of the battle, government has always been ac¬cused of adopting regulations with limited evaluation of existing technologies; and then with seemingly no regard for the economic consequences. On the other side, industry gets punished by government's harsh actions because of their past "do-nothing" attitude toward pollution control. Recently, this battle seems to be losing steam, because both government and industry are beginning to realize that, ultimately, they both will lose. Even more important is the fact that both sides are, or should be, working for industrial expansion compatible with environmental protection.

Jan 1, 1977

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By Staton L. Tainter

"The Johnny Bull and Silver Knight claims were selected for exploratory diamond drilling after having been examined by the Bureau of Mines 3./The property was considered attractive for two reasons: (1) A prominent outcrop, recognized as an extension of the Tennessee vein, persisted over a distance of 2,000 feet across the claims; (2) its proximity to the known ore shoots in the Tennessee-Schuylkill mine, one of the largest zinc-load producers in Arizona.Actual drilling was started September 18 and was terminated December 8, 1943. Eight holes, aggregating 2,979.5 feet, were drilled with two machines. ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resource to the end that they make the greatest possible contribution to national security and economy. I is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R.G. Knickerbocker, chief, analyses samples and performs beneficiation tests."

Jan 1, 1947

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014