Search Documents

In 1948, it became clear that the ventilation system of The Zinc Corporation Limited and New Broken Hill Consolidated Limited mines, would be inadequate for future operations. The,paper describes in detail the process of designing an entirely new ventilation system for a large underground mining operation. The system was based on a single new upcast airway to be located on the boundary of the two properties, which were to be ventilated in parallel as two separate ventilating districts.From calculations of resistance, and assessments of future air requirements, the duties of a new exhaust fan to be located on the collar of the upcast airway were specified as 700,000 cubic feet per minute at 2·6 in. w.g. total pressure for initial operation in 1953 increasing to a maximum of 900,000 c.f.m. at 3·6 in. w:g. total pressure ten years later. The economic size of the new airway was calculated from a consideration of the first thirty years operation of the system, and it was decided to provide a 20 ft. diameter concrete-lined shaft.The new system went into operation five years after the initial planning, and the effect of the difference between actual and predicted rates and distribution or production are discussed. The final result was entirely satisfactory.INTRODUCTIONThe first proposal for an investigation of The Zinc Corporation Limited-New Broken Hill Consolidated Limited ventilation system with a view to putting it on a proper technical basis was made in 1938. A new Main Shaft was then being sunk, and it was decided to postpone the enquiry until this had been completed to No. 14 Level, when operations would be temporarily suspended and the shaft commence to operate as a major airway. The investigation was completed early in 1940, when Z.C. Ltd. upcast fan was...

Jan 1, 1956

By Donald Markle

ANTHRACOAL is a mixture of small particles of anthracite coal and a matrix of practically pure carbon, formed from the distillation of coal-tar pitch or other suitable bitumen. It is a hard, dense, homogeneous mass, with a silvery luster and in color varies from silvery to grayish black. When pushed from the oven, it develops only partly the fingerlike structure of coke; but, unlike coke, it has a tendency to remain in blocky masses. When struck with a hammer or passed through crushing rolls, it breaks with an irregular fracture, similar to anthracite, but with very little fines. Due to its density, anthracoal is harder, tougher, and stronger than coke. The results of a test made by the blast-furnace department, of the Bethlehem Steel Co., on two barrels of anthracoal are given in Table 1. TABLE I.-Results of Shatter Tests on Anthracoal and Coke Anthracoal Test Good Blast-furnace Coke First Second Barrel Barrel Moisture, per cent 0.77 0.76 Under 5, variation not over 3 points Sieve test Through 2-in. screen, per cent 7.71 7.29 Under 40 Through 1-in. screen, per cent 1.37 1.56 Through ½ -in. screen, percent 0.93 1.08 Under 8 Over 2-in. screen, per cent 92.29 92.71 Over 60 Shatter test Through 2-in. screen, per cent 10.06 ' 12.40 1 Under 16 Through 1-in. screen, per cent 2.66 2.06 Through ½ -in. screen, per cent 1.80 1.26 Over 2-in. screen, per cent Hardness number 86.40 86.10 Over 81 Analysis Ash, percent 16.64 16.48 Under 11 Sulfur, per cent 1.17 1.10 Under 0.95 Volatile matter, per cent 0.77 0.27 Fixed carbon, percent 82.59 83.25 Over 87

Jan 8, 1921

By J. S. Limb

Actual issues which arose during the discovery process or subsequent court testimony are presented. While most of these issues relate to the author’s specialty of mineral appraisal some are more general in nature and could be of interest to those who may be involved in current or future court testimony. Several important areas to be reviewed and agreed upon with the client and their legal counsel are discussed. General observations on litigation, the discovery process, testimony and some repercussion’s are also given.

Jan 1, 2001

By AIME AIME

THAT the copper industry is in serious straits is admitted. So are the lead and zinc industries, and both lead and zinc are tariff protected. Conditions in the Western lead, zinc and silver mining districts are desperate. These are illustrated by the present disastrously low prices of these metals compared with the levels of two and three years ago and by the comparative rates of metal production and the present activity of the western mining camps. The January production of copper was 32.2 per cent of the 1929 average rate, of steel was 32.3 per cent of the 1929 average, while January production of pig iron was only 27.6 per cent of the monthly average of 1929. The copper industry is only one of many industries that are suffering in this tragic depression. It has been exceedingly prosperous and will be prosperous again when business recovers. Its difficulties are not unique and it does not deserve the tariff equivalent of a dole. The burden of subsidizing through an effective tax or tariff the minority group of high-cost mines would be a heavy one on the consuming public of the United States. On the basis of 1929 consumption figures, an effective 5c. tariff would result in an increased copper bill to the country of over $109,000,000, of which the electric manufacturers would contribute $26,000,000, the telephone and telegraph companies $16,000,000, and the automobile manufacturers $14,000,000. And of this total bill, only $33,000,000 would go to those who are urging a tariff and the balance of $76,000,000 would be paid to those who do not admit either its necessity or usefulness under present conditions.

Jan 1, 1932

By J. Moore Samuel

THE prospective change in ore receipts at the Copper Queen reduction works necessitated a careful study of conditions to determine the most economical method of smelting. The first step, calculating the known, probable, and possible results, showed the economy of a unimetallurgical flow sheet f which the three pyrometallurgical stages would be roasting, reverberatory smelting, and converting. The past and future ore receipts (not including converter flux) are as follows: AVERAGE MONTHLY FUTURE MONTHLY RECEIPTS, 1918 RECEIPTS TONS PER PER CENT. OF TONS PER PER CENT. OF MONTH TOTAL RECEIPTS MONTH TOTAL RECEIPTS Ore 84,553 82.3 43,000 44.0 Gravity concentrates 16,375 15.9 25,500 26.0 Flotation concentrates 1,883 1.8 29,400 30.0 Total 102,811 100.0 97,900 100.0 Of the 102,811 tons per month received in 1918, only 28,945, or 28 per cent., was treated in the roasters and an average f 14.1 roasters out of 20 were in operation; the remaining ore was treated in the blast furnaces. The change to "all reverb." practice, therefore, called for considerable additional roaster capacity, which could be obtained either by building additional units, or by remodelling the present units so as to give increased unit capacity. In view of the progress in roasting practice since the construction of the Copper Queen roaster plant and the heavy investment in that roaster plant, the second plan seemed to be the more desirable. The Copper Queen roaster plant consisted of twenty six-hearth, McDougall roasters, 18 ft. in diameter, equipped with cast-iron arms that originally were water cooled but now are air cooled. They have no top dry hearth and the feed is discharged through the top arch, near its periphery, by plunger feeders from two bins at opposite sides of the roaster.

Jan 7, 1921

By A. Trusiak

"Increasing energy costs in mineral processing is making it necessary for tighter controls over various parts of the concentrating process. Continuous monitoring and control of critical process streams can be easily performed by today's many computer systems. Indeed, the list of successful applications of computers to grinding and flotation control continues to grow. The day is rapidly approaching when the use of computers within concentrators for either process control or simply metallurgical accounting will no longer be a luxury, but a necessity. The benefits from such applications far out weight the initial investment.This paper describes the current application of a process control system at Brunswick Mining in north-eastern New Brunswick. Emphasis is placed on the control of a CuPb flotation circuit, and the benefits derived-from this control.No. 12 Cu-Pb Flotation: The complex nature of the Brunswick flotation process has been described else-where. 1,2,3 Four final concentrates are eventually produced, these being a Zn concentrate assaying 53% Zn, a 30% Pb concentrate, a 20% Cu concentrate, and a bulk Pb Zn concentrate assaying 35% Zn and 17% Pb. The Cu concentate, Pb concentrate, and bulk Pb Zn concentrate are all derived from a primary CuPb concentrate assaying 26% Pb, 11% Zn and 1.8% Cu.The No. 12 CuPb circuit produces approximately two thirds of the total primary CuPb concentrate. No. 12 ore, assaying 3.5% Pb, 9% Zn, 0.25% Cu and 100 g/tne silver, is ground in two parallel grinding circuits. Each line uses a 3.2 x 4.2 meter rod mill in closed circuit with two parallel 3.2 x 3.9 meter ball mills. Ball mill and rod mill discharges are classified in two stages of cycloning. The secondary cyclone overflow, or flotation feed, is controlled at 65% passing 37 microns."

Jan 1, 1981

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By R. U. Jackson

Belt conveying is a method of transportation that requires proper servicing and maintenance if completely economical results are to be obtained from the system. With a trucking system, it is common practice to deliver the trucks to a servicing station each day or at the end of each shift. With railroad transportation there is a similar procedure. Sufficient credit is seldom given to this periodic inspection and maintenance procedure, yet it is the key to the successful operation of trucking and rail haulage systems. How about the belt conveyor transportation system? Here is a system that requires no operator for each individual unit. It requires only a main switch and an adequate sequence interlocking system, and the system is so simple to operate that maintenance is considered as only a casual requirement-nothing is done about it until after trouble has developed.

Jan 1, 1956

By Patricia Martínez Nicolás

Nickel and ferronickel are some of the major components in the production of special alloys; however, the energy consumption for their production greatly increases their price. A cheaper option could be to use NiO and a reducing agent. This work presents experimental and theoretical analysis to estimate the effect of slag basicity and amount of reducing agents on the NiO reduction from the slag which interacted with molten steel at 1600 °C in an EAF. The slag system contained CaO, SiO2, CaF2 and NiO together with a reducing agent, ferrosilicon or carbon. The NiO content in the slag was 25 mass%. The amounts of the reducing agents (Si and C) were 1 to 4 times the stoichiometric mass to reduce NiO. The CaO/SiO2 ratio was 1.5 and 2.5. The kinetics of the process was very fast since after few minutes the maximum nickel yield was obtained. The slag basicity had a negligible effect on the reduction of NiO.

Jan 1, 2006

"With a total value to date of well over $200,000,000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $ 100,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper.Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade.In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1 924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.The known mineralized area of the district is found in a broad syncline striking north and south. The west limb plunges sharply and extends for a distance on its dip of approximately one and a half miles to the trough. The east limb raises gently through a distance of about two miles to the east limit of known mineralization. This general structure is broken by local faulting throughout the district, the local structural conditions playing an important part in the ore deposition. The north end of the fold is obscured by a rhyolite flow and the south end stops against a monzonite stock."

Jan 1, 1925

By S. G. Hardcastle, C. K. Kocsis

In Canada’s metal mines, ventilation, which requires electricity to operate the fans and fossil fuel for heating, accounts for a significant portion of the overall mine’s underground power consumption. Mine ventilation systems are usually designed near the end of the mine design process and often designed for the ‘worst-case-scenario’ with respect to ventilation demand. In Canada’s metal mines this is commonly dictated by either diesel equipment usage or heat management considerations. Once designed, mine ventilation systems tend to operate at this peak level throughout the operating life of the mine. This is despite there being significant periods when this quantity is not required this is done mainly due to lack of appropriate ventilation controls. Consequently, such systems are inefficient and wasteful and this must be changed if mining operations are to remain competitive while meeting increasingly more stringent regulations of underground environmental conditions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. The tools used for this include several disparate types of software. A developing trend is to design and plan the mine using orebody modelling software, followed by using discrete event simulation to predict production and evaluate various operating scenarios. It seems that again ventilation design is not being integrated into this process. Although, several modelling packages exist for ventilation design, little work has been done on integrating ventilation modelling into the overall life cycle plan of the mine. This paper will present a discussion of the work where the authors are attempting to integrate discrete event simulation for mine planning with ventilation modelling to predict the ventilation requirements for the operating life of the mine.

Jan 1, 2003

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By S Jahanshahi, D R. Swinbourne

A knowledge of the value of the activity coefficient of cobalt oxide in slag as a function of composition and temperature is necessary if effective strategies are to be devised to maximise the recovery of cobalt in nonferrous smelting processes. This work reviews previous studies and shows that comparison and evaluation of the results is hampered by variations in the choice of standard states for the species. Published results have been recalculated to a common set of standard states with a preferred value for the Gibbs free energy of formation of cobalt oxide. It has been shown that the value of the activity coefficient of cobalt oxide referred to the solid standard state in iron silicate slags is approximately two, at temperatures from 1523 to 1623¦K. It is suggested that some contradictory results are most likely due to errors in the measured partial pressure of oxygen.

Jan 1, 1998

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

By R. A. Jankowsi, S. K. Ruggieri

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the "shearer-clearer," to push the dust close to the face. The techniques have been evaluated in field trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 6, 1985

Diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for ventilation.

Jan 6, 1985

By S. G. Malghan

W.H. Moyer In reference to the section “Excess pyrite, ” the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, “An Improved Flotation Method for Cornwall Sulfides. ” While it was not used on a porphyry copper ore, it was used on a chalcopyrite - pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a highgrade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6q. Cu grade chalcopyrite product and a pyrite analyzing 0.0670 Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The “differential” separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 11, 1986

By J. W. Town

The Bureau of Mines conducted phosphate beneficiation studies to determine the influence of mineralogical and textural features on the recovery of phosphate from select bed and composite samples representing different phosphate rock types of the western Phosphoria Formation. Batch heavy-liquid tests showed that ore grade) pellet size, and type of interstitial material were significant parameters affecting concentrate grade and recovery. Recoveries at acid grade (31.5 percent P2O5) ranged from 98 to 56 percent. Liberation was essentially complete at 28 mesh, and recoveries tended to drop when overgrinding occurred.

Jan 1, 1966

By Drew GJ

Smelting is a process in which heat is applied to ores to produce metals. Impurities are removed by segregation in the slag, or converted to gases or sublimates and discharged up the flues. Mate- rials delivered into the smelter have generally been previously concentrated or processed at the mine, and the size of their particles, and also their chem- ical composition, greatly affect the smelting proc- ess. Some impurities are more difficult to remove than others, and are more objectionable in the finished product. The first metal mine in Australia was opened near Glen Osmond in South Australia in 1841, for silver-lead ore. It was followed by the Kapunda Mine for copper in 1844 and by the very signifi- cant Burra Mine, also for copper, in 1845 (Figure 1). A major part of their ores could not be exported profitably for smelting in England and Wales where the large smelters were then located. In addition to treating ores from Cornwall these also smelted ores from recently opened mines in Cuba, Chile, and Mexico. The Welsh smelting process (Figure 2) was developed over a period of years to utilise Welsh coal to treat copper ores particularly from Corn- wall. The first step consisted of a calcination to remove sufficient sulphur from sulphide ores so that subsequent melting operations would produce copper matte, a copper-iron-sulphide which melted at about 1050¦C. Subsequently refined to white metal with the addition of carbonate and oxide ores when these were available, and often through an intermediate step of blue metal, this matte was finally oxidised to pure copper, or as pure as it could be made in those days. The movement of metal towards greater purity was matched by a reverse flow of slag, carrying reducing quantities of copper, so that the slag rejected from the first melting process carried the minimum quantity of copper. Chemical analysis was virtually unknown. Materials were assayed in the laboratory by a small scale smelting process, and the purity of the final refined copper was judged b} the ease with Mhich it could be hammered into thin sheets.

Jan 1, 1987

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998