Search Documents

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

By L. A. Haas

The U.S. Department of the Interior, Bureau of Mines, is conducting laboratory-scale research to determine the leaching conditions required with sulfuric acid for extracting base metal from a matte with a copper-to-nicke1 ratio of 6 to 1. The matte (61.2 pct Cu, 9.7 pct Ni, 3.3 pct Fe, 21 pct S, and about 5 oz of precious metals per ton) was prepared from Duluth Complex (Minnesota) ore by smelting a bulk sulfide flotation concentrate. The matte was pre leached at atmospheric pressure to selectively extract 20 pct of the nickel, and the undissolved solids were referred to as the matte residue. Autoclave leaching of the matte residue extracted over 95 pct of the nickel, copper, and iron. The remaining leach residue in the autoclave contained over 100 oz of precious metals per ton. The leaching conditions required were matte grind of greater than 98 pct minus 325 mesh, pulp concentration of 50 g/1, total pressure of 100 psig with oxygen at 150° C or 400 psig with air at 180° C, 50 g/1 H2S04, 700 rpm agitator speed, and 6 hours of leaching time. The leaching time was decreased to 2 hours by increasing the agitator speed to 1,300 rpm. Sulfuric acid concentration greater than 50 g/1 did not appreciably enhance the base metal extraction, but with less acid, residues with higher iron concentrations were obtained. Supersaturation of the liquor was prevented at 150° C by using a 1ixiviant that contained 30 g/l Ni and 20 g/1 Cu.

Jan 1, 1979

By J. Trojacek

A large-scale development in exploration and production of uranium ores in the Czech Republic was done in the 2nd half of the 20th century. Many uranium deposits were discovered in the territory of the Czech Republic. Over a period of 50 years approximately, 110 000 tons of uranium in concentrate were produced. Different mining methods were developed and used. One of the most considerable deposits in the Czech Republic is the site Hamr na Jezere ? Straz pod Ralskem where both mining methods ? the underground mining and the acidic in-situ leaching ? were used. The extensive production of uranium led to widespread environmental impacts and contamination of groundwaters. Over the period of ?chemical? leaching of uranium (ca. 32 years), a total of more than 4 million tons of sulphuric acid and other chemicals have been injected into the ground. Most of the products (approximately 99.5 %) of the acids reactions with the rocks are located in the Cenomanian aquifer. The contamination of Cenomanian aquifer covers an area larger than 27 km2. The influenced volume of groundwater is more than 380 million m3. The total amount of dissolved SO4 2- is about 3.6 million tons. Approximately 0.5 % of the contamination is located in the Turonian aquifer. After 1990, a large-scale environmental program was established and the Czech government decided to liquidate the ISL Mine and start the remediation in 1996. The remediation consists of contaminated groundwater pumping, removing of the contaminants and discharging or reinjection of treated water. The objectives of the remedial activities are the followings : to restore the aquifer to a condition guaranteeing continuing usability of Turonian water of Northern Bohemia Cretaceous, to decommission boreholes and surface installations and to incorporate the surface of leaching fields into the ecosystems taking into account regional systems of ecological stability and urban plans. Nowadays four main remedial technological installations for reaching of these aims are used - the ?Station for Acid Solutions Liquidation No. One?, the ?Mother liquor reprocessing? station, the ?Neutralization and Decontamination Station NDS 6? and the ?Neutralization and Decontamination Station NDS 10?. Total capacity of this complex is sufficient to reach the target values of remedial parameters in 2037. The remediation action consists of: pumping of residual solution to the surface, separating uranium from the solution and reprocessing contaminants into commercially usable or ecologically storable products. It is expected that the amount of withdrawn contaminants will vary from 80 000 to 120 000 tons per year. Total costs of all remediation activities are expected to be in excess of 1.5 billion EUR.

Aug 1, 2013

By M. Mezbahul-Islam

Thermodynamic modeling of the Mg-Cu-Ni system is carried out as a part of multi component thermodynamic database for Mg alloys. This system is being modeled for the first time using the modified quasichemical model, which considers the presence of short range ordering in the liquid. The thermodynamic descriptions of the binaries Mg-Cu, Cu-Ni and Mg-Ni have been extrapolated to the ternary Mg-Cu-Ni system using Toop geometric model. The constructed database has been used to calculate and predict thermodynamic properties, isothermal sections and liquidus projections of the Mg¬Cu-Ni system, which showed very good consistency with the experimental data.

Jan 1, 2011

By J. H. McClain

In the last 3 years' operation of the zirconium-production plant, zirconium metal has been employed to good advantage in many applications. The most frequent use has been in situations requiring resistance to attack by hydrochloric acid. In this service, it has been shown to be a serious competitor to Hastelloy. Zirconium also has excellent resistance to most other corrosives end could be considered for use as an all purpose metal. For example, this report cites 18 applications in hydrochloric acid, 4 applications in sulfuric acid, 5 applications in phthalic-hydrochloric acid, 3 applications in wet hydrogen chloride-chlorine atmospheres, and 2 applications in fused caustic.

Jan 1, 1954

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite / Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007

By Joshua Calnan, Braden Lusk, Kyle Perry

This paper presents detailed information and data regarding the load transfer characteristics of Blast Resistant Glazing Systems utilizing two different thicknesses of polycarbonate. A series of triaxial load cells, along with surrogates of identical stiffness characteristics, were placed around the glazing perimeter to directly measure the load transferred to the support system from explosions of varying degrees. The blast loads were developed using an explosive driven shock tube administered by the University of Kentucky Explosives Research Team (UKERT) in Georgetown, KY. Results presented include distribution of loading, maximum load transferred to connections, blast pressure-time data, glazing system deflection-time data, and final performance results of each system. The two glazing systems respond differently to the applied blast loading. Differences and similarities in the load transfer characteristics are discussed. The experimental results are then compared to a commonly used blast resistant glazing system analysis software tool utilizing a Single Degree of Freedom (SDOF) method of analysis for each system. Preliminary results show that currently used models do not correspond well with experimental data.

Jan 1, 2014

By M. J. Ankeny

Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the prevention of such accidents will materially improve progress in safety in the coal-mining industry. Beginning March 1950, Federal coal-mine inspectors were made responsible for completely investigating all fatal accidents in and around coal mines. During these 10 months, Federal coal-mine inspectors investigated 447 fatal accidents. This is a study of 121 of the fatal haulage accidents investigated, which constituted 27 percent of fatalities from all causes. Haulage employees represent only 12 to 15 percent of mine personnel, but, on the basis of accident frequency, their work is the most hazardous in coal mines. Fatal haulage accidents occurred in 53 bituminous coal-producing counties representing 14 States and Alaska. The physical conditions represent a cross section of' producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of modern mechanized mines.

Jan 1, 1951

By Nissandro Domingues

Foi avaliada a possibilidade de aumentar a produtividade do aço IF processado via recozimento contínuo. Amostras laminadas a frio desse aço foram submetidas a ciclos térmicos de recozimento em escala laboratorial, empregando-se menores temperaturas de encharque e maiores velocidades de processamento que as praticadas industrialmente. Foram, então, medidas as propriedades mecânicas em tração e caracterizada a microestrutura do aço. A partir dos resultados mais promissores, bobinas foram processadas industrialmente nas mesmas condições simuladas em escala laboratorial. Em amostras dessas bobinas, foi avaliada, além das propriedades mecânicas e da microestrutura, a conformabilidade de blanks visando à garantia de atendimento dos requisitos de aplicação no cliente. Com os resultados obtidos, verificou-se que é possível produzir o aço IF satisfatoriamente, preenchendo todos os requisitos de aplicação, com um incremento de 10% na velocidade de processamento e uma diminuição de até 30°C, na temperatura de encharque. Esses resultados representam considerável ganho em produtividade no processamento do aço IF.

Aug 17, 2017

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By A. Adu-Acheampong

Photogrammetry and laser scanning has been employed at a number of Newmont mine sites to mitigate risks associated with conventional structural mapping, determining the geometry of voids from old underground workings, and generating topography in areas of slope instability. Laser scanning has also been used to evaluate as-built pit slope configurations with respect to design assumptions, operational practices, and rock fall potential. Recently, remote sensing applications carried on an unmanned aerial vehicle (UAV) were used to generate base topography at some Newmont sites. UAV are generally more convenient and less expensive and can be utilized in areas where cloud cover prevents manned aerial photography missions. This paper discusses these applications, and provides commentary on their benefits and limitations based on recent experience.

Feb 27, 2013

By Pierre Gauthier

Is the hydrogen economy of the future just another fish story? Absolutely not! There have been many changes affecting the energy equation over the last 10 years and conditions have changed. In this presentation, we will examine the reasons why, in the very near future, hydrogen production and distribution will be increasingly visible on many industries? radar screens.

May 1, 2007

By P. M. Prasad

The last two decades have witnessed the emergence of numerous hydrometallurgical and direct processing techniques for the extraction of some metals from pocketed/lean/complex sulfide ore deposits. A new approach with some inherent technological merits, investigated in recent years, is the lime-enhanced reduction of metal sulfides. Thermodynamic aspects relevant to the lime-enhanced reduction of metal sulfides by H2,C0 and C are discussed. A survey of the researches on the basic features of and factors influencing the lime-scavenged reduction of selected sulfides and sulfide concentrates reveals that lime tremendously enhances the sulfide reduction rates (up to 100 times) and drastically reduces the sulfur emission into off-gas to negligible levels. Further successful practice of lime-enhanced reduction requires only a moderate temperature of reduction (characteristic of each sul¬fide) and, in the case of gaseous reduction, relatively low gas flow rates. Relevant kinetic aspects of the concerned reactions that have a bearing on process development and its understanding are also briefly discussed. A conceptual scheme of general applicability for the processing of sulfide concentrates by the lime-enhanced reduction technique consists of three main steps: (0 lime-enhanced reduction by a suitable reagent (e,g., H,2, CO, gasified coal, water gas), (ii) separation of the product metal from the dry slag (CaS + unused CO) by mechanical separation, magnetic/gravity concentration or flotation and (iii) melting and refining by standard procedures. This novel approach, which is patently less complex, is expected to employ basically simpler flow sheets at comparatively lower operational temperatures and aid in pollution abatement. Potential for developing such a route for the small scale extraction of metals like copper, molybdenum and antimony is indicated. Possibility of utilizing this technique for the production of fibers/ filaments of some metals is also outlined.

Jan 1, 1983

By Ray Slavin, Remi Proulx

The Meikle Mine is a mature underground gold mine utilizing primary and secondary longhole open stoping method with delayed backfill. Combined production with the newly developed Rodeo Mine is 4700 tons per day (4265 tonnes per day) of ore. The vast majority of Meikle Mine production comes from secondary and remnant stope blocks. Remnant stopes are ore blocks that were left behind in the initial mining sequence due to various reasons. Mining of these remnant blocks has created many challenging blasting situations. The application of electronic initiation to blast remnant stopes has proven extremely beneficial. Electronic initiation has provided the blasting engineer with a high degree of flexibility with respect to timing to successfully extract these difficult stopes. Post blast assessment of the remnant stopes using the mine’s cavity monitoring system (CMS) demonstrates that the mine is maximizing ore recovery and minimizing waste dilution. The largest remnant stope blast to date required 54 holes and produced 6700 tons (6075 tonnes) of ore. Another area where the application of electronic detonators has proved successful is in the extraction of slots in which ground conditions are extremely poor. Taking the slot blasts in one shot with double-decked holes as opposed to two single-decked shots has eliminated the need to clean and or re-drill holes. The ability to open the slots in one blast has helped reduce the total mining cost. This concept has recently been expanded to blast complete stopes in one shot. This reduces the stope cycle time considerably and allows the mine to bring ore forward. Current plans for 2004 are to excavate 50% of mine wide stope production using electronic initiation technology.

Jan 1, 2004