Search Documents

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

For the past 12 years, the Universities of Stellenbosch and Cape Town have hosted an annual symposium to discuss research topics in Minerals Processing. Since 1987, this meeting has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has enjoyed much national and international support. In 1993, in place of the usual Symposium, the Branch and Universities collaborated with CSM Associates Ltd and Minerals Engineering Journal is organizing the international Minerals Engineering '93 Conference in Cape Town.

Jan 1, 1993

By J. H. Gwynne

[ ]

Jan 1, 1962

By Luís Claudio Antunes Ferreira

No atual cenário econômico as siderúrgicas estão buscando cada vez mais a redução dos seus custos para a produção do aço, com o objetivo de manter-se competitiva neste mercado. O custo da manutenção refratária corresponde a um valor expressivo para a produção do aço, portanto trabalhos com objetivos de novas técnicas de manutenção para aumentar a produtividade, fazem com que estes custos sejam reduzidos. A CSN Porto Real é uma filial com vocação para o mercado automobilístico e possui um forno de galvanização. Conforme o plano de manuteção houve a necessidade de troca de todas as chapas de inox do forno da linha de galvanização, pois encontravam-se queimadas e com alto grau de deformação. Esta atividade, por motivo de histórico de execução em um forno vertical, sempre foi realizada com a utilização de um grande volume de andaime e de mão de obra, tendo assim um alto custo para a sua execução. Este trabalho foi fruto do estudo para redução do custo de manutenção com a aplicação da técnica de Alpinismo Industrial para se aumentar a produtividade.

Aug 17, 2017

By Ferid Kromer

This paper is the first in a series which will describe geology, mining methods, and production costs of some, of Turkey's more important minerals. In this paper the economically significant minerals-chromite, meerschaum, and magnesite-of the Tagtepe district are described. The cost data presented are believed by the author to be the first made public on Turkish chromite mining.

Jan 1, 1950

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By Paul Kunze

We have been told many times by legal folks and insurance types about the importance of producing accurate blast reports should you ever get dragged into court. In that venue the investigators will look at the information regarding product type and quantity, it’s distribution among the holes, and delay information in order to arrive at some judgement regarding vibrations or other blast induced phenomena

Jan 1, 2003

Factors which cause thiourea consumption in gold-leaching systems include adsorption by gangue mineral particles, complexation with base metal ions, thermal degradation, and oxidation by air/ferric iron. Of these factors oxidation by ferric iron is the most significant factor. Of course, ferric sulfate is desired as an oxidant for the gold leaching reaction, but an excess of ferric sulfate leads to high thiourea consumption. In this regard, the rate of gold leaching by thiourea must be balanced against the rate of thiourea decomposition. It is important to note that the thiourea decomposition reaction in ferric sulfate solution is relatively slow in pure solutions and has been found to be first order with respect to both thiourea concentration and total ferric iron concentration. However, when mineral particles from gold-bearing ores or concentrates are present, the decomposition rate can become quite significant. As might be expected, the catalytic activity of mineral surfaces varies with particle composition and size. Experimental results are discussed with respect to the consumption of thiourea.

Jan 1, 1997

By M S. Henderson, R D. Alorro, L G. Dyer

An alternative leaching system for rare earth element recovery from monazite is under development. The initial stage utilises oxalic acid to convert the rare earth phosphate into an oxalate salt through dissolution and reprecipitation and it is the efficiency of this stage that governs the overall recovery achieved. It has previously been proposed that lixiviant consumption is the primary limitation in this process. This work further investigates a range of conditions in an attempt to further elucidate the factors influencing the achievable conversion in this stage. It has been shown that the pH may be governed by multiple reactions both consuming and producing acid (thus the mild change over time). The importance of proper mixing and potential to operate at lower temperature with only moderate impact on kinetics has also been demonstrated. Staged/sequential leaching is more effective in fresh solution as opposed to restoring the lixiviant concentration with subsequent reagent addition, suggesting some impact of solution composition. However, contrary to previous findings, subjecting the leach residue to fresh solution resulted in significant decline in leach rate and overall dissolution. This may be because a greater proportion of conversion was achieved in stage 1 in this work than in previous investigation. This may indicate that eventual passivation or the presence of some more refractory REE minerals limits dissolution. Iron dissolution was relatively consistent upon exposure to fresh solution, displaying the ability of the solution to continue to leach the goethite component of the concentrate.

Aug 24, 2022

By Roger K. McLimans, Venkatramaiah N. Vasudev, Christian Knudsen, Stefan Bernstein, Dirk Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) analyses of sediment samples from coastal regions of Kerala and Tamil Nadu states and the heavy mineral deposits of Chavara, South India, show large lateral differences in the titanium content in ilmenite due to varying degrees of iron leaching. As the depositional environments for the sands with varying degrees of ilmenite alteration are comparable, the cause for the different degree of alteration is due to differences in the primary source of the ilmenite or to differences in the geochemical history of the ilmenite grains during transport from source to deposit. The CCSEM analyses of the heavy mineral fractions show that source of sediments with a high content of titanium-enriched ilmenites, mainly the heavy mineral deposit around Chavara, resides in the khondalite belt of South India (granulite facies metasediments). The less titanium-enriched ilmenites are sourced from other rocks in the area such as the charnokites. Those conclusions are based on the high MgO content in the leached ilmenites, chemical composition of the accompanying garnets (low CaO and high MgO), and the concentration of aluminum-rich minerals in the sands.

Jan 1, 2005

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By AIME AIME

THE United Electric Coal Companies, operating large strip mines at various points in Illinois, pioneered in developing and perfecting the strip method of mining coal by use of large shovels and drag-lines. Coal stripping was first started on the properties owned by this company near Danville, Ill., in 1885. The first mechanical' excavating machine used for the purpose was really a dredge minus the hull, which had been purchased from the Marion Steam Shovel Co. It was erected on a wood frame supported by wheels and was referred to as a dry-land dredge or stripping machine. Wood was used throughout in the construction of this primitive excavator, even for the boom which was 50 ft. long. A single-cylinder vertical steam engine furnished power to hoist the %-yd. dipper arid swing the boom. 400 cu. yd. of overburden moved in a day was a great record.

Jan 1, 1936

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By A. R. Farkoosh, J-P. Fortin, M. Pekguleryuz, S. Bagherpour

"Titanium aluminides are structural intermetallics which offer an attractive combination of high temperature strength and light weight. For such properties, these intermetallic alloys have become front-runners in replacing nickel-based superalloys used for several high temperature applications. These alloys are produced from metallic titanium, aluminum and master alloys involving an expensive and difficult process. A low cost alternative to current industrial production method is the new modified aluminothermic process which directly reduces titanium oxide (TiO2) to titanium aluminides. Nevertheless, this process has itself significant challenges in achieving alloys free of oxide inclusions; the close densities of the slag and the titanium aluminides makes slag/molten metal separation a challenging task. Usually, the alloy produced requires a second refining step. In this study, thermodynamic calculations based on CALPHAD method were performed to determine the solidification path and an attempt has been made to develop a criterion to increase the density deference between the slag and the alloy by alloying with appropriate elements. Furthermore, scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were utilized to examine the microstructure and phase selection of three Ti-Al alloys produced by the aluminothermic reaction, including the as-cast, refined in a controlled atmosphere and inert-gas-refined alloys. The composition range of the alloys studied was restricted to the a2-Ti3Al + ?-TiAl phase field (Ti-30Al) in the binary Ti-Al phase diagram leading to a lamellar structure with different complex intermetallics as shown in Figure 1.INTRODUCTIONTiAl based alloys are promising structural materials for high temperature aerospace and automotive applications. This is due to some attractive properties such as low density, high specific strength, high specific stiffness and high temperature strength retention (Wen-bin, Xue-wen, Hong-fei, & Yong-feng, 2011). These alloys have become leading candidates to replace Ni-based super alloys in gas turbine engines. Replacement of Ni-based super alloy parts with titanium aluminides is expected to reduce the structural weight of high performance gas turbine engines by as much as 20–30% (Kothari, Radhakrishnan, Sudarshan, & Wereley, 2012)."

Jan 1, 2016

By William Gleason

The Dulles Corridor Metrorail Project is a $3-billion project that will link Dulles International Airport with the downtown center of Washington D.C. by way of a single seat train ride. The project is mostly above ground, but it does include two short, yet complex, tunnels through the area of Tyson?s Corner. The project is being completed in two phases. The Dulles Transit Partners (DTP), led by Bechtel, was awarded the first phase, a $1.6-bil-lion phase that includes 17 km (11 miles) of track with five stations. At Tyson?s Corner, the project includes twin 730-m- (2,400-ft-) long, 6-m- (20-ft-) diameter tunnels. Bechtel is self-performing construction for the $1.6-billion design-build job. Gall Zeidler Consultants was hired by DTP as designer for the NATM tunnel portion of Phase 1, and Beton-und-Monierbau was hired as tunnel subcontractor. Tyson?s Corner is an affluent and congested area that sits 152 m (500 ft) above sea level. To get through the area, it was decided that tunnels would be the best option with the least amount of disturbance to the surrounding areas. However, with extremely shallow groundcover above some points as well as soft soil throughout, the tunnels are also the most complex aspect of Phase 1. About 213 m (700 ft) was constructed utilizing the cut-and-cover method. The remaining 518 m (1,700 ft) is being constructed using the New Austrian Tunneling Method, which integrates the principles of the behavior of rock and soil masses under load, and monitoring the performance of underground construction during construction. ?The tunnel only falls 2 m (7 ft) from one end to the other and we pass through two soil conditions, they are both soft ground,? said Dominic Cerulli, tunnel task manager for Bechtel. ?Soft ground is very tricky because you have to close the ring in a timely manner to minimize settlements at the surface. If you don?t close the ring quickly to achieve a round structure that?s good in compression, the tunnel could start necking and squatting and the ground above it will settle. We are under major roadways, so excessive settlement would be a bad thing.?

Jan 1, 2011

By Brian W. Mackenkzie, Jozef Lajzerowicz

This paper is intended to familiarize planners in the noncommunist world with the district planning approach used in eastern Europe for mining development. It deals generally with the basic nature of the district planning problem, the planning process for mining development and the state organization for the planning of mining districts. A number of applications of district planning techniques to both established and new eastern European mining districts are described.

Jan 1, 1971

By A. McMullen

"IntroductionTHE LOW-VOLATILE bituminous coals of the Brazeau field, Nordegg, Alberta, are soft and weak in structure. The seams contain .bands of inferior material, locally designated 'black jack', and thin bands of friable carbonaceous shale having no definite horizon but usually 'floating' in the seam. Because of the weakness• of the coal and the friable nature of the shale bands, run-of-mine coal usually contains a very high percentage of fines, as •Shown in the following table:SIZE WEIGHT. %Plus 1/2 in 25.61/2 – 1/4 in 13.31/4 - 1/8 in 14.6Minus 1/8 in 46.5The most convenient way of cleaning the fine coal would be by treating it in association with the coarse coal, so that no additional plant would be necessary. To a limited extent this is possible in certain types of equipment, notably the jig. A system of washing without pre-sizing is not •attractive, however, when dealing with the friable coal under consideration, which contains •a preponderant proportion of fines. At the new Brazeau washery, separation is made at 3/8-inch on •a Robins 'Vibrex' •screen, the coarse sizes being cleaned in •a standard pulsator-type jig. A feldspar jig is used to clean the minus 3/8-inch fraction."

Jan 1, 1954

By Wayne S. Smith, Erik James, Jose R. Gomez

"Soil mixed seepage cutoff walls are increasingly being used in levee and dam modification projects nationwide. An important aspect of their overall quality depends greatly on the language included in the specifications. Depending on the method (e.g. vertical axis auger mixing, cutter soil mixing, or trench mixing techniques) the specifications are a blend of prescriptive and performance based contract language with differences in element construction, element connections, quality control/quality assurance, and work area restrictions. Many of the existing specifications were initially developed by contractors in whole or in part, and can contain restrictive provisions favoring the authoring contractor. In response to these challenges, basic soil mixing fundamentals were revisited and recent lessons learned incorporated, resulting in the development of a new specification for soil mixed seepage cutoff walls that provides adaptability for the various construction methods. The new specification addresses quality control, quality assurance, equipment independence (elimination of restrictive contract language), rig instrumentation.INTRODUCTIONSoil mixing has been used in the construction of seepage barriers for over 30 years. Most soil mixed project primarily use the wet-rotary-shaft, wet-rotary-end or wet-vertical panel methods (reference FHWA Deem Mixing Manual Figure 137). One of the first major soil mixing seepage barriers was constructed in the Jackson Dam in Wyoming. Since then the use of soil mixing for seepage barriers has increased significantly and this specialized domain of construction which was solely procured by RFP methods, is now increasingly being specified in projects issued for bid. The Bid documents require more careful specification writing than RFP methods because the RFP methods allowed detailed proposals by the contractor. Therefore the development of soil mixing specifications began with contractors preparing the specifications. This paper addressed some of these issues, and proposes methods to address these resulting concerns. The resolution of these issues considers several aspects: 1) Assessment of binder injection, 2) Evaluation of mixing index, and 3) Verification testing."

Jan 1, 2016

By R. Fernando

"The National Institute for Occupational Safety and Health (NIOSH) National Personal Protective Technology Laboratory (NPPTL) is leading an effort to develop the next generation of self-escape breathing apparatus for egress from confined spaces in emergency scenarios. A backpack style closed-circuit mine escape respirator design was one configuration explored as part of the research imperative directed by the 2006 MINER Act. Stakeholder feedback from MSHA and at the NIOSH Breathing Air Supply Partnership Meeting indicated a smaller belt worn unit that does not sacrifice performance is desirable. This paper outlines some further technology advancements that may be investigated toward developing such a small-sized respirator. Technologies being considered are novel chemicals for improved carbon dioxide (CO2) absorption and oxygen (O2) production, eliminating a dedicated CO2 scrubber by incorporating its function in the spaces of the respirator’s breathing loop and storing O2 in a liquid form with long standby capabilities. When these technologies are applied to a future design, there is the possibility of having an escape respirator that can be belt worn and capable of being certified to 42 Code of Federal Regulations (CFR) Part 84 standards, including sub-part O for escape purposes including mine escape. BACKGROUND NIOSH NPPTL has a Research and Development effort to provide mine workers with state-of-the-art breathing air technologies to comprehensively support initial and continued self-escape, refuge alternatives, and rescue needs, resulting from mine emergencies. As part of this R&D effort, NIOSH invested in the development of a next-generation closed-circuit mine escape respirator (CCMER) which would be compliant with NIOSH’s respirator standard requirements, 42 Code of Federal Regulations Part 84, including sub-part O. The design features of the CCMER also address the MINER Act’s requirements for transitioning between devices without the need for doffing the initially donned device. It would also allow for improved protection when using voice communications with a donned device ."

Jan 1, 2018