Search Documents

By E. Oshima

The only one reverberatory furnace smelting in Japan has been alive in Onahama Smelter, Onahama Smelting and Refining Company. The fuel for the reverberatory furnaces had been changed from bunker C-oil to mainly coal and partially waste tires to reduce the energy cost. The steam, recovered by the waste heat boilers of the reverberatory furnaces, has been utilized fully for the power generation to save the purchase power. Copper concentrate has been smelted also by injection through tuyeres in the P.S. converters since 1983. The amount of concentrate, treated in the converters, was increased by the construction of small oxygen plant in December, 1990. In the paper, the current practice and improvements in the reverberatory and converter operations are described.

Jan 1, 1993

The captions to Figs. 1 and 2 of the paper by B. J. Parry entitled 'High-strength cold-rolled steels' should read as follows:

Jan 1, 1984

By D E. G Connelly, K Y. Wong

Gold at the Harbour Lights Mine (HLM), WA occurs principally in pyrite (Py) and arsenopyrite (AsPy) minerals rendering it inaccessible to direct cyanidation. Froth flotation produces a concentrate with low mass recovery and with high recoveries of sulfides. After investigating several alternatives, a novel flotation process has been developed to separate the concentrate into pyrite and arsenopyrite rich fractions. The pyrite fraction is finely ground and cyanide leached, while the arsenopyrite is treated off-site. This paper describes the separation process from laboratory bench scale through to commercial operation at the HLM gold plant.

Jan 1, 2005

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By Jorge Luiz Soares do Couto

O presente trabalho tem como objetivo realizar uma análise comparativa do comportamento de quatro metais de solda obtidos pelo processo arame tubular de forma a avaliar o efeito da relação Ni-Mn nas propriedades mecânicas. Foram soldadas juntas multipasse, com consumíveis da classe 110ksi de resistência mecânica, preaquecimento de 200°C, corrente contínua e posição plana e aporte térmico nominal de 1,2 kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados integralmente do metal depositado, na condição de como soldado e após tratamento térmico pós-soldagem. Os resultados mostraram que as melhores propriedades mecânicas foram obtidas para uma composição contendo 1,35%Mn e 2,50%Ni. Adicionalmente, verificou-se que o tratamento térmico pós-soldagem propiciou uma redução da tenacidade ao impacto dos metais de solda de maior resistência devido à precipitação de carbetos nos contornos de grão.

Aug 7, 2018

By D Osborne

Current mineral extraction and valorisation activities still have a strong focus on the ‘delivered product(s)’ which might be a bulk commodity such as metallurgical coal, hematite, bauxite, etc., and mineral concentrates such as metal sulphides, oxides, and carbonates; precious metals, such as gold, silver and PGMs, REEs or battery metals; halogen salt forming elements; or industrial minerals, which are non-metals including crushed rock, sand, and gravel etc. With the current focus on tailings disposal the pushback has been to seek alternatives to the currently ‘conventional’ disposal method via increasingly higher risk tailings settling facilities (TSFs) with a changing focus towards ‘dry disposal’. Whichever option is selected, the alarming trend is the increasing cost and ESG impacts. An emerging approach is to pose a focusing question ‘Is there anything else passing into the tailings stream and/or disposable waste streams which could be recovered and pass into the product revenue stream? All of the above ‘primary’ process streams offer opportunities for increasing recovery and offsetting some of the disposal costs. Some secondary opportunities are already being pursued, such as REEs and battery metals from base metals deposits, but other opportunities are still being overlooked, such as building materials and soil conditioning pellets. These potential ‘new’ product streams can also utilise other mining and domestic wastes such as smelting slags, glass waste, plastic waste etc. This paper will address these opportunities and provide examples including process approach, economics and some of the current barriers that exist, which are holding back progress on such initiatives.

Sep 1, 2024

By S Sullivan

The key skills for a competent geologist are observation, documentation, analytical thought and the ability to communicate. These attributes have served the geological world for the past two centuries since the field of geology was separated out from natural philosophy. The understanding of the structural setting, lithologies, alteration and 3D distribution of the target mineral species are essential precursors to resource evaluation and potential economic extraction. The advent of artificial intelligence and machine learning has matured to the point where observation by dedicated sensors and analysis by customised AI algorithms can replace manual processes and deliver credible results. In combination with analytical data such as assays, various sensors now collect physical properties of rocks which are used as proxies for mineral identification and rock mass classification. These sensors include X-ray and infra-red spectra, magnetic susceptibility, gravity/density, EH/pH measurements, conductivity, colourimetric readings, porosity, fracturing and fracture intensity. Analysis using machine learning techniques trained using known data sets can determine rock type classification, rock density, quantification of grade/quality attributes, mineral alteration, weathering and geotechnical attributes such as rock quality. This type of data relies on calibration and quality control of a variety of different types of electronic hardware. The resulting data is non-additive, has error ranges and will be suitable for consumption by fast AI methods providing probabilistic analysis. A second stage could include geometallurgical constraints to provide an ‘extractability index’, which is of more interest to miners than pure geotyping. Using resultant interpreted geological criteria, 3D domain models with spatial attributes will be built.

Sep 1, 2024

By A. L. Peyton

The Brewer mine, near Jefferson, Chesterfield County, S. C., was originally operated as a gold mine. As late as 1890 this mine was reported to have been one of the large gold producers in the southeast. Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered, by Parks3/ and Parks of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.

Jan 1, 1953

By Adolfo Pillihuaman Zambrano

Fe-Cr-C production is a very high electrical energy consuming process. Decrease up to 10% of this electrical energy is expected when self-reducing agglomerates are used. This research aims to understand how the synergetic effects are when stronger reductant, like Fe-Si, is substituted for coke in self reducing pellets. Brazilian chromites containing 41.2%Cr2O3 were mixed with petroleum coke and agglomerated with cement as the binder. Small amounts of 1%, 2% and 4% of Fe-75%Si were substituted for the equivalent petroleum coke, and pure silica plus hydrated lime were added for adjusting the slag composition. The mixture was pelletized, dried and submitted at 1773K up to complete the reactions. The results showed that the reduction reactions were 1.4 and 2 times faster with 1% and 2%Fe-Si addition, respectively, than with no addition. The microscopic analysis showed that it was formed a liquid phase, but the pellet did not collapse what indicates that the coalescence of the metallic phase depends on the dissolution of the pre-reduced particles of the chromites into slag.

Jan 1, 2008

By May Nyman

Due to the vast diversity of chemical media in which metal separations are executed, a wide range of ion separation materials are employed, This ,results in an ongoing effort to discover new phases with novel ion exchange properties. We present here the synthesis of a novel class at, thermally and chemically stable microporous, niobate-based materials. Ion exchange studies show these new phases are highly selective for Sr2+ and other bivalent metals.

Jan 1, 1999

By Bruno Deves Flores

O presente estudo visou avaliar em escala laboratorial os efeitos da substituição de carvão importado por nacional em misturas típicas para fabricação de coque metalúrgico. Carvão da camada Barro Branco foi amostrado, beneficiado e caracterizado. Misturas entre carvões coqueificáveis importados, coque de petróleo e o carvão brasileiro foram produzidas de modo a permitir a avaliação da influência do carvão nacional na qualidade do coque. O coque gerado no estudo foi produzido em escala de laboratório e posteriormente avaliado a partir de testes de resistência mecânica e reatividade. Os resultados do estudo apontam que a substituição parcial de carvão importado por nacional é viável tecnicamente sem que ocorram prejuízos importantes à qualidade do coque gerado. As diferenças de qualidade dos coques produzidos com ou sem carvão nacional foram menores para misturas com alto teor de inertes, onde as características termoplásticas da mistura passam a controlar a qualidade do coque gerado.

Oct 30, 2017

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By J. W. Griffith, J. L. Stauffer, L. M. Demers, D. C. Kuhn, S. Riliog

"The relative activation of eicosanoid production which results from the exposure of the alveolar macrophage (AM) to mineral dusts is thought to be a key factor in the pathophysiology of occupational lung disease. We compared in vitro basal and silicastimulated production of prostaglandin E2 (PGE2) and thromboxane A2 (TXA2) by AM from normal humans and non-human primates (Macaca nemistrina). In addition, we instilled mineral dusts directly into one lung of the non-human primate and evaluated AM eicosanoid production at two week intervals following dust instillation. Unstimulated AM from humans produce more PGE2 and TXA2 than do AM from M. nemistrina. However, in vitro exposure of AM from both species to silica dust produced a qualitatively similar increase in TXA2 production accompanied by no change in PGE2 production. Sequential analysis of AM eicosanoid production following a single bolus exposure to bituminous or anthracite coal dusts, titanium dioxide (Ti()i) dust or crystalline silica showed marked variability among individual non-human primates in qualitative and quantitative aspects of dust-induced eicosanoid production. However, the rank order of potency of the different dusts (silica> anthracite> bituminous) correlated with epidemiological evidence relating the type of dust mined to the incidence of pneumoconiosis. These studies suggest that the non-human primate may serve as a model for the study of both the role of eicosanoids in the etiology of dust-induced occupational lung disease and the biochemical basis for individual variability in the response of lung cells to mineral dust exposure. IntroductionOccupational inhalation of mineral dust can lead to chronic debilitating lung disease ( 1,2). One of the key components of the disease process is thought to be the interaction of mineral dust with the alveolar macrophage (AM) and the subsequent release by the AM of inflammatory and fibrotic substances (3,4). Chronic inhalation of mineral dust, depending on the type and amount of dust, may then produce a situation in which ongoing inflammation, accompanied by the destruction of functional lung tissue by products of activated AM and polymorphonuclear neutrophils, stimulates the production of nonfunctional matrix by lung fibroblasts.The AM produces several oxygenated derivatives of arachidonic acid (AA) which may play important roles in dust-induced lung pathophysiology (5,6). In previous studies in the rat, we found that prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (L TB4) were the major AA metabolites produced by AM (7). PGE2 is associated with pro-inflammatory activity (8) as well as anti-fibrotic activity since it downregulates interleukin -1 (IL-1) and tumor necrosis factor (TNF) release by AM (9-11). TXA2 is known to stimulate platelet activity, cause bronchial and vascular smooth muscle contraction (12) and to possess chemotactic activity (13). LTB4 is chemotactic for neutrophils and monocytes (14) and has been suggested as an additional regulatory factor in the release of TNF by AM exposed to silica dust ( 15)."

Nov 1, 1995

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By Leonardo Martins da Silva

O minério de ferro quando encontrado contendo teores do elemento fósforo acima de 0,05% é considerado rejeito dada sua inutilização para o processamento de fabricação do aço. Tal fato ocorre devido a elevação da dureza do aço tornando-o quebradiço e com fratura. Sendo assim o presente trabalho tem como objetivo a avaliação do efeito do processo de lixiviação ácida como finalidade de redução do teor de fósforo no minério de ferro. Através da utilização do software Termocalc® foi possível analisar as diferentes estruturas formadas em diferentes teores do elemento fósforo. Através da técnica de microscopia eletrônica de varredura (MEV) foi possível analisar a estrutura do minério de ferro após seu tratamento com a energia de micro-ondas. Por meio da técnica de planejamento estatístico fatorial com pontos centrais e axiais foi possível determinar as condições ótimas de remoção de fósforo através da técnica de lixiviação ácida.

Aug 1, 2018

By E. C. W. Perryman

BEFORE describing the methods used for fabricating uranium into various shapes and sizes it is necessary to illustrate briefly the unusual conditions under which uranium has to operate when used as a fuel element in a reactor. During reactor operation, for every fission that occurs two atoms of intensely radioactive fission products are produced together with two or three neutrons. The neutrons that are ejected possess several m.e.v. of energy and when one of them strikes an atomic nucleus, that atom acquires up to 105 e.v. of kinetic energy. This is large enough to displace the atom from its lattice position and send it shooting through the crystal, displacing other atoms out of their lattice positions. The net result is that a large number of vacancies and interstitial atoms are formed within the crystal lattice which sometimes have profound effects on the physical and mechanical properties of the material in question.

Jan 1, 1957

By Edward C. Stephens, Robert R. Coats

High-grade copper ore was discovered in 1932 in the long-dormant Mountain City (Cope) mining district, Elko County, Nevada. From 1932 to 1947, the one producing mine in the district, the Mountain City Copper Mine, produced 1,109,878 short dry tons of ore averaging 9.745 per cent copper, 0.274 ounces of silver, and 0.0057 ounces of gold per ton. The Mountain City Copper Mine is developed in eugeosynclinal rocks of Ordovician age, the Valmy Formation, which is part of the upper plate of the Roberts Mountains thrust. On the Valmy were deposited unconformably first, a elastic formation of Devonian or Mississippian age, the Grossman Formation, succeeded unconformably by a ·sequence of three conformable formations, the Banner, the Nelson, and the Mountain City. The Banner Formation probably is early Late Mississippian in age; the ages of the Nelson and Mountain City are not known precisely but are believed to be of Late Mississippian and Carboniferous(?) age, respectively. A thick formation of elastic rocks, limestone, and volcanics, the Reservation Hill Formation, has been thrust over the Mountain City. The age of the Reservation Hill is unknown but is presumed to be Pennsylvanian(?) and Permian(?). Several plutons of Cretaceous quartz monzonite intrude the Paleozoic formations; they and the intruded formations have been laid bare by erosion, and several sequences of volcanic rocks of Miocene and Pliocene age, and perhaps in part older, have been successively deposited on irregular erosion surfaces. The primary mineralization of the Mountain City Copper Mine is believed to postdate the deposition of the Nelson Formation and to predate the intrusion of the quartz monzonite. The primary ore bodies are lenticular in shape and are composed largely of quartz, pyrite, and chalcopyrite. The ore lenses, in general, strike northwestward and dip northward. They occur in the Valmy Formation within a definite stratigraphic sequence composed largely of shales with associated minor quartzite lenses. The ore is epigenetic. The principal ore body, the "200," was completely leached to the 200 level. Abruptly beneath the barren gossan was supergene copper sulfide ore, much of which assayed 50 per cent copper. The secondary copper minerals are sooty and massive chalcocite, bornite, and covellite. The supergene enrichment of the ore may have required a large part of Tertiary time.

Jan 1, 1968

By Gene Baker

A new Safety Library Publication (SLP), SLP-27, which is titled “Security in Manufacturing, Transportation, Storage and Use of Commercial Explosives” was recently released by the Institute of Makers of Explosives (IME). SLP-27 makes recommendations for both general security and enhanced security at explosives sites when security risk levels, declared by the Department of Homeland Security (DHS) using its Advisory System, have temporarily increased.

Jan 1, 2006

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By Francesco Chiappalone, Miriam Piemontese, Lance Waddel, Paolo Perazzelli, Emidio Tamburri, Roberto Schuerch

The Three Rivers Protection & Overflow Reduction Tunnel is part of the Long-Term Control Plan of the City of Fort Wayne, Indiana (USA). The 4.9 m internal diameter tunnel, of length approximately 7.5 km, is excavated at a depth of approximately 40–60 m through carbonate rocks using a slurry TBM. Due to the high hydraulic conductivity of the rock mass and the high in-situ ground water pressure (up to 6.5 bar), the management of the water inflow during the TBM advance and standstills, represents the major challenge for the project. This paper outlines the geotechnical conditions and the hazards related to the large water inflows expected in the pre-excavation phase and discusses the experience gained during the construction of the first 8,224 feet (2,507 m), (first third of the total length of the tunnel).

Jun 13, 2021