Search Documents

By Doris M. Hyde

The 350,000-barrel-per-day Bahamas Oil Refining Co remained closed throughout 1986. Financially troubled Charter Oil Co., joint owner of the refinery with Chevron Oil Bahamas Ltd., agreed in principle to have Chevron assume full ownership in return for canceling debts owed Chevron. Finalization of the agreement was pending at yearend. Burmah Oil Ltd. took more than a $30 million loss on the sale of its interest in South Riding Point Grand Bahama Transshipment Terminal to South Riding Point Terminal Holding Ltd.

Jan 1, 1988

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclone separators are used in various industrial applications, including mining milling and tailings systems, in order to separate or classify solid particles and liquid droplets from multiphase systems. The flow within a hydrocyclone commonly used in the mineral processing industry was investigated numerically and experimentally using Particle Image Velocimetry (PIV) and refractive index matching techniques. The computational simulations were performed using a commercially available CFD package, STAR CCM+. Two turbulence models were used in the numerical calculations: the k-? model and the Reynolds Stress Model (RSM). In both cases, the first order discretization scheme was unable to resolve the flow characteristics accurately due to the high levels of numerical dissipation. PIV measurements were taken at various spatial locations along the cyclone. Both the numerical simulations and PIV data demonstrate that tangential velocities tend to increase when going radially inward from the cyclone wall towards the vortex finder, and reach a maximum value before they begin to decline rapidly and eventually become zero at the wall. The results also demonstrate the utility of non-axisymmetric approaches in cyclone flow simulations for a greater understanding of the fluid mechanics. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. The comparisons demonstrated good agreement between the two models.IntroductionHydrocyclones are devices used to separate and classify solid particles or liquid droplets from liquid-solid or liquid-liquid systems. Versatile in application, they have been widely used in many industrial applications including the food, oil, power generation, chemical and mineral processing industries since 1891, when the first hydrocyclone was introduced by Bretney (Park, 2003). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2016

THE Taranaki oil-field is situated on the western side of the North Island of New Zealand, at about its widest part, and may be said to be the most compact and fertile part of the Dominion, for, with the exception of the upper half of Mount Egmont and of the ranges adjoining, which absorb 36,000 acres, the whole of the area, minus what is taken up by the rivers and streams is suitable for settlement, and certainly two-thirds is good land. The gross area of the district is 2,417,299 acres. The principle rivers are the Wanganui, Mokau, Waitara, Patea and Waiwakaiho. Mount Egmont, which is 8260 ft. high, used to be called Taranaki, and from it the district takes its name (the Maori meaning of which is "sloping peak ").THE OIL-FIELDThe discription of an oil-field now-a-days usually resolves itself into a mass of figures and statistics, of great interest and value to the engineer and commercial man, but practically indigestible to the general public. It is the realm of the financierand the captain of industry.

Jan 1, 1912

By Renpei Yoda

An investigation was conducted to develop columbium alloys with e1evated-temperature strengths higher than those exhibited by more common commercial columbium alloys, and attention was given to improving the oxidation resistance and ease of fabrication. Additions of carbon, aluminum, and chromium were made to some columbium-base alloys, and their effects on workability, recrystallization, oxidation resistance, and mechanical properties at elevated temperatures were explored. The additions were made to take advantage of (1) solid solution strengthening, and (2) precipitation hardening. Three alloys displayed good high-temperature properties with relatively good oxidation resistance at 1,000° C, and tensile strengths from 26,000 to 32,200 psi at 1,400° C. When the properties of these alloys were compared with those of commercial alloys, B-66 and FS-85 (1),4 the outcome was favor-able for the alloys studied in this investigation.

Jan 1, 1967

By M K. de Brodtkorb

Late Cenozoic ore deposits æPrecious and base metal-richÆ and æSn-Ag-polymetallicÆ ofNorthern Puna are associated either with Middle Miocene dacitic volcanic-dome complexes or with Upper Miocene dacitic-andesitic volcanic centres.   Ore mineralogies and their related volcanism are discussed. A strong link is observed between the Cenozoic Metallogenetic Province of Northern Puna and the Southern Bolivia Tin and polymetallic provinces.  

Jan 1, 1995

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By Wylie A. W, Mathew PJ

Bulk density and grade were determined on a variety of ore samples from the Mount Tom Price iron ore mine and the interrelationship between these properties and porosity deduced.Variable porosity is responsible for the wide scatter of data points and low accuracy of prediction in the grade of a single sample from grade/bulk density relationships.However, with a sufficient number of such data points, as from a nuclear geophysical borehole logging operation, the mean ore grade in an exploration-type drill hole (~63 per cent Fe) could be determined by regressionanal~sis with 95 per cent confidence intervals of approximately ± 1 per cent Fe. From the same logging operation, utilizing core data for calibration of the probe, the -mean fractional porosity for the drill hole (0·19 ± 0·016 at 95 per cent confidence interval) was deduced. This is less accurate than the corresponding result obtained on core material in the laboratory (0·20 ± 0·005).The range of porosity was from 0·08 for dense, high grade sectIOns of the ore, to 0·28 for friable ore of high grade or goethitic ore of lower grade. Shale band porosity ranged from 0·15 to anomalously high values of 0·48 believed to be caused by leaching of iron minerals from the shale. Porosity values for the iron ore component of the deposit are comparable to those found for the Cockatoo Island (W.A.) mine, and for sections of the Krivoy Rog (Ukraine) iron ore deposit of the Soviet Union.

Jan 1, 1978

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017

By R. B. Krog

The use of belt air as an intake source at longwall operations has changed greatly over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors, including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different than for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with the belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2010

By Don Deardorff, Ke Yang, Yingcai Han, Ken Sorensen, Robert Kruger, Mark Petersen, Diane Fiorelli, Larry Goldfarb, Kathryn Petek, Kwabena Ofori-Awuah

Design of deep foundations for lateral loads requires an understanding of soil-foundation-structure response during loading. Lateral loads on a deep foundation (piles) could be due to earthquakes, winds, waves, and/or machine vibrations. Over the years, analysis of response of piles due to lateral loads evolved from closed-form solutions to p-y methods to strain wedge to finite element/finite difference modeling. Although analysis of lateral response of piles and shafts is routinely performed, there is no single guidance document and/or standard for design and testing. Several different analytical methods are available for the analysis, and the resulting design can result in significantly different responses which can create confusion. This is especially true for analyzing and designing piles in potentially liquefiable soils with lateral spread issues under seismic conditions.This guidance document is intended to assist geotechnical engineers, pile designers, and contractors in analysis, design, and testing of piles and drilled shafts for lateral loads. This document discusses the background of different analytical and testing procedures and presents the recommended methods for analysis, design and testing of piles for lateral loads.Chapter 1 defines the different kinds of lateral loads to which a single pile or pile group may be subjected. This first chapter also presents different types of piles used to resist lateral loads.Chapter 2 discusses geotechnical issues related to lateral pile design such as liquefaction and lateral spreading and other non-seismic issues. Also addressed in Chapter 2 is geotechnical site characterization (as related to lateral loads) in terms of site investigation, in-situ testing, geophysical testing, laboratory testing, and estimation of soil/rock properties.Chapter 3 discusses the background and available analytical methods and tools for the analysis and design of single piles and drilled shafts. Several methods of analyses from closed-form elastic solutions to the finite element/finite difference solutions and their applicability are discussed. Available commercial computer software packages for analyzing single piles and drilled shafts are also presented.Chapter 4 expands the discussion of single piles and drilled shafts into the analysis and design of pile groups. In addition, group effects, resistance of pile caps, results of previous experimental and analytical studies, and available analysis tools and software for pile groups are discussed.Chapter 5 presents the issue of lateral resistance of piles and drilled shafts as discussed in different national and international building and non-building codes. A summary of extensive research on several codes are presented to facilitate the compliance with different codes.Chapter 6 discusses structural design issues of individual piles and drilled shafts such as depth of fixity.Chapter 7 discusses soil structure interaction issues related to kinematic and inertial effects due to seismic loading and available methods of analyses.Chapter 8 discusses and presents the typical procedures for the lateral load testing of piles. This guideline was developed as an aid to the practicing engineer in providing information, direction and commentary on the lateral design of deep foundations. Although all reasonable effort has been made to accurately compile the material and information contained herein, no warranty is made with regard to any such material or information and the Deep Foundation Institute assumes no responsibility for any possible errors or any direct or indirect result of the use of any such material or information. It is not intended that this document address every factor affecting lateral design for every situation. Therefore it is the responsibility of the person utilizing information from this document to confirm that it is appropriate and correct for their situation as well as to understand and properly apply

Jan 1, 2012

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

IN the irregularly shaped ore-bodies of the North Mount Lyell mine by overhead stoping, the method of filling the is a special feature.The situation of the mine two miles from the smelter and mill at an devation of 1000 ft. above the latter, precluded the economical use of granulated furnace or the mill tailings, even if these materials were as suitable for the purpose as the rock nowquarried at North Lyell methods at Mount Lyell have already been described in Proceedings of the Institute.*The breaking the ore in large dome-shaped stopes is still the rule, but the slope or "rill" is much flatter now than formerly. Owing the greater fluidity of the filling now in use, it is sometimes necessary to resort to square-sets, both at the ground floor and above, the roofs and walls are generally enough to permit stoping without timber, except for ground and occasional stacks on the rills.Sufficient area of ground floor has been beaten out to start overhead stoping, the dome back is partly formed, with its apex a rise which connects with the mullock-pass reticulation.(Sce 1 showing this reticulation in diagrammatic form.)

Jan 1, 1927

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By D. Yuan, M. Sitter, S. St. Jean, M. Collins

The Ambatovy Joint Venture comprises an operating lateritic nickel mine, ore slurry pipeline, pressure acid leach plant and nickel refinery in Madagascar. The hydrometallurgical process selected by Sherritt for treatment of the Ambatovy ore is a long-term, sustainable approach to producing nickel. Sulphur, used to prepare hydrogen sulphide, which is used to produce mixed sulphide intermediate, is recovered in the refinery as ammonium sulphate fertilizer. Additional sulphur is used to generate sulphuric acid for treatment of the ore in the high pressure acid leach (HPAL) step; fossil fuel consumption is minimized by using the heat generated from the exothermic reaction between sulphur and oxygen in the acid plant to produce power and steam. Steam consumption is minimized by design of efficient flashing and preheat systems for HPAL, while the high temperature of the HPAL step serves to minimize acid consumption. Fossil fuel consumption by the operation as a whole is further minimized by locating the leach plant and refinery near the port of Toamasina and utilizing a 220 km slurry pipeline to transport ore from the mine to the leach plant. In addition, Ambatovy has demonstrated a strong commitment to sustainability programs such as the biodiversity management program at the mine and local procurement in Madagascar. In this paper, the hydrometallurgical process for nickel and cobalt recovery from Ambatovy ore is described, along with highlights of Ambatovy’s approach to sustainability in Madagascar.

Jan 1, 2015

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By N. S. Dalal, J. F. Mega, X. Shi, V. Vallyathan

Several studies have suggested that pulmonary toxicity to asbestos and silica may be mediated through oxidant-induced cell injury. We have reported recently that surface radicals associated with freshly fractured silica may be an imponant factor in cell injury and induction of pulmonary disease. Although the generation of oxygenated radicals in dust-cell interactions has been demonstrated, there are no data correlating the toxicity of a dust with the level of oxygen radical generation by the dust during its interaction with phagocytic cells. In the present study, we have investigated the in vitro generation of oxygen free radicals from human neutrophils and rat alveolar macrophages stimulated with freshly fractured silica, aged silica, amosite, crocidolite, chrysotilc, and a nontoxic dust, barite. Electron spin resonance (ESR) with the aid of a spin trap phenyl-N-ten-butyl nitronc (PBN) was used to measure the oxygen radicals generated during phagocytosis of the dusts. The relative toxicity index and ESR peak heights, on an equal surface area basis and normalized to barite as one, showed a direct relationship. The normalized toxicity indices and peak heights were: silica, 3.5 versus 2; chrysotile, 4 versus 2; crocidolite, 11 versus 8; and amosite, 26 versus 13. Addition of hydroxyl radical scavengers such as catalase, dimethyl sulfoxide, 1,3 dimethyl-2-thiourea (DMTU), sodium benzoate, and mannitol prevented the radical generation. Carmustine, a glutathione reductase- glutathione peroxidase inhibitor, caused a 5-fold increase in the radical generation. These results indicate that a nontoxic dust such as barite generates toxic oxygen radicals at a minimal level that can be quenched by the normal cellular defense system. For toxic dusts such as silica, amositc, chrysotile, and crocidolite, the potential for oxygen radical generation is enhanced by their surface propenies, physical dimensions, and the surface-based radical-generating redox sites. The enhanced radical generation may impair the cellular defense system, resulting in cell injury. Use of scavengers, chelators, and potentiating agents suggests the membrane-based oxidase system as the probable primary source of the radical-generating system. The data presented herein suggest the generation of oxygen free radicals as an important primary event in silica- as well as asbestos-induced cell injury.

Mar 1, 1992

By Wolfgang Gütter

India is targeting to boost its electrical capacity from 100 GW to 200 GW within the next 10 years. The National Hydroelectric Power Corporation (NHPC) has decided in2001 to take execution of the 800 MW Stage-II of the prestigious 2,051 MW Parbatihydrol electric project in Kulu district of the northern province Himachal Pradesh. Two parallel 30° inclined underground pressure shafts of 1.542m in length each will be excavated in different geological formations and lined with hexagonal concrete segments by a hard rock double shield TBM. That kind of heading will be a novelty to India and an innovative method for inclined pressure shafts. The 4.88m Mitsubishi DSTBM will be assembled underground on a swivelling steel platform especially designed for the launching as well as for the acceptance of the TBM in the upper cavern of each shaft. The hexagonal segmental lining system causes a significant higher job safety than an open TBM with conventional support. Each ring consists of four honeycomb segments with 20 cm thickness. After finalisation of the excavation a steel liner will be installed and concreted. The Joint Venture Jäger-Seli will perform the two pressure shafts as a sub-contractor for the Indian company Gammon India Ltd.

Jan 1, 2005