Search Documents

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By F Hancock

A rainfall simulator was developed to assist with hydrogeomorphic research into the stability of engineered landforms associated with rehabilitated uranium mines in the Top End of Australia. It can be used in rough terrain with slope gradients up to 30o. The rainfall simulator is modular, utilises upward jetting nozzles, has a multiple head arrangement and is capable of delivering rainfall intensities between 60 and 300 mmh-1 over areas up to 1000 m2 and could be easily modified for larger areas. Rainfall uniformity is commonly in excess of 80 per cent and the kinetic energy approaches that of natural rainfall (The modular design utilises an equilateral triangular array of rainfall stands, constructed from galvanised steel water pipes and flexible plastic hoses. Total construction costs are low. The water supply reservoir is mobile and easily constructed. An example of its use at Ranger Uranium Mine, investigating the effect of cover on rainsplash and rainwash dominated processes shows that vegetation cover is likely to reduce the erosion rate by these processes by at least four times below that experienced on bare areas.

Jan 1, 1997

By T. Celik, B. Genc, C. Musingwini

"Mine planning software continues to be an important factor when it comes to the development of the South African mining industry. To contribute to this development, a new methodology to define and measure mine planning software utilization in the South African coal mining sector within an evolving data-set framework was developed. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgy in 2013. In 2014 the data-set was updated with additional and new information.In this paper, using the 2012 and 2014 time-stamps, a methodology for estimating the software utilization is developed. In this methodology, three variables: commodity, functionality, and time factor are used to define and measure the software utilization in order to ultimately inform decision making strategies for software utilization. Utilization in the coal sector was measured according to six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation and Optimization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and wanting to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2016

Certain information contained herein regarding Champion Minerals Inc., including management?s assessment of future plans and operations, may constitute forward-looking statements under applicable securities law and necessarily involve risks, including but not limited to risks associated with mining exploration, operating costs, production costs, volatility of share prices, currency fluctuations, imprecision of resource and reserve estimates, environmental risks and ability to access sufficient capital from internal and external sources. As a consequence, actual results may differ materially from those anticipated in any forward looking statements. Plans, intentions or expectations disclosed in any forward-looking statements or information should not be read as guarantees of future results or events, and will not necessarily be accurate indications of whether or when or by which such results or events will be achieved. Except as required by law, Champion Minerals Inc., expressly disclaims any intention and undertakes no obligation to update any forward looking statements or information as conditions change. The historical mineral resources mentioned are strictly historical in nature and are non-compliant to National Instrument 43-101 mineral resources and mineral reserves standards, and should therefore not be relied upon. A qualified person has not done sufficient work to upgrade or classify the historical mineral resources as current National Instrument NI-43-101 compliant.

May 1, 2011

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By W. J. Spat

Political risk is an integral part of the mining business in northern Andean countries. Peru, Ecuador, Colombia and Venezuela all have a higher than average political risk compared with other South American countries. Successful operations require good political-risk information, a thorough political-risk-management plan and a strategy to deal with political-risk perception on the part of the investing public. Colombia is perceived as about the riskiest place in the world to do business. A selection of recent headlines reads: “Colombia on the brink” (Economist, 1998), “Colombia’s ship of state is sinking” (Insight on the News, 1998), or simply “Bad news” (US Catholic, 1998). The World’s Most Dangerous Places rates Colombia as “currently the most dangerous place in the Western Hemisphere, and perhaps the world” (Aral and Pelton,1998). And many prospective investors and analysts say to Greystar Resources: “Yes, we love your results, but Colombia?”

Jan 1, 2000

By Thomas R. Larson

"Many concentrators use re-circulating “plant” water for dilution in their flotation circuits. However, if crusher dust suppressants, ball mill grinding aids, or even agitator bearing grease are introduced into this water, and the water itself is not subject to cleaning steps, then sufficient quantities of these chemicals may appear in the flotation cells and begin to impact the flotation separation. A bench flotation procedure has been coupled with statistical analysis in order to estimate the impact of small quantities of non-flotation chemicals on flotation performance.INTRODUCTIONCleveland Cliffs produces iron oxide pellets for blast furnace feed, and is developing the capability to produce ferrous metallic products to supply a wider customer base. Cliffs manages five North American iron mines, including the Wabush mine sites in Labrador and Quebec. Based on various characteristics of the ore bodies, the flow sheets of the five mines are diverse. For example, Hibbing Taconite uses magnetic separation alone as their primary upgrading method, but Northshore and Empire use magnetic separation followed by flotation, and Tilden uses flotation alone. Last but not least, the Wabush concentrator upgrades primarily with gravity and electrostatic separation techniques.At Northshore, concentrate from the magnetic separator circuit is fed to a reverse flotation circuit. By design, the magnetic separators operate at the highest possible recovery of magnetite, as the separator tails are discarded, and relatively high silica content was acceptable to Northshore’s customers. As the steel-making industry moved toward lower and lower slag volumes, the silica content in the magnetic separator concentrate became a problem. The flotation step was added in the late 1980s in order to decrease the silica assay of the magnetic separator concentrate to meet the current customer requirements. In this setting, the flotation feed stream contains very little silica that occurs as liberated quartz particles. As the degree of liberation of the flotation feed stream is then a limiting factor for silica removal, the online grind control then was linked to flotation in the overall plant control system so that grind can be adjusted to achieve improved liberation if necessary for the flotation process."

Jan 1, 2002

By Jerome P. Downey

In the thermal treatment of electric arc furnace (EAF) dusts, zinc is reduced, volatilized, and ultimately recovered either as liquid metal in a splash condenser or as solid zinc oxide in bag filters. During the process, the duet's chlorine and fluorine content also enters the gas phase and condenses as dross in the splash condenser or as salts which contaminate the zinc oxide product. Pretreatment of EAF dust by pyrohydrolysis appeared to offer a means of minimizing the duet's halogen content. The primary research objectives were to experimentally verify the technical viability of pyrohydrolysis and delineate the process parameters requisite for efficient halogen removal. To this end, representative EAF duet samples were secured and characterized by x-ray diffraction, scanning electron microscopy, and Mössbauer analyses. Specific- experimentation focused on the response of halogen extraction to variations in temperature, retention time, water vapor partial pressure, and various additives. The experimental results proved that 97 to 99 percent chlorine extraction and 80 to 85 percent fluorine extraction are consistently achieved when EAF dusts are blended with silica and roasted at temperatures of 850°C or greater in a furnace atmosphere of 75% steam (diluted by air). A statistical analysis further established that more than- a single optimal point exists, thus affording flexibility in parameter selection (e.g., by increasing temperature, the necessary retention time and additive concentrations are decreased). The findings substantiate the feasibility of pyrohydrolysis roasting in reducing the chlorine and fluorine in the EAF dust to a level that will obviate industrial concerns about halogen contamination. The end-product of the pyrohydrolysis procedure is a de-halogenated, self-fluxing calcine which can be directly charged to a plasma or flame reactor. The paper includes design parameters and flow diagrams illustrating the pyrohydrolysis process integrated with the plasma and flame reactor technologies.

Jan 1, 1992

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By T P. Fischer, S N. Williams, N C. Sturchio

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these 'primary' components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

By Levent Ozdemir

The results of a laboratory research program aimed at the development of a water jet assisted drag bit cutting system for coal mine applications are presented. Two types of drag bits, a conical and a plow bit, were tested in a hard sandstone rock with jet pressures of up to 20,000 psi. Jet locations investigated were in-front and behind the bit. For each jet mounting location, three jet impingement distances with respect to bit tip were tested. The closest jet impingement location to bit tip was found most effective, providing the greatest force reductions on the bit. Overall, significant bit force reductions up to 50 percent were obtained with jet assist. Also observed was a drastic reduction in airborne dust when jets were employed.

Jan 1, 1986

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By Ross R

Although mining is an old industry its management is quite a new science, and its complications are now being recognised as demanding expert knowledge in many branches of technical and professional education. Not the least amongst these isaccountancy, for probably its most important problem is "How to control the expenditure." Unlike most businesses a mining company stands almost entirely in the light of a purchaser in the world's markets, and not as a seller, except say for product so the established and perfected systems of modern industries cannot be adopted for mining purposes. For this reason it has been left for late years to consider the matter seriously, and now a number of well-managed concerns have devised costs systems to suit their own requirements.Very little, however, has been published and even that is disjoined and difficult to make use of. Some of the costs systems in vogue, although elaborate and imposing, are not of very great value for keeping check on wasteful expenditure, or for displaying the commercial effect brought about 'by any particular change in practice, or by an addition or alteration to a portion of existing plant.

Jan 1, 1912

A forecast of energy demand in the non-commu- nist world to the year 1990 is presented with com- ments on the expected effectiveness of conservation efforts in achieving more efficient utilization of energy. A forecast of energy supply for the same period is presented showing the contribution of oil, gas, hydropower, coal, and nuclear fuels, with brief comments on the factors constraining the rate of growth of non-oil energy supplies. The role of `synthetic fuels', i.e. liquid or gaseous fuels produced from coal, oil shale, and tar sands, is reviewed with brief discussion of factors affecting the development of this industry. In somewhat greater details, the growth of demand for oil by geographic regions is analyzed. Particular attention is directed to the source of the oil supplies which will be required. The anticipated rate of discovery of new oil reserves is discussed with comments on lead times required in the development of new discoveries in hostile environments such as the Arctic and deep oceans. The continuing importance of oil supplied from countries which are members of the Organization of Petroleum Exporting Countries (OPEC) is illustrated. Oil will continue to be the marginal ('balancing') source of world energy supply throughout the forecast period and although it now appears that oil supplies will be sufficient to balance the energy equation during the 1980s, little flexi- bility will exist to cope with unexpected growth in demand or slippage in supply. Prudent energy re- source management will require major efforts to stimulate conservation and also to stimulate the rapid development of conventional and new forms of energy supplies and changes in energy consump- tion patterns to utilize the new supplies. Because of the long lead times and the massive capital require- ments involved, governmental policies are needed soon which will stimulate conservation and which will encourage businesses to move rapidly to assure the energy supplies the world will require in the 1990s.

Jan 1, 1978

By Sidney Katell

Covering the period from January 1961 through December 1961, this report is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. It is also the third report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related facilities, came from the following sources: 1. A.A.C.E. Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigation. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Industrial and Engineering Chemistry. 11. Nucleonics 12. Oil and Gas Journal. 13. Petroleum Engineer for Management. 14. Petroleum Refiner. 15. World Oil.

Jan 1, 1962

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

Froth flotation processes are carried out in flotation cells that are grouped into banks, and these banks are interconnected, forming a flotation circuit. A literature review shows the existence of papers related to flotation circuit design based on mathematical programming. However, due to the complexity of solving the mathematical model in most of the work, it is considered that a small number of species is present in the feed to the circuit, which differs from practice. In addition, simple bank models are generally used. This paper presents a methodology for designing mineral concentration circuits that overcomes the problems mentioned. It allows the use of more suitable cell or bank models and the inclusion of several species. The methodology is based on two phases. The first phase identifies the set of optimal structures using discrete values of stage recoveries, solving several mixed integer linear programming (MILP) problems. In the second phase, the optimal design for each of the structures obtained in the previous phase is determined using a suitable model for the recovery at each cell or bank, which results in a mixed integer nonlinear programming (MINLP) model. The design of a copper concentration plant with eight species and the design of a zinc concentration plant with three species and five size fractions by species are used to validate the proposed methodology. The structure of the cells in the rougher and cleaner banks deliver structures that are novel.

IN this paper it is proposed to present certain features of operating practice at the Port Pirie works of The Broken Hill Associated Smelters Proprietary Limited, in the smelting in a blast furnace of lead ores carrying a high concentration of zinc.The subject matter selected for presentation is:(i) The effect of zinc on lead blast-furnace operations, together with an outline of the methods adopted in actual practice in dealing with the zinc problem.(2) Development of the height of tuyere above the bottom of the jacket, and the extension of the tapping interval and the combined effect of both factors upon the lead content of blast furnace slag.It will later be seen that one phase of the investigation carried out in connection with the effect of zinc on blast-furnace operations was largely responsible for the decision to increase to a marked degree the height of the tuyere above the bottom of the jacket.Due to this interdependence, it has been considered advisable to deal with the two features above mentioned.The high concentration of zinc in the lead-bearing materials smelted at Port Pirie has brought with it those troubles which are associated with zinc in the smelting operation.In the early stages of the history of The Broken Hill Associated Smelters Pty. Ltd. the trend towards increasing cost for labour, fuel, and stores, etc., rendered it necessary to increase the lead content of the charge, and reduce to a minimum the quantity of barren flux used.

Jan 1, 1931

By John D. Spencer

Projects aimed at achieving the least disturbance to the Nation's air, water, and land resources in the mining and utilization of coal continued to be a feature of the Bureau of Mines coal program. This reflects the current concern about damage inflicted on the environment by our growing and increasingly affluent society. Mine Health and Safety research, along with investigations related to all other aspects of coal extraction and use, also continued to be implemented and expanded.

Jan 1, 1970