Search Documents

By L. Parthasarathy, S. K. Pan, M. P. Srivastava

"Total iron ore reserves in India, as reported by the Indian Bureau of mines, are 23.6 billion tons. Hematite iron ore reserves constitute about 45 % of the total reserve. If we go by the National Steel Policy-2005 projections, India’s supply of hematite iron ore would not last more than 40 years. Laboratory investigations were carried out for the development of a process flow sheet for treating low grade as well as Banded Hematite Quartzite (BHQ) iron ore. The purpose of these investigations was to aim for better resource utilization.Beneficiation studies were conducted on samples of low grade and siliceous iron ore from the Dalli mines, a captive mine of the Bhilai Steel Plant and BHQ ore from Southern states of India. The process flowsheet, developed for upgrading of low grade iron ore, incorporates wet screening of the ore at 0.5 mm, followed by grinding of the +0.5 mm fraction to below 0.5 mm. The whole –0.5 mm fraction, after grinding, was treated in a conventional hydro-cyclone and stub cyclone followed by treatment in Wet High Intensity Magnetic Separator (WHIMS). This resulted in a concentrate product having >66% Fe content from a feed containing 55.5% Fe with an iron recovery of 48 %. The process flowsheet developed for treating BHQ ore in the laboratory resulted in an increase in iron grade in the concentrate from 43.4 to 61.3 Fe % with a yield of 51.7 % .INTRODUCTIONThe classification of Indian iron ore resources have been made compatible with United Nations Framework Classification (UNFC), which is more scientific and has been adopted in most countries in the world. Iron ore reserves and resources estimated using the UNFC classification system, as of April 01,2000 are about 12,906 million tons of hematite ore and 10,628 million tons of magnetite ore. The Indian Bureau of Mines (IBM) has given a breakdown of these reserves by designation as either lumps or fines of hematite iron ore (Table 1). The percentage of the reserves reported lumps and fines are 42 and 34% of the total reserves respectively. High grade iron ore is less than 10% of the total reserve."

Jan 1, 2008

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

A Robust Chemically Enhanced Electrostatic Separation Technology Physical separation processes such as gravity, magnetic and electrostatic separations are extensively used in heavy minerals separations. Electrostatic (aka High-Tension) separation facilitated by the conductivity differences, in particular, is used for separating rutile from zircon. Although electrostatic separation is effective, it is not efficient. It suffers from separation efficacy issues owing to sensitive variables such as humidity, surface contamination, particle sizes and the temperature of the feed and other equipment parameters. The variations in the process conditions especially with humidity, temperature of the feed and the mineralogy and surface impurities can cause significant reduction in the separation resulting in production rate losses and product quality issues. Cytec Industries has developed chemical enhancement technologies for electrostatic separation for rutile -zircon separation from the heavy minerals. The major advantage of our technology is its higher separation efficacy in the first pass, substantial energy savings and most importantly its ability to do separation at room temperatures. The bolt-on nature to the existing electrostatic also an added feature that reduces the capital expenditure significantly. The separation efficiency between rutile and zircon was increased as much as 8 - 11 per cent compared to control. It is possible to extend the chemical enhancer technology to problematic feeds and other mineral systems that are not easily amenable to conventional electrostatic separation.

Sep 13, 2010

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By J. Werfling, J. R. Kiehl

SUMMARY: The effects of blasting on structures are assessed on the basis of the maximum amplitudes of the occuring vibration velocities. If the standard values in the German Standard DIN 4150 are not exceeded, damages to structures are not to be expected. The estimation of the maximum vibration amplitudes is usually based on experience or on emperical formulae. However, a comparison of expected with measured values shows that these estimations are not conservative, particulary in case of small distances between blasting locations and structures. More reliable predictions are possible on the basis of numerical analyses, which simulate the three-dimensional propagation of waves with consideration of the geomechanical and geometrical conditions. In addition to the expected velocities, these analyses also allow the determination of stresses resulting from dynamic loading. If the dynamic stresses are known, the effects of blasting on structures can be predicted. ZUSAMMENFASSUNG: Die Auswirkungen sprengbedingter Erschütterungen auf bauliche Anlagen werden in der Praxis auf der Grundlage der Maximalamplituden der auftretenden Schwinggeschwindigkeiten beurteilt. In der DIN 4150 werden Anhaltswerte angegeben, bei deren Einhaltung Schäden von Gebäuden nicht zu erwarten sind. Die Abschätzung dieser Schwing-geschwindigkeiten erfolgt meist auf der Grundlage von Erfahrungswerten oder empirischer Formeln. Der Vergleich der prognostizierten Werte mit Meßergebnissen zeigt jedoch, daß diese Ansätze insbesondere dann, wenn die Abstände zwischen den Sprengorten und den Gebäuden gering sind, nicht konservativ sind. Zuverlässigere Prognosen sind auf der Grundlage von numerischen Berechnungen möglich, in denen die räumliche Ausbreitung von Erschütterungen unter Berücksichtigung der geomechanischen und geometrischen Verhältnisse simuliert wird. Mit derartigen Berechnungen können die zu erwartenden Schwinggeschwindigkeiten und die aus der dynamischen Beanspruchung resultierenden Spannungen ermittelt werden. Dies ermöglicht Aussagen über die Auswirkungen sprengbedingter Erschütterungen auf Bauwerke. RÉSUMÉ: Les conséquences de vibrations résultantes d'explosions pour des bâtiments sont estimés dans la pratique à partir des amplitudes maximales des vitesses d'oscillation. Dans la norme allemande DIN 4150 des valeurs d'orientation sont données, avec l'observation desquelles de dommage à des bâtiments n'est pas à présumer. Ces vitesses d'oscillation sont estimés généralement à partir de valeurs d'expérience ou de formules empiriques. La comparaison des valeurs prédits avec des résultats de mesures montre cependant que ces hypothèses ne sont pas conservateurs, en particulier si les distances entre les lieux de sautage et les bâtiments sont petites. Des prédictions plus fiables sont possibles à partir de calculs numériques, dans lesquelles la dissipation spatiale de vibrations est simulée en considération de la situation géoméchanique et géométrique. Avec tels calculs les vitesses de vibration à présumer et les contraintes résultantes de l'effort dynamique peuvent être établies. Cela permet de constater sur les conséquences de vibrations résultantes d'explosions pour des bâtiments.

Jan 1, 2003

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

By G D. Price

Scheelite mineralisation east of the main divide in' the Southern Alps of New Zealand was originally identified by Royden Thompson who is now a geologist with the NZ Geological Survey. This mineralisation was brought to the attention of CRA in 1978. Reconnaissance surveys were carried out in 1979 to delineate the extent of the mineralisation. This was undertaken using ultraviolet light examination of the sediments within the major drainages in the Southern Alps. This defined tentative zones of prospective mineralisation. As a result of this, preliminary reconnaissance, exploration licences were applied for -those areas in which indications of scheelite mineralisation were strongest. A total of 1737 km2 of ground was applied for within four exploration licences. These covered the main Southern Alps mountain chain between the Haast/Wanaka highway and the Mt Cook National Park.

Jan 1, 1983

By Louis H. Berkelhamer

"INTRODUCTION ""Free silica"" includes all free forms of silicon dioxide, such as quartz, chalcedony, tridymite, cristbbalite, opal, diatomaceous earth, and lechatelierite. The term, has been used rather loosely however, as synonymous with quartz, as quartz is the most abundant form of free silica. ""Combined silica,"" on the other hand, has been reserved to denote silica combined with other elements as silicates.Improvements in methods for the determination of free silica, and quartz in particular, have been the subject of considerable interest during the past decade, owing mainly to the accented and increased knowledge concerning quartz as a causative factor in silicosis. Analysis for quartz, however, is of importance in many other fields, including the determination of quartz in ceramic raw materials, such as feldspar and clay; the evaluation of a beneficiation procedure by the ore dresser, such as in the concentration of iron ore; control studies of a manufactured product, such as silica brick; and routine analysis of rock, mineral, and ore samples by chemists and petrographers."

Jul 1, 1944

By G. Swan, E. Nordlund, P. Zhang

"SynopsisThe most widely used support design damage criterion for rockburst-prone mines is based upon kinetic energy, which is proportional to the square of the ejection velocity and is commonly expressed in terms of peak particle velocity (PPV). Field monitoring and back-analyses have shown that ejection velocities of the order of 10 m/s and higher can result from seismic events of moderate magnitude. Such velocities are much higher than those predicted using PPV obtained from scaling laws. It has also been found that the peak ground motion (i.e. PPV) on the surface of an excavation is preferentially amplified (by four- to tenfold) compared to the motion in solid rock at a similar distance from the source. However, the wave propagation and interaction processes involved within the fractured rock in generating high ground motion are very complex and are not well understood at this time.In this paper, velocity amplification was investigated by modelling the dynamic interaction between fractured rock and a free surface using a 2D discontinuum-based numerical program, UDEC (Universal Distinct Element Code). A 1D model with a fractured zone was used to represent the fractured rock. Velocity amplification, quantified by PPV, predicted at the free end of the model was 2.0–3.6 times higher than the input velocity. It was found that the wave frequency, fracture stiffness, fracture spacing, and thickness of fractured zone are the main factors that affect the velocity amplification. The results have proved that the interaction of the seismic wave and multiple fractures near the free surface strongly influences the ground motion.IntroductionSince mining-induced seismicity is almost inevitable in deep mines, ground support is generally employed to mitigate the risk of seismically-induced damage. The most widely used support design criterion for seismicallyprone mines is one that seeks to maximize the absorption of the kinetic energy (plus potential energy if a gravity component is considered) of key rock blocks. Based on this criterion, design methods for rock support were first proposed by Wagner (1984) in South Africa and later improved, among others, by Roberts and Brummer (1988) and Kaiser et al. (1996)."

Jan 1, 2015

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

Effect of Activated Carbon on the Leaching of Cobalt-Rich Ferromanganese Crust in Sulfuric Acid

Sep 13, 2010

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

The efficient and profit-maximising daily and long-term management of the Vera Nancy resource depends on decisions based upon assay data. This paper examines the range of sample sources, the methods of sample collection, assay techniques and Quality Assurance used by the mine. The orebody has a relatively low nugget effect for a gold mine (around 25 per cent) and this greatly assists in reducing sampling error and producing reliable assay data for production decision-making. Reconciliation between mine and back-calculated mill grades generally sees the mine under-calling mill grades by around four per cent.

Jan 1, 2000

Most analysts determining tungsten trioxide in low grade samples are aware that colorimetric procedures do not possess the inherent disadvantages of gravimetric methods operating on milligram quantities of tungsten trioxide. Apart from the inaccuracies associated with weighing four or five milligrams of ignited oxide in a platinum crucible of about 30 gm. weight with a large surface area to absorb moisture, using a 5 gm. charge on samples less than about 0·15 per cent tungsten trioxide, it is extremely difficult toget complete or pure precipitation of tungsten with cinchonine, cinchonine plus alpha benzoin oxime, rhodamine B or any other of the commonly used precipitants. Table 2', No. 8, illustrates the low results obtained by gravimetric as opposed to colorimetric procedures. In addition the colorimetric determination requires only a small portion of the time consumed by gravimetric practices and the increased accuracy obtainable in low ranges together with the saving in time made it highly desirable to develop a colorimetric method suitable for King Island ores.The most commonly used colorimetric method is that introduced by Feigl and Krumholz (1932), since modified by various investigators (Grimaldi and North, 1943; Sandell, 1946; Westwood and Mayer, 1947; Gentry and Sherrington, 1948; Freund, Wright and Brookshier, 1951; Grouthamel and Johnson, 1954; and others). Stannous chloride is used to reduce tungsten followed by colour development with a thiocyanate, usually sodium, potassium or ammonium.Other reducing agents have been proposed (Emery and Curtis, 1948), but only in recent years have the conditions governing maximum colour development been fully estab...

Jan 1, 1958

By Lon Santis, Dale Ramsey

The use of aircraft to support blasting operations in mines, quarries and construction sites goes back to the early days of aviation. Invaluable at times, aircraft use has been limited by cost, the unpredictability of weather impacts and other factors. Recently several technologies have matured to open up a new way to acquire aerial data with unmanned aircraft systems (UAS), commonly called drones. Equally important, the U.S. Federal Aviation Administration has recently implemented an exemption process and rulemaking to implement the commercial use of UAS into the United States’ National Airspace. The skies are opening for many applications of UAS. The most notable may be photogrammetry, which is the science of making measurements from photographs, especially for determining the exact positions of surface points.

Jan 1, 2016

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

[ ]

Jan 1, 2009

By David L. Veith

As the basis for the State of Minnesota's Regional Copper-Nickel Study environmental evaluation, hypothetical mine models were developed ranging in ore capacity from 5.35 to 20.00 x 106 mtpy. Open pit and underground mining operations were defined utilizing conventional methods of ore extraction. Processing of the copper-nickel sulfide material involved conventional bulk flotation of the valuable minerals, with maximum water recycle And tailing disposal. Flash smelting and electrolytic refining of the concentrate resulted in 0.10 x 106 mtpy copper plus nickel metal, plus associated cobalt and precious metals. Variations in model parameters allowed environmental trade-offs to be identified.

Jan 1, 1980

By J. Antrekowitsch

Keywords: residues, fluorides, chlorides, zinc, steel mill dust The recyclability of various nonferrous metal wastes often suffers from a relatively high fluorine and chlorine content. Both are inserted in most cases by the use of plastic contaminated scrap and a wide variety of different coatings. These halogens lead to poor product qualities and off gas contamination. Especially the history of zinc recovery from steel mill dusts shows, that the today common hydrometallurgical options are on their limit and therefore are not sufficient in most cases. This thermochemical study should give more information about different pyrometallurgical options, that offer both a chlorine and fluorine reduction and efficient zinc recovery, preferably in one process step. Selective evaporation in different atmospheres and conversion with the use of hydrogen are the main parts in this study. The results combined with the relatively small information available from literature should provide a basis for further investigations in this field.

Jan 1, 2005

By Nageswararao K

A series of tests was carried out on one of the rock-pebble milling circuits treating complex nickel ores at Kambalda Nickel Operations of Western Mining Corporation. A mathematical model to describe the behaviour of a 508 mm hydrocyclone was developed from the data.A "flat" reduced efficiency curve was observed for the system. This was attributed to a marked difference in the specific gravity of different size fractions of the feed. A modified approach in describing the shape or the reduced efficiency curve resulted in accurate prediction of the hydrocyclone performance.

Jan 1, 1981