Search Documents

By Helen D. Robinson

The seawalls that surround Ellis Island were constructed in the early 1900s and now show varying degrees of deterioration. An innovative approach to the structural repair of the seawalls was developed, which consisted of the use of micropiles for stabilization of vertical and horizontal seawall movements. The micropiles were installed through the existing seawalls and penetrated through a thick overburden, consisting of soft alluvial deposits and relatively hard glacial till, and were bonded into Manhattan Schist. Drilling of the micropiles often encountered timber and other obstructions. The selection of micropiles for stabilization of the seawalls offered significant advantages over other foundation systems and over alternative soil improvement techniques. They allowed drilling through a variety of materials without the need for significant retooling or changes to the drilling procedure. This reduced the impact of foundation construction on the sensitive historical landscape and structures, and prevented the need for significant foundation work from the water side of the seawalls. In addition, micropiles offered relatively high installation rates and flexibility to adapt to the varying conditions along the seawalls.

Jan 1, 2008

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion. In several cases, breaches occurred between the gravel pit and the river. Initial evaluation of several sites that experienced these breaches showed that impacts to the river system were complex and varied significantly from site to site. The impacts to the adjacent river system may be viewed as positive and negative. Several flood-plain-mining sites in Oregon located in areas of historic river flow reverted to active riverbeds. In many cases, state and federal fisheries biologists and university researchers saw the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries —Mined Land Reclamation Program (DOGAMI-MLR) is studying the effects to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound flood-plain decisions regarding mining.

Jan 1, 1999

By F. C. NINNIS

AT THE Belmont mill, the pregnant solution is de¬livered to a 30 by 10-ft. tank, from which it is pumped to three Merrill clarifying presses of the sluice-bar type, whence it flows through the meter to the precipitation supply tank. ?The solution for precipitation is pumped by a 10 by 10-in. Aldrich triplex pump and delivered through a 6-in. line to the forty-eight triangular frame Merrill presses at the head of the mill. Zinc dust is fed in at the pump suction and the solution precipitated to 0.01 to 0.02 oz. silver. The solution flowing from the presses is tested at 1-hr. intervals with sodium sulfide. All solution is precipitated to the same value; 4J tons of solution are precipitated for each ton of ore treated and the presses are cleaned every 15 days. The product from the presses' is dumped into steel cars having steam-jacketed bottoms, in which they are dried until the moisture content is between 15 and 17 per cent. when 8. per cent. of soda and .3 per cent. of borax are added and the contents thoroughly mixed. In the case of special clean-ups, the precipitate is tested and the flux is added to meet the requirements.

Jan 1, 1921

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By A. Motamedi

Indoor localization has gained importance as it has the potential to improve various processes related to the lifecycle management of facilities and to deliver personalized and location-based services. Radio Frequency Identification (RFID) based systems, on the other hand, have been widely used in different applications in construction and maintenance. This paper investigates the usage of RFID technology for indoor localization of RFID equipped movable assets during the operation phase of facilities. The location-related data on RFID tags attached to fixed assets are extracted from a Building Information Model (BIM) and can provide context-aware information inside the building which can improve Facilities Management (FM) processes. The paper proposes a new approach to use received signals from available reference tags in the building attached to fixed assets to locate movable assets. The approach uses signal pattern matching and clustering algorithms for localization. As a result, a user equipped with an RFID reader is able to estimate the location of target assets, without having access to any Real- Time Location System (RTLS) infrastructure. A case study is performed to demonstrate the feasibility of proposed methods.

Aug 1, 2013

By D. Harrington

United States newspapers of 25 or 30 Years ago ran headlines every few weeks telling of some mine disaster. Each disaster was a first-page attraction for a day or so then was forgotten until the next sensational event, frequently another mine disaster, a few weeks later. Interspersed with the large mine disasters were the so-called ?snipping? mine accidents that caused the death of one or two mine workers. The summation of mine fatalities of all types usually exceeded 3,000 a year, and nonfatal accidents to workers in mines of the country approximated 250,000 annually. From 1906 to 1910, inclusive, there were 84 major explosion disasters (about 17 per year) in. United States coal mines. The resulting fatalities totaled 2,388 for the 5-Year period. These frightful catastrophes helped the number of fatalities in coal mines of the country to reach the enormous total of 13,288 for the 5 years, or an average of 2,658 per year.

Jan 1, 1940

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By Javier Támara

Para aumentar la productividad de la empresa minera es necesario conocer el sistema de aire -en tanto se prioriza los intereses de los clientes, y así se puede suplir todos los componentes necesarios para garantizar una máxima eficiencia y confiabilidad del sistema completo de aire comprimido que va desde el filtro de admisión hasta el punto de uso. En ese sentido, el presente texto describe las estrategias para realizar Solucionazing en ahorro energético y así aumentar la produtividad de los sistemas de aire.

Aug 25, 2002

By J Pease, P Cameron, D Drinkwater

"In the 1990s metal prices were trending in a long-term decline and the usual cost-cutting exercises were adopted. Cuts to research and development made innovation difficult and the outlook was grim. But necessity is a strong motivator, and these conditions spurred the Mine to Mill movement that optimised across organisational ‘silos’ and utilised new technology tools, innovative software and increased computing power. Many applications of Mine to Mill exploited the fact that comminution is usually the site processing bottleneck and blasting is more efficient at breaking rock than grinding. This approach sought to: understand and characterise rock breakage from mining to the milldevelop models and simulators for blast design, fragmentation, crusher and mill circuitsdevelop tools to measure in real time the particle size distribution of rocks on run-of-mine (ROM) muck piles, at the primary crusher truck dump pocket and on conveyorsensure effective communication across the silos between geologists, blast design engineers, mining engineers and metallurgists.These methods and the technology tools available in the 1990s were widely adopted at numerous sites around the world with significant benefits. Semi-autogenous grinding (SAG) mill throughput increases of 10–20 per cent were common. This was the advance the industry desperately needed. It was low capital cost; it was obvious. It was here to stay.Except, in too many cases, it didn’t. In the minerals price boom of the 2000s Mine to Mill was no longer necessary to ‘survive’, even though it was still good business. Some operations, including some of the early success stories, slipped back to old habits of optimising within organisation silos instead of across them. Fortunately, other operators still embraced Mine to Mill and developed new techniques. Mine to Mill was still successful, but not as widely adopted as we had expected it to be. Now the boom has ended and operations are again under cost pressure. Since these are the same circumstances that created Mine to Mill, it seems time to achieve the wider adoption. Since the 1990s many new or advanced technology tools are now available for Mine to Mill projects: blasthole sensors, new explosives formulations, new blasting techniques and modelling, ore tracking devices, improved image analysis to determine size, texture and colour of coarse ore, grade sensors, whole-stream simulation tools, and even more powerful computing hardware and data analysis software. If we could achieve so much in the 1990s, how much more can we achieve today when we have the same imperative, the same potential and a larger number of high technology tools?Citation:Cameron, P, Drinkwater, D and Pease, J, 2016. The ABC of Mine to Mill and Metal Price Cycles, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Pooley F. D

The coal measures of the South Wales coalfield contain at least 50 horizons at which coal seams are known, to occur. More than 300 samples of coal were collected from these coal measures and this paper outlines thefindings of an investigation of the pattern and distribution of 12 trace elements in South Wales coals. A comparison of trace element contents of the South Wales coals is made with trace element values found elsewhereand an attempt was made to establish the organic affinity of the elements in different seams and in the coalfield 'as a whole. An important function of such an analysis is to determine the order of abundance of trace elements and this was performed for individual seams and for the whole coalfield.The interrelationship of certain elements in some seams is also examined with a view to understanding the effectiveness of such an approach to seam correlation.Ranges of values are quoted together with the mean values of the various elements. Variations of elemental values within a seam section and over the coalfield as a whole are discussed.

Jan 1, 1977

By André de Jager, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge. The mine has installed a technologically advanced seismic monitoring system with monitoring sensors positioned at various locations and depths throughout the pit. The electronic data recording system records all relevant information on a continuous basis with early warning signals in cases of potential danger. From the information recorded by this micro-seismic system it was established that the energy release into the high-wall is predominantly influenced by the mining rate, water content and mining tempo and to a lesser extent by the blasting operations. To limit the negative effects of blast vibrations, the use of Electronic Delay Detonators (EDDs) was introduced. The optimal delays were determined through signature trace analysis. The vibrations obtained during blasts initiated by means of electronic delay detonators were monitored and compared to those traditionally obtained when standard pyrotechnic delay detonators had been used. The measured vibration data indicated an improvement of 25% to 100% drop in vibration amplitude compared. The accuracy and programmability of EDDs presented huge potential for blast optimization in terms of limiting the vibrations without compromising fragmentation. The whole project was conducted over a twelve week period with some 4000 EDDs. The average size of a blast was in the order of 350 holes using about 40kg explosives per hole, which equates to 14,000 kg explosives over 12 different blasts. The paper deals in detail with the blast optimization process with regard to: - determining the rock response time; - establishing the signature traces; - analyzing the wave interference patterns; - predicting the direction of constructive and destructive wave interferences; - optimizing of the inter-hole and inter-row delay periods; - measuring the ground vibrations. The results obtained during electronic blasting are compared to those obtained during pyrotechnic blasting. Comparisons are being made with regard to the following: - ground vibration measurements; - pit wall stability measurements; - blast safety.

Jan 1, 2006

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By B. E. Warren

Jan 1, 1965

By Bertrand L. Johnson

Before 1914 , Chile , because of her extensive resources of natural nitrates , practically monopolized the world markets for one of the leading fertilizer materials . Since nitrogen also is an important war material , constituting in fact the principal ingredient in many high-powered explosives , the World War and the widespread insistence upon national self- sufficiency for war materials brought about the development of nitrogen fixation plants in all of the larger countries . The production of by- product ammonia from gas and coke plants was likewise stimulated . As a result , Chile , even after the ocean lanes were reopened , was forced to fight for her lost markets . Since the world capacity to produce is still far in excess of annual consumption , the competition between natural and synthetic supplies has been keen and prices have fallen below pre-war levels . Chile has recently succeeded in unifying her industry , utilizing the most efficient process now in operation, and the Government is a partner in the new company that will take over all of the present producing companies . These developments place Chilean nitrate of soda , in a much more favorable position among the markets of the world . More intense competition will undoubtedly follow and , in order that those interested may become familiar with the fields upon which the nitrogen conflicts of the near future may be waged , the following general summary of the nitrogen industry has been prepared .

Jan 1, 1931

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

By H. E. Urtubia, C. W. Bailey

"BHP-Billiton’s Minera Escondida Limitada is one of the world’s largest copper producers. It treats a combined 88 million tons of copper ore per year through its two concentrators: Los Colorados and Laguna Seca. Over the past three years, metallurgical sampling has been performed at the Laguna Seca concentrator to calibrate both the JKSimMet and JKSimFloat grinding and flotation simulators. In the past, the calibrated simulators have been used to predict the effect of changes in operating conditions in the grinding and flotation circuits separately. To assist in the development of future processing options, predictions were required of the effect of changing grinding circuit conditions on flotation performance. This was achieved by using an integrated grinding and flotation simulation. The grinding circuit performance was predicted under different operating conditions (such as tonnage rate and product grind size) using JKSimMet, and these results were then used in JKSimFloat to predict the flotation performance for the new grinding circuit product. This combination of the simulators allows both the effects of residence time and grind size on flotation performance to be investigated.This paper presents the first combined grinding and simulation modelling and simulation case study using JKSimMet and JKSimFloat. The modelling and simulation methodologies for the grinding and flotation circuits are discussed along with the circuit simulations that were performed. The simulator predictions are presented in conjunction with independent laboratory results of the new operating conditions. The ability to predict flotation circuit performance based on changes in grinding circuit performance is also discussed. This methodology provides improved predictions of flotation circuit performance when grinding circuit changes (including grinding capacity increases) are made.INTRODUCTIONOver the past decade, the grinding and flotation research groups at the Julius Krutschnitt Minerals Research Centre - JKMRC (Brisbane, Australia), University of Cape Town (Cape Town, South Africa) and McGill University (Montreal, Canada) have been developing a methodology for optimising grinding and flotation plants using actual plant data together with semi-empirical sub-process models. The project is being conducted as part of the Australian Minerals Industry Research Association (AMIRA) P9 Project, titled “The Optimisation of Mineral Processes by Modelling and Simulation”. The project first commenced in 1962 and is currently in its “Nth” phase."

Jan 1, 2007

By Lowell B. Moon

The Stange and Byrnes Heirs manganese mines, adjoining properties in Bland and Giles Counties, Va., have produced at least 20,000 long tons of concentrates containing 8,000 long tons of manganese. They were selected as the site for a strategic-mineral development project because of the existence of geologic possibilities for extensions of the known ore body. In plan, the long dimension of the ore body parallels the axis of a major anticline. Localization apparently is due to longitudinal and transverse fracturing incident to two-way folding. That the manganese oxides were deposited by downward-moving solutions is suggested by the fact that mineable concentrations are confined to a coarse, porous sandstone under-lain by impervious silt and clay. Bureau of Mines project work began on January 15, 1941, and was completed on April 23. The work sampling the faces of the pit, bulldozer trenching, and churn drilling. Pit sampling consisted of 132 channel samples usually 5 feet long and taken at 20-foot intervals. Seventeen trenches aggregating some 4,500 feet in length were dug by the bulldozer. Trenches averaged 12.6 feet in width and 5 feet in depth. A total of 1,978 feet of churn drilling was done in 33 holes. In preparation for churn drilling it was necessary to construct roads to 21 of the 33 sites. A total of 2,867 linear feet of road averaging 13 feet in width was built.

Jan 1, 1950

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

Study on New Tungsten Beneficiation Technological Flow Sheet of Shizhuyuan Polymetallic Mine

Sep 13, 2010

By W Roy

When it comes to plan implementation and securing success in organisations in the 21st century, if there was such a thing as the secret to success it would be effective communication. Commoditisation brings financial, operational and cultural advantages to organisations that use effective communication. Effective communication tools turn æpeople problemsÆ into system control solutions, removing personality clashes that hide procedural malfunctions. By introducing communications frameworks available in the market place today, and case studies of their use, this paper provides insights into the successes available to organisations courageous enough to redefine their communications for the 21st century.

Jan 1, 2006