Search Documents

By Michael J. Sapko, Gregory M. Green, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of US coal mines. The last comprehensive survey of this type was performed in the 1920s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA's 10 bituminous Coal Mine Safety and Health Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low-temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920s. This finer size coal dust in intake airways would require more incombustible matter to be effectively inerted than the 65% incombustible specified in current regulations.

By Stanton L. Tainter

As a part of a wartime program to aid in the development of known ore bodies and in the discovery of hitherto unknown deposits of strategic minerals, the Bureau of Mines investigated the feasibility of diamond-drilling the Christmas copper deposit, in Gila County, Ariz., to increase the reserves of milling ore. Upon recommendation of the examining engineer, drilling was begun in September 1942, from the bottom (770) level of the mine. One month later, in cooperation with the Bureau, the Federal Geological Survey started geologic mapping of the mine workings. Since extensive and costly development would be required, the War Production Board concluded that ore below the bottom level could not be mined at that time because of the wartime shortages of equipment and man-power. In January 1943, drilling was moved to the 300 and 400 levels to locate reserves readily accessible for continued production of fluxing ore. This drilling, which was under the supervision of L. G. Marshall, was completed in January 1944.

Jan 1, 1948

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By R. Lincoln

A surplus of vanadium has resulted from the tremendous output of uranium, of which vanadium is a byproduct. More knowledge of the properties and characteristics of vanadium as a pure metal has been needed so that industry can take advantage of its availability and use it according to the best principles of conservation. Besides the problem of utilization, there is the ever present need of finding new materials which will satisfy specific and demanding requirements of science and engineering; vanadium or one of its alloys may possess the latent potential for filling some of these needs. Thus this? research project was undertaken by the Bureau of Mines to determine and examine some of the physical and mechanical properties of pure vanadium. A corallary investigation was the determination of the effect of the interstitial contaminants, oxygen, nitrogen, and carbon, on unalloyed vanadium. The vanadium used for these determinations was principally the product of experimental production of the Bureau. The evaluation of this material, as small quantities became available, provided most of the data that have been obtained.

Jan 1, 1962

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

In spite of the many contributions that have been made to our knowledge of the creep properties of polycrystalline lead, the precise influence of various factors on these properties is not yet fully understood. Indeed, the position is such that several important points in connection with the creep of lead are a matter of controversy. This has been brought about largely by the fact that, in the case of lead, the changes that are produced in the creep behaviour by slight variations of such factors as the purity, grain sizeand previous treatment are out of all proportion to the magnitude of these variations.In order to study the fundamental properties of lead as related to creep, and so gain a more enlightened perspective with which to consider the creep of lead in general, the work that is described in a series of papers, of which the present paper is the third part, has been carried out. It deals with lead in the form of single crystals.It has been shown (1) - (3) that the grain boundaries as well as the actual grains play a part in the creep of polycrystalline lead. The present work, by eliminating grain boundaries, enables the. contribution of the grains themselves to the process of creep, in other words, crystalline creep, to be studied effectively.This object was, possibly, the major one in this work.

Jan 1, 1940

By D. O’Connor, A. Pytlik, D. J. Corbett

The resistance of yielding rockbolts to multiple impact loads was tested by means of a drop hammer. The methodology was based on the ASTM D7401-08 standard as well as the requirements specified for rockbolts by Luossavaara-Kiirunavaara Aktiebolag (LKAB – a Swedish mining company) and the Safety In Mines Research Advisory Committee of South Africa (project number GAP 423). During the tests, the loading force and bolt elongation were measured with a sampling frequency of fs = 19.2 kHz. In order to analyse the phenomena involved, the tests were recorded using two independent high-speed video cameras (600 and 1000 frames per second) and one thermal camera (128 frames per second). The tests demonstrated that all the samples transferred double the gravitational potential energy of Ep = 50.85 kJ from the impact load of mass m = 2825 kg and impact velocity of v = 6.0 m/s without failure. Damage to the bolt-resin contact in the upper anchoring zone of the bolt in the steel tube occurred after subsequent impacts. As a result, the macro-deformed bolt exhibits additional yield, and its operation following the shearing of the resin bond is similar to that of a ‘cone bolt’. Only one test resulted in damage to the threaded bolt rod-nut coupling, during the fourth impact; however, no damage to the bolt-resin contact zone was observed.

Nov 6, 2023

By I. R. Firth, D. L. Taylor

Metal mining operations, in particular gold mining operations, use intensive ore control procedures in order to manage the extraction of ore zones from benches containing both ore and waste material. Typical grade control procedures rely on blast hole samples to indicate ore grade. Statistical techniques and geological controls are then used to create two-dimensional polygons, which indicate zones of material designated as ore. These ore-polygons are calculated using pre-blast material locations and are generally not corrected for rock movement caused by blasting. This lack of correction appears to exacerbate the material mischaracterization problem of sending ore to the waste dump and/or waste to the mill. One Nevada gold mining company has estimated that this could be a $10 million per year problem for their operations. Using a simplified vector field algorithm, a method of taking point movement data and interpolating post-blast positions for all nodes in a polygon has been developed. Currently working in 2-dimentions (X-Y), this algorithm utilizes the movement vectors calculated from pre-and post-blast positions of targets placed in a blast, to generate a spatial transformation function for any point on the bench. This transformation is then applied to the nodes of the ore-polygons to produce modified dig lines ore polygons reflecting distortion and movement resulting from the blast. The method as implemented uses common mine planning routines and is performed using the Surpac software suite. The method may be adapted to use any pre-and post-blast point movement data available, and most mine planning suites include the simple interpolation algorithms used. Keywords: Blast movement; Ore control; Open pit blasting; Grade control

Jan 1, 2003

By M. P. Hay

"For a model to be successful it must address the concerns and needs of a target audience. Further, the model must demonstrate the same patterns of behaviour as the real system, and need only be complex enough to meet this objective. If the model is too complex it can become unusable to those who need it most.With this in mind, SUPASIM has been developed for the practical metallurgist requiring only laboratory flotation rate data as input. Some 35+ successful plant simulations have been completed since 1985. The approach of SUPASIM is to characterise an ore, organise information in an understandable way and add structure to the complex flotation situation and hence support the metallurgist to interpret the relationship between variables and optimise the flotation process.The paper describes the basis on which the model was developed and sets out to provide an insight into interpreting laboratory flotation kinetics and their physical meaning in a production plant and the influence floatable gangue has on float performance and plant design. A case study illustrates how the ratio of slow floating mineral to gangue can influence circuit design and improve recovery on a plant scale.INTRODUCTIONThere is an enormous amount of useful data in the results of a laboratory scale rate test. Each variable of fraction and rate, for mineral, metal and gangue has a physical meaning in the plant. The link between float kinetics and the plant in respect of recovery, grade, pulp density, pulp flowrate, residence time, number of stages of cleaning and circuit configuration has been established by the author in the process of developing SUPASIM."

Jan 1, 2005

Building off the enthusiasm generated by Credit Suisse First Boston on the potential benefits of an industry-wide effort to market gold jewellery, a group of gold producers, led by Randall Oliphant, CEO of Barrick Gold, decides to investigate the long -term impact of launching a significant marketing initiative to stimulate demand for gold jewellery. The group establishes an international Steering Committee representing producers of differing sizes, members and non-members of the World Gold Council. This Committee comprises representatives from AngloGold, Barrick, Gympie Gold, Kinross, Randgold, and Sons of Gwalia and is supported by the Australian Gold Council, the Gold and Silver Institute, and CSFB. The Steering Committee hires McKinsey to assist it by conducting an independent review of whether investment in a large-scale marketing initiative for gold jewellery would be effective in increasing demand for gold, and ultimately of significant economic benefit of the gold industry. Based on McKinsey?s review* and its own discussions with key stakeholders across the industry, the Steering Committee strongly believes the case for marketing is compelling and sufficiently proven to persuade the industry to undertake a major initiative over the next few years. The Steering Committee, supported by McKinsey, conducts briefings with a range of gold producers to share its findings and to understand producers? perspectives on an industry-funded marketing campaign. The Steering Committee is asking for your support to bring this industry-funded marketing campaign to life.

May 1, 2002

By John Lemke

Current practice for monitoring static pile load tests commonly consists of measuring load and displacement at the top of a pile. This is typically accomplished by monitoring dial gauge movements, line pressure of a hydraulic jacking system, and electronic load cells on occasion. While this testing approach provides useful information for one boundary condition (the top of the pile), a system that measures movement and/or strain along the entire length of the pile can provide additional useful data that can be used to refine pile design. Automated data acquisition systems provide the essential ingredient that can integrate these types of sophisticated instrumentation devices into a standard pile load test program in a cost effective way. This paper provides a general overview of pile testing instrumentation and describes a newly developed chain of instrumentation modules that can be embedded in a pile to gather additional testing information. The new system can measure forces and movements within the test pile synchronously with measurements at the pile top, and the direct application of this system to axial and lateral pile testing is illustrated. This is particularly relevant to the design of ACIP and drilled displacement piles since determination of the reinforcement cage length is important from the standpoint of both seismic design and foundation cost.

Jan 1, 2002

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

By H. H. Schrenk, W. P. Yant, F. A. Patty

"INTRODUCTION In accordance with the outline of investigation described in a previous report 5 of the Bureau of Mines dealing with the use of acrolein for detecting leakage of methyl chloride from unit--type refrigerating systems, the work has been extended to include an investigation of its use in a multiple system, This report gives the results of analysis of samples of the gas from representative units of a multiple system charged with methyl chloride containing approximately 0.9 per cent acrolein by volume, The results furnish a basis for estimating the Warning that would be given in event of leakage. The properties and warning intensity of acrolein have been described in a previous report. 5 ACKNOWLEDGMENTSThis investigation was made at the combined request-of Several Inc., Manufacturers of refrigerating, appliances, and the Roeasler Hasslacher Chemical Co., manufacturers of methyl chloride. Acknowledgment is given to R. M. Major, ,chief chemist of the former firm for arranging the experimental site and equipment; to Arthur O. Haseeneall, owner of the apartment building where the investigation was conducted, for his courtesy in permitting the investigation; and to R. R. Sayers, chief surgeon, Bureau of Mines, and surgeon., U. S. Public Health Service, for suggestions and advice."

Sep 1, 1930

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

By A. v. E. Conradie, I. Nieuwoudt

Comminution and flotation circuits are frequently perturbed by disturbances, such as feed particle size variations, ore hardness and varying mineral liberation, which can have a significant impact on the recoveries and grades. Although advanced control strategies can neutralize many of these disturbances, few such systems have been implemented at present. One reason is that it is only recently that the requisite sensor systems have been developed and used to control froth flotation systems. Another is owed to the complexity of these non-linear interactive systems. In this paper, a plant-wide control strategy is considered, wherein both unit operations have a single overall control objective. The automated design of the controller is based on an advanced evolutionary algorithm viz., Symbiotic, Memetic Neuro-Evolution (SMNE), for developing neural network controllers in a reinforcement learning framework. A rigorous phenomenological comminution and flotation model was used to develop suitable neurocontrollers, which used all possible sensor inputs and available manipulated variables. The neurocontroller managed to identify optimal or near-optimal operating conditions consistently and showed robust performance in the presence of significant disturbances. The results suggest that evolutionary reinforcement learning offers a very competitive approach towards the development of integrated non-linear controllers for mineral processing plants. Keywords: neural networks, control, flotation, comminution, evolutionary reinforcement learning

Jan 1, 2003

A new porphyry copper gold district has been discovered at Goonumbla near Parkes in central New South Wales. Endeavour 26 North is the largest deposit known to date with a possible resource of 166.4 million tonnes at 0.74% copper, 0.12g/tonne gold and 1.7g/tonne silver, using a cut-off grade 0.3% copper. Mineralisation is primarily bornite in the higher grade zones and chalcopyrite in the peripheral lower grade zones. Most of the copper, gold mineralisation is associated with potassic alteration. Two mineralised quartz monzonite porphyry intrusive stages have been identified and these are related at depth to a large monz- onite stock which may have been the source of some of the mineralisation. On the basis of detailed paragenesis studies, the potassic zone can be divided into three symmetric subzones. The low grade inner potassium feldspar subzone is confined to the later intrusive porphyry. The outer potassium feldspar subzone is the most highly mineralised alteration halo due to the focussed superimposition of two hydrothermal cycles which have overprinted intrusive and volcanic rocks. The fringing biotite potassium feldspar subzone reveals alteration minerals which are developed early in the paragenesis. Fracture controlled quartz sericite alteration with low sulphide content, fringes and, in part overprints the potassic zone. The restricted pipe-like nature of the alteration zones and related mineralisation suggests that Endeavour 26 North is repres- entative of a multiphase focussed porphyry copper gold system.

Jan 1, 1986

By J. W. Reynolds

Introduction The Sullivan mine, at Kimberley, B.C., is the principal source of ore for the Consolidated Mining and Smelting Company of Canada, Limited. Current production amounts to about 2,500,000 tons of lead-zinc ore a year. With approximately 1,600,000 feet of percussion drilling and 700,000 feet of diamond drilling being carried on each year, any improvements in drilling practice are important. Testing of new equipment and drill bits is a major function of the Testing Department at the mine. Tungsten carbide bits have been the subject of many tests since 1947 and have been used in operations since 1948. This paper details with the methods of testing and gives comparative data on performance and costs for tungsten carbide bits as compared to steel bits. Operational use of tungsten carbide bits started in April, 1948, and the extent of application has increased considerably since that time. The scale of employment is illustrated in Table I, which also shows other statistics on the use of carbide bits. Up to the present time eighteen types of carbide bits or tipped steel, as made by six different manufacturers, have been tested. In general, one supplier's bits have been used in operations, but some large-scale operational tests have been carried out with other types. The types tried are shown in Table II. To date they have been, the subject of 33 tests, covering the destruction of 804 bits over an observed footage of 42,586 feet.

Jan 1, 1951

The newly implemented mineral law framework exacerbated the need to clarify the roles and responsibilities of mine and land surveyors in the preparation and registration of plans and diagrams. The main concern is that survey tasks may be performed by persons who are not considered competent under the different laws. The methodology used was to analyse historic and present legislation on the issue in order to formulate a narrow interpretation of the current requirements. The major findings are tabulated to present a summary of who is responsible for which areas of survey.

Jan 1, 2010