Search Documents

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011

By C. H. Stockwell

"The Precambrian rocks of southeastern Manitoba contain a great variety of mineral deposits, including gold, chromium, copper, nickel, lithium, tin, beryllium, tungsten, and molybdenum. Although considerable interest has been shown from time to time in each of these types of deposit, production to date has been almost entirely in gold. This has had a value of about $26,000,000 and has been derived chiefly from the San Antonio mine, with lesser amounts from the Central Manitoba, Gunnar, Beresford Lake, Ogama-Rockland, Diana, and other properties.Most of the deposits lie within volcanic and sedimentary rocks or within basic intrusions cutting these rocks. These favourable rocks occur in several areas, which have been given local names and are separated from one another by large bodies of granite (Fig. 1).In general, the several areas are characterized by different types of mineralization. Thus, the Rice Lake-Beresford Lake area contains numerous gold deposits and has yielded almost all the gold production to date; the Maskwa River, Euclid Lake, and Oiseau River areas are, on the whole, characterized by deposits of chromium, copper, nickel, lithium, tin, and beryllium; and in the West Hawk Lake area there are deposits of gold, tungsten, molybdenum, and lithium.As might be expected in a district containing such a variety of mineral deposits, the structural conditions controlling their deposition also vary greatly. It is, accordingly, convenient to discuss the structural geology and mineral deposits of each of the more important areas separately."

Jan 1, 1954

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By Kirstin Girdner, Tom BoBo, Brian Norton, John Kemeny

Split Engineering is a truly customer oriented company dedicated to providing quantified fragmentation information of the highest integrity to enable process management and control. Technical decisions, blasting costs, operational efficiency and productivity and equipment performance can all be related to optimum fragmentation. In the past, the lack of an easy, non-disruptive, economical measuring technique has meant that, in most cases, rock fragmentation has not been defined in quantitative terms. Now, the Split-Desktop@ software provides an economical alternative to manual sampling and screening and an objective measure rather than subjective qualitative estimates. This workshop will present the latest features of the Split-Desktop@ software and show users how to quickly get quantifiable results from their blast fragmentation. A step-by-step demonstration will display the software’s flexibility, user-friendly options, and ease of use. Outlining where other mines have benefited from using the Split-Desktop@ software will provide insight to a wide range of software uses and potential applications like creating a database of geologic zone specific post-blast fragmentation information, underground draw point monitoring, stockpile, leach pile, and waste dump size measurement and monitoring, as well as many other applications.

Jan 1, 2000

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

By Thomas Fraser

About 24 per cent of our total production of bituminous coal is used in industrial power plants. As regards fuel conservation, therefore, the recovery of unburned fuel from furnace refuse presents interesting possibilities. Considerable attention has been given to this problem in the past, but because of the comparatively low initial cost of power plant fuel in the pre-war period little progress, has been made in this direction in the United States. Because of the higher price of coal in Europe more attention has there been given to the problem. In Germany a process has been developed for separating unburned coal in refuse by using an electromagnetic separator In the United States the use of mechanical stokers enabled low-priced screenings of high ash content to be used, so that even with relatively high percentages of combustible material remaining in the refuse, the loss in money is not excessive. If the price of screenings returns to the pre-war level around $1.00 per ton the process proposed here will probably not be especially interesting, except where the freight charges are very high. However, if the price of delivered coal continues high, such a process should result in considerable saving. The cost of continuous operation of such a refuse treating plant should not exceed 75 cents per ton of fuel recovered.

Jan 1, 1921

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013

By Jan E. Nesset, Phillip J. Mackey

"Studies have shown that there is a correlation between commissioning and start-up time, i.e. time to reach full plant design capacity, and the degree of innovation and technical/engineering uncertainty in the project design. The paper describes the types of start-up curves for plants according to the level of technology or uncertainty in the process design. The need to properly describe and understand the commissioning and start-up time is examined using these curves and the importance on project success is highlighted. A number of case histories of recent mining and metallurgical projects are also reviewed. Finally, the paper reviews how to better assess the level of start-up uncertainty associated with a project and makes suggestions for decreasing the commissioning time due to technological risk.INTRODUCTIOThe start-up of a new mining and metallurgical facility, a much anticipated event, is a critical step in the life of such a project. Achieving a successful start-up and reaching the design capacity on-time requires careful planning, a thorough understanding of the key technological and engineering components involved and a well-trained and adequatelystaffed start-up crew. In this paper, some of the aspects related to start-up of a mining/metallurgical project will be explored, and in particular, the impact of the technology component will be examined. In order to illustrate this, a number of case histories based on recent mining and metallurgical projects will be discussed. Ways of assessing and understanding the uncertainty associated with technological issues related to start-up of a mining and metallurgical plant will also be examined.The history on mining and metallurgy is full of success stories of great mines and mills that are now considered “company makers” (well known examples of such successes include the Horne mine for Noranda which had a 1 year start-up in 1926-27, the Dome mine for Placer Dome, the Grasberg deposit for FMI in Indonesia). Less well documented are specific studies relating to plant start-ups and what constitutes a success or a failure, however there are a few notable references in the literature and these will be reviewed."

Jan 1, 2003

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By R. J. Heemstra

A continuous flowing paper electrophoresis cell was used to separate petroleum and petroleum extracts into characteristic patterns. The electrophoresis of Bachaquero, Lagunillas, Boscan, and Gibson petroleums in nitro-benzene and acetic acid-based electrolytes was investigated. The extent of separation in the patterns was studied by measuring the metal and porphyrin contents of the effluents. Qualitative separations were achieved in some systems, whereas either system demonstrated only a high degree of electrophoretic migration.

Jan 1, 1967

By J. M. Sands

Production of oil in Oklahoma during 1927 amounted to 273,256,900 bbl. (Table l), an increase of nearly 100,000,000 bbl. over the previous year. All of the major fields declined with the exception of those of the Seminole district which produced 136,105,000 bbl., almost one-half of the total production of the state. Because of this large new production, most of the development in the state during the year took place in that district. The Seminole City pool located in T.-9-N., R.-6-E., was the first of these pools to be developed. The Indian Territory Illuminating Oil Co. brought in the first well in this field in March, 1926, for 1100 bbl. This well is located in Sec. 24-T.-9-N., R-6-E., and produced from the Hunton lime reached at depth of 3900 ft. The first Wilcox production was developed by the Independent Oil & Gas Co. and R. S. Garland in Sec. 26, T.-9-N, R-6-E. This well was being drilled for production in the Hunton lime but was dry in this horizon and was deepened to the Wilcox sand in July, 1926, and at the total depth of 4069 ft. developed a maximum production of 8000 bbl. daily. It held up in wonderful manner and was the cause of not only the development of this pool but the prospecting of the whole district for the Wilcox sand. This led to the discovery of the other major pools in that district. Seminole City pool reached a peak production of 264,500 bbl. on February 22, 1927, and slowly declined so that by December it had a daily average of 56,200 bbl. from 321 wells. The second pool in this district to be discovered was the Searight pool which was discovered by F. J. Searight et al. in Sec. 33, T-10, R-6, in April, 1926. The first well was drilled to the Hunton lime encountered at 4115 ft., and came in for 1300 bbl. daily. During August, 1926, the second well was drilled on the same farm through the Hunton lime to the Wilcox sand which was encountered at 4360 ft. It came in for an initial production of 4000 bbl. daily. This started active drilling in this field for the Wilcox sand. The field had a peak production of 40,621 bbl. on June 15, 1927, and declined to a daily average of 22,300 bbl. from 73 wells during December.

Jan 1, 1928

By William J. Rothschild

Ground water at construction sites can be controlled by properly placed wellpoint dewatering systems. Care must be taken in planning cofferdams to have adequate space for and access to pumps, headers and the points. A most important part of dewatering is protection of adjacent structures from movement. A checklist gives items to consider in bidding.

Jan 1, 1984

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.

By Will B. Jamison

An ignition detection and suppression system was developed under the scope of this contract. The objective of this machine mounted system was to detect flames caused by frictional sparking from the cutting bits of a continuous mining machine and to suppress it with sufficient speed to prevent the development of an explosion, and to keep the flame from harming the machine operator.

Jan 1, 1976

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By C. J. A. Mcewan, C. M. Rice

The Rosita Hills contain rich, vein- and breccia pipe-hosted precious metal deposits. Volcanic activity occurred in two cycles - an early, mainly andesitic cone-building phase that terminated in the formation of a caldera and breccia pipes and a later phase characterised by trachytic lavas and dykes, rhyolite domes and lamprophyre dykes. Alteration consists of weak propylitic and argillic and, locally, intense advanced argillic, K-feldspar sericitic and silicic types. Marked trace-element depletions (Rb, Sr, Zn, Mn) are associated with K-feldspar-sericitic alteration and with advanced argillic alterations, whereas enrichments (Pb, Ag) are associated with K-feldspar-sericitic alteration. Gold distribution is highly localised and is controlled by breccia pipes and a caldera ring fault; it is not related to district scale alteration. In general, the geochemical and alteration patterns are complex, but they are clearly influenced by linear structures, the caldera ring fault and breccia pipes. Pipe-hosted Au-Ag and vein-hosted Ag mineralisation are associated, respectively, with early andesitic and late, post-caldera rhyolitic activity. The pipe-hosted and, especially, the vein-hosted mineralisation show affinities with adularia-sericite-type epithermal deposits

Jan 1, 1991

By D. M. Abbott

The requirements of the International Mineral Property Valuation Standards Template (IMVAL Template) (includes Petroleum), 4th edition of April 14, 2021, are based on six principles: 2.1.1 competence, 2.1.2 materiality, 2.1.3 transparency, 2.1.4 objectivity, 2.1.5 independence, and 2.1.6 reasonableness. The IMVAL Template describes “reasonableness” as, “The Valuer must ensure the Reasonableness of the Valuation. Any Valuation, assumptions applied, and any method relied upon should be reasonable within the context of the purpose of the Valuation and the Basis of Value. A method applied to the subject Mineral Property should be within the expected capability and consideration of an assumed likely buyer or lessee of the property.” The IMVAL Template’s Guidance 3.6 on Reasonableness states, “The test of Reasonableness is to consider what appropriately qualified and experienced Valuers, acting reasonably, would conclude in the circumstances. The Valuer must form an opinion that is reasonable in the circumstances, that is, what a Valuer believes is rational and plausible in the circumstances and would be viewed as such if considered by other appropriately qualified and experienced Valuers with the same information and at the same time.” Finally, the IMVAL Template’s Definition 4.26 states Reasonableness “[m]eans that other qualified and experienced Valuers with access to the same information for the same Valuation Date and Basis of Value would consider the Valuer's estimate of Value to be within a reasonable range.”

Mar 2, 2022

By T. Nishi, D. Teguri, K. Saitoh

In recent years the requirement for high carbon ferro-manganese (HCFeMn), which is the key product of our company, has increased due to bullish demand for steel products. In our Tokushima works, we have 2 closed types of electric furnaces (1F and 2F), with which we are manufacturing HCFeMn. In order to meet the increase in demand, we made various modifications to these furnaces and we tried to increase the furnace operating loads. Especially for 1F, we deepened the furnace. In this paper, we report the results of this modification. The operational situations of the above-mentioned two furnaces are different because they have different individual profiles. As for 1F prior to modification, the depth of the furnace was one meter shallower than2F, because 1F was designed for the manufacturing of SiMn. On the other hand, our Tokushima works specialized in HCFeMn 14 years ago. However, the profile of 1F was not optimized for HCFeMn. In comparison to 2F, 1F was more difficult to stabilize due to the smaller tolerance for the adjustment of the electrode length, the metal / slag level, and the coke-mixing ratio. We deepened 1F by 770mm by disposing of the furnace rolling mechanism. We consequently achieved a 10% increase in production capacity. This meant the operating load was enhanced from 24.5MW to 27MW, the furnace became more stable and the tapping speed of both metal and slag increased, all which made the tapping easier than before.

Jan 1, 2007