Search Documents

By Robert T. Mann

This paper is one of a series being prepared for and published by the United States Bureau of Mines on the quarrying, crushing, and grinding of limestone for cement manufacture. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total coats. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. B. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1933

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By R Stosch, D Lohberger, J Rodler, E Schnell and A Bassler, H Ramseier

In the last two decades three-dimensional (3D) computational fluid dynamics (CFD) simulations have become an important tool in engineering sciences. More recently, the safety requirements in underground railway stations have increased with regard to incidents. For this reason, existing underground stations (eg Munich, Strasbourg and Berlin) are being equipped with smoke extraction facilities to protect passengers from smoke and visibility impairment in the event of fire. In addition, designs of planned underground stations (eg Karlsruhe, Doha) also include these facilities.For the commissioning of ventilation engineering systems with complex structures, the functional testing of the whole technical installation are important, as are the acceptance tests of ventilation and equipment parts. This functional testing includes not only the technical inspection of the equipment but also the acceptance measurements of the capability of the equipment and the execution of hot- or cold-smoke tests to confirm the effectiveness of the ventilation system.Due to the fact that the overhead contact line and other sensitive installations were already installed in the tunnel roof at the time that smoke tests were proposed, hot-smoke tests with fire loads up to a maximum of 1 MW could only be executed. Therefore, the evidence of the attainability of the safety objective had to be provided computationally in this special case with a fire scenario of a heat release of 10 MW using CFD simulations.This paper presents the interplay between the results from acceptance testing and smoke tests and the use of 3D CFD simulation and virtual reality using the example of Allmend station, which was repositioned underground and is part of a new section of track from Lucerne railway station to Kriens in the Zentralbahn network. The steps of the verification and validation of the computer model are presented with the real tests and measurements.CITATION:Stosch, R, Ramseier, H, Lohberger, D, Rodler, J, Schnell, E and Bassler, A, 2014. Safety in underground railway stations – an example of the interplay between testing and 3D computational fluid dynamics simulation, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 103–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Using Mineral Maps to Rank Potential Processing Behaviour

Sep 13, 2010

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By H. Rozovsky

This paper deals with the large iron ore concentrating plant owned by the Iron Ore Company of Canada. The plant is part of the Carol Project, which is being developed in the Wabush area of western Labrador. The mining and milling operations were officially opened in July of this year. The handling of fine material has always been considered a serious operational problem. The crushing, grinding and sizing of 50,000 tons of iron ore per day, in a dry state, could present sizeable problems in maintenance and orderliness. The operation, as a whole, embraces many recent developments in the iron ore industry. Mining operations include the latest techniques of jet piercing and blasting. Primary crushing involves a single crusher, which handles the complete production. Grinding of the ore includes the latest concepts of dry autogenous grinding in air-swept mills. The actual concentration of the ore is per-formed, in the wet state, by the use of spiral concentrators, with provision for possible flotation or magnetic separation, if required. The upgraded concentrates are either stored or pelletized, prior to shipment by rail to Seven Islands.

Jan 1, 1962

Jan 1, 1962

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By L O. Filippov, Q Dehaine

Variographic analysis, a classical tool from the Theory of Sampling (TOS), can address practical situations with multiple variables; however, its application has very often been limited to one variable at a time. Recent developments have shown the benefits of using multivariate approaches for variographic characterisation of a set of variables instead of considering individual variables sequentially. Among these approaches, the multivariogram has been revealed itself to be a powerful tool when the overall time-variability of a process must be summarised in terms of a large set of properties (variables) to assess its true global variability. However, even when choosing the properties of interest carefully, the resulting global variance obtained with this approach may be very high. In particular, some variables that contribute to a major proportion of the global (multivariate) variability could be less important for the process performance than others having a lower variability. To address this issue, a new approach is proposed, combining the multivariogram with process modelling and multivariate data analysis methods such as partial least squares (PLS) regression from chemometrics. An example from the mineral processing industry is presented, for which the process performance could be linked to key process variables (sensor data) using the PLS regression. Once introduced in the multivariogram equation, PLS model parameters (loading-weights or regression coefficients) can be used to weigh the variables according to their relevance for the process. In addition, this also permits characterisation of process performance variability with time using only the process input variables and a weighted metric according to the PLS regression model. Ultimately, this method helps to find an optimised sampling procedure in terms of frequency, sampling mode and number of increments according to the actual overall process performance. This approach has potentially many applications in the mining, feed and food, pharmaceutical or any other industry for which it can be used to reduce risks and ensure a better use and management of resources.CITATION:Dehaine, Q, Filippov, L O and Glass, H J, 2017. Optimising multivariate variographic analysis with information from multivariate process data modelling (partial least squares regression), in Proceedings Eighth World Conference on Sampling and Blending , pp 381–390 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By M. M. Zarnan

This paper presents the results of s study involving characterization of ground subsidence of abandoned lead-zinc mines in northeastern Oklahoma. Two coordinated efforts were undertaken: (1) collection and analysis of available data such as driller's logs, geologic cross-sections, structure contour naps and stratigraphic sections, and (2) development of a numerical (finite element) technique for prediction of collapse and mine subsidence. An in-depth analysis of a major collapse in the region was conducted. The factors which contributed to this collapse were identified.

Jan 1, 1989

Experiments in the bolting of a mine roof were commenced at Elrington Colliery on the South Maitland Coal Field early in 1949, following the appearance of an article in the American publication, "Coal Mine Modernisation Year Book" 1948. Prior to this, although bolting had not been used in the maintenance of satisfactory roof conditions, the principle of roof bolt anchorage had been illustrated in instances such as the hanging of a trolley locomotive power wire using an expanding shell type of bolt anchorage, or the insertion of an eye bolt with a split and wedge, as used to suspend a rope block over a winze being sunk in a metalliferous mine.The experiments at Elrington Colliery were the first efforts in this country to supplement the work of timber supports under a mine roof with systematic placement of roof bolts.Following the series of experiments at Elrington, full scale bolting was commenced at that Colliery in a trackless mobile section in April, 1950.The obvious success of the system at Elrington indicated that it might also be a success in the support of weak roof strata immediately overlying the workable section of the Victoria Tunnel Seam at John Darling Colliery.The system was commenced at John Darling Colliery in April, 1951, in one mechanical section on the Victoria Tunnel Seam, and the scope was gradually widened until by December, 1952, ail'six mechanical units then operating on this seam were working under bolted roofs.

Jan 1, 1954

By Peter B. Dowden, David T. Cass

A shield on a tunneling machine has two basic purposes. Firstly to provide temporary support in unstable ground, maintaining the integrity of the bore and protecting the operators, and secondly, in conjunction with other sealing devices, to prevent the ingress of water. In any specific tunnel, unstable ground and water may or may not occur together. Further, there are a number of different ground behaviors that may be termed unstable and these must be defined in order to determine the most suitable type of machine. Beyond the shield itself, the cutterhead and the mucking system design are critical in successfully traversing difficult geology. In any but the shortest tunnels, variations in the geological conditions and the requirement of an acceptable advance rate can impose increasing degrees of sophistication in the machine design. In this paper we will review current designs of shielded type machines and their application, and discuss new developments which blend hard and soft ground tunneling technology. We will also indicate that in some conditions, although first impressions seem to favor a shielded machine, in fact an open gripper TBM may be the wisest choice.

Jan 1, 1991

By P. Massacci, F. La Marca, G. Bonifazi

Certain deposits of incoherent materials which are near the surface and exploitable by open-pit mining may be characterized in real time before they are mined through an analysis of ground-surface imagery. If the slice to be stripped is not overly thick, in fact, surface texture and color properties may be extrapolated to its entire thickness. Image analysis techniques to process ground surface images acquired in situ(or in the laboratory shortly after their acquisition) which yield pattern vectors representative of RGB color component distributions and HSB texture parameters have been developed. The techniques were applied to a mineral sandy ore deposit containing three different lithotypes. Geostatistical analyses showed that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multi-barycenter classification algorithm. Such in situ image-analysis procedures open the way to the proper selection of the ore to be mined, or the proper way for run of mine (r.o.m).processing, or the appropriate blend to be processed before or at the same time as the mining process itself is enacted.

Jan 1, 1999

This paper discusses the history and development of the system and the benefits that are being gained for Yabulu from Solar Drying. Following the end of mining of the local Greenvale and Brolga nickel deposits, QNI Yabulu Refinery is dependent upon imported ore from over 15 different mines in New Caledonia, Indonesia and the Philippines.

Jan 1, 2003

By Peter Wells, Adrian Sabau, Turgut Yalcin

"The nickel ores of Sudbury contain substantial amounts of the gangue mineral pyrrhotite (Fe7S&) which causes certain diflculties in the milling of these ores. This paper proposes a process called “magnetoflotation” as an effective means of dealing with pyrrhotite. The method reduces the pyrrhotite content of concentrates by applying a magneticjield on the path product as it leaves the flotation cell.Successful performance of magnetoflotation requires the optimization of several variables. In this study, three of the variables (air flowrate, collector concentration, pother concentration) were investigated by Box- Wilson experimental design, and others (magnet speed, grind size, pulp density, flotation time) were examined individually. The process was tested on a Falconbridge nickel ore, assaying 1.92% Ni, and under the best operating conditions, a concentrate was obtained with 13.56% Ni grade and 74.32% recovery in a single step. Further improvements to grade and recovery were possible by cleaning and scavenging. The same ore was also tested with conventional methods for comparison, and results indicated that magnetoflotation performed better.INTRODUCTION“Magnetoflotation” refers to the process of carrying out magnetic separation and flotation simultaneously within the same device, and is intended to prevent magnetic minerals from reporting to the froth products while non-magnetic minerals are being floated. Typical cases where this method might be beneficial include the processing of magnetite and nickel ores. Its use on magnetite ores has been reported elsewhere [Yalcin, 1992; Yalcin, 19931. This paper describes its application to nickel ores, more specifically to the nickel ore of Falconbridge Limited in Sudbury."

Jan 1, 1999