Search Documents

By Andre Zingano

The objective of this paper is to compare the behaviors of different types of roof bolts: (1) One-Step Bolt (OSB), (2) Fully grouted Bolt (RB), (3) Combination Bolt (CB), and (4) Torque tension Bolt (TB). Two dimensional numerical models were built for both bolted and unbolted roofs. The geological sequence and rock properties used in the numerical models represent the typical roof condition for Pittsburgh coal seam. Using the unbolted roof as a base case, a comparison is conducted by monitoring the roof vertical displacement at the center of the entry and at the bolt positions, the axial force in the roof bolts, and stress distribution in the bolted area. The grout/rock interface is assumed to be perfect. The estimated roof displacements showed that the differences among the four types of roof bolts are small. The major differences are in the shear stress at the grout/rock contact and in the shear stress along the immediate roof bedding interface as well as in the bolt axial stress. There is less axial stress for the OSB compared to RB and CB as the diameter of the OSB is much bigger and the contact area between grout and rock is twice as large as for RB and CB. The higher strength of the OSB contributes to keep the bedding planes in the roof closed.

Jan 1, 2007

By D. Eugene Rannels, Yu-Chen Lee

"Lee, Yu-Chen, and D. Eugene Rannels. Alveolar macrophages modulate the epithelial cell response to coal dust in vitro. Am. J. Physicl. 270 (Lung Cell. Mol. Physiol. 14): L123-L132, 1996.-The response of the alveolar epithelium to coal dust exposure is poorly understood. Coal or other dusts may act on the epithelium directly or indirectly through nearby alveolar macrophages (AM) that produce cytokines and other soluble products. AM and type II pneumocytes (T2P) were thus exposed to dust in coculture to evaluate their possible interactions. Anthracite coal dust PSOC 867 increased synthesis of extracellular matrix (ECM) components by T2P. AM alone did not produce ECM. Similarly, coculture ofT2P with AM (3.75:1) had little effect on epithelial ECM synthesis. In contrast, coculture ofT2P with AM significantly increased PSOC 867 effects on T2P rates of ECM synthesis, ECM fibronectin content, and T2P levels of fibronectin mRNA. AM-conditioned medium did not change the PSOC 867 effect on T2P. Neither control nor PSOC 867-treated AM on Falcon culture inserts (0.45-µm pore size) over T2P stimulated ECM synthesis by either untreated or dust-exposed epithelium. Thus AM-mediated changes in ECM synthesis by PSOC 867-treated T2P require close cell-cell interactions, suggesting a role for cell-cell contact or for short-lived soluble mediators of the AM effects. DEVELOPMENT OF PNEUMOCONIOSIS, a chronic disease of coal workers that results in pulmonary fibrosis and low lung compliance, is associated with inhalation of mineral or coal dust in the work place (14). Although the pathology of pneumoconiosis has been studied extensively, cellular mechanisms that cause changes in lung structure and function are not fully understood. Particulate matter that enters the respiratory system distributes according to size, with larger particles being removed in proximal airways. Dust components of small size may enter distal alveolar region, which is populated by two types of epithelial cells, type I and - type II cells, and by alveolar macrophages (16). Each of these cell types may interact with inhaled particles, but only the effects of coal dust on alveolar macrophages have been studied extensively. Less is known regarding the response of the alveolar epithelium, or of effects on epithelial cell-alveolar macrophage interactions, in the dust-exposed lung.Function of the alveolar epithelium is well known to be influenced by the underlying basement membrane, or extracellular matrix (28). Alveolar epithelial cell extracellular matrix interactions, which may involve modulation of cell migration, attachment, or differentiation (17), are reflected in type II cell morphology, metabolism, secretory activity, hormone responsiveness, lamellar body content, and gene expression (21). The extent to which basement membrane modulates differentiation of the overlying epithelium is determined by both molecular composition and three-dimensional structure of the matrix. Type II epithelial cells in vitro synthesize, secrete, assemble, and degrade a variety of basement membrane components, including laminin, fibronectin, type IV collagen, and thrombospondin (22, 27). How expression of these components is regulated, directly or indirectly, upon exposure of the alveolar epithelium to injury by coal dust or by other particulates remains to be resolved."

Jan 1, 1998

By Lars Richter, Franz-Werner Gerressen

"The Eglinton Crosstown Line was conceived as the Eglinton Crosstown LRT, a partially underground light rail line, announced in 2007 as part of the Transit City plan, which included the implementation of six other light rail lines across Toronto.There were 43 stops planned for the Eglinton Crosstown LRT, 13 of which would be underground . For those underground stations a lot of specialty foundation works needed to be carried out. King piles, soldier piles with lagging and secant piles were mainly required fulfilling the tasks of installing the retaining wall system.The paper will focus on the original design and alternative solutions, discussing the benefits and limits of these. It will also explain the installation process in general as well as some specific features related to specific site conditions, e.g. limits in installation depth, soil characteristics etc. The required equipment will be explained showing the benefits and limits.INTRODUCTIONThe Eglinton Crosstown project is a 19-kilometre LRT line that will bring much needed relief to the transit woes of Torontonians. Traversing the city in an east-west slice across the midtown artery of Eglinton Avenue, the Crosstown rail line involves a combination of 15 underground stations and 10 atgrade surface stops. It is one of the largest transit infrastructure projects under way in North America today. Aecon has joined partners ACS Infrastructure Canada, Ellis Don, and SNC-Lavalin to form Crosslinx Transit Solutions (Crosslinx).As with many of today’s mega public transportation projects, the Crosstown LRT follows the Public- Private Partnership (P3) model. Aecon is an equal partner in the $5.3-billion Crosslinx consortium to develop the Eglinton Crosstown LRT project in Toronto. Upon the LRT's completion in 2021, Metrolinx, the region’s transit authority and also the project client/owner, will turn to the Toronto Transit Commission (TTC) to operate it. The impact of this highly anticipated LRT line on commuters in the Greater Toronto Area (GTA) is expected to be dramatic and immediate once the first train leaves the station five years from now. In fact, Metrolinx is estimating that within its first 10 years of service, the Crosstown line will be carrying 5,500 passengers per hour (in peak direction) and making 100 million passenger trips annually."

Jan 1, 2017

By Randy Settgast, Daniel Moos, Hyunil Jo, Ghazal Izadi, Christine Baba

"Analyses of production logs of multiply fractured horizontal wells in unconventional plays show that only a small percent (~30%) of perforation clusters contribute to production. We present in this paper one possible approach to mitigating this problem, based on use of a fully 3-D numerical model of fracture propagation through a heterogeneous medium, by studying the influence both of spacing and of perforation friction on the initiation and propagation of simultaneous hydraulic fractures from a horizontal wellbore. The results indicate that while limited-entry perforating can help to equalize the lengths of fractures simultaneously growing from multiple clusters, it cannot equalize their widths. Both fracture width and fracture length can be equilibrated by combining non-even cluster spacing with limited-entry perforating. This has obvious benefits as it allows equalized placement of proppant across the entire series of perforation clusters, resulting in similar fracture widths and conductivities which enhances the likelihood that all clusters will contribute equally to production.INTRODUCTIONThere is substantial evidence from production logs and other information that during the hydraulic stimulation of horizontal wells, not all perforation clusters within a given stage will produce. One possible cause is the interaction between the hydraulic fractures emanating from each perforation cluster. Typically fractures created at the outer perforation clusters create “stress shadows”, i.e. increases in compressive stress in the minimum principal stress direction, which limit the growth of fractures growing from interior clusters; this is confirmed by modelling [1, 2, 3]. An example of this can be seen in Figure 1 which shows the final configuration of simultaneously propagating fractures from multiple, evenly spaced clusters when there is no perforation friction. The inner fractures are substantially shorter, reproducing the results by Bunger and Peirce [3]. The inner fractures also have substantially smaller widths.One approach to equalize the growth of simultaneously propagating fractures from a horizontal wellbore is by using limited-entry perforating as a method to equilibrate the flow rates into each of the different perforation clusters. Perforation friction is caused by the finite diameter of the entry points into the formation, and leads to a pressure drop across each perforation which is proportional to the flow rate squared. Fractures that take more fluid have a higher fluid velocity through the perforations than fractures receiving less fluid. This causes a larger pressure drop between the wellbore and more rapidly growing fractures, compared to the same pressure drop between the wellbore and the fractures that grow more slowly. Because pressure within the wellbore is approximately the same at each entry point, the larger pressure drop leads to less pressure being delivered to rapidly growing fractures, thereby decreasing their ability to propagate and reducing the amount of fluid they are able to receive. Because the mass rate of injection into the wellbore is constant, this forces more fluid into the fractures that were propagating more slowly, increasing their growth rate. It also increases the pressure required to drive fluid injection. The balance of these effects makes the system largely self-regulating and delivers more balanced fracture growth. While this effect is well known, it is often neglected in current numerical models."

Jan 1, 2015

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010

By G J. Lyman

In sampling a process stream, conventional sampling theory deals only with the variation of the analyte content and neglects the impact of the variation in the mass flow on the sampling variance, whether the sampling regime is time-based or mass-based. This is an obvious simplification of the real state of affairs and it is worthwhile to study this impact via simulation.With a facility to simulate large (long) random functions having some thousands of points in the function and the ability to impose covariance functions on the mass flow and analyte variations, such a study is possible. It is also possible to evaluate the impact of correlation between analyte content and mass flows.This paper describes a limited study of the variance increase due to mass flow fluctuations over the usual sampling variance due to analyte variation during the sampling period. The bias in the sampling result is determined for specific modes of correlation. Simulation methods are used as they are the only means by which a sampling result can be compared to the true assay for the lot; in the physical circumstances of mineral process analysis, it is never possible to determine the true process stream assay.CITATION:Lyman, G J, 2017. The impact of the weighting error, in Proceedings Eighth World Conference on Sampling and Blending , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Olaf Andersen

Crucible melt extraction yields short metal fibers with eqivalent diameters as low as 50 µm from almost arbitrary metals and alloys. Highly porous components can be made from such fibers by suitable deposition and sintering methods. This technology is being developed at the Dresden based Department of Powder Metallurgy and Composite Materials of the Fraunhofer Institute for Manufacturing and Advanced Materials (IFAM) and has been applied to gold alloys and iron-base alloys containing small additions of precious metals. From the manufactured gold fibers, sintered structures were made for decorative applications. Additionally, it was found that due to rapid solidification during the fiber formation, precious metals can be finely dispersed in ironchromium- aluminum (FeCrAl) and FeAl20 alloys. Good catalytic activity at elevated temperatures was found in compositions containing 3 wt.-% Ce and 0.5 wt.-% Pt.

Oct 1, 2003

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The performance of two large-capacity ventilation systems was compared through tests conducted in a large dead-end heading at a pilot oil shale mine in Colorado. Sulfur hexafluoride (SF6) tracer gas was used to measure the performance of the two systems: a free-standing jet fan and a reversible fan with rigid duct. The tracer gas was used to simulate the production of mine air pollut-ants, including blasting pollutants, hot diesel emissions, free methane from surrounding strata, and methane desorbing from muck piles. The test room was 55 ft wide, 30 ft high, and 320 ft long. The performance of the two fans was similar, but the jet fan used less power. The tests showed that either system could provide effective ventilation during oil shale mining.

Jan 1, 1986

By W. G. Davenport

Chapter 1 showed that flash smelting is a key step in extracting copper from sulfide ores. It also showed that there , are two versions of flash smelting: (a) Outokumpu flash smelting, which uses oxygen-enriched air blast and injects dry feed downwards into a hot furnace (b) lncoflash? smelting, which uses industrial oxygen blast and injects dry feed horizontally into a hot furnace. This chapter describes Outokumpu flash smelting.

Jan 1, 2001

By C Jenkins, J Jasper, Y Suryaputradinata, S Lozyk, M J. Hartmann

The primary objective of mining companies is to function as a profitable business by delivering products that fit customer requirements in a safe and sustainable manner. Optimum resource utilisation is a critical focus area to achieve this objective, and the long-term sustainable business performance of a mining company is determined by the extent to which this is achieved. Technology improvements and/or new technology development could improve resource utilisation. However, adding new projects to a Brownfield operation carries risk. Overall project schedules, tie-in schedules and safety risks normally receive adequate attention, but the introduction and integration of new technology to a Brownfield site also carries the significant risk of failure to achieve design performance (quality or throughput). This risk must be addressed via rigorous design phase risk assessments and piloting. Post commissioning, the effective metallurgical integration of any new technology/circuit/process plant into an existing process plant calls for critical assessment, through circuit performance testing, and optimisation to ensure alignment with design criteria. In addition, this approach provides clear focus areas for further optimisation of the new plant and additional opportunity for overall plant optimisation. Roy Hill recently navigated this process successfully, and this paper provides feedback on the journey that led to improved resource utilisation.

Nov 8, 2021

By Ellsworth R. Spencer

An assessment of U.S. western hardrock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hardrock mining machines. Of the operators, 96% had daily noise doses that exceeded the U.S. Mine Safety and Health Administration?s (MSHA) permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214% and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jackleg drill. These results will be used to help prioritize noise control development by NIOSH and other partners.

Jan 3, 2010

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

THE present article makes no claim to be exhaustive, since it cannot contain all the knowledge which scientists and manufacturers of the compounds of the rare earths have gained. The following notes are, therefore, simply an attempt to ascertain andclearly record the occurrence, properties, and uses of the more important of the rare earths, with a special reference to their commercial values and the industries based upon them.HISTORYIt was the mine manager, Gcyer, of Stockholm, who, in 1788, first drew attention to a black mineral which had been found in a quarry near Roslagen, in Sweden. In 1805 Klapproth received some specimens of this mineral, which he declared to be a newmineral. Subsequently Gadolin, professor of chemistry at Abo, analyzed the same mineral, and determined the presence of an unknown earth resembling alumina and lime. He named the mineral ytterbite, and afterwards gadolinite. Klapproth has alsothe merit of having detected (1804) another rare earth, which he named ochroit-earth, found in the Bastnas mine, near Riddarhyttan, in Wcstmannland, Sweden. Curiously enough, Hisinger and Berzelius simultaneously ascertained the existence of the same...

Jan 1, 1909

By Howard Lum, Sergio Valles, John Bednarski, Gordon Enas, Jay Arabshahi

"Water drawn from the Sacramento-San Joaquin Delta provides water supply to 66 percent of California’s population and supports the state’s agriculture industry. The existing through-Delta water system is outdated and unreliable with environmental risk to some fish and wildlife species. The Bay-Delta Conservation Plan (BDCP) has been established to environmentally retrofit and modernize California’s water delivery system through the Delta by restoring habitats, constructing new diversion points in the north Delta and providing a means to transport water supplies under the Delta, rather than through sensitive natural channels.Under BDCP, the Delta Habitat Conservation and Conveyance Program (DHCCP) has developed several alternatives to convey water from the Sacramento River in the north to the existing pumping facilities in the south Delta through an isolated conveyance system. The new conveyance system would become an integral part of the State Water Project (SWP) and the federal Central Valley Project (CVP) by transporting water to the export pumping plants for each of these projects. The DHCCP is managed by the California Department of Water Resources (DWR), while state and federal water contractors provide technical support to the program.The initial conceptual study efforts on the overall program commenced in 2007 and examined various options for the proposed conveyance system. Several conveyance alternatives were analyzed at that time. The Conceptual Engineering Report published on Oct. 1, 2013 identified the modified pipeline/tunnel option (MPTO) as the preferred alternative to be included in the BDCP environmental documents. MPTO includes three river intakes and pump stations along the Sacramento River, various sizes of pipelines and tunnels, junction structures and two forebays that are capable of delivering up to 4 million gpm (9,000 cfs) from the Sacramento River to the SWP and CVP. The river intakes are located near Hood in Sacramento County approximately 64 km (40 miles) from Clifton Court Forebay (CCF) in Contra Costa County. This route would cross portions of Sacramento, San Joaquin and Contra Costa counties. Figure 1 depicts the configuration of the MPTO alternative."

Apr 1, 2016

By Richard L. Unger

The Crewstation Analysis Programs (CAP) is a package of computer programs that can be used to analyze some human engineering aspects of crewstation design (such as visibility and illumination) that have particular significance in underground mining. It was developed under the U. S. Bureau of Mines (USBM) Health, Safety and Mining Technology program at the Pittsburgh Research Center, Pittsburgh, PA. This manual describes the steps necessary to collect data in the laboratory to develop luminaire profiles for the CAP illumination analysis. It also describes how the CAP Illumination Model calculates illumination. 1.1 How CAP Calculates Illumination 1.1.1 Background -CAP currently includes assessments of visibility and illumination in the surrounding work area. The advantage of using computers for these types of analyses is that many design iterations can be tested quickly and efficiently to learn the effects of changes. This reduces the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where it would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design on visibility could be tested while the machine remains in service.

Jan 1, 1994

By Joseph Daly

An investigation into inaccurate scatter of pyrotechnic detonators led to the innovation of utilising existing (every day) equipment in a manner to accurately determine the true scatter of detonators. This can then be utilised to determine the accuracy of a particular batch of detonators.

Jan 1, 2014

CONTENTS PAGE Rae, Colin C.-A Possible Origin of Oil. Discussed by S. Linker, Colin C. Rae... 2 Cottingham, Kenneth.-Subsurface Conditions on Portion of Arches Fork Anticline. Discussed by David B. Reger 6 Moyer, W. Irwin.-Time to Pay Out as a Basis for Valuation of Oil Properties. Discussed by H. J. Smith 9 Pogue, Joseph E.-Future Demands on Oil Industry of United States. Discussed by James O. Lewis 11 J. J. Walsh.-Coa-lmine Ventilation. Discussed by W. B. Daly, J. J. Walsh, R. R. Sayers, H. H. Stock, George S. Rice, James W. Paul, D. Harrington, T. D. Thomas 15 Longyear, Robert Davis.-Diamond-drill Sampling Methods. Discussed by Ira B. Joralemon, J. J. Rutledge, E. C. Harder 19 Joralemon, Ira B.-Sampling and Estimating Disseminated Copper Deposits. Discussed by J. Parke Channing, John E. Hodge, E.E. Hunner, B. B. Gottsberger, W. Y. Westervelt, W. O. Hotchkiss 20 Boericke, W. F.-Sampling and Estimating Zinc and Lead Orebodies in Mississippi Valley. Discussed by J. Parke Channing, Arthur Thacher 24 Daly, W. B. and Linforth, F. A.-Organization of Mine Sampling at Anaconda. Discussed by George A. Packard, W. B. Daly, B. B. Gottsberger 25 Norris, E. M. and Rahilly, H. J.-Mine Fires. Discussed by R. Dawson Hall, W. B. Daly, Frank Haas, D. Harrington, Robert E. Tally 26 Raymond, R. M.-Safety Practice for Hoisting Ropes. Discussed by B. F. Tillson, Graham Bright, Rudolph Kudlich, J. F. Howe, Robert Peele, H. G. Davis. 30 Howe, J. F.-Use of Wire Rope in Mining Operations. Discussed by Horace F. Lunt, J. F. Howe, B. F. Tillson 36 Tanner, W. N., and Jaccard, F. C.-Wire Rope and Safety in Hoisting at Butte Mines. Discussed by Horace F. Lunt, W. B. Daly, C. L. Colburn, William Kelly, Robert Peele, B. F. Tillson, Graham Bright, Charles E. Locke 38 Richardson, A. S.-Ventilation of Butte Mines of Anaconda Copper Mining Co. Discussed by D. Harrington, Chas. A. Mitke 42 Stuart, Charles E.-Storage-battery Locomotive as Applied to Mine Haulage. Discussed by Howard N. Eavenson, Charles E. Stuart, William Kelly, Arthur Thacher, W. H. Patton, Graham Bright 45 Woodward, C. D.-Electric Haulage Systems in Butte Mines. Discussed by William Kelly, Graham Bright, Howard N. Eavenson, C. E. Arnold, Gerard B. Rosenblatt, K. A. Pauly 47 Harrington, D.-Efficient Ventilation of Metal Mines. Discussed by R. E. Simpson 52 Otagawa, Masayuki.-Mining Methods at the Ashio Copper Mine. Discussed by Horace V. Winchell, D. W. Brunton 52 Stoek, H. H. and Clagett, Thomas H.-Coal Mining Methods. Discussed by P. D. Browning, G. L. Cox, Erskine Ramsay, Frank Haas, George S. Rice.

Jan 6, 1922

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Temple Mountain mining district is unique among the uranium-producing areas on the plateau. This relatively isolated mining district is in Emery County, Utah, on the eastern flank of the San Rafael Swell, about 35 miles southwest of the town of Green River. The district lies just within the eastern escarpment of the San Rafel Reef - a rampart of rugged and tilted sandstone cliffs that encircles the highly eroded core known as the Sinbad Country. The presence of petroleum matter found associated with the ore deposits, the occurrence of uranium in various formations, and the structural deformation caused by collapsed features have aroused a great deal of geologic interest. Mine development on Calyx Flat is distinctive, in that the ore deposits are worked through 36-inch calyx-drill holes.

Jan 1, 1957