Search Documents

By Kevan J. R. Ford, Chris A. Fleming, Robert D. Henderson

"Kinross Gold Corporation’s Maricunga mine in Chile presents an ideal opportunity to apply the SART process to a heap leach operation. Given increasing levels of cyanide complexed copper in current pregnant solutions from Maricunga heaps (over 300 ppm Cu), there is a need to reduce these levels and decrease cyanide consumption and cost. Additionally, a means of disposing of this copper is required, preferably as a saleable product. The well published SART process applied to gold-copper cyanide solutions was selected as it allows rapid precipitation of cyanide soluble copper as a relatively pure copper sulphide. The process also allows effective recovery and recycle of cyanide back to the heap leach operation.This paper reviews the SART process chemistry and presents a summary of SART bench-scale and pilot plant testwork completed by Kinross. Key design parameters and engineering aspects of the proposed plant at Maricunga are discussed. SART plant operating costs and net revenue analysis are included and illustrate the compelling economics of installing a SART process plant. INTRODUCTIONMaricunga OperationCompañia Minera Maricunga (CMM), fully owned by Kinross Gold Corporation, operates the Maricunga mine (formerly Refugio) which is located 120 km due east of the city of Copiapó at an elevation of 4,200m above sea level in the Andes mountains of northern Chile. Figure 1 shows a map of the location of the Refugio mine relative to other gold and copper mines in the region."

Jan 1, 2008

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

By R. Duinker

"This paper, an update to the 2003 paper titled "Knowledge, Technology and Profit" (Twigge-Molecey, 2003) analyzes 45 "problem projects" from the mining and metals industry over the last eleven years representing $133 billion in CAPEX. The projects have been designated as "problem projects" as they did not meet their owner’s initial expectations for project performance as defined in the paper. This paper explores some of the challenges that were present, through interviews with the knowledgeable individuals that were familiar with the projects and investigations using publically available information. The aim of the exercise was to identify the key challenges faced by the projects, and the contributing factors that led to the project failures so that the lessons can be applied to future projects.The project challenges have been categorized into four themes, technical, organizational, environmental & social and missing "homework" prior to board approval. Of noteworthy interest is that environmental permitting aspects have risen to become a significant and notable contributor to problem projects in 11 years from 2003 to 2014. It is further observed that many projects have been challenged by increasing size and complexity and with execution in more remote locations since the previous paper.It is a reality that every project will face challenges. Some projects are simply more challenging than others, and success or failure of the project is often determined by whether the project team is fully prepared to respond to the challenges. This in turn is largely dependent on whether the project "homework" was adequately completed and considered for all aspects of the project."

Jan 1, 2015

By Gilberto Yanarico Apaza

"El presente texto señala las pautas necesarias para realizar una evaluación técnica integral de la influencia del collar de bolas para las operaciones de molienda, afectando al desgaste de los revestimientos de los molinos convencionales. Para la determinación del collar de bolas es necesario realizar los análisis granulométricos con la finalidad de obtener el F80 y el P80 de las muestras obtenidas en la alimentación y producto de los molinos, definir el índice de trabajo (Wi) y consumo de energía. Asimismo, se debe considerar el porcentaje de la velocidad crítica, las dimensiones de los molinos, la densidad de los medios de molienda (bolas), el porcentaje de la carga de bolas, las características geométricas de las bolas para molienda y el diámetro real de bolas, que influye de forma inversamente proporcional en la tasa específica del consumo observada."

Jul 1, 2015

By K D. Conroy

For the past year, Lowphos Ore Ltd. has been operating two desliming hydroseparators on a fully automatic basis. Automatic operation is achieved by sensing the position of the silica-magnetite interface and automatically controlling the jet water addition to maintain a desired interface position. The system further provides automatic control of the underflow pump speed in order to assist in maintaining interface position when an <Ore change occurs. Interface position is maintained at 12 inches below the surface and is -controlled within plus or minus one inch. Metallurgical unit recovery is held above 98.5 per cent, and a 10 to 12 per cent increase in concentrate grade is normally achieved.

Jan 1, 1963

By R. H. Richards, A. E. Woodward

In Rittinger&apos;s Aufbereitungskunde of 1867 occurs (p. 195) the following table, which shows the rate of falling in water of fragments of minerals, of irregular shapes and of five different specific gravities: Diameter of particles in millimeters. 10 8 6 4 3 2 1 .5 Sp. Or. Velocity in meters per second. Auriferous silver, 16..9 .8 .7 .57 .5 .4 .29 .20 Galena,. ..7.5 .62 .55 .48 .39 54 .28 .20 .14 Pyrites,. ..5.0 .49 .43 .38 .30 .26 .22 .15 .10 Quartz,. ..2.6 -30 .27 24 .19 .17 .14 .10 .07 Coal,. ..1.3 .13 .12 .10 .08 .07 .06 .04 .03 With the purpose of extending this valuable table, to cover a larger number of minerals and sizes of each mineral, and of making it more easy of application in deciding upon a sieve-scale for any group of minerals, we have prepared the curves of velocity of fall of bodies in water shown in Plates I., XI., 111. and IV., using Rittinger&apos;s formula V= 2.44d(8 —1) where V= velocity in millimeters per second. " D = diameter of particles in meters. " 8 = specific gravity of the mineral. These curves embrace a large number of specific gravities, and for each specific gravity the relation of the diameter of the mineral particle to the velocity of its fall in water is given for all diameters and velocities used in practice. The second diagram is an enlargement of the lower left-hand corner of the first, the third bears the same relation to the second, and in like manner the fourth to the third. Plate I, therefore, covers the work of the coarsest jigging 2 inches in diameter; and under

Jan 1, 1890

By Kenneth Cotingham

Many factors joined in reducing drilling activity in Ohio in 1942. Conservation Order M-68 was important, but other things, such as operators and members of drilling crews joining the armed services and going into war plants, had an important part. The reduction in number of completions was considerable. In 1941, the total of wells drilled was 1561 but in 1942 the total was 1008. The total initial daily open flow discovered by the 701 gas wells drilled in 1941 was 492,000 M cu. ft., whereas the open flow of the 471 gas wells completed in 1942 was 314,488 M cu. ft. The total initial daily production of the 333 oil wells drilled in 1941 was 10,300 bbl., and in 1942 the 181 oil wells had a total daily initial of 7570 bbl. The average daily initial per gas well therefore was somewhat less in 1942 when compared with the preceding year, but the initial per ail well increased about 36 per cent over 1941. General Activity The total depth of the 652 oil and gas wells drilled in 1942 was 1,597,000 ft. The most active county was Perry, where 63 oil wells were drilled, most of them in Clayton township. In Morgan County. where 43 gas wells were drilled, the greatest activity was in York and Marion townships. Medina County was third in number of wells drilled, although of the total of 33 gas wells in the county, 26 were in the new Hinckley township pool. The total initial open flow of these 26 wells was 39,202 M CU. ft., and was considerably larger than from any other single area. Muskingum was an active county, particularly Washington and Wayne townships, in each of which seven gas wells were drilled, and Blue Rock and Harrison townships, in each of which five gas wells were drilled.

Jan 1, 1943

By Kenneth Cotingham

Many factors joined in reducing drilling activity in Ohio in 1942. Conservation Order M-68 was important, but other things, such as operators and members of drilling crews joining the armed services and going into war plants, had an important part. The reduction in number of completions was considerable. In 1941, the total of wells drilled was 1561 but in 1942 the total was 1008. The total initial daily open flow discovered by the 701 gas wells drilled in 1941 was 492,000 M cu. ft., whereas the open flow of the 471 gas wells completed in 1942 was 314,488 M cu. ft. The total initial daily production of the 333 oil wells drilled in 1941 was 10,300 bbl., and in 1942 the 181 oil wells had a total daily initial of 7570 bbl. The average daily initial per gas well therefore was somewhat less in 1942 when compared with the preceding year, but the initial per ail well increased about 36 per cent over 1941. General Activity The total depth of the 652 oil and gas wells drilled in 1942 was 1,597,000 ft. The most active county was Perry, where 63 oil wells were drilled, most of them in Clayton township. In Morgan County. where 43 gas wells were drilled, the greatest activity was in York and Marion townships. Medina County was third in number of wells drilled, although of the total of 33 gas wells in the county, 26 were in the new Hinckley township pool. The total initial open flow of these 26 wells was 39,202 M CU. ft., and was considerably larger than from any other single area. Muskingum was an active county, particularly Washington and Wayne townships, in each of which seven gas wells were drilled, and Blue Rock and Harrison townships, in each of which five gas wells were drilled.

Jan 1, 1943

By C. C. Harris

An analytical solution of the integro-differential equation of batch grinding is proposed as a first appoximation to the xYt surface. The size distribution equation (xY plane) is a three parameter equation previously suggested. Possible refinements are outlined. Comminution kinetics research is presently following several related courses. Some are equivalent, in that they represent different ways of viewing the same facet of the problem, though the entire endeavor cannot be described as being completely integrated. The purpose of this note is to propose and discuss a framework into which the various approaches might be fitted. This must clearly be founded upon an analysis of the xYt surface.&apos; (See also Fig. 1 of Reference 26.) The investigations referred to above comprise mainly researches into the following: (1) The kinetics of the creation of the finer sizes during relatively small grinding times. This is the Fahrenwald-Arbiter-Bhrany 2-3 approach which leads to equations equivalent to a special case of the charles4 relationship. It emerges that initial production of fines follow essentially zero order* kinetics. (2) Disappearance kinetics of the coarser fractions. This appears to be a first order relationship.5-6 (3) Prediction of the xYt surface via the selection and breakage functions utilizing computer-programmed or approximate solutions of the integro-differential equation of batch grinding.5,8-17 A recent discussion by Mika et al.5 references the relevant literature up to about 1966. In addition to these main-stream researches there is some work on the minor topic of extremely long grinding time considered as a limiting case.18-19 The field is supported by investigations into the size distribution of fragments produced by breakage processes, some of this work being most valuably statistical-mechanical in nature.20-25 Better fitting equations, however, are obtained by statistical and curve-fitting methods.26 This

Jan 1, 1969

By S. Murdock, R. L. Fleischer, H. W. Alter, J. E. Gingrich

The use of solid state track deters allows totally passive, integrating measurements of 222Rn (radon) or of 220Rn (thoron) plus radon. A track-detecting solid is placed in a holder that is closed by a selective membrane and exposed to the atmosphere of interest to produce an accurately time-averaged record over times of interest that range typically from a week to a year. By selection of the proper membranes, dosimetry can be done for radon or for the sum of radon and thoron. A different membrane is appropriate for measuring radon under humid conditions such as are found in the ground. Large numbers of measurements have been made with these systems both in the ground, where radon levels are high, and in indoor environments, where levels are orders of magnitude less. Calibrations have been carried out at both high and low concentrations of radon. New results in the air at the site of the Shirley Basin mine and mill give reproducible results with month-long integrating periods. The off-site background levels are in the range 0.7 to 1.0 pCi/l (26-37 Bq/m3). The average yearlong on-site level is 1.5 pCi/l (56 Bq/m3); at the mill it is 2.6 pCi/l (96 Bq/m3); and the level measured at the backhoe in the open pit mine is 3.9 pCi/l (144 Bq/m3). The region of significantly elevated radon levels is confined to a radius of 1.6 km of the mine and mill. All of the on-site radon concentrations are less than but comparable to the typical values found in the living areas of modern energy-efficient homes.

Jan 1, 1981

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1961

By Ward M

The current and future requirements for an underground mine information management system are being met with a flexible, value-engineered approach to mine information/communication infrastructures. El-Equip has developed and delivered to over fifty mines around the world an integrated, high capacity, radio-based leaky feeder communication system called MultiCOM. To meet the requirements of recently developed advanced information management technologies, such as production and ventilation management, the system has evolved to support simultaneous mobile and fixed information delivery services over an integrated single cable system. The following paper will review how MultiCOM is enabling information/communications technology to cost-effectively implement mine monitoring and control applications. Applications described in this paper include mobile vehicle production tracking, vehicle location, ventilation system monitoring and control with integrated ventilation system simulation. The techniques described are leading the world in terms of flexible and value-engineered applications of technology in the underground mine.

Jan 1, 1995

By Jonguk Kim

Submarine hydrothermal activity and mineralization related to island arc volcanism along the Tonga arc were explored during two research cruises in October 2009 (KODOS 09H) and February 2010 (KODOS 10H), respectively. In KODOS 09H cruise, geophysical survey, including multi-beam bathymetry, marine seismic and magnetic investigations, was performed on 10 volcanoes to find out possible structural discontinuity that can act as fluid pathway for formation of hydrothermal deposits at submarine caldera system. The result provided acoustic and seismic image maps and magnetic anomaly maps of targeted volcanoes. Then, detailed seafloor observation and sampling as well as deep tow side scan sonar survey were performed in KODOS 10H cruise on 5 volcanoes which are selected as targeted areas from the previous cruise. Among 5 targeted volcanoes, TA26 shows most extensive hydrothermal activity. Hydrothermal vents and alteration zone were observed on western caldera and summit of eastern cone of the TA26. Although only weak hydrothermal alteration was observed on eastern cone, mineralized fragments of chimney and mound were sampled from western wall of central caldera on TA25 volcano. On TA12 volcano, strong hydrothermal plume and alteration zone was detected during video tows operated between SW scoria cone and small ridge. However, only small amount of hydrothermal altered rocks were collected from TA12. Although hydrothermal activity and mineralization might be formed, supported by plume detection and result of geophysical survey, only weak alteration zones were observed on other two volcanoes (TA19 and TA22). The exploration area generally show shallow depth up to several tens of meters on summit where subsurface boiling of hydrothermal fluid might occur due to low hydraulic pressure, which can affect on styles of hydrothermal venting and mineralization process observed on Tonga submarine arc volcanoes.

Jan 1, 2010

By Emre Karakaya, Niyazi Bilim

Boreholes are used for many purposes in mining operations, petroleum engineering, and construction works. Numerous factors affect the performance of drilling equipment. Researchers continue to work on the variable drilling parameters that can be adjusted in order to reach more efficient drilling operations. Penetration rate is an essential indicator in drillability analysis and estimating. This parameter is of great importance in mining projects. There are almost no models that can estimate the penetration rate for core drilling operations. Under the abovementioned circumstances, this paper focuses on developing models that allow estimating the penetration rate based on rock material properties. During the conduct of this study, drilling experiments under 11 different pressure forces were performed on 8 different rock units, and the equations which estimated the penetration rate depending on the physico-mechanical properties of the rock samples were derived. Experiments were carried out under different pressure forces to investigate the effect of the pressure force on the derived estimation models. The obtained results allowed deriving equations that ensured estimating the penetration rate based on the physico-mechanical properties of the rocks and the applied pressure force. Using these equations, the penetration rate in core drilling operations can be estimated.

Sep 30, 2020

By Frank E. Cash

The compensation-insurance rates for quarrying in North Carolina are 11 times higher than for the State?s major industry, textiles. Some operators are willing to accept this as representing the ratio of existing hazards. This was not true of the management of the Southern Aggregates Corporation, and in 1935 it tools definite steps to correct the idea of its local officials and employees that loss of life and limb in quarries is inevitable. ACKNOWLEDGMENTS The authors acknowledge gratefully the assistance and information concerning these operations furnished by H. M. Shaw, safety director (also secretary and treasurer), Southern Aggregates Corporation, Raleigh, N. C.; by the following superintendents: J. H. Rodgers, Blair Quarry, Blair, S. C.; J. D. Lane, Greystone and Rolesville Quarries, Henderson, N. C. ; J. H. Arthur, Guilquarry, Stokesdale, N. C.; J. H. Watkins, Rockton Quarry, Wendell, N. C.; P. A. Wellenborne, Reidsville Quarry, Reidsville, N. C.; and J. L. Kirchin, Woodleaf Quarry, Woodleaf, N. C.; by the various foremen at the plants, and by Murry Id. Grier, safety engineer, North Carolina Department of Labor, Asheville, N. C.

Jan 1, 1940

By G. M. Potter, J. B. Rosenbaum, Masami Hayashi

Most Japanese copper smelters are located in areas of concentrated industrial activity and high levels of atmospheric pollution. A review of unofficial sulfur dioxide emission control data from major Japanese smelters shows capture of 91 to 99.7 percent of the sulfur in the smelter feed. The bulk of Japanese smel ting capacity was constructed in the last 10 years. Six of the major sme lters use flash furnaces, and two use reverberatory furnaces. A prototype three-furnace continuous system is in use as a parallel train with reverberatory furnaces at one smelter. Most of the sulfur dioxide is manufactured into sulfuric acid. The remainder is captured by gas scrubbers that yield gypsum and sodium salts. Ready markets exist in Japan for the acid and other su lfur byproduc ts.

Jan 1, 1967

By J. P. Gous, J. J. Sutherland

"Transalloys is a silicomanganese (SiMn) producer located in South Africa, and uses only local manganese ores to produce SiMn alloy. The plant operates five open submerged arc furnaces (SAFs) with an annual capacity of 180 000 t of saleable SiMn.Maintaining tap-holes is critical for effective furnace operation, allowing proper drainage of the furnace with minimal operator interference. Using a claygun and drill arrangement installed at each furnace, tapping occurs every four hours. Tap-holes are maintained through mickey replacement and brick repairs. Three furnaces have SiC tap-holes and two have graphite tap-holes.This paper gives a review of SAF operation, furnace and tap-hole design, daily tapping operation, and maintenance practices for repairing tap-holes.IntroductionDefining tap-hole life cycle, Steenkamp et al., (2016) highlighted four main steps: installation during furnace relines, day-to-day operations, tap-hole maintenance, and tap-hole repair. The authors argued that the design of the tap-hole area should allow for all four stages in the tap-hole life-cycle. Design principles for each stage were presented using silicomanganese (SiMn) production as a case study. Here we present a further analysis of the case study by providing practical examples of how the tap-hole life-cycle is managed at Transalloys during the design, operation, and maintenance of submerged arc furnaces (SAFs) applied in the production of SiMn.BackgroundTransalloys is the largest producer of SiMn in Africa. Its smelter complex is based outside the town of eMalahleni, in the Mpumalanga Province of South Africa. Transalloys was commissioned in the mid- 1960s as a high- and low-carbon ferrochromium plant based on the Perrin process. In 1967 the plant was converted to SiMn production because of constraints in the ferrochrome market (Basson, Curr, and Gericke, 2007; Bezemer, 1995). Today, the installed production capacity is 180 000 t of SiMn annually. Plant operations consists of five SAFs (see ratings in Table I), operating 24 hours a day, 365 days a year (including maintenance), involving 280 permanent employees, with up to 120 contract employees on site at any given time."

Jun 1, 2019

By P. H. Davenport, L. W. Nolan

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Geochemical mapping provides a direct approach to delineating areas of epigenetic mineralisation and for relating the regional distribution of this mineralisation to an overall tectonostratigraphic and structural framework, as well as to extensive areas of hydrothermal alteration. Organic lake sediment is a widely available and effective sampling medium for regional geochemical mapping in Newfoundland, that has proved to be valuable in Au, Sb and W exploration

Jul 1, 1991

By Harald Vogel, Johannes Lachenski, Friedemann Koetzel, Sebastian Schnell

In this paper, a digital subsoil approach, a work-in-progress, will be presented describing the transformation from a classical 2D to digital 3D thinking process in the design of geotechnical structures. Certain pitfalls as well as lessons learned are described, and the reader can understand that the digitalization process of the design of geotechnical structures is always a problem-focused approach by creating systems for certain processes rather than setting rules or regulations. Three project examples are presented. Two of the presented project examples feature a heterogeneous geology distribution and made it necessary for the design of the foundations to work with 3D subsoil and 3D calculation models. However, the digital 3D design process in the third project, an inner-city excavation pit, is driven by the complicated boundary conditions making it necessary to work in a parametric 3D design space. All projects have in common, that new processes had to be developed. The paper concludes with a flow chart describing the process of the elaborated digital subsoil approach.

May 1, 2022

By M. I. Copeland

The investigation of the iron-gadolinium phase diagram is part of a project undertaken by the Bureau of Mines and sponsored by the Atomic Energy Commission to investigate rare-earth alloys. Data from the investigation of the iron-gadolinium phase diagram revealed a single eutectic system with very limited terminal solubility and three intermediate phases. The eutectic point occurs at about 85 percent gadolinium, and the eutectic isotherm, which occurs at 850° C., extends from the compound Fe2Gd to 99-plus percent gadolinium. Very little solubility of the solid phases in each other was observed. The three intermediate phases, FegGd, Fe3Gd, and FeaGd, melt incongruently at peritectic isotherms at 1,320°, 1,150°, and 1,080° C., respectively. The crystalline systems of the three phases were determined as follows: FegGd, hexagonal; Fe3Gd, hexagonal or rhombohedral; and FeaGd, face-centered cubic. No lowering or raising of the alpha-gamma iron transformation at 910° C., the gamma-delta iron transformation at 1,388° C., or the gadolinium transformation at 1,262° C. was observed. The principal methods used in determining the iron-gadolinium phase diagram were melting-point determinations, thermal analyses, metallographic examination, and X-ray diffraction analyses. Melting, heat treating, and thermal analyses were conducted in a vacuum or under a helium atmosphere because of the avidity with which oxygen combines with gadolinium at elevated temperatures. A few hardness values were determined, but they had no part in the derivation of the phase diagram. No other mechanical properties were determined.

Jan 1, 1962