Search Documents

By Raúl Castro, René Gómez

In underground mining, rock fragment size is a key variable for productivity because it impacts equipment selection and mining structure design. This study characterizes granular material fragmentation during its flow to understand its characteristics and mechanisms. Tests were conducted using a laboratory setup to emulate various heights where material is drawn. The fragment-size distribution was measured before and after tests for clay, concrete fragments, and gravel. Results showed that fragmentation mainly occurs in minor sizes, with significant increases in fine material as travel distance increases.

Jan 10, 2022

By Eric Klaffenbach

Valorization of slag from metallurgical industrial processes becomes ever more important as this may help optimizing and reducing the use of natural resources such as rock and sand. In view of this objective, metallurgical processes have to be analyzed in order to modify the slag composition so that it will meet the expected requirements of potential users of these resources. This paper gives the results of a thermodynamic analysis of the flash smelting process to understand the impact of operational parameters on slag chemistry and elemental partitioning in the process. It is shown that an increase of the matte grade and temperature leads to higher deportment of Pb, Zn and As to the slag. With increasing matte grade the volatilization of these elements decreases. Furthermore, the results indicate an increasing solubility of Cu and S in slag at higher temperatures.

By Dyson N. F

Mixed cobalt-nickel sulphides precipitated from ammoniacal process liquors derived from nickel sulphide concentrates, mattes, and reduced nickeliferous laterites have been characterized.The mixed sulphides are prone to oxidation on standing and are rapidly leached under relatively mild conditions. The kinetics of the leaching reactions are controlled principally by temperature and oxygen partial pressure. Although the samples have different CO:Ni ratios and have undergone varying degrees of oxidation, there is little difference in their leaching behaviour. The results suggest that a single plant would be able to process mixed sulphides of varying composition. Any copper and zinc present in the mixed sulphides as impurities also go into solution and must be removed prior to recovery of the cobalt and nickel in metallic form.

Jan 1, 1981

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By J. E. Conley

[Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft-paper industry, especially in Lie South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far re¬moved from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4?10H20), which must be dried or dehydrated in order to most consumer requirements. The waters of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery or production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.]

Jan 1, 1936

FREQUENTLY the Survey Department is caIled upon to estimate the quantity of material in various dumps, dams piles, etc... and in the carrying out of this work various methods may be employed.The method used will vary according to the particular case in hand, and factors such as accessibility of the top of the dump, steepness of its sides, height, and the condition of the material to be estimated. A certain amount of &quot;give and take&quot; must be adopted in the treatment of small local cavities and mounds.In all cases it is desirable that the surveys made should be tied on to the lease surveys for the purpose of location, and that all levels should be reduced to the mine datum. It is also desirable to obtain levels of the original surface before deposition of the material to be estimated. If these have not been obtained beforehand, levels and transfers round the top will be the next best. If space is availabIe, flat surface is chosen as a site for the dump, etc. This is of the utmost importance in those cases where the material will have to be...

Jan 1, 1925

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

By P Mulvey, M Stuckey

"Inter-aquifer leakage due to fractures caused by coal seam gas extractions or longwall mining is an important issue for both the gas and coal industries. Currently, predicting stress induced macro-porosity associated with hydraulic fracturing, depressurisation via dewatering or collapse of overlying seams to infill a void left by longwall mining, is problematic. If fractures can be located the fracture can be sealed. Locating fractures is difficult. The non-geophysical approaches to locate fractures has been to consider the mixing of different waters, particularly that of more recent shallower groundwater with older deeper groundwater, via differences in radio-isotopes integrated with geochemical models to predict likely mixing of waters. This approach is applicable under appropriately complex settings; however, it is an expensive technique and is based on the assumption that the daughter isotopes are equally non-reactive which may not always be the case.Potentially a cheaper and faster technique is to consider integrating geochemistry (mineral weathering) and hydrogeology. The chemistry of groundwater, controlled by the weathering of primary rock?minerals and?formation of secondary minerals, can not only be differentiated between geological strata but also within strata as different stages in weathering results in differing impacts on water quality (ie different reactants).Field analysis of pH, electrolytic conductivity (EC), oxidation reduction potential (ORP) and dissolved carbon dioxide together with laboratory analysis of dissolved constituents characterise the chemistry of the water. Collection of rock samples at the time of drilling for bore installation can provide the (only) opportunity to assess the media in which the groundwater resides and migrates through. An assessment of aquifer matrix chemical makeup, via bulk sample chemical analysis, X-ray diffraction (XRD) and petrographic analysis can achieve this.The chemistry of groundwater is dependent on the water velocity. Water at deposition and post-diagenesis dissolution of minerals by hydrolysis and oxidation will result in equilibria of the dissolved phase with the solid phase. Post-depositional fractures caused by either tectonic activity or weathering alter the rate of weathering and thereby the geochemistry. Slow water flow in microfractures results in water in equilibrium with the rock minerals. Faster flow in larger fractures results in water being in disequilibria with rock minerals.Fractures can alter groundwater chemistry by two pathways: changing groundwater velocity, which changes the rate of hydrolysis or oxidation mixing water from different geological strata.Both pathways cause subtle changes in the water chemistry.It is however, the dissolved phase chemical data, which can be observed over time at individual locations and/or at a point in time along a flow path, which allows the hydrogeologist to ælook up-gradientÆ and locate the zone of leakage. Hence, influences on rock/groundwater chemistry, from anthropogenic sources to natural mixing of waters, can be assessed via appropriate interpretation of geochemistry, hydrogeochemistry and flow data.This paper will use the example of the geochemical and hydrogeological characterisation of aquifers within the Hawkesbury and Bulgo Sandstone of the Southern Coalfields to the south of Sydney in New South Wales to demonstrate this approach.CITATION:Stuckey, M and Mulvey, P, 2013. Looking for fractures - integrating geochemistry with hydrogeology to find inter-aquifer leakage above dewatered or collapsed coal seams, in Proceedings Water in Mining 2013, pp 99-108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By W. W. Adams

Lower accident rates were the outstanding feature. of the second annual sand and gravel safety competition conducted in 1930 by the United States Bureau of Mines in cooperation with the National Sand and&apos; Gravel Association. Both the frequency and, severity rates for accidents were greatly reduced as compared with those shown by the first year&apos;s contest, that for 1929. Three times as many plants were enrolled, and the number of man-hours of work represented was more than doubled. Seventy-six sand-and-gravel plants, situated in 20 States, participated in the Competition, as compared with 26 plants, located in 13 States, in the year before. The number of man-hours of employment, which indicated the amount of exposure to occupational hazards, was 4,915,592, an increase of more than 100 per cent over the previous year&apos;s total of 2,259,572 hours. The frequency of accidents declined from 74.4 per million hours for all plants enrolled in the first year&apos;s contest to 42.7 per million man-hours for all plants enrolled in 1930. The accident-severity rate was reduced from 9.7 days of disability per thousand man-hours of exposure in 1929 to 5.9 days of disability per thousand man-hours of exposure in 1930. The actual number of accidents reported for 1930 by 76 plants included four deaths and 206 injuries whereas the 26 plants that were enrolled in 1929 reported three fatalities and 165 injuries. Under the rules of the contest all "lost-time" injuries are reported--that is, all injuries that disable an employee for more than the remainder of the day on which the accident occurred. If the employee is physically able to resume his work on the day following the accident, the injury is not classed as a lost-time injury. The contest covered accidents and man-hours worked by all employees at the plant who were employed by the same company, and included work up to the point of delivery of the material directly to consumer or to independent agency of transportation--in other words, to point of relinquishment of control of the material by the producer.

Jan 1, 1931

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008

By A Fyans, B Ghahreman-Nejad

This paper discusses the method and results of an options study into selection of the optimal form for a 130 m high tailings/water retaining dam, located in a region of high seismicity in central Iran. The proposed dam is part of a planned expansion project for Sarcheshmeh Copper Mine (SCM), which after construction will provide 550 million tonnes of additional tailings storage over the next 27 years. Geotechnical investigation at the proposed site indicated that adequate suitable low permeability materials (i.e. clay) were not available in the immediate vicinity of the dam site and would need to be imported from a distance of well over 10 km (direct). Given the magnitude of the estimated quantity of material and construction cost it was considered prudent to compare the cost of alternative dam design options for the proposed storage. A total of five dam design options are considered including a conventional rockfill embankment dam with an upstream sloping earth core (ECRD), a geomembrane face rockfill embankment dam (GFRD), a sloping asphalt core rockfill embankment dam (ACRD), a roller compacted concrete dam (RCCD), and a filter rockfill embankment dam for tailings storage together with a separate smaller earthfill core rockfill dam (ECRD) located downstream for storage of decant water. The risks, costing and design of all options are discussed in detail and the outcome of the study is presented.CITATION:Ghahreman-Nejad, B and Fyans, A, 2018. Optimum embankment design for a tailings dam, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By Tony P. Suckling

This paper describes an investigation into the bleeding behaviour of bentonite slurry observed on a trial diaphragm wall panel. The bleeding is thought to be due to the bentonite experiencing a chemical reaction leading to settlement of the solids within the fluid, possibly as a self-weight consolidation process. The trial panel was constructed in a busy airport environment where many different chemical products are used for de-icing the aeroplanes, runways, apron areas, vehicle access and pedestrian routes. The relationships between slurry contamination, bleeding, bentonite hydration time and filter loss behaviour were examined as no relevant published literature could be found. The results show that the amount of bleed strongly depends on both the degree of contamination and the hydration time. It is concluded that bentonite fluids should be allowed to sit in the storage tank for at least 24 hours after mixing, and that the filter loss test is a quick and effective method to determine the potential for bleeding of contaminated slurries.

Jan 1, 2011

By Edward F. Fries

The U.S. Bureau of Mines is conducting research that will lead to computer-assisted mining equipment. This research will facilitate improvements in safety by relocating workers from dangerous areas and will increase production by providing more accurate control with less downtime of equipment. A Bureau-developed microcomputer network enhances this research by permitting a group of diverse computers to interact with a mining machine as well as with each other over a common data link. The network is composed of specially integrated off-the-shelf hardware and industry-standard operating system and programming languages. Using the network, researchers can conduct various experiments with the mining machine using a diverse group of sensors, computers, and micro controllers. This report gives a brief background on the Bureau&apos;s work in computer-assisted mining, followed by discussions on the network hardware and architecture and the network packets, and an analysis of network operation.

Jan 1, 1992

By R. A. Vik

The influence of thermal treatments on the grindability of low-grade hematitic iron ores from Michigan and Minnesota was examined in bench-scale tests. Treatment factors were roasting temperature, roasting atmosphere, and ore cooling conditions. Bond ball mill grindability and work indices were used as response indicators in evaluating the condition of the ore. Of the three treatment factors evaluated, roasting atmosphere, which brought about the con version of iron oxides to magnetite, had the most significant effect; roasting temperature had the next most important effect; and cooling condition had the least effect. Optimum grindability was obtained with reduced-quenched products of both ores at 650° C, near the alpha-beta phase transformation of quartz.

Jan 1, 1971

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

Generating short- and long-term mine production schedules in isolation and independently from each other means that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and long-term activities simultaneously. This paper addresses the task of integrating short- and long-term production plans by combining the short-term objective of minimising deviation to targeted mill feed grade with the long-term objective of maximising net present value (NPV) into a single mathematical model. A case study is presented which compares the present values of the same stope data set scheduled via separate long and short-term models and than by the proposed integrated model which applies a predetermined penalty for each tonne of metal deviation to target for the respective ore tonnage being processed. This allows an operation to obtain a globally optimal scheduling regime when taking into consideration the cost and loss of value resulting from fluctuations in grade to the mill over the short-term.

Dec 6, 2010

By Richard A. Rivell

This document is a users manual intended as a reference for personnel interested in the analysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The interactive procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures available include Gauss-Seidel and Newton-Raphson iterative techniques for the analysis of normal operation or balanced faults as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults.

Jan 1, 1980