Search Documents

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Boden A

A procedure was developed for recovering metal values from copper-smelter fume. The fume is first leached to neutrality with dilute sulphuric acid to obtain a solution of zinc sulphate containing a low level of impurities. The tailings from this leach are treated with hydrochloric acid in two stages, in which tin and zinc are quantitatively leached and recovered as a tin concentrate and a zinc sulphatelzinc chloride solution.About 80 per cent of the lead sulphate is converted into lead chloride, which can be recovered as a pure product.Data on the effect of temperature, acid concentration, aeration, and solid/liquid ratios on the hydrochloric acid leach are presented, and the fate of the most important metals during the recovery process is described. Alternative treatments of the tailings from the neutral sulphuric acid leach were briefly investigated.

Jan 1, 1977

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By Madgwick J. C

Microaerobic biodegradation oflow-grade manganese dioxide slurry tailings was demonstrated in enrichment cultures treated with dilute molasses at 30°C and pH 5·8. Supplementary nitrogenous nutrients, yeast extract addition and pH adjustment were not required.Continuously stirred, air-limited reactors were superior to still intermittently agitated cultures, in that, at 5 per cent (w/v) MnOz tailings and 5 per cent (w/v) molasses, the yield of 0.12 g Mn++/g molasses, the rate ofleaching of 1·06 g Mn++/l/d and a recovery of Mn++ of 58 percent from MnOz were 2·8 times, 1·7 times and 1·9 times greater, respectively. The best compromise in yield (0·45 g Mn++/g molasses) and rate ofdissolution (0·73 gMn++/l/d) was at 1 per cent (w/v) molasses in a stirred reactor.Where leaching organisms were separated from sterile ore by a bacteria impermeable membrane leaching was shown to be some 20 per cent due to diffusible metabolites and 80 per cent due to a direct contact between the bacteria and the ore particle's surfaces.

Jan 1, 1986

By J. S. Coffman

Wyoming is estimated to have more than 700 million tons and Utah more than 2.5 billion tons of +10 percent P2O6 phosphate rock considered to have some future economic potential. In Wyoming, the +24 and +18 percent P205 rock potential resources total nearly 250 and 450 million tons, respectively. In Utah, the +31, +24, and +18 percent rock total approximately 33 million, 222 million, and 2.2 billion tons, respectively. These resources are all located above the local drainage levels and do not include latent resources. All of the mining and beneficiation of phosphate rock in the two States is done by San Francisco Chemical Co. The facilities include open pit mines at Vernal, Utah, and Leefe, Wyo.; an underground mine in the Crawford Mountains, Utah, and beneficiation plants at Leefe and Vernal. One of the principal markets for the phosphate rock is Western Phosphates, Inc., fertilizer plant at Garfield, Utah. Recent exploration and development has been under-taken by different companies in the Southeastern Wind River Range, Sublette Range, and Crawford Mountains. The facilities at Leefe and Vernal are in the process of expansion. Some of the areas of western Wyoming contain vast quantities of phosphate rock in minable units, but, because of their remote location, are classed as latent areas. In these areas, there are estimated to be about 700 million, 2 billion, and 3 billion tons of phosphate rock in the +24, +18, and +10 percent P205 grade classes, respectively. The Snake River Range of Idaho and Wyoming is also estimated to contain roughly 21, 106, 177, and 214 million tons of potential resources in the +31, +24, +18, and +10 grade categories, respectively. This area also contains a large amount of latent rock in the more remote areas.

Jan 1, 1967

All development proposals have to run the gauntlet of the approvals process. Major resource projects are generally subject to particularly intense scrutiny. The key element in the approvals process is that it is about making decisions that take into account the benefits or otherwise to society as a whole - the interests of any one group do not take precedence. Most groups tend to see their relatively narrow interests as representing those of the broader society. Each group develops their arguments for or against a project in isolation, and then presents these to an arbiter in an adversarial situation. From this mire of argument and counter-argument it is often difficult to discern just what the real benefits of a project are, and opportunities for agreement and constructive modification of proposals to meet real concerns are often missed. The contention made in this paper is that the inevitable differences between these various viewpoints should be harnessed to help the proponent to come up with a proposal that is clearly of overall benefit to society and which gains approval. It is better to accept that no one group has a monopoly on wisdom in this area and to engender an environment of creative tension in which the pros and cons can be broadly considered and good planning and design used to produce a proposal that has a high chance of success. There are a variety of ways in which this approach can be implemented. Some of these options will be discussed in terms of their likely applicability to energy projects and their potential for success.

Jan 1, 1992

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012

By T. M. Barczak

The term "resultant load vector" is defined as the representation of the forces applied to a longwall roof support element by strata activity through a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield structure prohibits determination of support resistance simply from the summation of leg forces. In the research reported in this Bureau of Mines study, the mechanics of the shield structure were evaluated, and a technique was developed whereby the resultant shield loading could be determined by instrumenting supports with pressure transducers and strain gauges to measure leg, canopy capsule, and lemniscate link forces. This technique has been laboratory tested in the Bureau's Mine Roof Simulator. Functional relationships among variables were assessed, and confidence intervals were established for prediction of the resultant load vector parameters. Resultant load measurements were taken on five instrumented shields on an active longwall face in Colorado. Results were analyzed and found to be consistent with shield mechanics and anticipated roof behavior. Benefits to be derived from this research, future efforts, and long-range goals are discussed.

Jan 1, 1986

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

When underground extractions occur beneath or in close proximity to valleys and other forms of irregular surface topographic features, the observed vertical subsidence at the base of the valley is less than that would be expected in flat terrain, while the valley sides are observed to move inwards towards the centre of the valley. The reduction in subsidence at the bottom of the valley is referred to as upsidence and the convergence of two sides of the valley is termed valley closure. Research coupled with mining experience over the past few decades in Australia has identified valley closure subsidence as being very real and quite significant part of non-conventional subsidence effects, which always have adverse effects on natural features, with risks to water flow and aquatic ecosystems. In this paper, we describe a threedimensional numerical modelling approach to investigate the geomechanical mechanisms which cause the valley closure subsidence behaviour, using distinct element computer package 3DEC. The calibrated models can accurately predict subsidence and horizontal displacements, and they are subsequently extended to specifically study the effect of a series of mining geological and topographical factors on valley closure subsidence phenomenon, by developing a range of hypothetical scenarios. Previous analyses carried out using a two-dimensional numerical modelling technique have identified the potential parameters that affect the valley closure subsidence, which mainly include longwall position, horizontal stresses, valley sloping angle, and valley shape. Further three-dimensional analyses regarding the relationships between the major factors and valley closure subsidence are discussed in this paper. The results have significant implications with regard to both the underlying mechanisms that lead to this nonconventional subsidence behaviour, and how these should be incorporated in future valley closure subsidence prediction and mitigation of its impacts on natural features.

Jan 1, 2015

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By J. P. Walker

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk-type nagger sponge iron, has an excellent reputation as a superior furnace feed wherever high-grade steels are made.The general procedure for making brickyard sponge iron was described frequent in Swedish technical journals before 1932 and at that time consisted in filling clay refractory containers, called saggers, with iron ore plus the necessary quantity of solid reducing agent and then firing in an ordinary ceramic kiln. Two types of sponge iron were made in this way: (1) An inferior, high-sulfur product obtained by mixing the ore and solid reducing agent; and (2) a high-grade, low-sulfur product made by filling the sagger with alternete layers of unmixed ore and reducer, yielding sintered disks of metallic iron particles.Swedish disk-type sponge iron of interest to the steel industry because it has a very low sulfur content, even when made by the use of low-grade, high-sulfur coals for reducing and firing. The Swedish product also contains little siliceous gangue residue and is almost phos¬phorus-free. To those features must be added the high metallic-iron content -90 to 96 percent - and freedom from even small amounts of the metals that are undesirable in steel making.The details essential for successful operation of this procedure are not known, especially as regards improvements said to have been made since 19;2. The Bureau of Mines therefore decided to determine some of these missing details, and this report records the results of the first set of experiments on the manufacture of brickyard or sagger sponge iron."

Sep 1, 1945

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By H Kurth, L Balzan

On-belt analysers have been used since the early 1980s in the coal sector to measure ash content in real time for diverting material on conveyors to remove waste, bypass beneficiation and allow suitable material to proceed to the wash plant for processing. Since 2008, a GEOSCAN-M elemental analyser has been used on an overland conveyor in South Africa to divert direct-shipping quality iron ore to bypass a jig plant. This paper focusses on recent evaluation work to determine the suitability of an on-belt analyser to upgrade the processing plant feed in a copper-gold operation.Copper-gold ore samples from New Gold’s New Afton Mine near Kamloops, BC, Canada were tested to assess measurement accuracy over short time increments. A two-minute measurement increment has been used in the minerals sector as a compromise between good measurement accuracy and a useful tonnage (haul truck equivalent size or smaller). At New Afton, this increment represents approximately 35 t of material. Segregation decisions are currently made after visual and sometimes analytical determination, at increments of approximately 500 t to designate material as ore or waste at the drawbell in the cave.Results of test work including the composition range and expected accuracies by element are shown. The operation, which is not mine constrained, was evaluating the potential for ore upgrading through waste and low grade increment diversion to upgrade ore quality feeding the mill. Prompt-gamma neutron activation analysis (PGNAA) was considered as the company recognised that it would measure through the full conveyed cross section continuously and produce multi-elemental measurements unaffected by particle size, dust, moisture content, layering and segregation, mineralogy and belt speed.GEOSCAN analyses over various analysis periods will be collected to identify variability in the conveyed material quality and used to generate tonnage-grade curves so that an optimal diversion (bulk sorting) tonnage increment can be determined. Measurement increment time can be customised to suit site requirements. CITATION:Kurth, H and Balzan, L, 2017. Assessing bulk sorting suitability at the New Afton mine, in Proceedings MetPlant 2017, pp 315–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By A. G. Rozner

TRANSVERSE rupture tests have been commonly used in mechanical investigations of brittle materials. The specimens are simple, easy to prepare, and loading presents no difficulty. Owing to the complexity of stress distribution in bending1 one can determine stresses rigorously only for the elastic range. The bend-test results, however, are at times converted into tensile-strength data, determined as maximum fiber stress. The assumption is made that for small plastic deformations the linear stress-strain relation applies. This problem was experimentally investigated by Bach3 who tested cast iron in bending and in tension and found that the maximum fiber strength obtained in bending exceeded the experimental tensile strength by a factor depending on the geometry of the tested piece. The factor varied from 1.57 for a rectangular cross section to 2.12 for a circular cross section of the tested beam. Since this work was carried out 60 years ago, the cast iron used could be expected to have been highly brittle, thus the extent of plastic deformation prior to fracture very small. We have therefore carried out a number of tests on magnesium-modified cast iron with an average elongation of -5 pct. It was hoped that the data obtained from the tests would serve as a guideline for comparing data obtained in tension and bending for brittle materials. Mechanical properties were measured at room temperature on an Instron tensile machine at a crosshead speed of 0.05 in. per min. The three-point bend test employed cylindrical bars 0.20 in. in diameter with a 1.0-in. span. For the tensile test, cylindrical tensile specimens with a gage length of 0.85 in. and a diameter of 0.160 in. were used. Results are summarized in Table I. From Table I one can see that fracture strength

Jan 1, 1965

By Ernest R. Lilley

THOSE acquainted with the fundamental differences between the, educational .systems of Great Britain and. the United States would hardly expect .the training of men for the petroleum industry to proceed along the same lines- in the two countries. The youth entering an English university is, except in the case of-the student from some of the British colonies or from foreign countries, almost invariably a product of the English "public school." This is in no sense comparable .with the American public school. It is a private institution, frequently of considerable age and heavily endowed. In many aspects it seems to be comparable with the American preparatory school. Yet to some extent its activities remind one of the first years of the undergraduate: course in the American college. Certainly it takes to-itself many of the social, functions of the American college.

Jan 1, 1931