Search Documents

1. Healthy and active Local Section organizations are vital factors in promoting the vigor and growth of the Institute. 2. Activity on the part of Local Sections should be recognized and stim¬ulated by appropriation of funds from the Institute's treasury; and these appropriations should be as large as is consistent with the relative needs for other activities. 3. As between different Sections, the amount of such appropriations should be based primarily on the extent of activities as reflected in the number and character of meetings .held and the attendance of the members at such meetings. 4. In making a request for funds for any year, the officers of a Local. Section should submit: (a) a report showing in reasonable detail its income, and expenditures for the preceding calendar year; (b) a statement of the number of. members to whom announcements of each meeting had .been mailed; (c) a record of meetings held, the character of the program, and _ attendance of members at each; and (d) any further facts having a bear¬ing on its financial requirements for the coming year.

Jan 1, 1937

By W. J. Millard

Owing to a moratorium in the drilling of crown-land leases in Trinidad during the year of 1931, only 40 wells were spudded in during the first eight months as compared with 110 during the same period in 1930. Nevertheless the production will show an increase of about 400,000 bbl. over that of 1930. An estimate is given in Table 1. Since the oil produced in 1930 was 9,418,907 bbl. and that in 1931 probably will be 9,853,976 bbl., the year 1931 probably will see an increase of about 4.6 per cent. The gross production of crude oil in the colony has increased steadily year by year, with the exception of 1919, when there was a slight decline. A tabulated statement was given last year.' The Petroleum Times of March 21, 1931 (p. 413) gives the total production of 1930 as 9,418,000 bbl. and the average monthly production as 784,833 bbl. The same two items for 1931 are estimated at 9,853,976 and 821,165 bbl., respectively.

Jan 1, 1932

By J. W. Halley

COPPER has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is diffi-cult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile" steels. They were designed for use in the "hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels."

Jan 1, 1940

By W. H. Tuttle, H. R. Ahlquist, A. J. Carlson

Variations of the EVOP technique are accepted as the foun- dation in the development of Erie Mining Company's mining, concentrating and pelletizing complex at Hoyt Lakes, Minnesota. The basic one-variable- at-a-time technique served its purpose through the laboratory pilot plant as well as the full-scale production sized pilot plant. However, recognition by Erie Mining Company management of the potential of computer application and statistical experimentation in plant operation and testing led to acquisition of an IBM 1620 computer in 1961. Adaptation of established techniques in statistically designed experimentation and analysis of results is presented in actual case form including the following: 1. Determination and use of variance, standard deviation, standard errors; application of t-test in determining true differences between daily aver ages of product assays; formulation of quality control limits; determining sample size; and application of normality tests will be discussed. 2. Use of mathematical modeling and regression analysis for establishing mill storage conditions based on bin level indicator lights. 3. Polyvariable random balance design of a balling circuit test and resultant identification of primary control variables.

Jan 1, 1969

By Donald W. Gentry, John F. Abel

This paper presents some of the results of a rock mechanics instrumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam, and immediately below the coal seam. Longwall test panel 4N had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft), Fig. 1. The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) although it ranges from 73-134 m (240-440 ft). Roof support at the face was provided by 116 Hemscheidt 320 HSL shields. These shield-type supports weigh 11.4 metric tons each.

Jan 3, 1978

By Francis A Thomson

Montana Bureau of Mines and Geology, Montana School of Mines, Butte, Mont Francis A Thomson, President. The Bureau of Mines and Geology was formerly known as the Bureau of Mines and Metallurgy. A list of publications will be sent upon request¬ A series of six Bulletins and five Memoirs liave been issued by tlie Bureau, as well as several miscellaneous contributions Where the price is not indicated in tlie following selected list of those publications which are now available, the publications are presumably distributed gratis: Bulletin 3, Mechanical ore sampling in Montana, by H B Pulsifer (1920); 6, Geology and ore deposits of Bannack and Argenta, Montana, by P. J Slienon, 50 cents, Memoir 1, The Kevin-Sunburst and otlier oil and gas fields of the Sweetgrass Arcli, by E S Perry (1929), 2, Natural gas in Montana, by E S Perry (in preparation), 4, Tlie geologic structures of western Montana, by C H Clapp and others (in preparation), 5, Placer mining possibilities in Montana, by O A Dingman (1932).

Jan 1, 1933

By Clarence F. Zeuch

Mr. Shaw's work showed the dodecyl mercaptan as a very good collector compared with other collectors on Cu-Mo ores, Mo ores, and for Au and Au-Ag ores plus Pt ores. However, as one who has had extensive experience on Cu-Mo ores, the work is not complete in making only a rougher concentrate with a collector; the work must be carried on in making a Cu-Mo separation. Did Mr. Shaw do any of this work? Before trying the dodecyl mercaptan as a Cu-Mo collector for the Cu-Mo ore it would be well to have any new work conducted knowing how the reagent acts on the Mo. Will it allow a good separation? The use of the collector at Palabora was also mentioned. From some earlier literature I thought that the reagent has been used as an oxide Cu collector after the sulfide mineral was floated out. I thought the pH at this point was about 1.5-3.0. I would like to have this point clarified.

Jan 1, 1982

By C. H. Wilson, J. J. Jakosky

In recent years geophysical prospecting methods have become well established as important steps in economically initiating new mining ventures in the field of base-metal exploration, placer mining and water-supply problems. The value of these methods as applied to these problems has been greatly increased by new and improved instruments, and a greater degree of skill in laboratory and interpretative technique. Considerable success has been attained, with subsequent drilling checking the predicted depths within 1 to 5 per cent, on problems requiring information on thickness of fill material, depth to and contour of bedrock, extent and yardage of gravels to be mined, and location of hydrostatic water table. In these applications the geophysical work gives data comparable to drilling, and at a cost of about one-fiftieth that of drilling. Discussion of several surveys with accompanying illustrations showing geophysical methods applicable to both simple and complicated placer problems are contained in the paper. The electrical instruments for measuring electromagnetic field strength and surface potentials are described, and their use, coupled with that of other geophysical instruments in modern field procedure, is noted.:

Jan 1, 1934

By H. I. Aaronson

THE TTT-curve for the beginning of transformation in hypoeutectoid steels containing appreciable amounts of relatively strong carbide-forming alloying elements often exhibits a "bay" at intermediate temperatures. In many of these steels, proeutectoid ferrite is the initial product of the decomposition of austenite not only at temperatures above the bay but also in an appreciable temperature range below the region of the bay. Hultgren has postulated that ferrite formed above the bay, termed "orthoferrite", contains the equilibrium concentration of alloying element at temperatures above the eutectoid range, and the extrapolated metastable equilibrium concentration at lower temperatures. The ferrite formed below the bay, on the other hand, termed "paraferrite", was assumed to inherit completely the bulk alloy content of the austenite without regard for the compositional requirements of equilibrium. As shown schematically in Fig. 1, the two types of ferrite were taken to have different Ae3 temperatures and different C-curves on a TTT-diagram. Their different kinetic behaviors were thus considered responsible for the bay in the TTT-curve for the proeutectoid ferrite reaction in this type of alloy steel.

Jan 1, 1962

The thirty-ninth meeting of the Boston Section was held at the Engi- neers? Club on Monday evening, Dec. 4, 1916. Thirty-three members and guests sat down to dinner; There were present as section guests; Dr. L. D. Ricketts, and Prof. Bradley Stoughton, President and Secretary of the parent society, and each was called upon to speak. Mr. Stoughton spoke of the growth of the Institute during the past year and described the very numerous and important activities, of which the junction of the American Society of Civil Engineers with the other three societies is perhaps the most important. Dr. Ricketts, the advertised speaker of the evening, spoke on Recent Progress in Mining and Metallurgy of Copper Ores. In discussing the improvements in mining, he traced the mining methods from square- set mining to the modified Ohio System now so successfully used at Inspiration: In metallurgy, he described the growth of reverberatory-smelting ant1 allied problems such as the utilization of the waste heat for generating steam. He laid stress on the importance of sampling and bedding of

Jan 6, 1917

By Paul T. Allsman

Passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of the Federal Government into the problems of mining. Such a law was necessary simply to help re- solve a number of disputes in mining. Now, however, a hundred years later, the extent of government involvement in the mineral industry often comes as a shock to the mining engineer who has reached management level. In fact, he has been poorly prepared for an understanding of the role of government in the industry and he becomes frustrated, even hostile. In our political system, private industry is responsible for producing minerals and the Government sees to it that production will be adequate for a peace-time economy and for any emergency. There have been great social and political changes since World War I1 with the result that the Government's participation in our society has steadily increased. A new dimension in business and government relations has been introduced which should be examined more closely.

Jan 5, 1966

By J. M. Lohr

A COMMERCIAL development requiring a suitable alloy or alloys for sealing into various grades of glass made it desirable to have a more exact knowledge of the expansion characteristics of the nickel-iron alloys than appeared in the published literature. The expansion of the more common. FIG. I.-EXPANSION CURVES OF SEVERAL FIG. 2.-EXPANSION CURVES OF TWO TYPES OF GLASS. (Courtesy of R. C. A.) TYPES OF GLASS. (Courtesy of R. C. A.) types of glass under consideration varies from 2.7 to 10.4 X 10-6 per degree Centigrade, over the range 20° to 400° C. For reference, the thermal expansion curves f several types of glass used for sealing by the lamp and tube industries are given (Figs. 1 and 2). This paper covers a detailed investigation of the thermal expansion of a series of nickel-iron alloys in which the nickel content varies from 30 to 70 per cent. Particular stress is laid on the alloys that contain between 40 and 55 per cent Ni.

Jan 1, 1938

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969

By O. E. Palasvirta

Close examination of most so-called n.eu processes in mineral dressing reveals that they were conceived and developed a long time ago. High-intensity magnetic separation is no exception. Although its application in iron ore beneficiation seems new, in Germany the process has been commercially successful for almost two decades. High-intensity separators have long been standard equipment in the glass sand industry; they have also been used in concentrating some of the more unusual para-magnetic minerals. The basic features of an induced-rotor, high-intensity magnetic separator were described by Desire Korda in Paris in 1905,' and many patents have since been issued for improvements on the original design. Fig. 1 shows the basic design of an induced-rotor separator. Several U. S. manufacturers have been supplying induced-rotor separators for many years, but these are all devices of relatively low capacity, not suitable for treating such low-cost commodities as iron ore. On the other hand, two German manufacturers are offering induced-rotor separators of high capacity, both proven in the field. The present investigation was prompted by the apparent success of the German installations and by the discovery of iron ores on this continent which may be amenable to high-intensity separation. The objective was to gain better insight into the underlying principles of separation in a high-intensity field and to use this knowledge in selecting or designing an optimum separator. THEORETICAL CONSIDERATIONS he well known low-intensity magnetic separators are. without exception, of the the magnet type with more or less similar field shapes. It is therefore permissible to speak of their comparative strengths in terms of field intensity alone. However, proper understanding of the high-intensity magnetic separation process requires somewhat deeper analysis of the relationship between the magnetic field and the attractive force. Contrary to a widely held belief, a magnetic field of parallel lines of flux exerts no attractive force on a magnetically susceptible particle, but merely aligns its poles parallel to the lines of flux. On the other hand, a non-uniform field attracts a magnetically susceptible particle in the direction of the converging lines of flux. Thus the force of magnetic attraction varies as the product of the field intensity and the field gradient: dH ds As the induced-rotor magnetic separator is primarily intended for separating feebly magnetic materials, it is important that maximum attraction be attained. For the designer, then, the relationship between the magnetic field and the attractive force has the following implications: 1) Insofar as possible, the separation gap must be saturated with flux. 2) The rotor surface must be shaped to insure maximum convergence of lines of flux toward the rotor. 3) The primary pole face (opposite the rotor, on the other side of the separation gap) must be shaped so that the lines of flux do not diverge from it at any location in the effective separation zone. The actual attractive force of the rotor, and its critical speed, can be calculated as shown by Runo-linna, provided that the true flux density, the field gradient, and the magnetic susceptibility of the mineral can be measured with sufficient accuracy. The irregular shape of the rotor surface makes flux measurements difficult, but it can be done if a suitable gaussmeter is available (see Fig. 2). Calculations by the author, and comparisons with the centrifugal force exerted by the rotor, indicate that the force pinning a hematite particle to the rotor is of the same order of magnitude as the force holding a

Jan 1, 1960

By C. E. Violet, R. J. Borg, E. M. Howard

The miscibility gap in the Au-Ni system has been determined by Mossbauer spectroscopy, with used as a probe. The phase boundaries were determined from the compositional dependence of both the isomer shift and Curie temperature. X-ray diffraction measurements were also used to confirm the Mossbauer results. 1 HE purpose of this research is to demonstrate the application of Mbssbauer spectroscopy to the determination of phase boundaries and to redetermine the miscibility gap by an independent and novel technique. The techniques evolved in this study are readily applicable to other polyphase systems and are generally as quick and accurate as the more conventional methods, e.g., metallography, X-ray diffraction, thermal analysis, and so forth. To be sure, not all polyphase systems will lend themselves favorably to Mijssbauer investigations, but this is a problem met in the use of conventional methods as well. The Mbssbauer spectrum responds to a different set of physical parameters, and consequently provides an entirely independent method of analysis. It is especially useful if the system has either a ferromagnetic or an antiferromagnetic transition. The Au-Ni system was selected because alloys containing more than -60 at. pct Ni become magnetically ordered at low temperatures; also the miscibility gap is quite well established (see Ref. 7 for a compilation of pertinent references, also Fig. 11, and thus provides a reliable test of this novel procedure. As Fe is the most commonly used Mijssbauer isotope, there exists a wealth of information concerning its behavior in iron-containing alloys and compounds. However, as yet there have been relatively few experiments using it as a probe to investigate nonferrous systems. By choosing a nonferrous alloy system, we are able to demonstrate that its use is not restricted to systems containing iron as one of the major constituents. Wertheim and ~ernick' have used the same method to investigate Cu-Ni, and demonstrated that one can obtain a systematic variation in the isomer shift and magnetic hyperfine field. However, we believe this to be the first time these techniques have been used to establish phase boundaries. Two hyperfine interactions were measured and used to determine the phase boundaries, viz., the magnetic hyperfine splitting and the isomer shift which in this alloy system are both strong functions of composition. Calibration curves were established based upon single-phase solid solutions obtained by quenching from temperatures well above the maximum of the miscibility gap, see Fig. 1. Solid solutions containing 25, 50, 65, 75, 85, 92, and 96 pct Ni as well as pure nickel were used in the calibration procedure. Fig. 2 shows the Curie temperature, TC, and the isomer shift, v,, as determined from the Mbssbauer spectra, and variation in lattice parameter as determined by X-ray diffraction, as functions of composition. The compositions of the two-phase systems quenched from temperatures within the miscibility gap are obtained by comparing their respective values of TC and v0 with the calibration data. I) EXPERIMENTAL Mbssbauer sources were made by fusing the component metals in a tungsten arc melter, which has a water-cooled copper hearth. Both nickel and gold were 99.999 pct pure, and the melting was done in an atmosphere of purified argon. The alloys were rolled, diced,

Jan 1, 1969

By Leon Merker

FLAME fusion growth of strontium titanate crystals was undertaken to obtain large transparent crystals on which physical data could be gathered. The fact that strontium titanate is a cubic crystal and probably has a high index of refraction indicated that it might be useful in optics. No large boules* of strontium titanate had been synthesized previously, and none have been found as natural occurrences. The flame fusion process, invented by Verneuil in 1904,1 was first applied to grow large crystals of ruby and has since been used extensively to grow crystals of corundum and spinel on a commercial scale. Only during the past nine years has this technique been applied to the growth of large single crystals of other high melting compounds such as rutile,2 mullite,3 and ferrites4 One of several significant advantages of the flame fusion technique over more conventional methods of growing crystals from a melt is that the crystals are grown without the use of melt containers. This fact alone excludes other methods of growing crystals from a melt whenever there are compounds with a melting point near 2000°C or above. Growth of the crystal, similar to that of a stalagmite, takes place inside a circular refractory furnace that does not contact the crystal, Fig. 1. This eliminates a serious source of impurities as well as the likelihood of multi-crystalline solidification along the container walls. The flame fusion technique is particularly advantageous for research because it produces large crystals quickly and at lower cost. A corundum crystal 25 mm long and 12 mm in diam can be grown in 2 to 3 hr. Operating conditions permit observation of the growing crystal during any stage of the process. The various flame patterns and a wide range of oxidation-reduction conditions can be investigated in a relatively short time. It should be pointed out that formation of the foot of the boule is the most critical step in growing an unfractured boule. When the tip of the sintered cone is fused to initiate crystal growth, the original area of fusion should be kept as small as possible so that one crystallite can assume dominance over all the others and propagate as a single crystal. If the boule start happens to consist of several crystals, usually the entire boule also contains several crystals. In many cases these tightly cohering crystals exhibit different crystallographic orientations. Although the basic technique of the original Verneuil process has been retained, refinements in method and burner design have been developed in recent years. For example, boule growth may be initiated on a seed crystal rather than by fusion of a sintered cone. The danger of multicrystalline or twinned boule starts is thus eliminated, and this procedure may also be used to grow boules of predetermined crystallographic orientation. Prior Art: Of the many attempts to produce artificial gem crystals, most early efforts% ere directed toward synthesis of .rubies and sapphires and diamonds. None of these efforts resulted in a process that was commercially practical. Without exception only tiny crystals of corundum were obtained, and those at excessive cost. Verneuil announced his process in 1904; Ravier6 in 1934 presented a detailed description of a commercial boule production plant. Descriptions of the German synthetic stone industry, the process details, and the equipment used have been published by Barnes7 and by Merker.'

Jan 1, 1956

By H. R. Stahi

THE ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classifiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9 1/2 -in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3 ½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 5 2 ¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1 3/4in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges are renovated occasionally, broken pieces being removed and the charge brought up

Jan 1, 1945

By A. E. Bellis, T. W. Hardy

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operatioqs. Hundreds of dollars are spent in the design and manufacture of milling cutters of special form for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring-the tool out "clean," is a difficult one and calls for no small amount of skill. In order to be on the safe side the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed stee1, in which metallographic means were used to determine the correct hardening tempcratures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accom- . panying table. Six specimens from the same bar of each kind of steel

Jan 1, 1917

By I. W. Alcorn

THE cost of drilling in the past few years of proration and ever decreasing allowables has received increasing thought and study. It seems to parallel the strides made with respect to pumping problems in 1932 and 1933. Low profit margins stimulate the search for economies. Any discussion of slim-hole drilling involves a multitude of abstract values, and the problem can be attacked only by a study of records and rational thinking. In a measure, traditional methods must be studied with a questioning attitude. The words "slim hole" may be somewhat misleading, as the term is entirely relative. For that reason I wish to define it as used in this discussion. On the Gulf Coast, I would define a normal hole as one in which 10 3/4-in. surface casing has been set and below which a 9 7/8-in. hole is dug. With this as a datum, holes of larger diameter below surface would be called "large holes," with 12 1/4 in. as the "extra large" class and holes of smaller diameter classed in the slim-hole range, 6 1/4 in. representing about the minimum size. The optimum size has not been definitely determined, but the preference is for a program that would call for setting 8 5/8-in. surface casing and digging a 7 3/4-in. hole. Different sections of the country might very properly deviate from this practice because of differences in depth, formations, regulations, or other factors. This paper will be confined to a discussion of the drilling of exploratory wells, as the drilling of this class of wells is quite a different problem from that of drilling a proven field, although many of the same considerations apply in both cases, as will be apparent. Although for many years shallow slim-hole and core-test holes of small diameter had been dug, it was not, I believe, until the fall of 1937 that serious consideration was given to its application in drilling wells 7000 ft., 8000 ft. and 9000 ft. deep on the Gulf Coast. This does not mean that nearly all such wells drilled on the Gulf Coast now are of the slim-hole variety, but only that efforts have been aimed in that direction with very encouraging results and there has been a very definite trend to reduce the size of holes, a trend that probably will continue. As to exploration policy, there appear to be two distinct and opposite views. The one usually followed in the past was more or less designed to "shoot the works" on one well. Generally on the Gulf Coast, the depth at which production might be obtained is limited by the drilling equipment and economics. With this thought in mind, wildcat wells are often planned with the idea of carrying the depth to 10,000 ft., or even 15,000 ft. All of the possible hazards are anticipated and the general drilling and casing programs are so predicated. Such wells contemplate the drilling of large-diameter holes; the setting of at least one protective string of casing and an extensive coring policy, all of which finally adds up to an expensive well. As opposed to this general policy is the slim hole. This, on the Gulf Coast, recognizes that new discoveries represent gam-

Jan 1, 1941

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967