Search Documents

By B. A. Eaton, R. H. Jacoby

This paper presents the depletion-performance correlations developed using data from PVT studies and well-completion tests of 27 rich gas-condensate and volatile-oil reservoir fluids. The PVT behavior for each fluid war determined experimentally in the laboratory, and the depletion performance of each fluid was then calculated. Well-completion test data consisting of reservoir pressure and temperature, initial total gas-oil ratio, and stock-tank oil gravity were used with the depletion-performance data to develop general performance correlations. Three correlations are presented. The first equation shows the empirical relation of gas in place per barrel of hydrocarbon pore space with reservoir pressure and temperature, and initial total gas-oil ratio. The second equation is the correlation of stock-tank oil in place per barrel of hydrocarbon pore space. The third equation relates stock-tank oil production (to 500-psia depletion pressure) with pressure, temperature and oil gravity. All three correlations are also presented in convenient graphical form. Gas production to 500-psia depletion pressure is approximately 92.6 per cent of the gas in place for each fluid, so no correlation was developed for gas production. INTRODUCTION The rate of discovery of shallow, low-pressure and low-temperature oil reservoirs in the United States has been declining in recent years. For this reason, the search for oil has gone to greater depths where high pressures and temperatures are encountered. A high-pressure and high-temperature reservoir is the environment in which many rich gas condensates and highly volatile oils are found. Because of this trend, the performance prediction of such reservoirs has become an important task of the reservoir engineer. The need and usefulness of a performance correlation based on field data that are available from the usual well-completion tests have previously been established. These earlier attempts have shown that the phase behavior of rich gas-condensate systems and volatile-oil systems can be correlated with fluid properties, pressure and temperature. However, very little information on gas-condensate depletion performance5 was available at the time of these earlier attempts. The availability of more recent data has made possible the development of an improved correlation. The data, as listed in Tables I and 2, are for 25 gas-condensate and two volatile-oil systems that were studied. The problem was to correlate the data for in-place fluids and the production data with the initial total gas-oil ratio, initial reservoir pressure and temperature, and stock-tank oil gravity. These correlations were obtained by multiple regression analysis, whereby the data were fitted to an equation by the method of least squared error. BASIS OF THE CORRELATIONS 1. The data used in the development of these correlations were obtained from depletion-performance calculations6 and well-test or production measurements. 2. All of the independent variables used in the correlations are available from the usual well-test completion data. 3. The reservoir volume considered is 1 bbl of hydrocarbon pore space (HCPS). 4. The gas-oil ratio used is the total standard cubic feet of gas (at 14.7 psia, 60F) coming off the entire separator train per barrel of stock-tank oil. This minimizes the effect of separator conditions which might vary from system to system. 5. The correlated pressures are the actual reservoir pressures which might or might not be the saturation pressure of the reservoir fluid.

Jan 1, 1966

By P. R. Sperry, P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the inside texture of highly rolled aluminum and copper strips may be approximately described by four equivalent ideal orientations near (123) [121]. If rolled in reversed passes, the surface texture of copper is also near (123) [121], that of aluminum is (100) [011]. The inside texture of highly rolled brass is (110) [112]. The surface texture is the same, if rolled in reversed passes. The surface texture of all three metals is related to the inside texture, but asymmetrical, if rolled without reversal between passes. MANY previous investigations dealing with the subject of the present work were reviewed by Wassermann.1 Barrett,2 Brick,3 and Richards.' The recent introduction of quantitative methods for pole figure determination by Decker, Asp, and Harker,5 Schulz5 and others made it possible to reinvestigate some of the finer points which the earlier more qualitative photographic methods left undecided. The rolling textures of silver and of 70-30 cartridge brass have been quite consistently characterized by the ideal orientation of (110) parallel to the plane of rolling and [112] parallel to the rolling direction. On the other hand, it has been recognized by several investigators that certain other face-centered cubic metals, such as copper and aluminum, developed rolling textures rather different from that of brass. These textures have been variously described by the following ideal orientations, singly or in combinations with each other: (110 [112]: (112) [111]; (135) [335]; (135) [211], etc. The discrepancies usually have been attributed to the lack of sharpness in the textures and to the attendant difficulty of associating "ideal orientations" with pole figures showing great scatter of orientations. It seemed desirable to investigate by the new quantitative methods to what extent the apparent lack of sharpness may have been brought about by the qualitative methods used previously, rather than by the textures themselves, and to decide, if possible. between the various ideal orientations which have been proposed. Another problem, not satisfactorily settled by earlier investigations. concerns surface textures in rolled metals. For instance, in rolled aluminum the surface texture in some cases appeared to be similar to the texture inside the sheet, whereas in other cases it was reported to be entirely different.' The conditions under which such differences may have arisen, and the possibility of the occurrence of different surface textures in other face-centered cubic metals do not appear to have been examined in detail. The present work was undertaken to investigate the above questions. Some of the results obtained have been described- riefly. Experimental Procedure Specimen Preparation: In the present investigation 2s aluminum, electrolytic tough-pitch copper, and commercial 70-30 brass were used. These materials were available in the form of cold-drawn rods. 1 in. diam for tough-pitch copper and commercial 70-30 brass and 11/2 in. diam for 2s aluminum. The cold-drawn bars were alternately annealed and rolled 30 pct lengthwise in several cycles until a penultimate thickness of 0.500 in. was reached. The intermediate and the penultimate anneals were carried out for 30 min at 380°C with 2s aluminum, and for 30 min at 550°C with 70-30 brass. For tough-pitch copper, the intermediate anneals were 30 min

Jan 1, 1953

By S. A. Hovanessian

Analytical solutions are obtained for calculating the pressure distribution in rectangular fields due to injection and/or producing wells located anywhere within the field. The field is assumed to be homogeneous with either constant pressure or no-flow boundaries. These solutions are extended to include the calculation of average reservoir pressure and permeability from pressure build-up curves. Numerical examples are given to illustrate the application of equations to practical problems. INTRODUCTION Pressure distribution analyses are of considerable importance in the field of reservoir mechanics. A number of papers dealing with this subject have appeared in the petroleum literature. perrinel in 1956 presented a summary of the methods available for pressure build-up calculations and discussed the applicability of each in some detail. More recently (1958), Hazebroek, et a1,2 discussed a theoretical method for obtaining pressure distribution in a radial field. Also in 1958, Nisle3 gave a theoretical solution of the pressure distribution in a field extending to infinity with a partially penetrating line source at the origin. Mathews, et a1,4 applied the method of images to existing solutions for pressure distribution in radial fields and obtained expressions for calculating pressures in bounded reservoirs. However, a literature survey revealed that a general analytical solution for the pressure distribution in a rectangular field, with injection and/or production wells located anywhere within the field, was not available. Such a solution could be used to approximate the pressure distribution in a field the shape of which is nearly rectangular. Furthermore, it could be applied to pressure calculations pertaining to a single well taken from a system of wells which were drilled in a rectangular pattern. In this case the boundaries of the well drainage area are considered to be the perpendicular bisectors of the lines joining the well and its nearest neighbors. The basic problem considered in this paper consists of a rectangular field with either constant-pressure 01 no-flow boundaries and with either an injection or production well located anywhere within the field. The physical properties of the rock and fluids present are considered to be constant. Analytical expressions are obtained for the pressure distribution within the field during the production or injection periods. These expressions, which are infinite series, can be used to evaluate pressure at any point within the field as a function of time and position. For fields containing more than one well (production and/or injection), the solutions for each well acting independently are superposed. That is, at any point in the field, the pressures due to each injection 01. production well acting alone can be algebraically added to give the pressure resulting from all wells acting simultaneously. Evaluation of the series solutions given in this paper is readily accomplished by means of an electronic digital computer; and, in most cases, sufficient accuracy is obtained by setting the upper limits of summation at 20. These solutions are extended to include the calculation of average reservoir pressure and permeability from build-up data. A number of numerical examples are given to illustrate application of the solutions to actual field problems. ANALYTICAL SOLUTIONS The partial differential equation representing the pressure distribution in a homogeneous rectangular field (see Fig. I.), having a single source or sink of strength (2, can be written*

By J. Chipman, N. J. Grant, R. Rocca

Desulphurization of liquid iron by reducing slags of the electric-furnace type was studied from 65 heats. Variations were made in basicity over a wide range and in FeO up to about 5 pct for their effects on desulphurization. The role of FeO in desulphurization from the blast furnace, to the electric furnace, to the oxidizing conditions of the open hearth is shown to fit a relatively simple pattern of behavior. THE mechanism which controls the desulphurization of molten iron by basic slags has been the object of several investigations. In particular, equilibrium determinations have been made both in the field of basic open-hearth slags, which have a high iron-oxide concentration, and in the field of blast-furnace slags which have a very low iron-oxide concentration. In both cases the desulphurization ratio has been found to increase with increasing basicity of the slags; however, the mechanism of desulphurization differs in the two cases. In basic open-hearth slags desulphurization occurs mainly as a partition of iron sulphide:&apos; FeS * (FeS) and the desulphurization ratio is approximately independent of iron-oxide concentration in the slag. In blast-furnace slags the concentration of iron oxide is very low as a result of the highly reducing conditions in which they are formed. The controlling reaction for desulphurization is then:2,3 FeS + (CaO) <=* (CaS) + (FeO) The slags of the reducing stage in the electric furnace have an iron-oxide concentration which is intermediate between blast-furnace and open-hearth slags. The study of the mechanism of desulphurization for these slags has been the object of this investigation. The importance of low (FeO) in the slag for desulphurization was first verified by Bardenheuer and Geller,& who found that high desulphurization ratios were obtained in highly reduced slags. It was recognized" hat iron oxide in the slag becomes a controlling factor in desulphurization only at FeO concentrations approximately under 5 pct. A recent investigation conducted by Buehl,7 upon the suggestion of one of the authors, confirmed this opinion from the results obtained from a heat conducted in a small arc furnace. In the present investigation, slags of very high basicity, such as often are encountered in the basic electric furnace, could not be studied, but equilibrium data have been obtained for slags in a wide basicity range. The iron-oxide concentration in these slags ranged from 0.08 to 15 pct and was controlled by the addition of silicon to the metal. Other constituents of the slags were mainly CaO, MgO, SiO2, A120,, and CaF,. The experimental technique was essentially the same as that of previous investigations.1 8-lo In an open magnesia-lined induction furnace, 65 lb of Armco ingot iron was melted. An atmosphere of hydrogen was maintained over the melt for 1 hr to bring the carbon content down to approximately 0.010 pct maximum. The bath then was exposed to air for 25 min to remove hydrogen. The electrodes were put in place, and the furnace was operated from this point on in an atmosphere of nitrogen. A synthetic slag was added to which additions of silicon and iron sulphide were made. A rate study conducted at the beginning of this investigation had

Jan 1, 1952

By Stephen Zorn

INTRODUCTION The process of financing mining projects in developing countries has changed greatly in the past 15 years. New methods of financing, notably the use of syndicated Eurocurrency project loans, have appeared, and direct equity financing by transnational mining corporations has become less significant. These changes are of particular importance to developing countries which have many mineral deposits still awaiting development, or even discovery. If major new mines are to be financed, host governments will need to obtain more sophisticated information than has hitherto been widely available as to the various sources of finance currently available and as to possibilities for innovative approaches to financing, such as the combination of several different kinds of financing in a single package. This paper reviews the major sources of mining finance potentially available to developing countries and highlights those problems in obtaining adequate financing that developing country producers have begun to experience in the last few years and that are likely to persist through the 1980s. Section I surveys the major types of mining finance; section II reviews specific financing problems, including (a) the withdrawal of the transnational corporations from developing countries, (b) inflation and the size of new projects; (c) developing country indebtedness, and (d) competition among projects in different countries. SOURCES OF DEVELOPING COUNTRY MINING CAPITAL1/ There is a wide range of financing mechanisms which are potentially available to developing countries with economically viable mining projects., Moreover, these financing mechanisms have not been fully exploited by developing countries, and more aggressive pursuit of financing by the governments of these countries may well reveal greater possibilities in respect of any particular project than may initially have appeared. However, virtually all the funds available from these sources are available only to projects which meet the standards of viability acceptable to lenders and others in the business community. If a project does not, for example, promise to generate a discounted cash flow rate of return of at least 15 per cent on total funds employed, or if it does not appear likely to generate sufficient cash flow in the early years of production to cover debt service requirements with a comfortable margin in reserve, most of the sources of financing will not be available. Only where a government has its own financial surplus (as in the case, for example, of the industrialization program of the Saudi Arabian government) can it effectively undertake projects which do not satisfy the definition of economic viability that is accepted at any given time by the worldwide financial community. Internal Sources In Developing Countries Internal financing capacity in developing countries is restricted to a relatively small number of countries - typically those large enough to support a well-rounded industrial sector, in which mining is only one of a number of dynamic industries. While there are large mining companies in certain other countries, the ability of such companies to finance new projects (or even, in some cases, to generate the cash necessary to maintain existing levels of production) is highly problematical. Within developing countries, the possible sources of internally-generated mining finance are the following: (1) state-owned enterprises; (2) private capital; (3) the banking system, and in particular those financing agencies that have a special involvement with the mining sector; and (4) direct budgetary appropriations.

Jan 1, 1985

By C. S. Matthews, M. J. Fischer

Distortions caused by dip on five-spot sweep pattern were determined by visual experiments on a model composed of parallel plates of glass with holes drilled at the well positions. This model war designed to simulate a reservoir depleted of its primary oil and containing a gas phase. Prior to interference, it was found that the injected fluid took a nearly circular shape about the injection well for the cases studied. However, these circles moved down-dip considerably under the influence of gravity. It was concluded that pattern flooding should be practical for many dipping reservoirs. A quantitative measure is given of how much the well position should be altered to allow for dip. Experimental deternzinarions of injectivity showed this to be about the same in a dipping reservoir as in a horizontal one. INTRODUCTION This investigation was undertaken at the suggestion of the Pacific Coast area, Shell Oil Co., where a pilot water flood in a dipping reservoir was being carried out at the time this paper was in preparation. Prior to the undertaking of this flood there had been considerable speculation as to how gravity would distort a flood pattern in a dipping reservoir. The thought was expressed in some quarters that a five-spot flood would not be applicable to a dipping reservoir because the flood pattern would elongate in the direction of dip and would never form a "seal" around each five-spot. If the flood pattern elongated sufficiently, both the oil and the water might flow largely downdip rather than into the pattern producers. In view of the importance of the California water floods, it was deemed important to determine the effects of gravity on a five-spot pattern in a dipping reservoir. Previous work had also been carried out in this laboratory,1 but only for the single-fluid case. The present investigation extends these results to multifluid cases. Several sets of pictures of flood fronts are presented so that the process can be visualized. From these pictures, curves are obtained which show the correct drilling position for achieving equal times of oil-bank breakthrough. Several injectivity curves are also presented which may aid in prediction of injection rate. ASSUMPTIONS The present results were obtained with a model composed of two parallel plates of glass spaced about 1 mm apart. When the inertial forces are small, as in these experiments, the flow between the plates follows Darcy&apos;s law and is analogous to flow through porous media. In using these plates, it is not possible to scale effects of capillarity correctly as regards a transition zone between injected and displaced fluid. Calculations show, however, that effects of such capillarity should not be important in determining the gross flooding pattern in the field. In fact, in this model the capillary forces tend to circularize the pattern to a greater degree than in the field. To preserve a large ratio between the viscous forces and the circularizing capillary forces in the laboratory model, viswus glycerine was used as the flooding liquid and the rate of flooding was very high. The circularizing force is believed negligible in these experiments. In addition to the effect of the surface tension y, which tends to circularize the pattern, another capillary force must be considered. This is the adhesion tension y cos, which acts at right angles to the circularizing term y. If the plates in the model are "wetted" the same all around the periphery, then the adhesion tension,

Jan 1, 1957

By C. K. Eilerts, J. D. Ham

Laboratory research has been conducted to evaluate the characteristic effects of condensate saturation on the mobility of gas in typical reservoir rocks. A pump with two pistons provided phases in equilibrium at controlled flow rates and constant liquid-vapor volume ratios. Core samples were tested in a holder that permitted sealing steady-state phases in the pore spaces under flow test pressures for weighing with sufficient precision to give an accurate measure of the attained saturations. Parameters of the study were pressure, apparent velocity, flowing liquid-vapor volume ratio, fluid composition, core material and length-to-diameter ratio. Tests were conducted at 515 and 1,515 psia to determine the effect of pressure on the mobility-saturation relationship. Influence of the apparent velocities 0.30, 0.15 and 0.07 cm/sec and of five liquid-vapor volume ratios from 0.0001 to 0.01 was determined at 515 psia The principal fluid system was nitrogen and and separator liquid from a Gulf Coast condensate, but the effect of a condensate of different viscosity was also determined. The significance of a possible concentration of liquid near the outlet end of the test cores was investigated. Core materials included a consolidated sandstone and a low-permeability limestone. Relative mobility and liquid-vapor volume ratio relationships are concluded to be dependent on pressure, saturation and, to a lesser extent, on velocity. For each porous medium and fluid there is a minimum saturation essential to two-phase flow, and high velocities of flow have only limited effect on saturations in this range. INTRODUCTION It is now recognized that knowledge of the availability of a reservoir gas — the period that gas may be recovered from a reservoir at a given rate — is as important as the estimate of gas in place. When reservoir conditions are such that pressure decline owing to production will result in retrograde condensation, liquid saturation can increase in the structure around the production well in a way that may restrict flow capacity, and hence future availability. l Based on a numerical solution of transient radial flow of single-phase gas-condensate fluids, 2 a program for computing the accumulation of condensate in a reservoir and the effect of this condensate on deliverability has been developed. During this development a need evolved for data that described the influence of pressure, velocity of flow and condensed liquid on mobility as recovery progressed. This paper presents the results of experimental investigation to obtain insight into the mobility relationship at reservoir pressures of gas-condensate fluids. A core holder for flow tests at reservoir pressure was developed to weigh the core and its fluid contents under pressure to determine saturation. A specially constructed pump was used to drive a two-phase fluid through the core until a steady state prevailed. The core was used as a differential device, and properties measured were intensive rather than extensive. APPARATUS Fig. 1 shows a schematic representation of the major pieces of equipment used in the mobility determination. The weighable core holder is connected to a two-piston, constant-displacement pump. Attainment of steady-state flow is indicated by stability of the flow differential read from the high-pressure manometer. WEIGHABLE CORE HOLDER An important part of the data needed was the mobility-saturation relationship. This required that mobilities and saturations be measured at pressures, flow velocities and liquid-vapor volume ratios characteristic of condensate reservoirs.

By H. I. Aaronson, C. Laird

Cold rolling by 50 pct a A1-4 pct Cu alloy containing many 0&apos; plates has been found to accelerate markedly the transformation of 8&apos; to 0 upon further aging. Although the basic mechanism of this transformation remains unchanged by plastic deformation, the nuclea-tion kinetics of 8 become appreciably more rapid and also less dependent upon temperature. Particularly at lower aging temperatures, rounded idiomorphs replace several faceted rnorphologfes. The rates of growth of 9 idiomorphs in deformed specimens aged at 300°C are appreciably more rapid than simple volume diffusion control allows. This observation is shown to be explained by an excess vacancy, rather than by a dislocation Piping mechanism of growth. ThE rather complex phenomenology of the 8&apos; —8 transformation in Al-Cu alloys has been recently elucidated in considerable detail by means of transmission electron microscopy.&apos;-4 This technique was also employed in the present investigation in order to examine the effects of plastic deformation upon the transformation of 8&apos; to 8. The mechanism of the transformation in undeformed Al-Cu alloys has been established as the following sequence of events.1"4 The first step is the nucleation of 9 at (Y:8&apos; boundaries. Nucleation of a 0 crystal takes place, however, at only a very small proportion of the 8&apos; plates present. Each 0 crystal simultaneously consumes the host 8&apos; plate and the a! in the immediate vicinity, with growth into a being the rate-controlling process. The remaining 8&apos; plates are then dissolved as they fall under the concentration shadow of the growing 8 crystals. The evidence on the effects of plastic deformation upon these processes is intriguing, but much less detailed. The careful X-ray studies of Graf and Guinier have shown that the aging times required to form detectable amounts of 8&apos; and 8 are reduced by prior cold working. Thomas and Nutting confirmed these results by replication electron microscopy. Nile-shwar,* on the other hand, reported that creep deformation decreases the rate of formation of 0. While this difference may have been caused by the use of concurrent rather than successive deformation and ag- ing, the X-ray technique which he used was able to monitor only the 0 phase. It is thus possible that the times needed to form 8&apos; were increased moreg than the kinetics of 8&apos; — 8 transformation were accelerated. At 90 pct deformation by cold rolling, Graf and Guinier found that the usual 0&apos; —0 8 sequence is reversed: 0 forms first. von Heimendahl 10 confirmed this result with transmission electron microscopy. Pollard and Nutting, 11 and more recently Driver and Barrand, 9 having used the same technique, report that 9 also forms first during creep deformation. In the present study, the maximum amount of deformation was limited to 50 pct reduction by cold rolling in order to insure that 8 formed principally by the decomposition of . I) EXPERIMENTAL PROCEDURES This investigation was conducted on an Al- 3.93 pct Cu alloy, prepared as previously described. 4 Morphological and crystallographic effects of plastic deformation were studied in specimens annealed 6 hr at 548°C, quenched, and then aged for either 3 or 8 hr at 250°C to form large numbers of 0&apos; plates. After cold rolling to a 50 pct reduction in thickness, the

Jan 1, 1969

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low grade molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported. In the chlorination process, a gaseous mixture of chlorine and oxygen in the volume ratio bf 2:5 has been passed at 1.66 x 10- 5 m3/s for 1800 s over a 0.01 kg batch of molysulfide concentrate at a temperature of 573°K. Most of the molybdenum has been volatilized as molybdenum oxychloride which has subsequently been extracted in water. The molybdenum value from the aqueous solution has been recovered in the form of calcium molybdate (CaO.MoO3) by treatment with calcium chloride (CaCI2). In an alternative processing scheme, the molybdenum rich solution has been treated with an oxidizing agent (K2S20f.J) and allowed to boil to recover a major portion of the molybdenum value in the form of molybdic oxide (MOOS). The spent charge obtained after molysulfide chlorination has been mixed with about 1 wt % sodium chloride and heated at 773K under an oxygen atmosphere. The reacted mass has been water-leached to yield a nickel-copper bearing solution with limited iron. The process liquor appears to be well suited for further processing by known hydrometallurgical recovery processes for nickel and copper. In the conventional process of molybdenum extraction, the molysulfide concentrate (-59% Mo) is first subjected to roasting to produce molybdic oxide. The oxide is then further processed in sequential steps involving vacuum distillation, ammonia leaching, and calcination to higher purity prior to hydrogen reduction to metal. In India there is at present some small tonnage production of molysulfide concentrate from a byproduct recovery plant of the M/s. Uranium Corp. of India Ltd. (M/s UCIL), Bihar. Efforts are being made at this laboratory to process the low grade fraction of the concentrate which contains sulfides of copper, nickel, and iron; quartz; and chlorites. Here, the conventional routes involving roasting and vacuum distillation appear unsuitable to produce an acceptable quality of molybdic oxide at high recoveries. Formation during roasting molybdates of some of the impurities present in the sulfide concentrate make subsequent vacuum distillation less efficient. In view of these problems, in earlier work reported from this laboratory the low grade concentrate has been processed hydrometallurgically to P. produce calcium molybdate. Starting from this molybdenum intermediate, processes have also been developed for the production of molybdenum and ferromolybdenum. Chlorination as an alternative to roasting for metal sulfides has been drawing considerable interest. The high reactivity of chlorine, the relatively low temperature of operation, the suitability of application to low grade resources, the convenience of recovering sulfur in non-polluting form, and the purity of chlorides which are separated by distillation all favor chlorination. In recent years, considerable work has been reported on the chlorination of common metal sulfides. In the field of molybdenum extraction from its sulfide resource, use of chlorination technology has been rather limited. Senderoff and Labrie3 were the first to chlorinate molysulfide concentrate with elemental chlorine at about 823°K to molybdenum pentachloride for use in the electrolytic preparation of molybdenum. The only other reported work, by Haver, Uchida and Wong, involved reaction between molysulfide and chlorine at 673°K to recover sulfur. The reaction products were, however, identified as molybdenum pentachloride and sulfur monochloride.

Jan 1, 1979

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author&apos;s laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968

By C. H. Gorski

A method for preparing titanium tetrachloride is described which consists of reducing rutile with coke and chlorinating the reduced product at 200° to 500°C. The crude distillate is purified by treatment with copper powder and distillation. Recoveries, exceeding 90 pct of the titanium in the rutile, were obtained. IN recent years considerable interest in metallic titanium has been aroused because of its outstanding physical and chemical properties. The present commercial processes for preparing titanium are modifications of the Kroll1 process and consist essentially of the reduction of titanium tetrachloride with magnesium in an inert atmosphere to produce metallic titanium with magnesium chloride as a byproduct. At present,&apos; commercial titanium tetrachloride costs $0.32 a pound, which makes the price of the included titanium $1.28 a pound. As the titanium tetrachloride must be purified further before processing into metal, its ultimate cost obviously will be higher. Consequently, one of the prime requisites for the production of lower cost titanium metal is a source of low-cost titanium tetrachloride. Recently, Knickerbocker, Gorski, Kenworthy, and Starliper3 escribed a method for preparing titanium tetrachloride from low-grade Arkansas rutile by smelting the rutile with pyrite and coke to form a titanium matte and then chlorinating the titanium matte to prepare a crude titanium tetrachloride. This process had several inherent advantages. Low-grade rutile concentrates were utilized, the chlorination temperature was relatively low (approximately 200°C), and the reaction was strongly exothermic. However, this process had several disadvantages, chief of them being the rather low recoveries of titanium tetrachloride (65 to 81 pct) and the difficulty in purifying the crude titanium tetrachloride obtained. Because of the high-titanium and low-iron con- tents of rutile as compared to ilmenite, rutile should be of greater potential value as a source of titanium tetrachloride than ilmenite. Rutile, however, is not chlorinated directly in commercial practice, because reaction temperatures above 700 °C are required, at which point chlorine attacks most of the common materials of construction. The process now in use consists of converting the titanium in rutile to the cyanonitride by high-temperature reduction in an electric furnace, and then chlorinating this compound. The disadvantages of this process are the difficulty of producing the cyanonitride, the use of high-grade rutile concentrates in the charge, and the presence of several percent of silicon tetrachloride in the finished product. It would be of considerable interest to develop a new process for the preparation of titanium tetrachloride from rutile by chlorination at 200" to 500°C. Process Development Several investigators&apos;-&apos; have studied the reduction of titanium dioxide with carbon in an effort to prepare titanium monoxide. Invariably, the titanium monoxide formed in this manner was not pure, as it contained titanium carbide and one or more of the lower oxides of titanium. As these lower oxides of titanium are more reactive chemically than rutile, and as it is known that titanium carbide may be chlorinated readily, a study was made of the chlorination of carbon-reduced rutile. A sample of rutile concentrates from Hot Spring County, Ark., containing 76.19 pct TiO,, 5.65 pct Fe2O3, 4.18 pct SiO2, and 2.88 pct Al2O3, was used for this investigation. The experimental procedure consisted of making an intimate mixture of —100-mesh rutile and petroleum coke, adding water and molasses as a binder to foi-m a paste, charging into a graphite crucible that was covered, except for a vent to allow the

Jan 1, 1952

By C. F. Weinaug

In recent years, several methods have been proposed for correlation of physical properties and behavior of hydrocarbon systems. These correlations were found to be unsatis. factory for predicting differential gas liberation and shrinkage data now obtained experimentally. To achieve the desired accuracy, methods were developed to adjust the correlations with two experimental pieces of data. The required data are the saturation pressure at reservoir temperature and the specific volume or density at these conditions. The saturation pressure is used to adjust the vapor-liquid equilibrium-ratio correlations. The density measurement is used to determine the apparent density of liquid methane. With these adjustments, differential gas liberation and shrinkage are predicted within the experimental error. EQUILIBRIUM RATIOS Equilibrium ratios published by the National Gas Assn. of America&apos; were used as a basis for the calculation. The convergence pressure for the sample was determined by using a hypothetical binary system, with methane as one component and the remainder of the system lumped together to form the other component. For the critical temperature of the heavy constituent, the weight average of the critical temperatures of the ethane and heavier components was used. The correlation of pseudo-critical temperature, density and molecular weight of Matthews, Roland and Katzl was used in this calculation for the hexane and heavier fractions. Points for the critical properties of methane and the hypothetical heavy constituent were placed on a chart of the critical loci of hydrocarbon systems. A critical loci for the hypothetical binary system was drawn, and the critical pressure of this system was determined at the reservoir temperature. This critical pressure became the convergence pressure for which equilibrium ratios were read from the NGAA4 charts. The NGAA equilibrium constants for C, through C, were used for the C,; through C, fractions since they were separated on the bases of normal paraffin boiling points. The correlation of Hoffman, Crump and Hocott5 as used to estimate the equilibrium constant for the C fraction. The NGAA eauilibrium-ratio charts are based primarily on paraffin systems and have to be corrected for the presence of naphthenes and aromatics. The correlations in the literature proved too unsatisfactory for determining these corrections. EXperimental data, the saturation pressure, is used with the correlation of Soloman2 to make this adjustment. The correction factors of Soloman were cross-plotted so that the factors for ethane and heavier components were made a function of the factor for methane. a2 = 0.7927 at + 0.1646 .........(1) where a, = correction coefficient for for methane NGAA equilibrium ratio, and a2t = correction coefficient for ethane and heavier NGAA equilibrium ratios. This equation and the equation for the bubble point are solved simultaneously for the correction coefficients. The bubble-point equation is anKnXn = 1.0 . . . . (2) The equilibrium constant for the saturation pressure at reservoir temperature is used. This procedure not only corrects for the relative volatility between components, but also assures that the results will be directly related to the experimental saturation pressure. METHANE DENSITY After determining a set of equilibrium ratios, the apparent density of condensed methane at 60°F and 14.7 psia was estimated. This was found to be necessary because the correlations of Standing3 ere found to be unsatisfactory. The law of additive volumes was employed to make this calculation.

By Ronald W. Klusman, Erik B. Nelson

The Front Range portion of the Colorado Mineral Belt is an extensive area of mineralization with mining activity dating from 1859 with the discovery of large gold deposits. After an initial boom period and gradual diminishing production, present activity is restricted to molybdenum in Clear Creek County, uranium in Jefferson County, and several small operations extracting gold and silver in Clear Creek and Gilpin Counties. Gold and silver have dominated the production in the Front Range, though the complex mineralization created milling and smelting problems and it is postulated that considerable amounts of precious metals remain in the mine dumps. This area is plagued by a severe mine drainage problem, with Clear Creek most impacted by many draining mines and tailings in the basin. Boyles et al. Moran and Wentz, Wentz, Wildeman et al., have examined various aspects of the impact of mine drain¬age in the Clear Creek basin. The primary objective of this study was to collect data on the tailings, drainages, and leaching experiments in order to make preliminary suggestions for reducing the impact while recovering metal values to offset treatment costs. A variety of leaching experiments were performed on tailings from the Nevada Gulch area in the Central City mining district. Leachings were performed in vertical tubes indoors and wooden boxes exposed to the outside environment. In the leaching experiments, the leaching solution, grain size, and residence times were varied, while forced aeration was used in some experiments. Bacterial nutrient 9K° and mine drainage were used in some of the experiments. A total of 14 additional tailings samples were analyzed for base and precious metals. The composition of the mine drainage and tailings used in the leaching experiments, as well as data on the additional samples are shown in [Table 1]. Leachate samples were taken periodically for analysis until compositions leveled off. Results and Discussion Leaching with distilled water was used as a control and best illustrates the basic behavior of the leaching process for zinc in a vertical tube [(Fig. 1)]. More acidic leachings increased concentrations of metals as did smaller grain sizes, though the time required increased significantly. Mine drainage with its high concentration of dissolved iron sometimes decreased the heavy-metal concentration in the leachate due to oxidation of Fe 2 and precipitation of Fe(OH)9 which absorbs some of the dissolved heavy metals. In the larger scale experiment carried out in the simulated leaching pad, substantial concentrations of metals were attained in the final leachate after one month. In this experiment the leachate was not recycled, but allowed to saturate the tailings continually with evaporation loss made up by additions of Quartz Hill drainage and nutrient 9K. The concentration of the metals in the leachate and the increase over the input solution are given in [Table 2]. Heap leaching of low-grade copper and uranium ores is successfully carried out in many districts, enhanced by the metabolism of autotrophic bacteria of the Thiobacillus-Ferrobacillus group. These ubiquitous organisms enhance metal leaching, and general aspects of heap leaching are discussed by Malouf, Trudinger, Pings, and Duncan et al. Conclusions and Recommendations Returning to the primary objective, how to reduce the mine drainage impact and recover metal values, we need to consider how the data may suggest avenues toward this objective. Boyles, et al., considered various

Jan 1, 1977

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year&apos;s total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state&apos;s well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma&apos;s producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year&apos;s total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world&apos;s deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year&apos;s total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state&apos;s well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma&apos;s producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year&apos;s total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world&apos;s deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By K. R. Janowski, A. B. Chase, E. J. Stofel

Ruby crystals of exceptional optical quality have been grown from fluxes composed of Bi2O3 + PbF2 or Bi2O3 + BiF3. Careful control of growth conditions was required to minimize the number of growth defects consisting primarily of dislocations, occluded flux, and growth twins. Slow growth rates coupled with the addition of small amounts of La2O3 as a flux dopant were helpful in producing nearly perfect crystals. Chromium concentrations up to 1 pet were incorporated into these crystals without adversely affecting their perfection. Crystals up to 10 mm in diameter having as few as one to ten dislocations per crystal were typical of those produced under optimum growth conditions. Under these same conditions the occlusions were eliminated, and growth twins were either eliminated or reduced to one to three twin boundaries per crystal. INTEREST in the nature of lattice imperfections produced during the growth of ruby crystals (Al2O3-corundum structure) has been stimulated recently by the need for ruby lasers of good optical uniformity. As a result, ruby crystals grown by the flame-fusion (Verneuil) process have been studied in detail and have been found to contain high densities of dislocations (106 to 107 dislocations per sq cm) and mosaic structures that impair their optical quality.&apos;-3 Attempts to improve the quality of Verneuil-grown crystals by controlling the growth variables have not been entirely successful. On the other hand, rubies grown by the flux process have received little attention even though their more nearly equilibrium growth conditions suggest that they would have fewer growth defects. Nelson and Remeika have shown recently that small flux-grown rubies can indeed be made into very low-loss lasers. However, they did not report information on crystalline imperfections in these crystals.4 Stephens and Alford have reported briefly on defects found in a flux-grown corundum crystal but they neither described these defects in detail nor related them to the method of growth.5 The present investigation was undertaken to establish the relationship between growth conditions and crystalline perfection of flux-grown rubies, sapphires, and other crystals of the corundum family. EXPERIMENTAL PROCEDURE The corundum crystals used in this study were grown by slowly cooling solutions of A12O3 in molten-salt solvents of PbO + PbF2, Bi2O3 + PbF2 or Bi2O3 + BiF3. The materials employed were Linde A (a Al2O3 powder) with reagent-grade chemicals as solvents. Some of the solutions also contained small additions (1 pet or less) of one or more of the transition metal elements chromium, manganese, iron, and titanium as crystal dopants. La2O3 was added to some of the solutions to alter the growth habit of the crystals. The La2O3 promoted the occurrence of growth facets parallel to (0112) and {1011} planes, where the indexing system is the morphological system described in detail by Kron-berg6 and used throughout this paper. The melts from which the crystals were grown were prepared by mechanically mixing the various constituents and placing them in platinum crucibles. The covered 50- and 100-ml platinum crucibles were heated in muffle furnaces at 1250°C for short periods of time (1 to 4 hr) and then program-cooled at either 2° or 4°C per hr to 1000°C. At this lower

Jan 1, 1965

By Irving B. Cadoff, Ernest Levine

The fracture path in a Cu-4 pct Ag alloy wet with mercury was found to he dependent on the heat treatment used prior to tensile testing. Both quenched and slow-cooled alloys were embrittled by the mercury.. For quenched alloys, which were single -phase, the crack path was intergranular. Slowly cooled alloys, which contained precipitate platelets, exhibited transgranular fracture. By comparing stress-strain data for these alloys with similar data on mercury -embyittled solid-solution alloys, it was found that the role of the precipitate and that of the grain boundary in the fracture process were equivalent . THE fracture path which results when metals are strained in a liquid environment appears to be dependent upon the nature of the specific system. Mixed transgranular and intergranular cracking has been observed in the 2024 T4 aluminum alloy when wet with a Hg-Zn amalgam.&apos; Transgranular fracture was induced in an A1-4 pct Cu alloy by masking off the grain boundaries from the liquid Hg-Zn amalgam.&apos; The embrittlement of solid-solution alloys of copper in mercury results in intergranular fracture.&apos; The effect of a precipitated phase on the fracture path in copper alloys is the subject of the present investigation. Cu-4 pct Ag was chosen so that its behavior could be compared with previous work on embrittlement of copper alloys. PROCEDURE High-purity copper (99.999 pct) was used as a base metal, along with 99.999 pct purity silver. Melting was carried out in graphite crucibles with manual agitation to get adequate mixing. The ingots were homogenized by means of vacuum annealing, chemically cleaned, and cold-rolled with intermediate vacuum anneals, to the desired thickness of 0.025 in. The rolled sheets were sheared to the final specimen size of 1 by 0.025 by 0.1 in. The specimens were then electropolished in phosphoric acid (concentrated) and heat-treated in an evacuated capsule at the solution temperature of 770°C. One batch was slow-cooled and the other quenched in water. The thermal etching which occurred during heat treatment was sufficient to permit grain boundary and precipitate delineation. Tensile tests were carried out in air and in mercury on a Table-Model Instron at a pulling speed of 0.2 in. per min. Wetting was accomplished by electro-polishing in phosphoric acid, rinsing in alcohol, and immersing in a pool of mercury. Once wet the coating was stable throughout the mechanical tests. In our studies it was found that wetting the surface or total immersion in mercury produced identical results. For convenience, the wetting technique was used for the experiments described. The crack pattern was observed directly on the surface by removing the mercury after testing. De-wetting was accomplished by flame heating the samples in a vacuum after testing and before observation of the surface. No etchant or polishing was used so as not to obscure the crack pattern on the surface. The mercury removal, however, resulted in a pitted surface but otherwise left the pertinent features visible. Photomicrographs were taken in this condition so as not to disturb the structure associated with the crack pattern. The average precipitate spacing was measured previous to coating the sample with mercury by use of an optical eyepiece micrometer. RESULTS The microstructure of the quenched specimens was single-phase while that of the slow-cooled specimens contained thin platelets of a second

Jan 1, 1964

By B. H. Kear

Clustering of slip bands in different systems has been observed in both ordered and disordered Cu3Au crystals compressed in the <110> orientation. Certain features of the slip band patterns are explained in terms of reactions between dislocations with Burgers vectors at 120 deg; in a few rare cases, the slip band evidence suggests that the Products of such reactions form diffuse tilt boundaries between the differently slipped regions of the crystal, similar to the known behavior of ionic crystals, but not nearly so well defined. WHEN crystals with orientations favorable for multiple slip undergo plastic deformation, slip may occur in different systems in localized regions, so that clusters of slip bands are developed. This phenomenon has been observed in fee1-4 metals and also in ionic crystals having the sodium chloride structure.5-8 In the ionic crystals, the boundaries formed between the differently slipped regions of the crystal assume characteristic orientations and are associated with macroscopic tilts that are plainly visible on the sides of the crystal. Recently, this interesting feature was explained in terms of the formation of diffuse low-angle boundaries as a result of interactions between families of glide dislocations in the different systems meeting in the boundaries.9 This paper describes an attempt to obtain similar evidence for boundary formation in an fee crystal. The alloy Cu3Au was chosen for the present study simply because this material is currently being used in a general study of differences in deformation behavior of the ordered and disordered phases of this alloy, which will be described elsewhere. EXPERIMENTAL PROCEDURE The two specially oriented compression specimens used in the present study were prepared from a melt-grown single crystal by careful cutting, grinding and polishing. The finished specimens were about 6 mm by 2 mm in cross section by 6 mm tall, with their ends parallel to (101) and sides parallel to (111) and (121); the broad faces of the specimens were made parallel to (711). Both specimens were annealed in an evacuated quartz tube at 850oC for several hours, slowly cooled to 500°c, and then quenched into water in order to obtain the disordered state for the alloy. One of the specimens was partially ordered (with S- 0.8) by reannealing at 350oC for 100 hr. After these annealing treatments, both of the specimens were electropolished. 10 Finally, the specimens were compressed in the [loll orientation and their stress-strain curves were recorded. The deformation was carried out in increments of a few percent strain. At each stage in the deformation the specimens were unloaded, removed from the compression jig, and examined optically for slip bands. Before reloading, the specimens were repolished, so that the observed slip band patterns were characteristic of a particular stage in the deformation. EXPERIMENTAL RESULTS Fig. 1 show!; the stress-strain curves for the ordered and disordered specimens and also indicates the stages 1, 2, and 3 where the deformation was interrupted for examination of slip bands. The curves show marked differences in flow stress and in work hardening rate in the two specimens, as observed by previous workers.11,12 Also, it was found, in agreemement with the observations of Taoka and Sakata,&apos;3 that the plastically deformed disordered alloy showed the characteristic coarse slip bands of alloys, whereas the ordered alloy exhibited a fine slip band structure similar to that of pure metals. Slip Band Observations. In what follows, the description of the slip band patterns, with accom-

Jan 1, 1962

By N. Mungan, J. L. Thompson

Laboratory displacement tests were performed to study oil recovery elficiency by gravity drainage in fractured systems under miscible conditions. The porous media used were cylindrical Berea and Blue Jacket sandstone cores containing a number of well-defined, artificially formed, vertical and subvertical fractures. Butane and Soltrol 130 were the two miscible fluids used. The purpose of the study was to examine the influences of the displacement rate, fracture density, fracture orientation, fracture permeability, matrix permeability, crossflow, core length and connate water on the oil recovery. It was found that displacement rate, matrix permeability and the subvertical fractures affected oil recovery most. The critical flow rate, based on the matrix permeability, was found to be a significant factor in the process. For displacement rates below the critical flow rate, the oil recovery efficiency appeared to be unaffected by the density of the subvertical fractures. At the high displacement rates, the fracture density becomes important, with the recovery being the most efficient in the core having the greatest number of the subvertical fractures. The magnitude of the fracture permeability, the fracture orientation, the core length and the connate water have little effect on the oil recovery efficiency. INTRODUCTION Gravity drainage under miscible conditions from relatively thick reservoirs can be a very efficient recovery process, especially at low flow rates where the gravity forces are dominant and, consequently, the adverse viscous fingers associated with the unfavorable viscosity ratio are minimized or eliminated. Such a process might involve injection of an LPG or some solvent bank at the crest and then driving the bank with dry gas. For some favorable combination of reservoir temperature, pressure and oil composition, there may be no need to inject any solvent bank, since enrichment of the dry gas by the light ends of the crude creates an in-situ solvent bank. Slobod and Howlett2 have studied the effects of gravity segregation in vertical unconsolidated porous media under miscible conditions in the laboratory. The main variables in their study were the viscosity ratio, the density differences and the rate of flow. In this study, the objective was to find the influence of fractures on gravity drainage under miscible conditions. A greater number of related variables were also studied. LABORATORY STUDY CORE DESCRIPTION Displacement tests were performed mostly in cylindrical Berea sandstone cores. In a few cases in which a much lower matrix permeability was desired, Blue Jacket sandstone cores were used. The vertical fractures were formed by cutting the cores with a thin circular blade or by parting them along a bedding plane. The vertical fracture plane always contained the axis of the cylindrical core. The subvertical fractures, cut with a saw, were inclined 45&apos; from the horizontal. The line of intersection between the planes of the vertical and subvertical fractures was parallel to the circular faces of the cores in all cases except one, as depicted by VF3HF-2 in Fig. 1. Fracture geometry of the other cores is also given in Fig. 1. Tables 1 and 2 give the physical properties of the solid and fractured cores, respectively. The suffixes and prefixes shown for each core have been used throughout the paper so that the reader may discern the fracture geometry from the core numbers.

Jan 1, 1970

By S. Feuerstein

THE influence of environment on the mechanical properties of metals has been extensively studied and documented.&apos; Most investigations have dealt with an interaction between a particular environment and a specific metal surface and the concomitant change in bulk mechanical behavior. Typical contributing media are oxide and metal film:;, electrolytes, and other surface-active agents. In the last category fall controlled gaseous environs (i.e., pressure or vacuum). Most vacuum exposure experiments prior to 1963 were conducted at pressures s>10-6 torr and elevated temperatures, or in such a manner as to prolong the exposure (e.g., by stress-rupture, creep, and fatigue). Little attention has been given to vacuum environment effects on the mechanical behavior of metals subjected to simple uniaxial deformation at room temperature. Test times and temperatures were assumed too ineffective as far as bulk changes were concerned. Further, the contribution of surface effects to the bulk mechanical behavior of metals was considered minimal. Under vacuums of the order of 1.0- 8torr and higher, molecular densities and, consequently, the rate of monolayer formation are such that exposures from seconds to days would be required for complete gas coverage. Thus, atomically clean surfaces created under ultra-high vacuum could conceivably maintain their cleanliness for time intervals orders of magnitude greater than at higher pressures. The influence of this unusual type of environmental surface phenomenon on the short-term bulk mechanical behavior of aluminum was first observed by Krame and Podlaseck in 1963.&apos; kin equivalent effect was reported for magnesium by Williams and Nelson.3 It was concluded from these studies2,3 that vacuum and, consequently, the monolayer formation rate of the oxide, were responsible for the described changes in flow behavior. The presence of an oxide layer impedes dis- I) EXPERIMENTAL DATA: MOLYBDENUM The tensile behavior of molybdenum was investigated by the author4-6 at ambient temperature over a range of pressures from 760 to 10-10 torr. These studies revealed that the flow behavior of the bulk specimens (0.200 in. diam by 2 in. gage length) was independent of pressure on sintered (0.062 mm grain size) and arc-cast polycrystals (0.012 to 0.149 mm grain sizes) and single crystals. Since the specimens were relatively large in size, it was assumed that any flow behavior effect would be surface-limited because of the short-term deformation procedure. Strain-rate-change experiments performed to determine the activation volumes for individual specimens at 760 to 10- 10 torr further indicated that the surface flow contribution was either minimal or zero, contrary to the findings of Shen el a1.7 on aluminum. Although the flow behaviors did not change, specimen ductility did change. For the sintered material at a strain rate of 4.2 x 10-4, specimen ductility was -9 pct higher at l0- 10 torr than at atmospheric pressure (dry nitrogen). A more comprehensive investigations on this same material revealed a distinct pressure dependence, Fig. 1. Intermediate and atmospheric pressure tests were obtained by backfilling the system from l0- 10 torr with extra dry, prepurified nitrogen. Other environments (air and purified argon) were also utilized for the 760 torr experiments; the results were essentially the same as those for dry nitrogen atmospheres. Departure from the fracture strain values obtained at 760 torr takes place in the vicinity of l0-6 torr, as indicated by the scatter band; a noticeable ductility increase is apparent at l0-8 and 10-10 torr.

Jan 1, 1970