Search Documents

By James Norman

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodu-mene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manga-nese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li2O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, ? the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3 The methods described in the second publication' did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted.

Jan 1, 1940

By L. L. Davis

The rapid increase in the use of pulvcrulent adsorptive materials in the so-called "contact filtration" process for decolorizing lubricating oils makes it desirable to consider some of the basic principles involved. The commercial methods and types of equipment now used arc fairly well known, having been extensively described in the trade journals. In spite of this very little has been published concerning the factors which must be considered in the selection of a process or of a decolorizing ing material. It is commonly understood that contact filtration more or less closely follows the laws of adsorption. These principles have been thoroughly drscribed by Gurwitsch.' The contacting of neutral mineral oils seems to be adsorptive in character and apparently follows Freundlich's law of adsorption which may be expressed by the formula: X = Color material adsorbed hy the clay. M = Amount of clay used. C = Concentration of color material after equilibrium. A and P = Constants for a given oil and clay. Fig. 1 shows the decolorization curve for a natural, dark colored cylin-der stock when contacted with various quantities of clay, curve R being made with natural Riverside Texas fuller's earth and T being made with an acid-treated clay from Texas. As the Tag-Robinson color is inversely proportional to the depth of color, the reciprocal of these colors ran be assumed to be a funct ion of the concentratlion of coloring matter. The values of and C' can, therefore., br calculated by using the reciprocal Tag-Robinson colors, and when these

Jan 1, 1928

By William Fink

ALTHOUGH age-hardening in an aluminum-base alloy containing magnesium was observed by Alfred Wilm1 as early as 1911, it was not until 1919 that a theory of the mechanism of age-hardening was proposed. Merica, Waltenberg and Scott,2 studying the age-hardening character-istics of Duralumin at the National Bureau of Standards, came to the conclusion that age-hardening of this alloy is caused by the precipitation of CuAl2, which is less soluble at the aging temperature than at the solu¬tion heat-treating temperature. It was postulated that the initially precipitated particles were of fine colloidal dimensions but that they gradually grew in size. Maximum hardness was assumed to be attained when the particles reached a critical size. This theory was at first received skeptically, since it was a widely accepted view at that time that the solid solution state should represent the hardest state of an alloy. Shortly thereafter, Jeffries and Archer proposed their well-known "slip interference theory."3 They suggested that age-hardening was accomplished by the precipitated particles acting as keys interfering with slip along crystallographic glide planes. They showed that this mechanical theory led directly to the assumption that maximum harden-ing would be produced by particles of a critical size, which they suggested would have a diameter approximately 10 times that of the aluminum atom. This contribution amplified and explained so rationally the age-hardening theory of Merica, Waltenberg and Scott that wide accept-ance resulted.

Jan 1, 1939

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

By Robert Baschwitz, John Chipman

The distribution of silicon between liquid silver and Fe-Si-C alloys has been studied at 1420oand 1530°C. The data are consistent with earlier studies. New data of Hager on the liquidus lines of the system Ag-Si and the distribution data are used to obtain the activity coefficient of silicon in both liquid phases. Data on the heat of mixing in iron permit accurate extension to 1600°C. Equilibrium data involving SiO2 and silicon in liquid iron together with revised data on the free energy of SiO2 are used to fix the activity of silicon in the infinitely dilute solution. The binary system exhibits strong negative deviation from ideality. At infinite dilution ? Si at 1600" is 1.25 x 10'3, and at concentrations up to NSi = 0.4 the slope d InySi/dNSi has a constant value of r; = 13. It is found that logysi in the ternary solutzon is approximately but not exactly the same function of Nsi + NC as of NSi in the binary. The results are consistent with currently available data on the free energy of Sic and its solubility in molten iron. LIQUID solutions of the system Fe-Si-C have acquired considerable importance as the laboratory prototypes of blast furnace hot metal. Equilibrium studies involving such solutions and slags approximating those of the blast furnace have yielded useful information concerning the thermodynamic properties of blast furnace slags. In studies of this kind great importance attaches to a knowledge of the thermodynamic activity of silicon in the solution as a function of temperature and composition. An attempt was made by Chipman, Fulton, Gokcen, and askey' to evaluate all of the pertinent data on this system and to deduce the desired relation between activity, composition, and temperature. These authors published data on the solubility of graphite and Sic in molten Fe-C-Si solutions and on the distribution of silicon between liquid iron and liquid silver. They showed further how the activity of silicon in very dilute solutions in liquid iron could be calculated from equilibrium data involving the molten alloy and solid SiO,. These calculations rested on the published thermodynamic properties of SiO, in- cluding its heat of formation which at that time was recorded as -209.8 kcal. This value has been under suspicion for some time and has recently been replaced by the concordant results from two independent laboratories2,3 which place the heat of formation of a-quartz at -217.6 kcal. This revision necessitates a re-evaluation not only of the activity of SiO2 in slag but also of silicon in molten iron. It is the purpose of this paper, therefore, to recalculate the activity of silicon, and in furtherance of this objective to present new data on its distribution between liquid Fe-Si-C alloys and liquid silver. HEAT OF SOLUTION OF SILICON IN IRON In order to determine the effect of temperature upon the activity coefficient it is necessary to know the heat of solution of silicon in iron as a function of composition. This is found in the data of Korber and Oelsen4 shown in Fig. 1. The curve corresponds to the following equation, which is of a form suggested by Wagner:5 Here AH is the heat absorbed in kilocalories in forming one gram atom of molten alloy from its molten elements and the N's are atom fractions. The relative partial molal enthalpies of the components, each referred to its pureliquid state and defined as zFe = aFe - PFe and zsi = HSi — -psi, are shown graphically. At low concentrations zSi = -28.5 kcal, in agreement with Kijrber and Oelsen's computation. This is in good agreement with the value of -29.3 kcal obtained by Chipman and Grant6 using an entirely different method. ACTIVITY AT INFINITE DILUTION From the known free energy of SiO, it is possible to obtain the activity of silicon in dilute solution in liquid iron from equilibrium studies. The heat of formation of a-quartz is —217.6 kcal and the heat capacity and entropy data are given by Kelley and ~ing.' The free energy of formation of ß-cristo-balite at temperatures above the melting point of silicon is expressed by the following equation: Si(Z) + O2(g) = SiO2 (crist); AF" =-226,500 + 47.50T [I] The value of the deoxidation product for silicon [%Si] x [%O]2 at 1600°C according to Gokcen and chipmans is 2.8 x 10"5, in agreement with results of Hilty and Crafts.9 More recent works of Matoba,

Jan 1, 1963

By J. F. Martin, L. M. Melnick, R. Rapp, R. C. Takacs

Recent studies on the determination of hydrogen in steel have shown that the hot-extraction method for removing hydrogen from a solid sample is preferable to its removal from a molten sample by vacuum fusion or by fusion in vacuum with tin. A number of techniques are available, however, for determining the hydrogen so extracted. They include: thermal conductivity, gas chromatography, pressure measurement before and after catalytic oxidation of the hydrogen to water and removal of the water, and pressure measurement before and after diffusion of the hydrogen through a palladium membrane. These techniques have been evaluated on the basis of initial cost, maintenance, speed and accuracy of analysis, and applicable concentration range. The results of this study showed that the palladium-membrane technique is best suited for routine use. FOR some time investigators have been concerned with the origin, form, and effect of hydrogen in steel. In such stdies', the analysis for hydrogen constitutes one of the most important phases. It is quite apparent that the results for hydrogen concentrations in a given steel are dependent on the method of obtaining the sample, storage of the sample until analysis, preparation of the sample, and analysis of the sample, including all the facets inherent in the calibration and operation of an apparatus for gas analysis. There are a number of means available for determining hydrogen. This is a critical study of some of the more common techniques in use today. In most conventional melting and casting methods, hydrogen concentrations of 4 to 6 parts per million (ppm) in steel are quite common. Because of the undesirable effects of hydrogen on steel there has been increased use of techniques such as vacuum melting,' vacuum casting, and ladle-to-ladle stream degassing, which lower the hydrogen content to levels on the order of 1 to 2 ppm. Therefore, the method used for determining hydrogen in steel must be sensitive and precise. In any analytical procedure for gases in metals there are two distinct operations—the extraction of the gas from the metal and the analysis of the extracted gas. To extract the gas from the steel, three methods have been employed: 1) fusion of the sample with graphite at high temperature; 2) fusion with a flux, such as tin, at a lower temperature; and 3) extraction of the hydrogen from the solid sample at a temperature below the melting point of the steel. Fusion with graphite is the least-acceptable method. The blank in this method is higher and more variable than in either of the other two methods. The hydrogen fraction of the total gas composition usually is between 10 and 50 pct; thus, a larger analytical error is possible. The vacuum-tin fusion4 extraction of hydrogen is probably the most rapid method in use today; the extraction time is usually about 10 min. However, with this system a bake-out of the freshly charged tin for 2 hr is necessary and a change of crucible and a charge of fresh tin are required after each day of operation whether one or thirty samples have been analyzed. In addition, frequent checks of blank rates are required since CO and Na are continually being given up by the steel samples dissolved in the tin bath. The composition of the gas in this method lends itself readily to analysis; although the hydroge concentration may fall to as low as 50 pct, more often it is above 90 pct, thus allowing a more precise analysis (because of less interference from other gases). In 1940 ewell' published the hot-extraction method for extracting hydrogen from the solid sample, comparing analysis for hydrogen extracted at 600°C with similar analysis for the gas extracted at 1700°C by fusion with graphite. Good agreement for hydrogen was obtained between these two methods, provided sufficient time was allowed for extraction at the lower temperature. carsone obtained good results in his comparison of this hot-extraction method with vacuum-tin fusion. Subsequent work by Geller and sun7 and Hill and ohnson' has shown that steel samples should be heated to at least 800°C to effect the release not only of the diffusible hydrogen but also of the "residual" hydrogen that may be present as methane. Since the rate of evolution of hydrogene9l0 depends on such factors as sample size and composition, thermal history, and extent of cold work, a fixed extraction time is not possible. Extraction times of 30 min are normal, but 2 hr are not unusual. Induction or resistance heating may be used in the hot-extraction method. With resistance heating the

Jan 1, 1964

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

By Thomas Cox

This paper makes no claim to any new idea; it simply reviews the Treasury Department Regulations pertaining to the practical application of depreciation and depletion and other allowances governing taxation of oil and gas properties. Other methods may be existent, but as they may not conform to the legal status they must be discarded. In complying with the present laws governing the industry with regard to taxation and the allowable deductions therefrom, the following considerations are essential: Depletion, depreciation, amortization, other allowances, and items not, deductible. It is definitely understood that depletion is the loss or exhaustion sustained in the continuous operating of an oil and gas property, and that each unit of oil or gas taken out reduces the value of the property until its final exhaustion. Depletion applies only to the natural deposits of oil and gas due to their removal in the course of exploitation of any property. Depreciation is defined to cover the waste of assets due to exhaustion, wear and tear, and obsolescence of the physical property, and is separate and distinct from depletion; its allowance is that amount which should be set aside for the taxable year in such sums as for the useful life of the property will suffice to repay its original cost—or its value as of Mar. 1, 1913, if acquired by the taxpayer before that date—less the salvage value at the end of such useful life. Amortization is allowed for such facilities as were built or acquired on or after Apr. 6, 1917, for the production of articles contributing to the prosecution of the war and, in the case of vessels, those built and acquired after that date. The amount to be extinguished, in general, is the excess of the unextinguished or unrecovered cost of the property over its maximum value under stable post-war conditions. Claims for amortization must be unmistakably differentiated in the returns from all other claims of depreciation. The taxpayer is also required to furnish full information with the claims for amortization to the full satisfaction of the Commissioner. Further reference is directed to the specific rules and regulations for making these claims.

Jan 1, 1921

By O. W. Ellis

In view of the extensive use of the brasses and bronzes in engineering practice it is indeed surprising that so little scientific work has been done on the oxides in these alloys. Recognition of the ill effects of these compounds is universally accorded, both in foundry procedure and in such specifications as cover the melting of these useful mixtures. In the latter, limits, for example, are placed on the proportions of scrap metal In the charge, and clauses governing the use of fluxes are included, the addition of fluxes to the charge being made with the object of avoiding oxidation during the process of melting and of subducing and separating non-metal-lic matter from the melt.1 In the manufacture of brass it occasionally, though rarely, occurs that the virgin metals, copper and zinc, alone arc used. In the event of virgin metals being employed, that of the higher melting point is always melted first. If it is melted under suitable conditions, little or no oxidation will occur. Whether oxidation has occurred or not, however, can best be determined by microscopic examination of a sample taken from the melt. Avoidance of Oxidation in Furnace Practice When melting virgin copper in crucible practice, the avoidance of oxidation is not difficult, nor is it hard to forestall trouble in the electric furnace. In gas-fired furnaces of the barrel type, however, the avoidance of oxidation is almost impossible, no matter what the condition of the flame, the flux employed, or the amount of charcoal included in the charge. Copper melted in furnaces of this type is almost invariably so highly oxidized as to requirc very considerable additions of such deoxi-dizers as, for example, silicon copper to render it free from cuprous oxide. As a result,, the castings produced are decidedly inferior, on account of the. large amount of silica which is engendered in the metal as a result of the reaction, Cu2O + Si = SiO2 + 2Cu. The deoxidation of such oxidized copper could, of course, be effected by means of zinc with, however, even more disastrous results.

Jan 1, 1930

By Howard Pyle

CORE analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.1 For convenience the subunit millidarcy, or one-thou-sandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil,4-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By Wallace Ralston

The East Texas area includes the northeast 38 counties of the state of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It is one of the most important oil and gas-producing areas of the Mid-Continent Province. It includes four important oil fields—Van, East Texas, Cayuga and Long Lake— and the recent extension of Rodessa field into Cass County, Texas, may prove to be of major size. Four commercial gas fields are in this area— Bethany, Waskom, Cayuga and Long Lake. Up to January, 1936, all of the oil has been produced from the Upper Cretaceous formations, and most of that from the basal member, the Woodbine sand. Gas is produced from both the Upper and Lower Cretaceous formations. Development in Fields East Texas Field.—This field continued to dominate the drilling and production situation throughout the United States. There were 4036 wells completed in this field during 1935; that is, 365 more wells than were completed during 1934. Drilling activity was due to close spacing of wells and the addition of 10,000 acres to the field. The field is now drilled to a density of one well to 6½ acres, which is certainly more wells than necessary for economic production of the field. The close spacing of wells is due mostly to the type of proration, which is per well allowable based on a potential test, and does not take acreage into consideration, and also to the numerous small acreage tracts such as town lots and excess strips. The field now has 19,519 producing wells. The allowable production for the field during 1935 was 161,118,659 bbl.; estimated production, including illegal or "hot oil," was 174,200,150. The illegal production of oil gradually decreased throughout the year, until an estimated low was reached of 20,500 bbl. daily during the months of November and December. The price of oil remained at $1.00 per barrel throughout the year. As stated, about 10,000 acres were added to the field during the year, making a total of 128,000 productive acres. There is a possibility that

Jan 1, 1936

By C. G. Brehm

The anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal measures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof support and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches. The Lower, or Southern field, is made up of basins of great depth, some being 4000 ft. deep, and its measures are mostly on very steep pitches. In certain sections this Southern field is being mined at an elevation of 1300 ft. below sea level, on a pitch ranging from 50' to practically vertical, and because of the tremendous pressure and the inherent gas in the seams, outbursts of coal frequently occur at the face, locally known as "bumps." These outbursts are accompanied by a rumbling noise, after which gas is usually found. This condition makes mining a difficult and extremely hazardous undertaking, and unusual skill is required on the part of the miner to drive and maintain openings necessary to the production of coal. Miners working in such seams on the heavy pitch must carry face batteries (Fig. 1) to afford proper protection while working at the face, because of the outbursts and free running coal. To drive haulageways or gangways in this field it is

Jan 1, 1940

By C. G. Brehm

The anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal measures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof support and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches. The Lower, or Southern field, is made up of basins of great depth, some being 4000 ft. deep, and its measures are mostly on very steep pitches. In certain sections this Southern field is being mined at an elevation of 1300 ft. below sea level, on a pitch ranging from 50' to practically vertical, and because of the tremendous pressure and the inherent gas in the seams, outbursts of coal frequently occur at the face, locally known as "bumps." These outbursts are accompanied by a rumbling noise, after which gas is usually found. This condition makes mining a difficult and extremely hazardous undertaking, and unusual skill is required on the part of the miner to drive and maintain openings necessary to the production of coal. Miners working in such seams on the heavy pitch must carry face batteries (Fig. 1) to afford proper protection while working at the face, because of the outbursts and free running coal. To drive haulageways or gangways in this field it is

Jan 1, 1940

By R. O. Neal

There are two main sources of the water that floods productive oil or gas sands. The water may rise from the lower depths of the producing stratum, or it may come from beds above or below the oil-bearing formation. Usually the recovery of oil is decreased by water entering the oil sands, and most oil-field waters, especially those of deep wells, tend to foster the formation of an emulsion, which is expensive to treat. This paper deals with a method of distinguishing between waters that encroach upon oil-bearing beds from sources in the same stratum and waters that reach the oil sands from horizons above. In order to remedy effectually water difficulties in oil and gas wells, it is absolutely necessary to determine the source of the invading water. Sometimes evidence such as the structural relations between the strata penetrated by deighboring wells and those found in the well under investigation is not adequate; also, data from drill logs and well records, from mechanical tests made on the wells by plugs, testers, drilling tools, etc., and from tests by chemical indicators such as eosin and Venetian red, may be unsatisfactory, for such data may fail to locate the source of the infiltrating waters. As a resort in such cases, the application of chemical analyses, that is, the comparison of an analysis of the water in question with that of typical waters from the various water horizons in that particular district, has in certain instances proved of value. This method has been used to advantage in the Westside Coalinga field of California, where the source of water may be fairly definitely determined , from its composition. The chief conclusions concerning the chemistry of the oil-field waters in California by G. S. Rogers1 are: "Oil-field water is not necessarily salty, as is generally believed, and may not be even slightly salty to the taste. The degree of concentration of chloride in such water is governed primarily by local conditions and is not affected by the position of the water in relation to oil. Sulfate diminishes in amount as the

Jan 1, 1920

By W. A. Thomas

STEAM is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 lb., are used for power out of each ton produced.

Jan 9, 1921

By Richard Divine

IN the Parkes process of extracting precious metals from lead, zinc is added to the molten lead containing gold, silver, copper, and, some antimony. These metals, with the exception of antimony, form an alloy with the zinc by reason of their greater affinity for it than for the lead, and this alloy, being lighter than lead, rises to the top, carrying the precious metals with it, whence it can be removed by skimming. These skimmings are further treated for the separation of the zinc therefrom, and the recovery of the precious metals, the zinc being driven off by heat and again used for another operation. In addition to the zinc that combines with the silver, etc., a certain amount is necessary to saturate the lead, and it is therefore necessary to treat the desilverized lead to free it from this residual zinc. To do this it is heated again in a reverberatory furnace and air or steam is blown through it. This oxidizes the zinc together with a small amount of lead and antimony, leaving the lead free from zinc and antimony, and forming oxides of these metals, which rise to the. top and are skimmed off. This process relates to the separation of the metals in these oxides or skimmings. The skimmings are cooled, crushed, and mixed with carbonate of soda and pulverized oil coke. The mixture is heated in a reverberatory furnace on a bath of lead, to about 1,000°C. The metals are reduced by the coke, the lead and antimony go into the lead bath, while the zinc is volatilized and burned to oxide. This impure oxide is at the present time treated at Omaha by the Hall process of electrical precipitation, making a very pure metallic zinc. It can also be very easily refined by the old Schnabel process of using ammonia and carbon dioxide as a solvent. It seen-is to be in an ideal form for this purpose, and very few changes from the original method are required to obtain the zinc oxide practically C. P., leaving the lead and antimony as residues.

Jan 8, 1914

By Arthur Hixson

ALTHOUGH a few engineers have recognized the problem of the mechanism of filtration it has never been studied in a quantitative way. A background for a better understanding will be afforded by a survey of certain fundamental principles of filtration. In recent years, authorities have become practically unanimous in saying that the actual filtering should be done, not by the cloth itself, but by a layer of solid particles deposited upon it. Thus, a cloth may be used in which the openings are considerably larger than the particles to be filtered, provided that groups of particles form an arch or bridge over each opening. This can be accomplished if the initial pressure is so low that the arch will not be broken while it is still thin. According to Wright,1 the chief advantage of this method of filtration is that the open-weave cloth does not become clogged as easily as does one of closer weave, where the fine particles often work their way into the interior of the cloth and become caught there. If the character of the material to be filtered is such that it will not form a good film, then it becomes advantageous to use "filter aids" for pre-coating the cloth with a desirable layer of solids, and the coating need be only of a very slight thickness for good results. Until the film is formed, the first runnings of the filtrate may be cloudy, often necessitating refiltering this portion. A factor which has considerable effect on the performance of filters is the concentration of solids in the pulp. According to Wright, a. high concentration of solids gives a porous cake, since the flow is then slower than with- a thin pulp. The porosity of the cake is also affected by the pressure: a high initial pressure tends to compact the cake, and the same effect results from fluctuations of pressure. In his studies of the relation between pore size and particle size, Hatschek2 observed that the particles in a pulp tend to arrange themselves with maximum cross-section parallel to the direction of flow and that this is more marked at the higher velocities. Thus, at high pressure and high velocity, a certain pulp

Jan 2, 1926

By R. E. Ricksecker, W. M. Baldwin, R. McC. Baker

INTRODUCTION THE development of residual stress in strip during rolling has not been systematically studied. A few scattered papers1-3 mention the existence of residual stresses in rolled strip or touch upon some of their consequences,4 but there is no report of experimental studies in the literature describing the effect of roll diameter, strip thickness, reduction per pass, metal or metal temper on the magnitude of residual stresses developed in strip. A knowledge of the effect of these factors is of utmost importance since the present trend in some mills to roll thicker castings brings the rolling operation directly into that set of conditions which, as will be brought out in the present paper, can develop residual stresses of a high order of magnitude. Fundamentally, residual stresses are developed when a metal is inhomogeneously unloaded from a plastic stress state. A quantitative treatment of the problem requires a reasonably complete understanding of both the plastic stress state existing in the metal during deformation and the elastic stress state that would exist in the metal if the metal deformed as a perfectly elastic body. Our knowledge of either state during rolling is so meager that we can make no more than certain limited predictions. The external stress state* operating between the roll and the metal consists of compressive stresses acting almost perpendicularly to the strip surface but vary [ ] ing in intensity both across the width of the strip and along the length of contact between the roll and the strip. An example of such a stress distribution is shown in Fig I. The nature of the internal stress state, produced by this distribution, is not known. Various investigators,5-7 however, have felt that a qualitative similarity must exist between the internal stress state so produced and that produced in a wide strip that is compressed between two flat-nosed punches. In the latter case the external stress state is represented by a uniformly distributed compressive stress acting perpendicularly over the face of the tool. The elastic internal stress state in this case is complex-the principal stresses showing

Jan 1, 1948

By Benj. E. Shackelford

THE present paper is concerned with typical temperature values experienced in lamp-filament measurements as made on regular factory and engineering products. It deals with the relations existing between temperature, efficiency, lamp size, and life of incandescent lamps, insofar as they affect the rating of the product and its use by the individual consumer. The temperatures measured lie in that range covered only by the general method of radiation pyrometry, as opposed to direct methods used under contact conditions. The range of temperatures ordinarily experienced extends from about 2125° K., for the now almost extinct carbon-filament lamp, to 3200° K. for the comparatively new tungsten-filament motion-picture lamp. Most of the more common sizes of tungsten lamps have temperatures ranging from 2500 to 3000° K. Because of the high temperatures involved and the relatively small area of the sources used, we are practically restricted to two methods of measurement, both of which depend on the light radiated front the filament. The first and more usual method is that of the Morse pyrometer, dependent on the variation in temperature of the amount of light of a given color range yielded by the filament. In this case, the measured temperature is that of a small part of the incandescent body, that is, the part which is focused on the comparison filament. The second method, known usually in this country as that of "color match" and in England as "color-identity" is based on the color of the total light yielded by the filament, the comparison being facilitated by the use of an ordinary photometer- head. A more definite idea of the temperatures involved in the case of filaments of various vacuum and gas-filled lamps, is given by Fig. 1. The size of the lamp, in watts, is plotted along the horizontal axis and the temperature of the filament is plotted along the vertical axis. The lamps concerned are regular product, rated for 1000 hr. life. The temperature values for the old 16-candlepower carbon lamp and the new motion-picture lamp are shown by the cross and circle respectively.

Jan 9, 1919

By G. S. Hume

In Alberta, an oil well with an estimated capacity of 60 to 100 bbl. was "brought in" at Wainwright, the oil being derived from the Colorado group of rocks. In the Norman fields, Mackenzie River area, two new holes completed showed no oil in commercial quantities whereas the "Discovery" well has now an increased flow amounting to about 100 bbl. In Kent Co., Ontario, a well from low down in the Trenton formation gave an initial flow estimated at 200 bbl. This opens up new possibilities for the Ontario fields as this is the first oil from this depth in the Trenton. ACTIVE drilling operations for oil were carried on during the summer of 1923 in various parts of western Canada, particularly in Alberta. During the early part of the summer, interest centered in southern Alberta, in the Coutts area, just north of the producing Kevin-Sunburst field of Montana; but on Nov. 14 a strike of oil by British Petroleums Ltd. at its well near Wainwright, 120 mi. east of Edmonton, diverted public attention to a new field. According to present estimates, this well has a possible production of from 60 to 100 bbl. a day; the oil is 15° Bé. with an asphaltic base and is obtained from a sand at the depth of 2019-2036 ft. The oil stands at 1700 ft. in the casing and there is sufficient gas pressure to cause it to flow when the well is opened. The oil horizon is in a sandstone in rocks of Colorado age. It is known that there is a terrace structure of which the western edge extends in a northwesterly direction from the vicinity of Hardisty to Viking, where it probably swings more to the north. At Viking a small dome-like structure on this terrace gives rise to an important gas field. Wainwright lies directly northeast of Hardisty. The exact structure in the Wainwright field is unknown. At Fabyan, 6 mi. northwest of Wainwright, the Imperial Oil Co.1 last year brought in a large gas well estimated at 14,000,000 cu. ft.; the escaping gas sprayed a small amount of heavy black oil over the derrick. The gas was obtained at a depth of

Jan 2, 1924