Search Documents

By Darrel W. Hansen

Morrow Point Dam and Power Plant are principal features of the Bureau of Reclamation's Curecanti Unit of the Colorado River Storage Project. They are under construction on the Gunnison River 20 miles east of Montrose, Colo. Johnson-MK is the prime contractor, and represents a joint venture of Al Johnson Construction Co., Minneapolis, Minn., and Morrison-Knudsen Co., Inc., Boise, Idaho. The power plant will be housed in an underground chamber in the left abutment, approximately 250 ft behind the original canyon wall. The chamber is 206 ft long and 57 ft wide. The distance from the foundation to the spring line of the roof arch varies from 51 ft in the service bay to 120 ft in the control bay. The roof arch has a rise of 16 ft. The longitudinal center line of the chamber is orientated east-west with the draft tubes discharging nearly due north. Access to the power plant chamber was possible through the cable tunnel, access tunnel, two draft tube tunnels, two penstock tunnels, exploratory tunnel, which became the ventilation tunnel, or the grouting and drainage tunnel leading to the dam. (See Fig. 1.) The shortest and fastest access was through the cable and access tunnels, and the contractor drove these two tunnels simultaneously. The cable tunnel and cable gallery excavation exposed a transverse section, at the west end of the chamber, that was 15 ft wide and extended from the crown to 5 ft below spring line. It was here that arch excavation began. The first 34 ft of advance along the arch was driven on three headings, and the muck was removed through the cable tunnel. Meanwhile, the access tunnel was completed, and a raise was driven from its crown to intersect the advancing arch excavation near the longitudinal centerline

Jan 1, 1968

By J. E. Burke

THE origin of so-called annealing or recrystalli-zation twins in face-centered-cubic metals continues to be a matter for speculation, and in the present report an attempt is made to explain their origin and to account for at least a majority of the observations concerning their behavior. The fact that annealing twins are prominent only The speelmen was deformed 8 pet in compression and then indented over the lower left-hand corner in a Rockwell in-denter, and then annealed to cause partial recrystallization. Note intense twinning in heavily deformed part and slight twinning in less deformed part. The upper right-hand corner is unrecrystalized. Area reduced approximately 25 pot for reproduction. after recrystallization suggests that deformation may be necessary for their formation. In 1926, Mathewson1 reported the observation by Phillips that annealing twins are frequently parallel to strain markings which delineate octahedral planes in the deformed (and partially recrystallized) matrix, and suggested that strain markings are mechanical twins which grow into annealing twins during recrystallization. Later work by Burke and Barrett' has shown that strain markings are traces of planes upon which slip has occurred, and that there is no evidence for the formation of mechanical twins of microscopically resolvable width in face-centered-cubic metals. Mathewson3 has pointed out, however, that slip may produce twin faults, and later modifications of this hypothesis have assumed that twin faults rather than true mechanical twins serve as the nuclei for annealing twins. Carpenter and Tamura5 suggested, also in 1926, that annealing twins might form by accidents of growth. A close-packed layer of atoms can be added to the octahedral plane of a face-centered-cubic metal in two possible positions, the right position

Jan 1, 1951

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By J. E. Clennell

It is a common observation that the improvements introduced in practice since the first announcement of the cyanide process have been almost entirely mechanical. Although .a good deal of study land research has been devoted to the chemical problems [involved, the results obtained appear trifling in comparison. Few of the suggested modifications in the chemical treatment have come into practical use and those only in limited fields. Nevertheless, if we study the recent history of the cyanogen compounds from a somewhat broader standpoint, we shall find that considerable additions have been made, not only to our knowledge of their chemical properties, but also to their applications for industrial purposes. The present review of these advances naturally falls into two divisions: (1) processes involved in the treatment of ores; (2) manufacture of cyanides and other related compounds. Part I. Advances in the Chemistry of Ore Treatment by Cyanide In the attempt to extend the scope of the process, various ores have been encountered which contain gold and silver in such forms that they will not yield satisfactorily to ordinary methods of cyanide treatment. In some cases the difficulty is due to the excessive action on the solution of base metals present in the ore; in others, to the occurrence of minerals such as dyscrasite (the native alloy of antimony and silver), or a supposed oxidized manganese compound containing silver, which are either altogether insoluble in or very slightly attacked by cyanide. A particularly troublesome case is that of the so-called "graphitic" ores, containing carbon in some form which has the property of precipitating gold and silver already dissolved. Other efforts have been directed to improving extraction by electrolysis of working solutions, and by addition of various chemicals with or without electrolysis; to the diminution of cyanide consumption by "re-

Jan 1, 1916

By Ionel I. Gardescu

Natural gas influences the movement of oil through reservoir rock by affecting the physical properties of the oil and the pressure within the reservoir. The presence of gas bubbles changes the laws of flow and the distribution of forces. The problem of flow of oil and gas through a porous rock is complex, and most authors, in order to analyze their problems, have found it necessary to make or accept certain generalized assumptions. Some of these assumptions, particularly the ones dealing with capillary phenomena and moleculnr forces, have not received sufficient attention and by lack of understanding have often been misinterpreted. Herold1 has called attention to the resistance offered by gas bubbles in capillary spaces and has drawn some interesting conclusions with regard to the action of natural gas in a reservoir rock. He has duplicated an experiment of the French physicist Jamin, has interpreted his findings in terms of molar mechanics, and, from experimental observations, has made a number of assumptions which he later applies in discussing problems of natural flow and recovery of oil. The Jamin action is an assumption because it lacks a physical proof and has never been determined quantitatively. Tickel12 attempts to develop a formula expressing the work performed by a distorted bubble. H. A. Wilson, in the recent publication of the American Petroleum Institute on the function of natural gas, discusses the phenomenon in terms of classical physics. Both contributions are incomplete and offer no experimental data. This paper includes a study of the static condition of equilibrium of gas and liquid bubbles confined to capillary spaces. In order to avoid any possible confusion, it is proposed to restrict the term "Jamin action"

Jan 1, 1930

By Philip Wilson

Tun mines of the Calumet & Arizona Mining Co. are situated in the Warren Mining District, Cochise County, Arizona, between Bisbee and Warren and adjoin those of the Copper Queen Consolidated Mining Co. and the Shattuck Arizona Copper Co. Paleozoic limestones of considerable thickness have been intruded by granite porphyry. A great stock of the intrusive outcrops boldly near the city of Bisbee and is known as Sacramento Hill. From this central core the porphyry has tongued out into the limestone for many thousands of feet as dikes and sills of irregular shape and variable dimensions. Churn drilling has recently developed a large tonnage of secondarily enriched copper ore in the main porphyry mass of Sacramento Hill. While some ore has been found in porphyry in other parts of the district it is relatively unimportant compared with that which occurs in the Paleozoic limestone as irregular lenses replacing favorable beds near porphyry contacts or associated with well-marked fracture zones often many hundreds of feet away from the intrusive. In a zone extending from Sacramento Hill for a distance of from 1,500 to 3,000 ft. the limestone has been extensively metamorphosed and in this contact metamorphic zone the ore occurs through a known vertical thickness of upward of 900 ft. and individual orebodies often show extension in a vertical direction of over 200 ft. At a greater distance from the intrusive stock the ore occurs as lenses of greater horizontal than vertical dimensions with an average thickness of approximately 30 ft. An exception to this rule is found in the occasional steeply dipping mineralized fractures, almost true tabular veins, which are found long distances away from the zone of contact metamorphism.

Jan 7, 1916

By Werner Goldsmith

This discussion is confined to the first section of Professor Clark's paper entitled 'Elastic and Nonelastic Waves' and its application to wave propagation in rocks. Some published results by other investigators concerning measured decay of peak strain and variation of pulse duration with travel distance are cited, but the principal subject of this section is a detailed mathematical analysis of spherical (and, to a lesser extent, of plane) wave propagation in various homogeneous, isotropic media. The materials selected include an elastic substance, a Voigt and a 'modified' Voigt solid-the latter incorporating the assumption of a constant loss factor (defined here as the product of frequency and the ratio of the imaginary to the real part of the shear modulus)-and a solid friction model. While other possible representations of a solid continuum model are mentioned, corresponding solutions are not presented. The pulse inputs considered comprise exponential decay, a unit step, and steady- state sinusoidal excitation: the process of conversion from one solution to another in the operational plane is indicated. The basic problem relative to the analysis of wave propagation in rocks concerns the specification of the appropriate material behavior, since the equations of motion for a given geometry of the source and medium are well established. In principle, the required information can be deduced from two types of measurement: 1) field observations of underground explosions or seismic disturbances, and 2) laboratory tests on small samples of the pertinent rock. However, in practice both types of approaches are beset with difficulties and subject to valid criticism. Field observations must be carried out under relatively uncontrolled conditions, including, in general, a lack of knowledge of the precise arrangement of the medium, stratification, faulting. inhomogeneities, etc. Specimens investigated in the laboratory can not represent the environment found

Jan 1, 1967

By E. E. White

In August, 1911, I read a paper before the Lake Superior Mining Institute1 on surveying and sampling diamond-drill holes. The present paper gives a more thorough descriptiou of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling' and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drillholes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-hole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a

Jan 1, 1913

By Claus G. Goetzel

PRESSING of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal [ ] friction. As long as curved surfaces, recesses, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more difficult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB). Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. VARIABLE FACTORS IN MOLDING POWDERED METAL PARTS Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2 : I would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only I.5, a compression ratio of 5:I would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1945

By W. E. Bruce, R. J. Morrell, James Paone

This chapter is a partial summary of an investigation by the U.S. Bureau of Mines (USBM) made in response to a recent request by the Assistant Secretary, Water and Power Development of the U.S. Department of the Interior, for a comprehensive review of horizontal boring technology related to underground power-line installation. This review is concerned primarily with 3 to 36-in. diam horizontal holes from several hundred to several thousand feet in length. An electric power system consists of three essential functions: generation, transmission, and distribution. The generation component includes the generating station and step-up substation; the transmission component includes the transmission line and stepdown substation at typical voltage levels ranging from 69 to 345 kv for underground lines and 69 to 500 kv for overhead transmission lines; the distribution component includes the distribution line carrying the commonly used voltages of 120, 208, and 240 v, the distribution transformer, and the line to the service customer.l The Federal Power Commission reports that 1600 miles of underground transmission lines of 60 to 345-kv capacity are now in service in the United States. By 1980, it is estimated that approximately 3000 miles of trans- mission lines will have to be placed underground.2 The cost of burying electric transmission lines underground in metropolitan areas, approximately 30 miles from the center of each of the most populated cities, will exceed $1.5 billion with the methods now available. The wide spread in unit costs of overhead and underground transmission lines narrows as right-of-way costs for overhead transmission in congested areas increase. Improved methods of underground emplacement will certainly reduce this difference in costs and even further favor underground emplacement. Also, in the future, overhead transmission lines will probably not be permitted in highly built-up areas.

Jan 1, 1970

By Oswald J. Heinrich

SINCE my communication to the Institute at the Baltimore meeting in 1879,* in which I took the lead in emphasizing the importance of a new method in the manufacture of soda, already practiced to some extent in England and on the Continent of Europe, five years have passed. I.then referred particularly to the advantages offered in the United States for this peculiar method, by the ammonia process, namely: 1. At the present time, at least, we have but one mine in this country where rock-salt is mined, namely, at New Iberia, La. On the other hand, we have many localities where brine of various degrees of strength, up to that of cold saturation, is obtained in large quantities. 2. We have excellent fuel, in close proximity to most of the brinecenters. 3. Our supplies of pyrites, to use in the manufacture of sulphuric acid, for use in the manufacture of soda by the Leblanc process, are mostly too far from the brine-centers to permit competition in that line with the more favorable conditions existing in England. 4. Unlike our foreign rivals, we have no large and costly plants, erected on the Leblanc plan, which must be abandoned and exchanged for new but cheaper plants, before the ammonia-soda process can be adopted. 5. We have a constantly increasing demand for soda, which is almost entirely supplied by importation. If slow progress has been made hitherto in this country in the extension of this manufacture (only one plant at Syracuse, erected . under the Solvay patent, having as yet been placed in operation), I still feel gratified in saying that developments in England, and particularly on the Continent of Europe, give ample proof of the

Jan 1, 1885

By Wm. Hamilton Merritt

With the exception of the Vancouver Island coal, all the western coal-fields owe their present development to the completion, in the autumn of 1886, of the Canadian Pacific railroad. While it could not be expected that a very great deal could be accomplished in three years, enough has been done to pretty thoroughly establish the coal-bearing areas and their correspondence with those which have been developed to the south of the boundary along the lines of the transatlantic railroads in the United States. This summer I visited some of the important developments in the coal areas of Washington Territory, largely with the object of being better able to appreciate the corresponding coal-bearing areas in British Columbia to the north. In Western Canada, coal-bearing rocks have been found in three zones: 1. In the plains to the east of the Rocky Mountains and in the eastern flanking ranges, the coal occurs in the Cretaceous formation (including the Laramie). 2. In the interior plateau of British Columbia, the coal is found in the Tertiary formation. 3. On the coast of British Columbia, Cretaceous and Tertiary rocks are found carrying coal, and on the Island of Vancouver the well known Nanaimo coal has been worked for years in the first named formation. In all of these zones, the coals vary from lignites up to higher grades, the factor determining quality being the amount of pressute to which they have been subjected. The intensity of this pressure is generally shown by the disturbance which the coals exhibit, and, in many cases, is almost directly in proportion to the distance of the deposits from mountain ranges. This seems to be also the opinion expressed by Mr. Bailey Willis in connection with his Census Report on the coals of Washington. It has been elsewhere stated

Jan 1, 1890

By Dorsey Hager, G. W. McPherson

The rapid increase of water troubles in the Mid-Continent oil fields is causing much alarm. Troubles occur at Towanda, Eldorado, Augusta, Cushing, Blackwell, and Healdton, although they had not been acute in the Mid-Continent field until about two years ago, when the unusual conditions in the deeper oil fields were first encountered. California faced the same situation, but, thanks to aggressive measures, has largely overcome the dangers. The following analysis of water trouble may throw some light on the subject and be of assistance in solving the problems involved. Water Troutles Classified The presence of water in large quantities in oil sands has the following results: 1. Diminishes oil production. 2. Diminishes casing-head gasoline production: (a) By curtailing the gas flow. (b) By making the use of vacuum pumps unsuccessful. 3. Increases lifting costs: (a) By making it necessary to pump large quantities of water, which requires a fast motion and long stroke (third hole). (b) By requiring the use of compressors for air lift. (c) By causing break-downs and delays due to the high speed necessary to pump water. (d) By making it necessary to treat "cut" or emulsified oil. Oil production is seriously curtailed by the presence of large quantities of water. Lease records show that wells are shut down 40 to 60 per cent, of the pumping time where serious water trouble occurs. While a small quantity of salt water may cut the paraffine and keep the oil moving, several hundred feet, or a hole full of water, effectually "kills" the oil and gas. The quick return of wells to production, once the water is shut off, shows how wells have been affected. The killing of gas sands

Jan 1, 1920

By J. E. Gosline

IN any theory of a hydrodynamic nature dealing with the vertical flow of gas-liquid mixtures in pipes, the two factors that present the greatest difficulty are the relative motion between the phases and the energy loss resulting from turbulence work. The former has generally been referred to in the literature as "slippage" and the latter as "fric-tion." A third factor of importance is the nature of admixture between liquid and gas for both the relative motion between the phases as well as the turbulence work are functions of the type of mixture. Although much work of a general nature has been performed on the vertical flow problem, there have been very few attempts made to study experimentally the factors involved in the phenomenon individually. Of these, perhaps the most notable is the work of Moore and Wilde1 on slippage. Some writers on the subject have assumed that over a wide range of operating conditions the controlling type of mixture, is one in which gas bubbles of uniform size are distributed throughout the liquid, and that the data obtained from experiments on the motion of single bubbles through various liquids may be used in evaluating the slippage. Ver-sluys2 has further assumed another controlling type of mixture in which the liquid occurs as a dispersed phase within the gas and applies data on the fall of drops of water in air to calculating the relative velocity. It was for the purpose of studying the applicability of data on single bubble motion to the slippage factor and to further observe the nature of mixtures that a research program was conducted at the University of California during 1932 and 1933. These experiments formed a basis for

Jan 1, 1935

By E. Posnjak

IT is rather the general belief that acidified solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no. oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by, passing air for 3 hr. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will be proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2. His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 1, 1927

By Orson Shepard

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thick-ening and filtration was developed, and is extensively used to the pres-ent day. Even though the agitation-leaching slime process is considered satis-factory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of j work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking clown the glomerules. The agglomeration trickle-leaching method was devel-oped on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long is the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solu-tion flooded the charge, the glomerules broke down and, the charge became impervious. There are two important difficulties in the application of the agglom-eration trickle-leaching-method to the cyanide process for gold and silver ores:

Jan 1, 1937

By Darwin Soler

This chapter will outline the operating procedures at Freeport Kaolin Co.5 kaolin mining operations in Georgia, with emphasis on explaining new techniques recently introduced to reclaim mined-out areas for reforestation. Kaolin is found in the central Georgia area (See Fig. 1) in lenticular, sedimentary deposits of high purity. The beds are Cretaceous in age and vary from 4 to 60 ft in thickness, under a cover of sedimentary overburden ranging from 5 to 150 ft. The kaolin beds contain the mineral kaolinite (a hydrous aluminum silicate) and have a particle-size distribution ranging from about 20µ to the submicron level and averaging about 60% below 2µ. The only contaminants in the deposits are coarse mica, quartz particles, and minor amounts of iron and titanium oxides. These kaolin deposits vary widely in quality from deposit to deposit and also vary within individual deposits. Some of the controlling quality specifications which are determined during exploration are viscosity in water suspension, optical brightness index as measured by reflectance, amenability to bleaching, and particle-size distribution. For this reason, only a small portion of the total kaolin reserves in the Georgia belt are suitable for wet processing for the present markets being served. Kaolin clays are selectively mined by different mechanical methods and are beneficiated by both wet and dry processing to produce a number of products used as fillers and coatings in the paper industry; fillers or additives in the paint, plastic, and rubber industries; and as basic raw materials for the ceramic industry. The State of Georgia is the largest kaolin producer in the United States, with 3,206,454 tons produced in 1966, according to U.S. Bureau of Mines statistics. Freeport Kaolin Co’s processing plant is located in Gordon, Ga., about 20 miles east of Macon, Ga.

Jan 1, 1969

By William L. Fink, Kent R. Van Horn

Aluminum forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.² Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560" C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550" or 560' C.; in fact, some of the specimens were the identical ones used by nix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1931

By Alden B. Greninger

Twinned metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the observation of the twins, there are two other possible groups: (1) solidification twins,† when observed in the as-solidified or as-cast condition, and (2) transformation twins,† when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form (112). Since McKeehan's discovery, little or no attention has been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the preparation of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures—at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neil13 has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually contailled a few annealing twins. Tamura4 as reported "twin-like" crystals both in wrought iron and mild steel; specimens of the latter were annealed above and below A3 and showed "twin-like" crystals after both kinds of treatments.

Jan 1, 1936

By Alden B. Greninger

Twinned metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the observation of the twins, there are two other possible groups: (1) solidification twins,† when observed in the as-solidified or as-cast condition, and (2) transformation twins,† when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form (112). Since McKeehan's discovery, little or no attention has been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the preparation of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures—at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neil13 has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually contailled a few annealing twins. Tamura4 as reported "twin-like" crystals both in wrought iron and mild steel; specimens of the latter were annealed above and below A3 and showed "twin-like" crystals after both kinds of treatments.

Jan 1, 1936