Search Documents

By T. A. Read, M. W. Burkart

The crystal geometry of the cubic-tetragonal interface after partial transformation of an indium-thallium alloy single crystal is described and a general theory is presented. The effects of applied stresses on this transformation are interpreted and the latent heat of transformation is obtained from observations of transformation under stress. A DIFFUSIONLESS phase transformation between face-centered cubic and face-centered tetragonal structures has been reported for the indium-thallium system by Bowles, Barrett, and Guttman1, 2 The transformation takes place at approximately 105 "C at 18 atomic pct Tl and 25°C at 23 pct Tl. In their study, Bowles, Barrett, and Guttman used poly-crystalline samples whereas in the present study single crystals were used to eliminate the transformation constraints imposed by adjoining grains. The use of single crystals made possible a comprehensive study of the effect of stress on the transformation. In the course of the work, it was possible to formulate a new method of analyzing dif-fusionless transformations (presented in this paper) which permits calculation of the geometry of the interphase interface from a knowledge of the crystal structures of the initial and final phases. The specimens were prepared from chemically pure thallium and 99.97 pct In which were weighed out to produce 3 to 4 grams of alloy of the desired concentration. The metal was placed in clean fused silica tubing, then melted, degassed and sealed under vacuum. (To obtain single crystals, it was found that both degassing and extreme cleanliness were essential.) Single-crystal specimens were grown by a modified Bridgman technique.8 pecimens were removed from the tube by dissolving the quartz in concentrated hydrofluoric acid which attacks the specimen very slowly. The specimen then was polished mechanically to produce four flat surfaces, electropolished, and annealed at 140°C for 48 hr. The electropolishing solution used was that described by Bowles, Barrett, and Guttman and the polishing was carried out on both the high and low temperature phases of the alloy. The high temperature polishing was done at 110°C with a stainless steel cathode. Visual Observation of the Transformation in Single Crystals A visual study of the transformation was made on specimens which had been electropolished in the high temperature phase. The specimens were supported on the stage of a metallograph by an electrically heated holder which contained an opening for observing the specimen. Visual evidence of transformation was found in the presence of an interface which separated the two phases. The interface plane defines the boundary of the phase undergoing transformation and manifests itself by the sharp change in angle between the surface of the specimen and the incident light at the juncture of the two phases. On slow cooling, well-annealed specimens transformed from the face-centered cubic structure to the face-centered tetragonal structure by the motion of a single plane interface which traversed the specimen from one end to the other. Upon heating, the interface moved back in the reverse direction. The interface could be started, stopped, or reversed at will. A temperature hysteresis of about 31/2oC was observed in the reversal of the interface. Holding an interface stationary caused it to disappear completely in most cases, whereas in other instances the interface became less distinct depending upon its orientation. The interface could be made to reappear by changing the temperature of the specimen. The low temperature tetragonal structure exhibits only the fine markings or subbands reported by Bowles, Barrett, and Guttman and is illustrated in Fig. 1. These subbands are twin-related. Back-reflection Laue patterns show the breakup of the cubic spots into pairs of spots corresponding to the twin orientations of the tetragonal phase.

Jan 1, 1954

By L. D. Jaffe

From data found in the literature, a method has been derived for calculating hardenability of titanium alloys from their composition. A single graph gives the contributions of each alloying element. These are simply added to a base hardenability for unalloyed titanium. Results agree satisfactorily with measured harden-abilities. RECENTLY the importance of hardenability of titanium alloys in permitting attainment of high strength and hardness has become apparent. If a titanium-base alloy has adequate hardenability for the section size and quenching practice used, it can generally be heat treated to high strength and hardness either by simple quenching or cooling from temperatures near the ß transus, by quenching and tempering (aging), or perhaps by direct isothermal transformation of ß1,2 If the hardenability is inadequate, high strength cannot be attained. Preliminary charts translating hardenability requirements for shapes quenched in various media into terms of Jominy end quenched hardenability specimens or ideal round sizes are now available for titanium alloys." The method proposed in 1942 by M. A. Grossmann for calculating hardenability of steels from composition has proved to be of great practical value.' It appeared worthwhile to see whether, using information available in the literature, a corresponding method for calculating hardenability of titanium-base alloys could be derived. Data No systematic experimental study of the hardenability of titanium-base alloys has yet been made. There is available, however, a considerable quantity of scattered data bearing on hardenability. Some investigators determined Jominy curves on one or several alloys. Others reported as-quenched hardness for specimens of a few alloys cooled at various rates or in various media. Still others gave the as-quenched hardness for systematically varied composition, using one or several cooling mediums. The measurements utilized in this work were limited to hardness. Strength measurements were not used because a low strength may reflect high hardness combined with brittleness. Since, in general, the hardness of titanium alloys goes through a peak as the cooling rate is varied from extremely fast to extremely slow, the cooling conditions at which peak hardness was found were taken as the measure of hardenability.1,2 When as-quenched hardness was found to drop as the content of an alloying element (believed to increase hardenability) was raised, this was taken as an indication that the cooling rate was faster than that giving peak hardness; otherwise, the hardness should go up because of solid solution hardening. Also, if the hardness increased on tempering at low temperatures, this was again taken to indicate that the cooling rate had been faster than that giving peak hardness. Many of the data did not indicate precisely the cooling conditions for peak hardness but merely set a maximum or a minimum bound, or a bracket. Since the sizes of specimens quenched and the location of the hardness readings were not always given, it was occasionally necessary to estimate reasonable limits for them. Only the nominal compositions were available in some cases. As quenching from below the ß transus is equivalent to starting with a mixture of a and ß phases, whose individual composition would differ from the overall composition of the alloy, only measurements after quenches from above the ß transus were used. Hardness measurements on samples heated during metal-lographic mounting were also discarded. Because of their bulk, the data used will not be reproduced. They have been or will be published elsewhere.5-22 Approach All data were first translated into terms of ideal round size. For conversion from Jominy or quenched round or sheet, the author's graphs were used." For a few furnace cools or helium quenches where cooling rates were given, conversion was made on the basis of equal cooling coefficient.23 Plots of ideal round size for peak hardness against percentage of alloying element were next made for

Jan 1, 1956

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.' The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By Frederick Laist

THE past year has witnessed no radical changes in methods for the reduction and refining of copper. The Carson litigation was finally brought to a close ant1 the copper smelter is again free to introduce charge into his reverberatory furnaces in whatever manner suits him best. This litigation naturally led to much experimentation with various methods of charging and with various types of bath. In some cases the charge was introduced more or less centrally on a relatively dry hearth and in other cases into a bath of greater or less depth. The results of these furnaces were meticulously compared with the results obtained in side-charger furnaces, and it was apparent that it made little, if any difference how a given furnace \\.as charged so long as care was taken that there was always something in the furnace for the flames to work on. So long as this requirement was complied with, consumption of fuel per ton of charge smelted and tonnage smelted per furnace day remained substantially the same regardless of the method of charging or the depth of bath employed. In some instances the center-charged deep-bath furnaces gave slightly better results than the side-charged particularly with respect to copper losses. The slags of the deep-bath furnaces are generally a little cleaner

Jan 1, 1930

By George Stern

THE purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- [ ] sists of pressing and subsequently sintering an intimate mixture of iron powder and graphite in a suitable atmosphere to produce a steel. Two types of iron powder have been studied, electrolytic and reduced. The sintering of mixtures of loose carbonyl iron and carbon black for several hours at 1000° to 1100°C. (1830° to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.1 Trail' has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- [ ] gested by Goetzel,3 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,4 who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Koehring,5 Allen,6 Balke,7 Wulff,8 Boegehold,9 and others. 10,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production because of the lubricating action of the

Jan 1, 1946

Long range expansion plans begun in 1966 by The International Nickel Co. of Canada, producer of over 50% of the free world supply of the white metal, are so mammoth as to give rise to the speculation that something might have to burst at the seams. From an annual level of capital expenditure of $35 to $70 million, the company jumped in 1967 to $145 million in new capital investment and will come close to $200 million in 1968. Inco expects to spend $700 million in the next five years, beginning in 1968, for new mines and surface facilities in Canada. The program involves the opening of nine new mines within the next 3 1/2 years, expansion of producing mines, and construction of new plants and modernization and expansion of established ones to process the increased ore production. Beyond this, the company is committed deeply in developing new sources of nickel abroad. Any one of these new projects, if proven economic, would necessitate expenditures of about $100 million or more. For Inco, the economic strain was relieved without a rupture this spring when Henry S. Wingate, company chairman, reported' at the stockholders annual meeting that $150 million had been raised by the sale of bonds. This marked the first time in 32 years that the company had gone into debt.

Jan 10, 1968

By R. W. Diamond

Three mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the St. Eugene Concentrator, Moyie, B. C., and (3) the Tadanac (Customs) Concentrator, Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals —lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential flotation.

Jan 1, 1928

By Richard B. Greenwalt

INTRODUCTION Direct reduction of iron ores has unquestionably become established as an important step in the worldwide steelmaking industry. The history of this development has been long and fraught with difficulty. In 1800, Champlain suggested the direct reduction concept using carbon and a shallow hearth vessel. Roughly 100 years later, Jones attempted a commercial process using carbon and producer gas in a rotary kiln. During the early years of this century, numerous attempts were made to start commercial direct reduction plants using such processes as Hoganas, Wiberg, Krupp-Renn, and others. Most of these were short lived, being abandoned due to a variety of technical and economical factors. Today, however, a new generation of direct reduction processes has emerged. We enter 1977 with at least 40 commercial plants in operation using 15 processes in 14 countries. These plants have combined total annual capacity of roughly 10 million tonnes of direct reduced product. Many articles have been written, and projections made, concerning the future growth potential for direct reduction. As is al- ways the case with projections, the numbers vary, but the outlook does not. Anyone who participated in the years of effort that have gone into this field of endeavor should be excited and justly rewarded by noting the shape of the curve in Figure 1.

Jan 1, 1977

By D. K. Crampton

THE object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. PREPARATION OF MATERIAL A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and 3/4 in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1.

Jan 1, 1932

By AIME AIME

SOMETIMES family backgrounds have a deep, if not direct, influence on a man's lifework. Dean Callen's paternal grandfather came from Wales and was a mine official in the Pennsylvania anthracite field: his maternal grandfather was a retail coal dealer. His father and uncle began their careers a. breaker boys but later completed their educational work and ended up in the professions. With that background, and with the slate region ( Pen Argyl, Pa.. July 1;. 1888) as his birthplace it is not strange that "Cope" Callen became a teacher of mining engineering. Graduating from Lehigh with an E.M. in 1909, lie taught there for two years while working for his master's degree. In 1911 he returned to teaching, going to the University of Illinois as instructor in mining engineering. In 1917, he was called to West Virginia University as head of the department of mining engineering and director of mining extension. The extension work was about dead. bus a new staff was built and the six-weeks' short course in coal mining was revamped into an attractive and efficient course which has grown in popularity with the years. Callen's work attracted the attention of the Federal Board for Vocational Education and in 1919 he was invited to serve that board as special agent for mining, taking a six-months' leave front the University.

Jan 1, 1944

By Chi-shing Wang

The late Professor P. B. Bucky of Columbia University introduced the principles and techniques of barodynamic experimentation in early 1931 by the application of centrifugal loading to achieve dynamic similitude between models and prototypes of mine structures.1 Later, he and his associates introduced the combined experimental technique of photo- elasticity and the centrifuge to determine the stress distribution in civil engineering structures and mine workings by the use of transparent bakelite models.2,3 The photostress technique, also known as the birefringent-coating method of photoelastic stress analysis, dates back to 1930, when Mesnager published its principles.4 Since then it has been widely applied to experimental stress analyses in many industries. A practical method of observing the dynamic behavior of opaque mine models, which are made of prototype materials, by means of a combination of the centrifugal and the photostress techniques is a new experimental approach under development at the Henry Krumb School of Mines, Columbia University.5 This paper summarizes the development of the barodynamic photostress technique and presents the information obtained from a recent series of experiments in the study of the behavior of rock beams loaded by their own weight. THEORETICAL BACKGROUND Theory of Pure Bending In the general theory of strength of materials, the flexure stress at any point in a beam of any type of cross section which has a longitudinal

Jan 1, 1968

By C. R. Austin

IN a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreas-ing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any, endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test has also shown promise as providing a "merit index" of high-temperature serviceability.2 Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350° C. (and a maximum of

Jan 1, 1934

By S. R. B. Cooke, R. O. Huch, C. S. Chang

IN the flotation of iron ores laurylamine derivatives have been used for considerable time.1, 2' To effect satisfactory separation of the gangue, pre-dominantly silica, from the iron oxide minerals, the addition of specific depressants for the iron oxides has been found necessary. Starches and starch products have been used for this purpose.V here is, however, very little published information on the effects of these materials and other variables on this process. In some cases it has been found that prior acid scrubbing and desliming are essential," and depending upon the efficiency of the subsequent washing step, there will be accompanying changes in pH. It was the object of this investigation to test and observe the effects of the above factor as well as to examine and compare the action of various starches and starch products. Ore Preparation The ore used in this experiment was a wash-ore tailing obtained from the western Mesabi range. Microscopic examination and x-ray analysis of the ore showed it to consist of hematite, goethite, and quartz. Physical properties of the iron minerals ranged from hard and crystalline to earthy and ocherous. The quartz grains were discolored either because of iron-oxide inclusions or because of a sur-face coating of iron oxide. The ore assayed 27.52

Jan 1, 1954

By H. M. Crankshaw

THE early methods of mining anthracite in the steep pitching Mammoth bed consisted in driving breasts up the pitch from the gangways and airways driven in the bed along the strike (Plate 2, Fig. 1). Breasts are simply rooms driven up the pitch the full thickness of the bed (Plate 2, Fig. 2), having a width of from 18 to 30 ft., and a manway or traveling way on one or both sides. (For detail of breast method see Whildin, Trans., vol. 50, p. 704). Many difficulties were encountered, and the maintenance cost of the timbered gangways was so great as to be practically prohibitive. To reduce this .expense, the gangways were driven in the thin Skidmore bed underlying the Mammoth, and the coal mined through rock holes. (Plate 2, Fig. 2;-A.) It was found that after the breasts were driven up 80 to 100 ft., the coal almost invariably rushed or "ran away," making good ventilation almost impossible and the extraction of coal from the upper portion of the lift very difficult. The economic length of a lift is from 200 to 250 ft., and the percentage of extraction by the old method above mentioned was often under 50 per cent., while the coal recovered was so badly broken up as to reduce materially the percentage of large sizes.

Jan 7, 1916

By C. Schlumberger

IN the course of the past few years the authors and their associates have had different opportunities to study the electrical phenomena which accompany the oxidation of pipe lines. The causes of such phenomena are very similar to those which have been described under the name "spontaneous polarization" with reference to metallic orebodies,1 and can be investigated in the same manner. These investigations, however, until recently were of a scientific and theoretical character, and had not found any important practical application. During the year 1931, however, the authors treated several industrial corrosion problems for public utility companies. These problems usually had to be studied in towns or in densely populated areas, where it was well-nigh impossible, or very expensive, to dig pits and trenches in order to make electrical measurements on the pipe itself. The authors were thus led to evolve a method and apparatus permitting the study, from the surface, of the direction of the currents flowing from pipe lines. The purpose of the present paper is to discuss the results obtained in the course of these investigations. However, in consideration of the importance and interest of the work carried out by other scientists along the same lines, a separate chapter will be devoted to a summary of the results achieved up to the present time in the study of pipe line corrosion.

Jan 1, 1932

By Robert A. Rapp

The standard molar free energy of formation of MOO,was determined between 750o to 1050o C in galvanic cell measurements involving the solid electrolyte Zr0.85 Ca0.15 O1.85. Use of the reference electrodes Fe + FexO and Ni + NiO Provided two independent determinations of FoMoo2. The data may be represented by the equation FMoO2 = -137,500 +40.0T(°K) which is in good agreement with previous CO/CO, gas equilibrium measurements of Gleiser and Chipman. The standard molar free energy of formation of molybdenum dioxide has recently been reported over a large range of high temperatures from the calorimetric experiments of King, Weller, and christensen.' Gleiser and chipman2 have also recently determined ?FmoO2 from 926o to 1068oC in CO/CO2 gas equilibrium measurements. Earlier gas equilibrium studies have been made and reviewed by Gokcen.' Over the temperature range studied by Gleiser and Chipman their values for ?FoMoO2 differed from the calorimetric data by about 700 cal. This investigation was undertaken to resolve this difference and thereby establish the two phase mixture of Mo + MOO, as an electrode of well-known oxygen potential for galvanic cell applications at very high temperatures. The galvanic cell technique involving the Zr,.,, Ca,0.15 01.85 solid electrolyte was introduced for the

Jan 1, 1963

By K. Matsuda, H. Tanaka, M. Mamiya, H. Majima

Copper cementation was studied from both thermodynamic and kinetic aspects. The temperature effect of copper cementation, which has been recognized as an anomalous result, and the rate enhancement phenomenon observed after the initial linear step are, in particular, focused in this work. The main results obtained are as follows; 1) Free energy changes of copper cementation reactions, calculated by the use of the "Correspondence Principle" of Criss and Cobble are rather insensitive to temperature. 2) A Flow-cell assembly consisting of a special cupric ion electrode, a calomel electrode and a potentiometer is particularly useful for the continuous measurements of copper cementation rate. 3) Two first-order reaction rate constants for the CU2+- Fe system were successfully determined by the use of the flow-cell assembly. 4) Activation energies determined for the initial rate and the 9 maximum rate of CU2+ - Fe system are both 4.6 kcal/mole. This fact suggests that the mechanisms of the initial reaction and the final reaction are essentially the same and both reactions are rate controlled by the diffusion in a boundary layer. The difference in the rate constants of them may fie explained by the effect of the nature of surface deposits. 5) Qualitative explanation of the rate enhancement phenomenon from the initial rate was successfully made by applying Bockris "Penetration Model."

Jan 1, 1976

By J. B. Hiskey

The hydrometallurgical application of thiourea in processing precious metal ores and concentrates has reached the development stage. This paper reviews recent technical literature covering the process development of thiourea leaching. In addition, recent fundamental contributions are discussed. Most of the interest in thiourea leaching has involved treating high grade concentrates that have sufficient value to just the use of thiourea as a reagent. An important development in thiourea technology is the addition of SO2 to the leaching solution. This procedure effectively reduces the decomposition of thiourea and eliminates the problems of passive surface layers that limit the leaching efficiency. Results for the thiourea leaching of a bulk sulfide concentrate and a residue from the autoclave leaching of a smelter flue dust are also reported. As determined by a standard bottle roll cyanidation test, the bulk concentrate was extremely resistive to cyanide leaching yielding only 16% gold and 2% silver extraction in 24 hours. Leaching with a relatively concentrated thiourea solution (1MCS (NH2)2) resulted in 83% gold and 75% silver extraction in four hours. With the treated flue dust residue, gold extraction was about 60%. Gold and silver extraction with cyanide was sensitive to both cyanide concentration and oxidizing conditions. Cyanidation resulted in 59% gold extraction and 77% silver extraction in 24 hours.

Jan 1, 1985

By Persifor Frazer

(Read at the Wilkes-Barre Meeting, May, 1877.) A CLASSIFICATION of natural objects is usually based either upon some fundamental and permanent attribute of the thing itself (as in the case of scientific classifications), or it embraces one or more generalizations convenient for use in ordinary life. Thus, it suffices for the statistician to, know that so many tons of fish are annually taken by our fishermen, and that they realize so many thousands of dollars, whereas to the student of natural history the anatomy, habits, and relationships of the animals are of chief interest, as settling their respective places in the scale of animate nature. Many different classifications of coals have been attempted, as one would naturally anticipate from the immense extent of the coal trade, and the different localities whence the supply was derived. The English divisions were prevalent up to the date of the publication of the last geological survey of the State, except so far as they were modified by local designations. Indeed, Rogers' classifications made very little alteration in the English nomenclature, as may be seen by comparing. the tables given below. To commence with the different kinds mentioned in Ure's Dictionary of Arts, Manufactures and Mines of 1845 " 1. Cubical Coal.-Black, shining, compact, moderately hard and easily frangible. Comes out in rectangular masses, of which the

Jan 1, 1878