Search Documents

By G. G. Marino, J. W. Mahar

This paper provides an understanding of the behavior and potential damage of homes resulting from sag-type mine subsidence. This is done with extensive research of numerous case histories in Illinois collected by the authors. The house response to subsidence-induced ground displacements are summarized and evaluated. A damage level criteria, specifically developed for residential structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 1, 1986

By Milnor Roberts

WAR struck the mineral industry of Washington with cross currents that produced a peculiar result. The State's production of coal, industrial minerals, and metals for 1941, valued at $28,507,282, was increased in 1942 under war pressure to approximately $35.000,000. Meanwhile a tremendous demand had arisen for men to construct airfields and many other large projects for the Army and Navy in Washington and Alaska, and Government plants for the mineral industry costing $140,000,000 or more, as well as a call for employees in the U. S. Navy Yard at Bremerton, the sixty shipyards, the four Boeing airplane factories with many auxiliary shops, and hundreds of other plants turning out war materials. In spite of an influx of nearly 300,000 people, causing an increase of 17.1 percent in the population since 1940, according to the Census Bureau, the State clearly is still engaged in an unusual amount of war production in proportion to its population. A large proportion of the workers have been drawn from the mineral industry to the war plants, whether through motives of patriotism, high wages, or, in the Boeing plants at least, the glamour of the operation

Jan 1, 1944

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

By W. H. Bassett, C. H. Davis

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other. words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. . In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1928

By Frank Rieber

THE discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the, surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.1 The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment Is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as -is possible with the more pronounced anomalies.

Jan 1, 1928

By William G. Pariseau

Advances in numerical methods of analysis and computer technology during the past decade have brought many formerly intractable ground control problems within easy reach of present day graduate mining engineers. However, the new technology brings with it new problems. The identity of these problems are largely those arising from a lack of familiarity with the capabilities and limitations of the new technology. In this regard, the central problem in ground control planning is the calculation of ground motion associated with mining. The fundamentals of this problem leading to a form suitable for computer programming are therefore reviewed. Solution procedures in the broad sense including the gathering of input data and the interpretation of output are described. Computer program capabilities necessary for ground control analysis are discussed and the steps necessary to implement an analysis are outlined.

Jan 1, 1983

By Carl Swartz

METALLURGISTS differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a one-millimeter screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in, color, having the general characteristics of a spinet Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution zinc values tied up in this compound remain behind. HISTORY In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite, others merely a mixture of zinc and iron compounds.

Jan 1, 1927

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By David Kramer, Cecil G. Rhodes

Critical transport currents were measured as a function of perpendicular external magnetic field in Ti-22 at. pct Nb wire samples. These samples were heat-treated to yield w Phase precipitates at denslties ranging from 10 to 10 17cm-3. The Precipitates are ellipsoids of revolution with major axes of 50 to 1300A. Flux-Pinning by w precipitates is responsible for the high critical transport currents that were ob- ThE ability of a type II superconductor to sustain a zero-resistance transport current (Jc) in an external magnetic field (H) is due to the presence of micro-structural features which can impede the motion of magnetic flux penetrating the superconductor under the influence of a Lorentz force. Such features are referred to as pinning sites. The pinning strength is tained. A sample cooled from 800°C and annealed 1 hr at 450°C carried a critical tramport current of 10 amp per sq cm at 30 kG. Variations in the current-carrying ability of this alloy are due to changes in its pinning strength which is a function of precipitate density and composition and of the composition of the matrix. the reaction of the bulk superconductor to the Lorentz force and depends on the efficiency of the individual pinning sites and on their volume density. The super -current density increases with pinning strength, other things being equal. The above concepts are discussed in detail in a comprehensive review by Livingston and Schadler.' In Ti-Nb alloys, as in other binary titanium alloys, the metastable hexagonal w phase usually forms below the p/a + p phase boundary near the titanium side of the phase diagram. Stiegler et a1.' have summarized much of what is known about w phase in titanium and zirconium binary alloys. The present work deals with

Jan 1, 1968

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By Samuel B. Christy

As is well known, the ore at New Almaden is cinnabar. Native quicksilver occurs also; but, as a rule, in small quantities only. Pyrite occasionally accompanies the ore. Bitumen is quite common,

Jan 1, 1885

By W. M. Weigel

Economic deposits of barite occur in Missouri in two main districts. The most important, the Southeastern or Washington County district, is in the southeastern part of the state, mostly in Washington County with a small extension into the northeastern part of St. Francois County. Roughly, it embraces nine townships or about 200,000 acres and accounts for from 80 to 90 per cent. of the state production. The Central district, is in the central part of the state, includes most of Morgan and Miller counties, and parts of Camden; Benton, Moniteau and Cole counties. The area embraced is much larger than the Washington County district, but the deposits are more infrequent. The location and general area covered by the two districts is shown in Fig. 1. There is another small area in southern Franklin County but so far its production has been of small consequence. It might be considered as a northward extension of the Washington County field. An, area in the central part of Hickory County has also produced a small amount. The outline of the districts as shown indicates the general area in which deposits have been found. The total area covered by deposits of barite is only a small part of this, as, in the Central district especially, there may be miles of supposedly barren areas between ore-bearing areas of an acre or two in extent. The date when barite was first mined in Missouri cannot be definit stated, but the industry probably dates back to about 1860. The occurrence of barite was known long before this, as it was encountered in the lead mines in Washington County and mentioned by several earlier writers." Missouri is reported as producing 8000 tons in 1882 so it is evident the industry was well under way in the seventies in order to have arrived at this substantial production. By 1893 Missouri production had increased so that it ranked with that of Virginia, then the largest producer it increased until in 1914 Missouri accounted for about 65 per cent. of the total United States output.

Jan 1, 1929

By L. A. Norman

ANOTHER chapter in the history of Mother Lode mining is being written by operations in the Old Eureka mine near Sutter Creek, Amador County, California. During a two-year period (1938-1939), 85,517 tons of ore averaging 0.62 oz. gold per ton were mined and milled, as compared to the production of approximately 210,000 tons of 0.315-oz. gold ore during the preceding seven years. This is a repetition of mining history in the Mother Lode, where a period of prosperity has followed a long period of lean production. The location of this new ore in the hitherto unproductive hanging-wall greenstones and its mining and geological developments are most interesting. HISTORY OF THE OLD EUREKA MINE The Old Eureka mine, also known as the Hayward, Eureka, Hetty Green and Amador Consolidated, is in the most productive 10-mile length of the 120-mile long Mother Lode of California. The mine was first opened in 1852 with operations more or less continuous for the next 30 years. Production during this period amounted to $12,000,000 from an ore shoot 500 ft. long, which bottomed 1700 ft. below the surface. The shaft was continued as a prospect to 2065 ft. on the incline, where work was stopped in 1881. The mine was sold in 1916 by Hetty Green and the shaft deepened to the 3500-ft. level (3212 ft. vertically) by the new owners. Drifts were run on the 1700, 2100, 3000 and 3500-ft. levels, together with approximately 1500 ft. of crosscuts. No ore was found and work was abandoned in 1921. The present owners, the Central Eureka Mining Co., purchased the mine in 1924 after threatened litigation over rights to the rich ore shoot being mined from the lower levels of the Central Eureka mine on the south. Rehabilitation of the shaft commenced in 1926 and in 1930 mining on the old 2100-ft. level was started. While efforts of the previous owners had been directed for the most part toward the area south of the Old Eureka shaft and adjacent to the productive Central Eureka mine, the present owners started drifting northward on the old 2100-ft. level. On the 2000-ft., 2100 and 2300-ft. levels, drifts were run in part along the

Jan 1, 1939

Jan 1, 1915

By AIME AIME

DESTRUCTION of the plants, machines, utilities, tools, materials, and other essentials for peacetime living penalizes not only the owners of the materials destroyed, but the world as a whole. Specifically, the fundamental fallacy of any proposal for the in- discriminate destruction of the German industrial system is that it fails to differentiate between the wartime and the peacetime economy of the Reich. We are for one simple, clear objective-an effective industrial means to keep Germany from starting another war. This objective should not be con- fused, especially before the war is even won, with the appropriate punishment of Germany or with the international arrangements for the long future to be made around the peace table by the representatives of the Allied Nations after victory is achieved. This paper, therefore, does not deal with broad, complex postwar questions of diplomacy and international policy. "Unconditional surrender" implies disarmament of the German armies, the surrender of all arms, munitions, air- planes, and other ordnance material in stock piles or in process. It also should include the elimination of all German war production facilities, such as ordnance plants, munitions plants, and submarine works, and the control of raw materials required by war industries.

Jan 1, 1944

By John E. Hagni, Richard D. Hagni

ORE.ID, a microcomputer program, rapidly searches a database of the principal properties for 573 ore minerals. Searches may be performed on any or all of the following properties: mean Vickers hardness, Talmage hardness, mean reflectance, strength of anisotropism, and colors and tints of the mineral and its internal reflections. Data from the International Mineralogical Association - Commission on Ore Microscopy data card file have been used when available. The program displays the number and type of data matches for each mineral found, displays their chemical components, and allows the range to be narrowed or widened for each of the identification properties for repeated searches, if desired. ORE.ID is much more rapid, allows for the use of more identification properties, and involves more ore minerals than any previous identification system.

Jan 1, 1985

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By E. B. Spice

Although much may be learned about the economics of cold weather operations by studying successful mining ventures in southern and central Canada, it is the purpose of this article to extend the study by considering only permafrost areas. Geographically this means most of the country north of the 60th parallel. In this area, at the present time, only five Canadian companies are carrying on routine and successful mining operations on a year-round basis. However, there have been some score of unsuccessful ventures, and a number of properties in the development stage show promise of being producers. Problems of cold weather are worthy of study. It may be pointed out that successful mines in this area face problems of isolation and costly transportation as well as cold weather. To reach valid conclusions, consider the development of a mythical mineral deposit located on the 65th parallel in the heart of the barren lands; problems of isolation and transportation will be ignored.

Jul 1, 1956

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948