Search Documents

By E. C. Burke, W. R. Hibbard

Plastic deformation in magnesium single crystals was studied by tensile tests at room temperature utilizing an improved preparation and testing technique. Consistent critical resolved shear stress values for basal slip were obtained. The advent of pyramidal slip at room temperature was rationalized upon the basis of grip constraints. A bend-twinning hypothesis was advanced as an explanation of mechanical twinning which occurs as a complex stress-relief mechanism. INVESTIGATIONS of the plastic deformation of magnesium have been limited to the determination of the fundamental kinetics which may be summarized as follows: 1—Twinning on the {102).l 2— Slip on the (001) plane in the [loo] direction at room temperature.' 3—Slip on the {101) or {102) plane in the [loo] direction above 225°C." 4—Critical resolved shear stresses for basal slip in tension at room temperature of 83 g per sq mm with a variation from 57 to 127 g per sq mm." Bakarian' studied the compression of thin wafers of magnesium single crystals and classified the components of the deformation mechanisms as follows: 1—The Basal field: (001) at an angle of less than 20" to the compression surface. Fracture along {101} or slip on (001) followed by {101} fracture. 2—The prism field: (001) at an angle greater than 60" to the compression surface. Twinning on the {102) generally occurring during the early stages of loading, basal slip in the areas of original orientation and (001) slip within twins. 3—The central field: (001) at angles greater than 20" but less than 60" to the compression surface. Slip on the (001). 4—The critical resolved shearing stress for {101} slip above 225°C was 400 g per sq mm. Observations of mechanical twins in hexagonal close-packed metals have been summarized by numerous investigatorsb-' emphasizing a lateral or rotational atomic adjustment, in addition to the pure twinning shear, and the importance of reorienting the basal plane to a position more favorable for continued slip, rather than the resulting small dimensional changes. Criterion for the operative twinning planes has not been clearly established. Schmid and Boas hurmised that an energy condition related to the atom movements is the determining factor. MillerQ bserved that twinning stresses in zinc crystals decreased as the amount of prior deformation increased. Preparation of Specimens Magnesium single crystals % in. in diam x 8 in. long were grown from the melt under an argon atmosphere in a gradient furnace similar to that described by Jillson." Magnesium containing 0.018

Jan 1, 1953

By Jack A. Simon, M. E. Hopkins

GENERAL GEOLOGY Coal is defined as a combustible rock that had its origin in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the somewhat unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks being returned to earth will, we hope, provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust of the earth is not completely stable, and throughout the geologic past portions of the crust have moved laterally and vertically. Even today, many coastal areas are slowly rising or sinking. More sudden earth movements are recognized by the earthquakes they cause. Throughout geologic history, rises in sea level or the sinking of the land areas have many times permitted the oceans to cover much of what are now the areas of the continents. Only relatively small parts of the present continents appear to have been above sea level throughout geologic time. Great

Jan 1, 1973

By AIME AIME

DESTRUCTION of the plants, machines, utilities, tools, materials, and other essentials for peacetime living penalizes not only the owners of the materials destroyed, but the world as a whole. Specifically, the fundamental fallacy of any proposal for the in- discriminate destruction of the German industrial system is that it fails to differentiate between the wartime and the peacetime economy of the Reich. We are for one simple, clear objective-an effective industrial means to keep Germany from starting another war. This objective should not be con- fused, especially before the war is even won, with the appropriate punishment of Germany or with the international arrangements for the long future to be made around the peace table by the representatives of the Allied Nations after victory is achieved. This paper, therefore, does not deal with broad, complex postwar questions of diplomacy and international policy. "Unconditional surrender" implies disarmament of the German armies, the surrender of all arms, munitions, air- planes, and other ordnance material in stock piles or in process. It also should include the elimination of all German war production facilities, such as ordnance plants, munitions plants, and submarine works, and the control of raw materials required by war industries.

Jan 1, 1944

By N. H. Emmons

An interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at its plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory. Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaccs. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top mas necessary and the engineering force was started on the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of east copper, but the heat was great that the copper bent readily, due to the jarring of its

Jan 1, 1911

Escalating energy costs and tough environmental standards were two major factors affecting the minerals processing area in 1978 For the most part, new startups and research and development initiatives were directed toward improving process dynamics, investigating alternative processing strategy, and lowering unit costs. In the flotation area, the trend to larger machines continued. Scientific investigation of the modeling and process control of flotation was apparent, as was the research and development of new flotation reagents.

Jan 5, 1979

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By D. C. Lindley, D. H. Gaucher

The displacement of oil by water in a waterflood project is accomplished by the action of transient viscous, gravitational and capillary forces which drive fluid through interconnecting pore spaces toward production wells. The relative importance of each of these forces to the effectiveness of the displacement and the production history depends on properties of the reservoir itself and the manner in which it is operated. There has been considerable discussion'-3 concerning the importance of these factors and the extent to which they control the performance of individual waterflood projects. No data have been presented, however, to demonstrate the effect on waterflood behavior of variations in rock permeability, water-injection rates and mobility ratios in three-dimensional reservoir systems in which viscous, gravitational and capillary forces are allowed to assume the proper relative influence on fluid flow. Much information relevant to water flooding has been gained from the study of field case histories. But, the complexity of the systems involved, the difficulty of defining geometry and obtaining sufficient data, and the fact that the same reservoir is never flooded twice with the same initial conditions, all obscure the role of process variables such as rate. Further, mathematical calculations of waterflood behavior are restricted at this time by available mathematical techniques to highly simplified situations. Scaled models, however, do offer an approach at the present time to evaluation of the effects of the pertinent variables. Several investigators have predicted prototype reservoir behavior from observations of model waterflood performance under a variety of conditions. Two-dimensional aspects of waterflood pattern efficiency have been investigated by Muskat, Aronofsky, Dyes, et al, raig, et al,' and Rapoport, et al. he effects of gravity segregation, viscous fingering and permeability stratification have also been studied in two-dimensional models. Craig, et al," studied the importance of gravitational forces on frontal displacement in three-dimensional models with wells on a five-spot pattern. This work in- vestigates the tendency for water to segregate in homogeneous reservoirs because of gravity and to under-run the oil for a range of water-inject ion rates. The effects of permeability stratifications were investigated by these authors using miscible fluids to simulate water-channeling through permeable strata in systems of negligible capillary force. In this investigation, a three-dimensional model of a five-spot pattern flood was designed to represent typical prototype conditions, and the sand and liquid properties were selected so that capillary, gravitational and viscous pressure gradients were scaled. It was not, however, possible to achieve exact similitude regarding viscous fingering when the more viscous oil was used. The effects of rock stratification on waterflood behavior were studied by changing both the permeability ratio and the position of the more permeable sand stratum in a two-layered, horizontal model. For each type of stratification, constant-rate floods were performed and the rates were varied, in separate experiments, over a tenfold range. To observe the effect of mobility ratio on flood performance, two series of constant-injection-rate floods were performed on the most highly stratified reservoir at a water-oil viscosity ratio of one.

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of vary-ing thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition.

Jan 1, 1939

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By Stewart R. Wallace

Members of the Society, it is a very great honor for me to be here today and to have the opportunity of telling you about some things that have been accumulating in the back of my mind for some time. Before attempting to do so, I should acknowledge my debt to the many people who are responsible for my presence here this afternoon. To do this properly, however, would consume much of my allotted time and I will therefore mention only two men, both of whom were directly involved in the discovery of the Henderson ore body. The first of these was Robert Henderson, now dead, who at the time the work was going on was vice president of Western Operations of the Climax Molybdenum Co. Truly, he provided the environment that permitted the exploration program to function effectively, and the deposit appropriately bears his name. The second man I meant to mention was resident geologist at Urad at the time of the Henderson discovery. I think I should explain right here that the Urad ore body and the Henderson ore body, although entirely separate, are closely related deposits, and that both are located at Red Mountain in Clear Creek County, Colo.

Jan 6, 1975

By Philip Bucky

THE term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater mecha-nization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar model built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimensions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein.

Jan 1, 1938

By Samuel Hoyt

THE writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + ß range, first described in 1913. These notes are offered, not at all as the final explanation of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520° C. and the other at about 600° C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600° C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600°. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + ß range and increased in magnitude with the amount of a up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + ß field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 12, 1918

By David Sinclair

THE dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests.§ None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their appli-cation in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I THE PHOTOELASTIC METHOD The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution.

Jan 1, 1940

THE first session was held in the small hall of the Academy of Music, on Tuesday evening, February 18th, 1879. The proceedings were opened by the reading, by President Eckley B. Coxe, of the following Address : SECONDARY TECHNICAL EDUCATION. Technical education is a subject to which both the American Institute of Mining Engineers and the American Society of Civil Engineers have of late years given much attention, and deservedly so. We all remember the admirable address of our former President, Mr. Holley, at the Washington meeting, upon this subject, and the very interesting reunion of the two societies in Philadelphia for its discussion. The problem to the solution of which the meeting devoted its attention was, "Shall the practical education of the engineer in the mine, in the rolling-mill, in the workshop, or in the field, precede, be contemporaneous with, or follow his theoretical studies in the technical school ?" I do not propose to add anything to what was so admirably said by so many of our leading engineers on that occasion ; but I shall ask your attention to another question in technical education, which seems to me equally worthy of our consideration, and which, I am sorry to say, has as yet attracted but little attention in this country. It is, "Shall the apprentices (I call them so for the want of a better general name), who are growing up and learning their trades in and around our mines and works, and from whose ranks the master mechanics and foremen of the future must be taken-shall they be provided with some means of obtaining as much theoretical training as may be necessary to enable them properly to understand the various processes and operations that they may be called upon to superintend, and not be obliged to pick up, as best they may, here a little and there a little truth mingled with much error?" In the former case, those who have the ability and industry to avail themselves of the advantages that should be offered to them would fit themselves to become real foremen, men who would understand and appreciate the true engineer and his methods. Of late years the young men of this country who have wished to enter our profession have had great facilities offered to them for so doing ; there have been undoubtedly great improvements in the methods of instruction; and although I am very far from imagining that no further progress can be made, or is demanded, yet I feel sure that

Jan 1, 1879

By S. A., Taylor

IT is very difficult to arrive at exact figures for the cost of maintaining excess capacity of coal mines, but we can approximate the various items. To do this, I will take the Pittsburgh district of Pennsylvania and the other districts can be compared to this one. I believe we can take the depreciation item of plant ac- count as a whole and discount it over a period of 20 years; while this is high for some items it is low for others and I believe it is not far from a safe basis. This equals 5 per cent per year, and this depreciation will take place about as rapidly when not in use as when in operation. A fair value in the Pittsburgh district to- day for plant and houses is close to $4 per ton per annum. At 5 per cent this will equal 20 cents per ton per year. The item of keeping the mine in condition, free from water, etc., will be close to an average of 2y2 cents per ton per annum.

Jan 1, 1928

By W. E. Ruder

It has been pointed out by Stead1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly' well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Ar2. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703" C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750" C. for 0.5 per cent. Si to 860" for 6 per cent. alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730" and 750:. In the preliminary experiments, some of which have been described in a previous paper, it was found that practically all of these steels, when annealed to 1,200" C. or higher, showed grains of comparatively large size. These grains varied in size, however, from about 4 sq. mm. to 50 sq. cm. (see Figs. 1 and 2) under the same conditions of anneal, and it was for the purpose of determining the cause of this difference in size that the experiments herein described were undertaken. From a preliminary study of the chemical composition of the specimens

Jan 1, 1914

By John Chipman, Theodore B. Winkler

IN order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chipman,3 dealt with the simplest possible slag system that would resemble those found in the basic open hearth-the slag system consisting of CaO-MgO-SiO2-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemistry of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, Si02, FeO, Fe203, P205, MnO, A1203 and CaF2, but not all of the slag samples contained all of these components at one time. REVIEW OF LITERATURE Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Brings4' von Samson-Himmelstjerna,5 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution ratios

Jan 1, 1946

Jan 1, 1879

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949