Search Documents

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200' to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By Harold R. Bradford

EXPANSION initiated during and after the war has placed industrial plants in new areas and increased reduction and manufacturing facilities in communities already established. With added expansion interest has grown in possible area contamination from waste products. Evolved flue waste contains many chemical contaminants that may or may not cause concern; however, atmospheric pollution has always been a problem to industrial communities. For some time effects attributed to small quantities of compounds of fluorine in various waste gases have been studied by industrial, medical, agricultural, and associated interests.1'2 Aside from an article by Churchill, Rowley, and Martin in 1948," little has been published on the subject of fluorine in coal except by foreign investigators. The first indication of fluorine compounds in coal was noted in England in 1934 by R. Lessing,4,5 who found that the presence of fluorine in Midland and West County coals was definitely established by etching of glass and by severe corrosion of porcelain fillings in a gas works scrubber. Etching of glass in a direct contact annealing kiln initiated research, and in 1944 four papers were published by H. E. Crossley,6-9 giving results of investigations of fluorine in coal of England by the Fuel Research Board, Department of Scientific and Industrial Research. These investigations studied methods of determining fluorine, the quantities present in various coal deposits, the geographical distribution of fluorine in British coals, occurrence of fluorine in minerals associated with coal, amounts of fluorine compared to other constituents of coal, the nature of fluorine compounds, and industrial significance of fluorine in coal. It was shown that British coals contain from 5 to 200 ppm of fluorine, which is probably present as fluorapatite [Ca10F2(PO4)6], often written as [3Ca3P2O8.CaF2]. The fluorapatite is intimately associated with shale in some coals and can often be separated from these coals along with the shales. H. E. Crossley8 also reported no correlation between the amounts of chlorine, sulfur, or ash and the amount of fluorine in different coals. He found, however, a relationship between the content of fluorine and phosporus in many British coals. Thus it should be possible to anticipate likely fluorine-rich coals from existing data giving phosphorus content. Behavior of the fluorine compounds of coal was compared with that of 12 fluoride-phosphate minerals in sink-float separations and solvent ex-

Jan 1, 1958

By A. Karim, T. G. Langdon, C. Y. Cheng, J. E. Dorn

The effect of changes in temperature and stress on the creep behavior of Fe-4 pct Si was investigated over the temperature range from 650° to 1175K Over the temperature range of 799° to 110l°K, the shear strain rate, ?', obeys the relationship: where K is a constant, 7 the applied shear stress, G the shear modulus, g the free activation energy for diflusion, R the gas constant, and T the absolute temperature. The results strongly suggest that the creep in this alloy is controlled by a dislocation climb mechanism. In a recent investigation, Ishida, Cheng, and Dorn1 observed that the apparent activation energy for creep of a! Fe from 480" to 775°K corresponded to that for self-diffusion. Over the magnetic transformation range (775" to 1045"K), the apparent activation energy for creep increased steeply with increasing temperature in agreement with the known decrease in the free activation energy for self-diffusion. Passing through the Curie temperature, the apparent activation energy decreased abruptly following which it then increased mildly as the temperature further increased. Inasmuch as the apparent activation energy for creep of a! Fe below the Curie transformation range of temperatures appeared to decrease with increasing values of the stress, the data were analyzed in terms of a model based on the nonconservative motion of jogged screw dislocations. But since the observed creep rate was much higher than that which could be accounted for on the basis of usual models, the authors found it necessary to assume that pipe diffusion became significant over the lower temperature range. Furthermore, the abnormally high activation energy for creep above the Curie temperature was attributed to grain boundary migration which became prevalent in this temperature range. It was thought that a number of the interesting issues that arose in the creep of a Fe might be resolved by investigating the creep of Fe-4 pct Si alloy: This alloy has about the same Curie range and therefore should give creep results that closely parallel those for a Fe and in this way provide comparable data for analysis of creep mechanisms. Furthermore, it can be annealed at higher temperatures which could provide some stabilization against grain boundary migration. In addition, it might serve to illustrate the possible effects of short-range ordering on creep.

Jan 1, 1969

By A.E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By David B. Reger

The discovery of prolific oil wells in old territory hitherto regarded as doubtful, if not worthless, and the rapid extension of a gas pool opened late in 1938 were the most interesting petroleum features in West Virginia during 1939. Oil activity in general was slow because of crude prices that were still fairly low at the end of the year, although substantially increased above those in January. Fewer oil wells were completed, but the average results were better than in 1938. Fewer gas wells, also, were completed, with greatly lessened average initial production. Many old oil and gas wells were abandoned, so that the total number of active wells has not changed appreciably. The account of operations, as gathered from trade journals and other sources, shows that 561 new wells were drilled, resulting in 101 new oil wells with 2261 bbl. of daily initial production; 366 new gas wells with 602,400,000 cu. ft. of daily open flow; and 94 dry holes. Besides these new wells, 61 old wells were drilled to deeper sands, with 12 bbl. and 13,328,000 cn. ft. of added production. On the new wells the oil average was 22.38 bbl. per well per day; and the gas average was 1,645,900 cu. ft. per well per day; the ratio of dry holes to completions was 16.76 per cent. From an exploratory standpoint one partly discredited oil area was revived by good new production, and another small oil pool may have been opened. Some of the results in gas exploration will require more drilling for true appraisal. It is certain, though, that one very considerable gas field in the sands of Mississippian age has been proved; and there is a probability of six new pools in the Middle Devonian shale. In the Oriskany sand (L. Dev.) the Elk-Poca pool has been extended considerably farther northwest into Jackson County; and farther north in Jackson County two widely separated wells, which may be pool openers, have been successfully completed. On the other hand, several important wildcats in various counties have been dry. Stratigraphically lower, some additional wells have been completed in the Newburg sand (Sil.) and one small producer has been completed in the Clinton sand (Sil.), the importance of which can scarcely be overestimated, because no Clinton production has previously been found in the state, although at least seven wells have been drilled through the sand.

Jan 1, 1940

By David B. Reger

The discovery of prolific oil wells in old territory hitherto regarded as doubtful, if not worthless, and the rapid extension of a gas pool opened late in 1938 were the most interesting petroleum features in West Virginia during 1939. Oil activity in general was slow because of crude prices that were still fairly low at the end of the year, although substantially increased above those in January. Fewer oil wells were completed, but the average results were better than in 1938. Fewer gas wells, also, were completed, with greatly lessened average initial production. Many old oil and gas wells were abandoned, so that the total number of active wells has not changed appreciably. The account of operations, as gathered from trade journals and other sources, shows that 561 new wells were drilled, resulting in 101 new oil wells with 2261 bbl. of daily initial production; 366 new gas wells with 602,400,000 cu. ft. of daily open flow; and 94 dry holes. Besides these new wells, 61 old wells were drilled to deeper sands, with 12 bbl. and 13,328,000 cn. ft. of added production. On the new wells the oil average was 22.38 bbl. per well per day; and the gas average was 1,645,900 cu. ft. per well per day; the ratio of dry holes to completions was 16.76 per cent. From an exploratory standpoint one partly discredited oil area was revived by good new production, and another small oil pool may have been opened. Some of the results in gas exploration will require more drilling for true appraisal. It is certain, though, that one very considerable gas field in the sands of Mississippian age has been proved; and there is a probability of six new pools in the Middle Devonian shale. In the Oriskany sand (L. Dev.) the Elk-Poca pool has been extended considerably farther northwest into Jackson County; and farther north in Jackson County two widely separated wells, which may be pool openers, have been successfully completed. On the other hand, several important wildcats in various counties have been dry. Stratigraphically lower, some additional wells have been completed in the Newburg sand (Sil.) and one small producer has been completed in the Clinton sand (Sil.), the importance of which can scarcely be overestimated, because no Clinton production has previously been found in the state, although at least seven wells have been drilled through the sand.

Jan 1, 1940

By A. E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By J. S. Hegwer, P. M. Dunlap

An improved acid for the treatrrzent of sulfate-con-raining limestones and dolomites is described. The acid is designed to reduce he reprecipitation of dissolved calcium sulfate and the possibility of plugging permeable flow channels. In addition, this improved acid has a much lower reaction rate than that of regular acid; the advantages of a "retarded" acid are obtainable. Field testing of the acid has shown it suitable for use in sulfate-containing formations. Substantial improvements in productivity generally resulted. INTRODUCTION Acid treatments of limestones, dolomites and other formations bearing carbonate deposits are frequently unsuccessful when the calcareous formation contains sulfate, either as anhydrite (CaSO,) or gypsum (CaSO4. 2H2O). Preliminary dissolution in acid followed by redeposition of calcium sulfate appears to be a major factor contributing to poor well performance after acidizing. The precipitate is usually the gypsum form of calcium sulfate, but in higher temperature formations it may be anhydrite. The freshly precipitated crystals are nearly always very small and needle-like. They may occupy a gross volume many times that of the original anhydrite crystals and will obviously constitute an impediment to flow through newly enlarged flow channels. It is believed that the redeposition problem is most severe when anhydrite lines the fracture systems and large pores which supply the effective permeability of a formation. Microscopic inclusions of calcium sulfate also present large sulfate surface areas for dissolution in acid. In either case, great amounts of calcium sulfate may dissolve before the acid can be spent on formation carbonates. For regular spent acid (originally 15 per cent hydrochloric acid) the precipitate could be as much as 270 Ib gypsum/1000 gal acid. Two techniques have been applied by the industry for reducing sulfate plugging during acidizing. The method'.' commonly employed in the field is the attempted removal of a quantity of regular treating acid before it has reacted completely with the formation. This is practiced because the solubility of calcium sulfate is greater in a solution that is still acidic than in one which has been largely spent on the formation rock. The chance of precipitative plugging is therefore reduced if the withdrawal is successful. However, it is often impossible to get the acid out of the formation before precipitation occurs. A second possible method, which at first glance appears practical, involves addition to the acid of sequestering agents which form strong soluble complexes with calcium ions. These chemicals do increase the "solubility" of calcium sulfate in fresh acid, but to a lesser extent in spent acid. The sequestering agents have, therefore, proved unsatisfactory because the amount of sulfate eventually deposited from the spent acid may be greater than that from regular acid. Another logical approach to the problem of calcium sulfate reprecipitation is the prevention of the initial dissolution of calcium sulfate by the common ion effect. This may be accomplished by adding a soluble calcium salt to the fresh acid. The use of calcium salts in treating acids is not entirely new. An earlier suggested use of a soluble calcium salt in hydrochloric acid apparently failed to recognize the full extent to which the solubility of calcium sulfate could be suppressed. The present study extends this earlier work and adds certain improvements toward the development of a practical anti-anhydrite acid. LABORATORY DEVELOPMENT Calcium Sulfate Solubility Table 1 shows the results of a laboratory study performed to establish the effect of calcium chloride concentration on gypsum solubility. Because of the strong tendency of calcium sulfate to form supersaturated solutions, accurate solubilities are difficult to determine. These solubility data probably are reliable to within ± 15 per cent. The solubility of calcium sulfate in 15 weight per cent hydrochloric acid increases with increasing temperature. This trend is also followed in hydrochloric acid which cantains calcium chloride. This is contrary to the solubility behavior of calcium sulfate in water, wherein the solubility decreases with increasing temperature.

By J. E. Hilliard

AS is well-known, the length per unit volume, Lv, of any lineal feature (such as grain edges in a polycrys-talline specimen) can be estimated from a count of the number of point intersections with a random plane of polish. Specifically:' Lv = 2NA in which NA is the expected number of intersections per unit area of the plane. As with all other measurements in quantitative metallography, the estimation of Lv is subject to a sampling error, the magnitude of which will depend on the number of observations. The analysis is usually performed by counting the number of intersections falling within a closed test figure of known area applied to a succession of different areas on the plane of polish. The test figure can be drawn directly on the screen of a projection microscope or else superimposed on the image of the structure by means of a reticule in a focusing eyepiece of an ordinary microscope. The use of micrographs is very inefficient unless, as in the present study, these are also needed for some other purpose. Consider an analysis in which n applications are made of a test figure within which the expected number of intersections is N. The expected total number of intersections counted is then given by NT = nN If (N) is the standard deviation in N for one application of the figure and if the latter is applied to non-overlapping regions so that the N's are independent in the statistical sense, then the standard deviation in Nt is given by: a(NT) = a(N)vn Eliminating n from Eqs. [2] and [3] we obtain: Thus, k will be a constant for a given specimen and test figure. From Eqs. [ I] and [4] we find As is to be expected, therefore, the fractional error in the estimation of Lv is inversely proportional to the square root of the total number of intersections counted. It is very desirable to have at least a rough estimate of k before starting an analysis, since it will then be possible to decide in advance by use of Eq. [5J how many counts should be made in order to achieve the desired accuracy in Lv. Without such information the investigator, unless lucky, will either do needless (and tedious) work or else obtain a result with too large an error. It is very easy to calculate k for the limiting case of N — 0, i.e., when the test figure is vanishingly small. In this case there is a negligible probability of two or more intersections falling within the figure. There are therefore only two possible outcomes: a count of one with a probability of, say, p and a zero count with a probability of (I-p). Thus and Therefore: We might expect k to depend on N and therefore on the size of the test figure. Such a dependence was observed2 in the analogous case involving the estimation of grain-boundary area per unit volume by a count of the number of intersections of a test circle with traces of the boundaries on the plane of polish. In this case the theoretical value of k at the limit N — 0 was 1.41. It was also predicted that k would display an initial sharp decrease with increasing N. Experimentally, k was observed to decrease to a value of 0.62 at N - 6 and thereafter remain approximately constant. Furthermore, the value of k for N > 6 was found to be insensitive to the form of the structure provided no pronounced anisotropy or grain-size variation was present. In order to determinewhether k would exhibit a similar dependence on N in the estimation of grain-

Jan 1, 1967

By J. N. Ong, J. P. Ratledge, J. H. Boyce

SINCE German operators opened the Tsumeb mine in the early 1900's, continuous operation has been interrupted only by enforced shutdowns during two world wars and the depression of the 1930's. Original metallurgical practice was blast furnace smelting. This was applicable only to low zinc ore, leaving large tonnages of high zinc ore to be stockpiled on the surface. A gravity concentrator using tables, buddles, and jigs operated for several years, but differential flotation of the ore did not get beyond the experimental stage. When the property was put up for sale by the South African Custodian of Enemy Property there was an estimated 434,000 tons of ore on surface dumps. The dump material, assaying 4.48 pct Cu, 15.8 pct Pb, and 10.9 pct Zn, had become highly oxidized during a stay of many years on the surface. But these dump ores had to be used in evaluating possible metallurgy because the shaft became flooded after the 1940 shutdown and underground ore was unavailable. Many companies examined Tsumeb but quickly lost enthusiasm because of the formidable metallurgical problems presented by the dump ore. However, on the basis of extensive test work, the present company decided that differential flotation would be successful and purchased the property after competitive bidding. Geology and Mineral Association is Complex The Tsumeb mine lies near the northern boundary of South West Africa at an altitude of 4200 ft. The village of Tsumeb is 335 air miles northeast of Wal-vis Bay, territorial port of entry. The orebody is a hydrothermal replacement deposit associated with an irregular intrusion of aplite cutting folded pre-Cambrian dolomite beds. In plan the deposit is a lens of 250x600 ft maximum dimensions. In section the orebody dips 55" south from the surface to 2000 ft, below which there is a reversal in dip to 75" north. Mineralization is localized in the aplite and in the adjoining brecciated dolomite. In the upper levels the ore is largely confined to a single lens, but below the 1890 level massive sulphide ore forms north and south lenses that partially enclose a pipelike body of medium to low grade disseminated ore, part of which is of too poor a grade to mine. Drilling below the 24th, or bottom level, has disclosed that a high percentage of the mineralization from the 3000 to 3300-ft horizons is comprised of copper and lead oxides. The deep oxidation may be local, since it appears due to circulating waters in a major fault cutting the orebody. Tsumeb ranks as one of the highest grade base metal deposits in the world. It is geologically and mineralogically famous for 41 copper, lead, zinc, vanadium, and germanium ore minerals, but its complex mineral assemblage is not attractive to metallurgists. In addition, there is a gradual change in oxidation intensity from the upper levels to the lowest level now operating, which is the 24th. This is well illustrated by the copper minerals. In the upper levels malachite and azurite are predominant, in the intermediate levels chalcocite, and in the lower levels tennantite. Throughout the mine there are sufficient heavy metal soluble salts to activate zinc, and large amounts of depressants are required even for so-called clean sulphide ores. When the same sulphide ore is exposed to prolonged oxidation aboveground, as was the case with the dump ores, reagent requirements become fantastic. Plant Construction First staff members arrived at Tsumeb in March 1947, and by May essential services had been restored and mine unwatering began. In 2 1/2 months company employees built a temporary jig and sorting plant for treating existing dumps to provide a saleable product during high metal prices. Meanwhile, concentrator design and construction was contracted to a South African firm, with subcon-

Jan 1, 1956

By Fernando A. Buttazzoni, Jorge C. Munita

INTRODUCTION To provide a background for discussing long-range financial and operational planning in the mining industry, we would like to begin by describing the role of planning in Codelco. Having taken part in Codelco's planning process since its inception in 1976, we believe that useful conclusions may be drawn for the experience we shall relate. Although Codelco is a state-owned copper producer with an important role in the Chilean economy, and is consequently very much at the core of national economic planning, the following discussion is not related to government planning but to planning in an operationally and commercially autonomous business concern with all the characteristics of a private enterprise. The only way in which Codelco differs from private business is that its financial successes or failures have a more direct impact on the countryls ability to participate in international trade, to meet its international financial commitments and to achieve economic and social growth. Thus, what follows is a presentation of the conceptual features of the planning process at Codelco and a description of the current state of planning in the company. It is understood that certain conceptual components are basic to any formal strategic planning process, and that the components of Codelco's planning process are therefore generally applicable in similar companies. First, the mission and scope of operation of the company must be defined, and goals must be set to achieve leadership in the business activities in which it engages. Having set this framework, the company must constantly scrutinize those internal elements and conditions that are essential to fulfill its mission and achieve leadership. In Codelco this means considering the actions which can best serve to define future capacities, taking into account declining ore grades and determining optimal production levels; watching over the productivity and skills of its labor force, and; keeping abreast of technological developments in non-ferrous mining and processing. If the company is proficient in these three areas, it will be cost efficient and there- fore competitive. Codelco must also watch over the business environment in which it operates. The company sells concentrate, blister and fire-refined copper, wirebar, cathodes and wire rod and must study the behavior of the market to attune its product mix to the demand existing for these various commodities in the international market and the copper consuming industries in general. By examining the internal and external environment in which the company conducts its production and commercial operations, it is able to diagnose its strengths and weaknesses, to identify the hazards it must overcome to stay ahead in the copper trade, and to take full advantage of business opportunities as they arise. CHARACTERISTICS OF CODELCO-CHILE Although our subject is Codelco, readers should keep in mind that there are many other copper producing operations in Chile, all in the private sector, and many valuable deposits that may be exploited in the future. Codelco is the only public sector copper producer, although there is one other state enterprise that operates smelting and refining facilities principally to serve a large number of very small producers of copper concentrate. In the mid-19801s, Codelco is the largest copper mining company of the world and the largest producer and exporter of copper with yearly sales totalling close to US$ 1.8 billion in 1983. Moreover, it is a highly profitable copper company at a time when the world copper industry as a whole has reported losses for several years. Codelco-Chile is a fairly new organization. The history of the four mining operations it manages is much longer: El Teniente was opened in 1912, Chuquicamata in 1915, Salavador in 1959 -- with installations of the old Potrerillos mine dating from 1927 -- and Andina in 1970. Having had separate owners, the management systems of the

Jan 1, 1985

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson' measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans' and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner's data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

By E. H. Lee, F. J. Fayers

Problems in reservoir analysis can usually he cupressed in terms of a system of nonlinear partial difjerential equations. A rnethod for .setting physically reasonable boundary conditions for these systerrls by ayplication of the theory of characteristics is discussed. A short description i.c. given of the technique for finding chnmcteristics of general first order and second orrler equations. Specific examples are quoted jrorn eqrrations occurring in theoretical reservoir studies. The princip1e. ossocicred wit11 the use of chnracteristic to set physically realistic boundary conditions me developed, and thr method is discussed in terms of boundary condition for the noncupillary, compressible, two-phase flow problen: jor the cupillary, ir~cowlpressible, two-phase flow problems for the tlrtergent flooding prohlenl; as for the compressible. noncapillary, two-phase flow pro11letn. INTRODUCTION In most problcms in reservoir analysis the physical situation is described by a system of nonlinear partial differential equations. The general solution to the set of equations usually comprises a wide range of functions ancl a particular solution is normally selectetl by applying suitable boundary conditions to the problem. In some cases it is clear from the physical situation what form the boundary conditions should take, but it is usually desirable to have an independent mathematical check of the suitability of the chosen conditions. From the mathematical standpoint, a system of partial differential equations with boundary conditions is said to be properly set if the combination determines a unique solution which is continuously dependent on the equation and the boundary conditions. Such a solution is sometimes termed "reasonable". In investigating the properties of the mathematical representation, it is useful to determine the structure of the system by the application of the theory of characteristics. This theory determines in the space of the independent variables, lines or surfaces which play a special role in thc system's behavior. The characteristics determine the possibility and nature of the propagation of discontinuities in the derivatives of the dependent variables. Along the characteristics certain differential relations hold which for some problems allow a so- lution to be obtained analytically. In the case of hyperbolic equations the characteristics can bc used as 3 basis for a numerical solution. If a complicated nonlinear system is to be solved, a study of behavior of the characteristics will indicate what boundary conditions should be chosen. By using the method of characteristics, several advances have rccently been made in solving reservoir engineering problems. Sheldon, Zondek and Cardwell' have discussed how the the method may be used grap-phically to solve the incompressible two-phase displaccmerit problem when the gravity term is included in the equations. Fayers and Perrine' have applied the method to study the equations representing detergent flooding. When compressibility and solution-gas effects are introduced into the two-phase flow problem, the equations and their characteristics become more complicated. It will be seen that in this problem the characteristics are useful for indicating a reasonable set of boundary conditions but cannot readily be used to compute a numerical solution. This problem has been solved on the IBM 701 using normal finite difference methods hy West, Garvin and Sheldon." The material to be prcscntcd in this report is divided into three sections. The first discusses the determination of the characteristics of first and second order partial differential equations; the second describes the selection of suitable boundary conditions by the application of the principle that the future cannot affect the past; the third discusses the use of characteristics for setting the boundary conditions of the two-phase solution-gas flow problem. A useful introduction to the method of characteristics has been given by Hildebrand.' A summary of the method will be given in this section of the paper. The First Order Equation The quasi-linear equation of first order is It is linear in the partial derivations of z. The properly linear equation has the form The characteristics of are curves along which the

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.'8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

Electrocarbonization of coal will produce cheap fuel for electric power plants. The complete electrification of industry and domestic power consumption of gas generated as fuel in situ is a worthwhile goal for the coal industry. Production of synthetic oils, gasoline, and coal chemicals from coal gas will create additional new markets for the coal industry. RANKING high in the nation's wealth of natural resources, readily available liquid and gaseous hydrocarbons are nevertheless falling steadily in supply, while industrial requirements for hydrocarbon compounds are greater today than during the peak period of World War 11. Theoretically, several processes will increase the future supply of liquid and gaseous fuels, but the practical application of these methods depends on two controlling factors: 1—that enough carbon-bearing material be available to warrant industrial exploitation, and 2—that the given process be physically, chemically, and economically applicable. With regard to the first factor, the Western Hemisphere is fortunately well supplied, see Table I. Table I not only shows the extensive occurrence of many fuel sources, but also the wide discrepancy among quantities of fuel substances in various materials. Great quantities of potentially available fuel have not been recovered. Many coal seams and other hydrocarbon-bearing deposits are so situated that production is uneconomical by present-day mining or oilwell pumping methods, and even in many exploitable deposits where the most efficient production methods are used a large proportion of material is never recovered. Industrial production of hydrocarbon liquids and gases must be better balanced, and processes must be developed which will convert coals, oil sand, and oil shales into fabricated commodities. Among the techniques employed by scientists and engineers to secure fuel masses not economically available at present are several processes of underground gasification. These are all concerned with converting raw materials into gaseous products by thermal treatment of source substances while they are still in the ground and therefore require that a subsurface heat (fire) zone be induced to affect pervasively the buried raw fuel deposit. This is possible only where sufficiently high temperature exists and where the fuel material is satisfactorily opened or channelized. Also, to compete successfully with common mining or oilfield practices, a given method must be controllable and must not involve greater operational expense than regular methods. Preferably, it should be less expensive. Since the close of World War 11, England has continued field studies of underground gasification methods. Experiments have also been conducted in Sweden, Estonia, France, Belgium, Italy, and Germany. The U. S. Government has sponsored field studies at Gorgas, Ala., and because gasification in situ is vitally important to establishment of the nation's fuel resources, the mining engineering department at the Missouri School of Mines has been actively interested in developing the process of underground electrocarbonization. Research was conceived by Erich Sarapuu, and preliminary experiments in treating bituminous coal were begun at the school in September 1947. The work consisted of laboratory experimentation until June 1948, at which time, through a cooperative agreement with the Sinclair Coal Co. of Missouri, pilot plant studies were instituted at the Tiger mine of the Hume-Sinclair Coal Co. near Hume, Mo., to test the encouraging laboratory findings. This comprehensive field program was pursued continuously until the beginning of 1952."'" The broad term underground electrocarbonization describes a unique gasification process that releases by electricity the desired economic constituents from a raw carbon-bearing material, converting the substance of such deposits into deliverable form and greatly reducing the cost-of-mining factor. Underground electrocarbonization is not subject to the major limitations of many other underground gasifi-

Jan 1, 1955

By K. E. Gray, M. S. Seth

Equations of elasticity for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure were formulated. Using an analogy between thermal and porous body stresses, it was shown that the solution for a transversely isotropic porous body may be obtained by incorporating body forces and the stresses due to a boundary load into the corresponding solution for the thermal stress problem. Equations of elasticity ad the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant pressure or a constant rate of flow is maintained at the wellbore. The vertical and tangential displacements are zero from the conditions of the problem. A numerical analysis was made of the solutions obtained by using a digital computer to determine the relative influence of each system variable. Considering rock as a porous body with internal fluid pressure generally gives results significantly different than considering the rock to be nonporous; the directional character of rocks leads to significant differences as compared to results based upon the common assumption of isotropy. Stress gradients are high near the wellbore but die out away from the well. Radial stresses are compressive or neutral, whereas tangential stresses are tensile, neutral or compressive, depending upon the boundary conditions and physical properties of the system Vertical stresses are compressive for an unbounded system. For constant wellbore injection rate, the vertical stress is proportional to the rate of fluid injection and decreases with time, whereas the radial and tangential stresses increase with time. At a given location, the radial displacement generally is very dependent upon time. INTRODUCTION A realistic appraisal of the state of stress in subsurface rock formations would be of considerable interest and use to the petroleum industry. For example, knowing the state of stress in proximity to a wellbore would be of fundamental importance in designing a fracturing operation or, more important, of clearly understanding the conditions necessary to produce rock failure of desired dimensions and geometry. Understanding conditions necessary for rock failure at the wellbore would also be of utility in a preventive sense. For example, borehole stability is an important consideration for many rock formations, and knowledge of the stress state at and near the wellbore under conditions of substantial pressure gradient due to fluid flow would be of great value. When fluid flows through a porous body which is initially at some uniform stress level, the following forces generate stresses at any point in the body. (1) Forces due to nonuniform pressure distribution. With increasing pressure the elements of a body are compressed. Such compression cannot proceed freely in a continuum when the pressure is not uniform throughout, and thus, stresses due to flow of fluid are set up. (2) Pore fluid pressure. This gives rise to normal stresses whose value at any point is the product of areal porosity and the fluid pressure. Although the fluid exerts uniform pressure, the stresses it creates in an anisotropic body may not be the same in all directions since the areal porosity in an anisotropic porous body is a direction-dependent quantity. This consideration leads to the concept of directional porosity. (3) Body Forces. The flow of the moving fluid imparts a force to the rock matrix, the magnitude of which depends upon the pressure

Jan 1, 1969

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

DEVELOPMENT of a chemical process for the extraction of pure metals from mill concentrates or metal scrap has progressed beyond the pilot plant stage and may prove an important adjunct to present smelting and refining methods if initial commercial operations prove economically successful. Developed by the Chemical Construction Corp., the new process involves the treatment of oxide and sulphide ore concentrates by chemical methods, instead of the usual smelting and refining techniques. Several of the many applications are now scheduled for commercial use. Refiners using the new process will prepare ore concentrates by standard flotation methods, introduce the concentrate as a slurry into an autoclave along with water and an acid or ammonia. From the resulting leach solution, recovery of individual metals is made by use of suitable reducing agents. By varying conditions during treatment, different metals in the ore are produced separately as pure powders, which may be pressed into forms ready to market, or in the case of copper, extruded as rods or pipe. The reagents are generally recovered. By manipulating the variables during reduction, selective separation of nickel, and/or cobalt, and/or copper can be made simultaneously. The separation is a continuous operation. Low metal prices are not immediately in view because of the tremendous demand at this time. However, reduced metallurgical treatment costs will allow economical mining of orebodies with lower metal content, permitting increased production to meet demand. Although the practical horizon for use of the new process appears to be limitless, one factor may enter into its employment. Just how low grade a concentrate can be economically used is unknown. In addition, for present practical considerations, only metal below zinc in the electromotive series may be processed. Each commercial application requires specific technique adaptation and pilot-plant data for engineering design. A nickel-cobalt-copper process has been researched and piloted in collaboration with Sherritt Gordon Mines, Ltd., for the firm's Lynn Lake properties. In addition, processes were tailored for cobalt concentrates of Howe Sound Mining Co., and National Lead Co., in view of the urgent need for this specific metal. Major General William N. Porter, president of Chemical Construction, says of the new process, "piloting experience has shown that production cost, from ore concentrates to pure metals should be considerably below current costs." Other savings may be realized by cutting transportation and personnel costs, and by reducing the time lag between mining and pure metal from months to a matter of hours. First commercial use of the process will start sometime this summer. Chemico is slated to finish building a $2.5 million cobalt refinery for Howe Sound Mining near Salt Lake City. The plant is expected to raise world cobalt production by 40 pct. The plant will process 35 tons of 20 pct cobalt concentrates from Howe Sound's Blackbird mine near Cobalt, Idaho, daily. Yearly production is expected to reach 2000 tons of pure metal, about one half of U. S. consumption in 1950. Steps in the Howe Sound application of the process are: 1. Acid oxidation leach. 2. Filtration (residues thrown away are insoluble compounds-gangue, iron, arsenic). 3. Cementation (for Cu removal because Cu content is too low for recovery). 4. Reduction from ammoniacal solution. 5. Separation of Co and Ni as mixed metals (95 pct Co and 5 pct Ni). 6. Recovery of ammonium sulphate. Under construction at the Fredericktown, Mo., mine of National Lead is a $5 million refinery sched- [ ]

Jan 1, 1952

By N. Pessall, A. D. McQuillan

The phase relalionsllips in an isothernzal section of the Ti-Zr-H system at 750°Chave been investigated by measurement of hydrogen equilibrium pressures. The resulting diagram indicates that the hydride phase has an anomalously wide range of homogencity extending from 66.6 to 30 at. pct H in alloys containing about 15 al. pet Zr. Measurement of the heat of solution of hydrogen as a function of alloy composition in ß-phase alloys indicates no anomalous behavior in the region of 15 at. pet Zr, and suggests that the extensive range of homogeneity in the hydride phase at about this composition must he attributed to an enhanced stability of the, hydride phase. THE manner in which titanium and zirconium react with hydrogen and the constitutional diagrams of the two metal-hydrogen systems are qualitatively very similar,'-6 as can be seen from Fig. 1 which shows the constitutional diagrams of the two systems. Quantitatively, however, there are some differences. For example, the exothermic heat of solution of hydrogen in ß titanium is smaller than that in ß zirconium, and consequently the equilibrium hydrogen pressure of a Ti-H alloy is higher than a Zr-H alloy at the same temperature and hydrogen concentration. Other differences manifest themselves in the hydride phases which exist at high hydrogen concentrations. In the Ti-H system, above room temperature, there exists only a single hydride phase in which the metal atoms are arranged on a fee lattice, but in the zirconium system there are two hydrides, and whereas the hydride of lower hydrogen concentration has a fee structure, the higher hydride has a face-centered tetragonal structure. The tetragonal hydride retains its stability up to temperatures in excess of 450oC.7 From the foregoing, it would be expected that the constitutional diagram of the ternary Ti-Zr-H system would have a very simple form, especially as titanium and zirconium are completely miscible in both the a and ß forms.8 The present work, which consists of a study of an isothermal section of the ternary system, was carried out in order to check the assumption frequently made that the electronic structure of the two metals and the mechanism by which hydrogen is held in solution in the metals is the same for each. Although this proved largely to be true, certain inter esting and unexpected features of the ternary system emerged which must be explained before we can really say that the reactions of titanium and zirconium with hydrogen are fully understood. EXPERIMENTAL PROCEDURE The most convenient method of studying hydrogen-metal systems is by the measurement of the hydrogen pressure in equilibrium with the hydrogen dissolved in the metal as a function of hydrogen concentration and temperature. In binary systems, the results are easily interpreted in terms of alloy constitution, since two-phase regions can be recognized by the fact that the hydrogen pressure at constant temperature does not vary with the hydrogen concentration in the alloy when it is in the two-phase condition. This criterion does not apply in ternary systems, but there is usually a marked change of slope in the isothermal pressure-composition curves when a phase boundary is crossed, and with care, and a knowledge of the limiting binary systems, the phase structure of the alloys can usually be deduced. In the

Jan 1, 1962