Search Documents

By I. Fatt, D. N. Saraf

A method is described for measuring two- and three-phase relative permeabilities in sandstones or sand packs using a nuclear magnetic resonance (NMR) technique to determine fluid saturations. Two- and three-phase relative permeabilities have been determined on Boise sandstone using the NMR technique of saturation measurement. Three-phase relative permeability to water was found to depend only on the water saturation, whereas three-phase permeability to oil depended on both the water and oil saturations. Relative permeability to gas in three-phase flow was found to depend only on the total liquid saturation. INTRODUCTION Three-phase relative permeabilities are extremely useful in calculating field performance for reservoirs being produced by simultaneous water and gas drives. Three-phase relative permeability data are also needed for analyzing solution gas-drive reservoirs which are partially depleted and are being produced by water drive. Some thermal recovery processes involve three-phase flow which require three-phase relative permeability data for predicting reservoir behavior. Unfortunately, three-phase relative permeability measurements have rarely been made. Also, because of the scarcity of three-phase data, it has not been possible to date to relate other measured rock characteristics to the relative permeabilities with a great certainty. Leverett and Lewis,l Reid2 and Snell3 have reported three-phase relative permeability data on unconsolidated sands. Leverett and Lewis used ring electrodes spaced along the length of the sand sample to measure the resistivity of the sample which was assumed to be monotonically related to brine saturation. Gas saturation was determined from pressure-volume measurements. Oil saturation was obtained by material balance on the cell containing the sand sample. This method is involved and time consuming. Another difficulty arises from the fact that the resistivity of the sand is a function not only of saturation of brine but also of the distribution and saturation history of the brine in the pore spaces. Reid2 used a gamma ray absorption technique for measuring liquid saturation. This method has the disadvantage that total liquid saturation rather than oil or brine saturation is all that can be measured and still another method is required to determine the saturations of individual components. snel13 used a neutron bombardment method which also required a separate determination of the individual component saturations. Caudle et al.4 measured three-phase relative permeability on consolidated sandstones using vacuum distillation for determining fluid saturations. Distillation after each reading makes this technique very lengthy and time consuming. Corey et a1. 5 and Naar and Wygal 6 measured three-phase relative permeability on sandstones by the capillary-pressure method. Semipermeable diaphragm assemblies were used at each end of the core specimen to keep the water phase in the core. Gravimetric methods were used to determine fluid saturations. Sarem7 recently reported an unsteady-state method for measuring three-phase relative permeability on sandstones. This method is an extension of Welge's method8 for measuring two-phase relative permeability. Although Sarem's method is simple and comparatively fast, the assumptions involved may oversimplify the problem. Sarem's assumption, that in all rocks relative permeability to each fluid will depend only on the saturation of that fluid, seems to be rather unrealistic. Neglecting capillary effects at the end of the core is also a weak assumption. Donaldson and dean9 measured three-phase relative permeability using a method similar to Sarem's.

By L. G. Jones

An approximate method of calculation is developed in this paper which allows duplication of radial unsteady-state gas flow computer results where Darcy's law applies, such as those reported by Aronofsky and Jenkins and Bruce, Peaceman, Rachford, and Rice. Moreover, the new calculation method can be used to obtain results for radial unsteady-state gas flow obeying the quadratic flow law proposed by Duwez and Green. Means are discussed for predicting well behavior at single or superimposed flow rates in finite or infinite reservoirs, determining reservoir rock properties from well-test data, reproducing and interpreting back-pressure test data, and determining the radial extent and reserves of gas reservoirs from well-test data. Example calculations are presented for gas flow following both Darcy's law and the quadratic flow law. INTRODUCTION Since the publishing of U. S. Bureau of Mines Monograph 7,1 most gas-well testing methods have been based on the equation q = y (pl2 - pw2)a, where q = production rate, pl and pw, are formation pressure and sandface pressure, respectively, and y and a are constants to be obtained from test data. These methods, used for predicting both deliverability and "open-flow" capacity of gas wells, have been useful and accurate in many cases but unsatisfactory in others. Even at best, however, they do not supply information about the formation or lead to an understanding of nonsteady-state gas flow in porous media. Many theoretically based studies2-4 of gas flow obeying Darcy's law have been made.' Since the partial differential equations which result from combining Darcy's flow law with the continuity equation are nonlinear, most of the published research consists of either numerical solutions or analytical solutions for linear approximating equations. Such solutions have been of limited value in field work due to their unhandy form and their failure to correlate most field data. There is evidence5,6 which indicates that Darcy's law is inadequate to describe gas flow at some flow rates of practical interest. A quadratic flow law: which reduces to Darcy's law at low rates, is more successful in accounting for experimentally observed behavior. This flow law has been applied successfully to a few hypothetical reservoir cases in work which has recently been published.10 However, these numerical solutions of the equations involved have been successful only on a special analog computer. Routine applications to field cases would be awkward and have not been attempted. The present paper describes an approximate method for computing nonsteady-state gas flow solutions which has been completely successful in predicting the results for both Darcy flow and quadratic flow obtained by elaborate numerical methods. The new calculation method allows determination of the observable variables in gas-well testing at constant rates. It is similar to the scheme of using a succession of steady states suggested by Muskat7 in that it makes use of steady-state and material-balance equations. It also is similar to the work of Aronofsky and Jenkins2 in that the new method includes Aronofsky and Jenkins' stabilized flow equation as a special case. It improves upon both of these calculation schemes in that it accurately describes all portions of reservoir history and suggests means of determining reservoir rock properties from well-test data. This paper deals only with production from a reservoir, in which case the rate is defined as being negative. The reservoir studied here is a homogeneous, disk-shaped porous body of uniform thickness, with all boundaries sealed except the inner radial boundary of the well.

By O. P. Quist, S. H. Carpenter

The internal friction of single-crystal LiF has been investigated as a function of crystal orientation, while simultaneously applying a static compressive load. Three different crystal orientations were used, these being samples with the (100), (110), and (111) directions along the sample length. Results show the internal friction measured to be similar in appearance but different in magnitude for the (100) and (110) samples. With both orientations, application of a static stress caused an increase in the amplitude-independent damping, which recovered with time. The amplitude-dependent damping was found to first decrease with load up to the yield stress and then increase rapidly. Samples of the (111) orientation were found to have no measurable internal friction even when loaded up to 3.0 kg per sq mm. These results are discussed in terms of current theories of internal friction in ionic crystals. This paper presents the results of an investigation of the dislocation mobility and dislocation motion in high-purity single-crystal LiF at applied stress levels up to the yield stress. Internal friction measurements of the dislocation damping while simultaneously applying a static compressive load was the experimental technique used. LiF crystals much prefer to slip on the (110) set of slip planes. However, with a suitable stress distribution they can be forced to slip on the {100} set of slip planes.' For both sets of slip planes the slip direction is the same, namely (110). The object of this investigation was to try and learn more about the dynamical properties of dislocations on the different slip systems in LiF crystals. EXPERIMENTAL PROCEDURE Dislocation damping was measured, in terms of the log decrement, using a five-component marx2 composite piezoelectric oscillator. The apparatus used allows one to measure the dislocation damping while simultaneously applying a static compressive load on the sample. A schematic of the apparatus used is shown in Fig. 1 and a complete discussion of its construction and operation is given elsewhere.3 All measurements were made at room temperature with a longitudinal resonant frequency of approximately 50 kc per sec. Damping measurements were made using longitudinal vibrations with strain amplitudes from up to 10. Static loads up to 3.0 kg per sq mm were applied to the sample while the damping was being measured. Samples used in this investigation were high-purity single crystals of LiF purchased from the Harshaw Chemical Co. All samples were approximately of an in. square and were hand-ground in length to one-half wavelength to match the resonant frequency of the driver and gage quartz crystals. Samples of three different crystallographic orientations were used, namely, crystals with the (loo), (110), and (111) direction parallel to their length. The magnitude of the damping is a direct measure of the area on the slip planes swept out by dislocations during a complete oscillatory cycle. With a sample of the (100) orientation the maximum applied shear stress, due to longitudinal vibrations, is on the (110) slip planes with zero shear stress on the (100) slip planes. Thus, damping measured from a (100) sample is due entirely to dislocation motion taking place on the (110) set of slip planes. Similarly, for a sample of the (111) orientation there is zero shear stress on the (110) set of slip planes and the damping measured from a sample of this orientation is due entirely to dislocation motion on the (100) set of slip planes. Samples of the (110) orientation will have a component of shear stress on both sets of slip planes and

Jan 1, 1969

By D. H. Thompson, A. W. Tracy

E. A. ANDERSON*—At the outset, I note that you are using a humid atmosphere containing ammonia but that you make no reference to the variable of carbon dioxide content. Edmunds in his work in this laboratory found very marked effects on the rate of failure due to variations in carbon dioxide in the environment. This point is, of course, strongly related to the overall corrosion rate problem since the role of the carbon dioxide seems to be to permit the formation of hygrogroscopic salts which give a controlled moisture film on the specimen surface, which in turn seems to support the intergranular penetration more consistently than would otherwise occur. (2) Your results with various copper binary systems are very striking. It is curious, however, that the time-to-failure minima all occur at percentages of the alloying element which are considerably below the solubility limits as given in the conventional equilibrium diagrams. If your theory regarding the presence of these impurities in some concentration in the grain boundaries is correct, then either the existing diagrams are not accurate in the room temperature region, or there is a difference in solubility in the grain boundaries as compared -with the grains. A study along these lines might be very revealing. (3) The undesirable effect of silicon in copper calls to mind our own observations on the influence of silicon on the stress corrosion cracking resistance of alpha brass. In this case, silicon was found to have a very marked beneficial effect, particularly when a heat treatment capable of producing a grain boundary constituent was used. I should appreciate it if in the discussion of your paper this point should arise, you would attempt to clarify the difference between the copper-silicon binaries and the copper-zinc-sili-con ternary alloys. D. H. THOMPSON and A. W. TRACY (authors' reply)—(1) We have no data on the constancy of the carbon dioxide content of the air used for the test atmosphere but have believed that the normal carbon dioxide content of the air was as constant as could be obtained by using Edmunds' method of removing carbon dioxide from the air and then adding a measured quantity. In any event, the test atmosphere was the same for all specimens in a test run. We agree with Mr. Anderson that the carbon dioxide content is important in the formation of a hygroscopic film on specimens. (2) We can imagine that there could be a concentration of solute atoms at the grain boundaries which would be so small that present methods would not detect it even if it exceeded the solubility limit of the alloy. There could be somewhat greater solubility at the grain boundaries for an interstitial solute. There is a possibility that phosphorus dissolves in this way but we believe that none of the other solutes studied does. In our present studies we hope to find out something about conditions at the grain boundaries of some of the systems mentioned in the paper. (3) Mr. Anderson points out that silicon brass, which has had a high temperature heat treatment followed by a quench. is highly resistant to stress-corrosion cracking. Although the test conditions used by Anderson* et al were different from our test conditions, it is noted that the silicon brasses which had not had the special heat treatment were less resistant to stress-corrosion cracking than copper containing approximately equal amounts of silicon. G. R. GOHN†—Nonferrous metallurgists and particularly, materials engineers, have been accustomed to thinking

Jan 1, 1950

By T. K. Prentice

ABSTRACTED AND REVIEWED BY E. W. DAVIS,* MEMBER A.I.M.E. THE January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. PRACTICAL BALL-MILL TESTS IN A CYLINDRICAL MILL Part I of the paper begins with a discussion of the methods used for the manufacture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4 ¼ - in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 2 5/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3 ½ in., 3 in. or 2 ½ in. balls by means of three Drop and two Beché hammers, but the greater number, whilst still at about 1,000 ºC., pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 2 5/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: ….. The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13 ½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1944

By Strathmore R. B. Cooke, Marcus Digre

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,12'3 and the method has been applied to the concentration of various iron ores4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Advantages are that a direct value for the amount of calcium adsorbed is obtained, and introduction of a collector which may affect the adsorption is avoided. The difficulty is to determine the extremely small differences in the calcium concentrations before and after the abstraction. The second method was to determine the activation of the quartz by observing the contact angle obtained on pressing an air bubble against the polished surface of a piece of quartz immersed in a solution of calcium chloride, sodium hydroxide, and sodium oleate. This is the well-known "contact angle" method. The third method was to determine those conditions under which an air bubble will pick up quartz particles immersed in a solution of the desired reagents. Disadvantages common to the sec- ond and third methods are that introduction of a collector is necessary to obtain bubble contact with the mineral; very small quantities of contaminant can give erroneous results; and no information is obtainable concerning the amount of calcium adsorbed. Advantages are that tedious analyses, which at best give approximate results, are avoided, and the conditions, especially for the third method, closely simulate those of actual flotation. Although the most consistent results were obtained with the third method, this paper describes the techniques used and the results obtained from each of the three methods. Distilled water and analytical grade reagents were used throughout except where otherwise stated. Between tests all glass articles were cleaned with a chromic-sulphuric acid mixture and sodium hydroxide. Abstraction Method The raw material for the tests was Ottawa sand sized between 14 and 28 mesh. Batches of 500 g of this sand were dry ground for 1 hr in an Abbe porcelain mill with 2700 g of quartz pebbles. The batches were split down to samples weighing approximately 30 g, and the weight of each sample was adjusted to exactly this value.

Jan 1, 1950

By G. R. Gray, T. S. Chapman, J. L. Foster

THE wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as tragacanth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. INTRODUCTION It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.1-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-11 The wall-building properties of fresh-water muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods generally used in controlling filtration of fresh-water muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. LABORATORY INVESTIGATIONS Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester' at a pressure of 10o lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 c.c. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1941

By J. A. Thompson, M. A. Mayers

IN recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.1-14 Only in Russell's method11 and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce-the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼ in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C. consisting of two annuli of 0.011-in. (0.28-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By R. H. Maes, R. E. de Strycker, J. J. Jacobs

A simple method, based upow density measurements, has been perfected in order to determine the critical temperature of liquid miscibility gaps. Applied to the Pb-Cu system, it yielded a value of 980"C for the critical tempevature of the miscibility gap in this system. In the Pb-Cu-As system, the immiscibility between lead and coppev evolves towards a miscibility gap be-tween lead and copper arsenides; the liquation temperatures were determined joy different avsenic contents and values up to 1065°C were found. Combining these results with those given by the clzemical analysis of liquid samples taken at dqj.event temperatures, it has been possible to make a cowzplete determination of the liquid miscibility gap in this ternary system. In the Pb-Cu-Fe-As system, a ternary miscibility gap has been discovered; for some compositions, the molten and slowly cooled alloys separated into three layers: an Fe-As alloy, a Cu-As alloy, and a lead-rich layer. ThE Pb-Cu-Fe-As system is of interest for the study of the behavior of speiss or arsenical alloys in the lead blast furnace. The speisses produced in lead metallurgy generally have complex compositions, but they may be considered, in a simplified way, as a mixture of copper, iron, nickel, and cobalt arsenides; there is often an excess of metallic constituants, and lead is also present. Speisses liquate from lead at various temperatures according to their composition; according to industrial experience, iron speisses are already distinctly separated from lead bullion at temperatures of the order of 1100°C, whereas copper speisses only begin to liquate from lead at much lower temperatures, near their solidification points, which were never accurately determined until now. Besides these considerations of practical interest, the present study is of importance for the knowledge of liquid miscibility gaps. Particularly the data of the literature about critical temperatures of liquation are incomplete and present sometimes considerable disparities; a method has been perfected in the present work to determine these temperatures with accuracy. MISCIBILITY GAP OF THE LEAD-COPPER SYSTEM Review of Literature. The generally admitted outline of the Pb-Cu equilibrium diagram is shown by Fig. 1. This figure, with its numerical indications, is taken from the review of Hansen and ~nderko;' compositions are given in weight percent, as will be the case in the remainder of this paper. Between 36 and 87 pct Pb, Pb-Cu alloys separate into two layers, in the liquid state. The critical temperature of liquation has been much disputed in earlier studies, where values up to 1500°C were claimed; but a reliable study of ~ohnen,' based upon differential thermal analysis, gave a value of 990°C; this rather low value was verified by a recent study of Schiirmann and Kaune? based upon thermodynamical properties of the Pb-Cu alloys, which predicted a value of 1002°C. Liquid miscibility gaps were also studied by means of chemical analyses. Satisfactory results were generally obtained with the method consisting in taking samples of the two liquid layers in equilibrium and submitting them to chemical analysis; however, this method becomes delicate near the critical temperature. With this technique, Friedrich and waehlerts ob-

Jan 1, 1968

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By H. T. Clark

Within the last twenty years at least three sets of lattice constants for the room temperature (alpha, hexagonal close packed) phase of titanium have been reported in the literature. These values, summarized in Table 1, differ one from another by amounts far greater than can be explained on the basis of inaccuracies in parameter measurements. This paper presents new values determined for high purity titanium. It also details the effect of two elements, oxygen and nitrogen, on these parameters and shows that two of the previously reported values are probably in error because of the presence of one or both of these elements in the material used for examination. Preparation of Samples The titanium+ used for this study was prepared by the thermal decomposition of titanium tetraiodide7 on a hot titanium filament. This titanium rod was prepared for X ray examination by melting about 10 g in purified argon in an electric arc furnace on a cold hearth. This cast button was cold rolled to 0.040 in. thick sheet, cleaned, annealed in vacuum at 1000°C and cold rolled to 0.020 in. thickness. About 0.003 in. of surface material was then removed by hand grinding on papers to remove any contamination caused by the rolls and the sample was bent to the radius of the focusing camera. The sample was then vacuum annealed at 600°C, a temperature just high enough to cause recrystallization, producing a fine grained structure. Such a structure is essential in sheet specimens prepared for focusing cameras in order to have a sufficient quantity of grains to develop continuous diffraction lines. The use of sheet specimens rather than powder samples appears to be essential for the X ray examination of titanium. This is because of titanium's exceptionally high gettering power and its rapid absorption of adsorbed gases, water -vapor, and the like at annealing temperatures. While the effect of this contamination may be neglected for sheet specimens, its effect on 200-300 mesh powder is appreciable. Titanium alloys of oxygen and nitrogen were prepared by a technique simi- lar to that described above except that the required amount of the highest purity titanium oxide or nitride available was added prior to melting in the arc furnace. These materials were added by placing them in holes drilled in the titanium. A small weight loss invariably occurs during the melting of these oxygen and nitrogen alloys. This is believed to be due entirely to the loss of some of the powdered compound in the blast of the electric arc, an assumption which is justified on the basis that there is no weight loss during the melting of titanium metal and that wet analyses for nitrogen on representative samples have checked with the calculated analyses when it was assumed that the entire loss during melting was due to the loss of titanium nitride powder. These alloy buttons were reduced to sheet in the same manner as used for the unalloyed titanium. Experimental Procedure A North American Phillips 12 cm diam symmetrical precision focusing vacuum camera and copper radiation

Jan 1, 1950

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By C. E. Birchenall, W. Batz, H. W. Mean

AT temperatures between 1095' and 1347ºC, 13 runs have been made on the diffusion of silicon in iron. In two of the runs the couple compositions were entirely within the loop of the Fe-Si system; the base alloys contained 0.0 and 1.0 wt pct Si. The other runs in which the couples consisted of a 2.3 wt pct Si alloy welded to a 3.7 pct Si alloy were a phase throughout. The alloys were made by melting electrolytic iron and commercially pure silicon. Trace impurities were not determined. The butt welded couples were diffused in an inert atmosphere of argon or hydrogen. After cooling, cuts of two mils or greater thickness were machined parallel to the weld interface. The chips were analyzed for silicon. When the concentration and distance data were examined on the conventional probability plot,' no marked variation of the diffusion coefficient with concentration was indicated over the narrow composition ranges employed. Therefore, a single diffusion coefficient is recorded for each run in Table I. The temperatures and atmospheres of the diffusion anneal are listed along with the compositions of the base alloys. For a iron the silicon diffusion coefficient is given by the equation: D = 0.44 e-48,000/RT where R is the gas Constant and T, the absolute temperature. However, since the scatter in the data is fairly large, the activation energy may be in error by as much as 6000 cal per g-atom. The two ? iron points do not permit estimation of the activation energy with any reasonable certainty. They do indicate that the coefficients reported by Smithells2 and Jost,3 based on the work of Fry,4 are much too high. Although very dilute solutions in iron of manganese,5 nickel,8 cobalt,7 and molybdenum8 give dif- fusion coefficients quite close to those obtained for self-diffusion in iron, the silicon values are considerably higher, though of the same order of magnitude. This seems to be consistent with the fact that the silicon atom is the only one of those listed here which is appreciably smaller than iron. The authors are grateful to the Office of Naval Research for their support of this work under Contract N6ori-47, Task order IV, Project NR 031-184, to J. K. Stanley and the Westinghouse Research Laboratories for the silicon alloys used, to several steel companies for the silicon analyses, and to C. Wells, of the Metals Research Laboratory, Carnegie Institute of Technology, for numerous suggestions during the course of the work. References 'C. Wells: Atom Movements (1951) Chapter 2. A.S.M. 2C. J. Smithells: Metals Reference Book (1949) p. 405. Interscience. Pub. Co. 3W. Jost: Diffusion (1952) p. 223. Academic Press. 4 A. Fry: Stahl und Eisen (1923) 43, p. 1039. T. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 315. "C. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 329. 7M. F. Hawkes and R. F. Mehl: Trans. AIME (1947) 172, p. 467; Metals Technology (August 1947). .J. L. Ham: Trans. A.S.M. (1945) 35, p. 331.

Jan 1, 1953

By A. K. Snelgrove

This symposium is designed to marshal a state-of-the-art account of approaches and solutions to problems arising out of waterlogging and salinization in the world's largest irrigation system which was dismembered by legal beheading of the Eastern Rivers under the lndus Waters Treaty of 1960. In this introduction, the geological and historical backgrounds of surface waters and groundwaters in the Indus Basin are presented with a summary of remedial measures undertaken and proposed to combat waterlogging and salinization. At a time when water-resource planning is proceeding on a continental scale, a study devoted solely to the Indus River Basin may seem to require an apologia. None is offered, however, for three major reasons: (1) Although the Indus is a single river basin, it is one of great magnitude and importance. The Indus River, which comes from Himalayan sources to form part of the great Indo-Gangetic Plain drainage system, is vital to agriculture and hydroelectric power in the thickly populated northern subcontinent of Indo-Pakistan. (2) The Indus has become a plexus of extraordinary problems since the dismemberment of the world's largest irrigation system of which it was a part. The break-up of this system occurred with the legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960. (3) Th River Basin has been the target of a Herculean effort to contain the twin encroachments of waterlogging and salinization that now threaten it with a shortage of fresh water. The British irrigation system of barrages and canal on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage. To cope with this situation, there has been a possibly unprecedented concentration of domestic and international engineering and scientific talent on the Indus and its problems (about a score of organizations by recent count). To marshal a state-of-the-art account of their approaches and solutions is the purpose of this Symposium. The coordinated effort now being made on a variety of fronts under the general supervision of West Pakistan Water and Power Authority (WAPDA) is directed toward the modification and control of interactions and relationships between geological materials — soils, water and its salt balance, and air —in what has been termed a huge "underground lake" in an alluvial basin. The problem is an intriguing one in that a highly complicated case history of river-course changes visible in the present surface must be projected downwards through Recent and Pleistocene sediments in order to decipher the environmental controls of deposition in terms of vertical and lateral variations in lithology and patterns. Such studies must be extended to compaction, deformation, and fabrics of the alluvium. Geohydrology is often defined as groundwater hydrology. As employed herein, it includes the distribution, quality, and behavior of surface and subsurface waters, including their evolution, vagaries, and geological, climatological, and botanical milieux." GEOGRAPHY The Indus (Sanskrit, Sindhu = river) rises at nearly 17,000 ft above the sea in the glaciers on the northern slopes of Kailas Parbat, Tibet. It is about 1800 miles long and has a total drainage area estimated at 372,000 sq miles. The average discharge is 196,000 cfs at mouth. Leaving the Plateau of Tibet, the river flows at a level which is miles above the sea, and in places miles below Himalayan peaks, in a structurally controlled northwestward course. Joined in this course by six tributaries and swollen by the melt waters of giant glaciers, it swirls about the base of the famous

Jan 1, 1970

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951