Search Documents

By Y. Dardel

Since the first determination of Dumas1 in 1880, many authors have tried to measure the solubility of hydrogen in solid aluminum, or at least the amount of dissolved gas in it. However, the interpretation of the results which have been obtained is still difficult. Sieverts? then Baukloh and Oesterlen,a during their gassing experiments could not determine any solubility of hydrogen in solid aluminum. On the other hand, Portevin, Chaudron and Moreq4 leaving the determination of the hydrogen solubility beyond the scope of their experiments, measured only the amount of gas that they could extract by high voltage positive ion bombardment and found up to 151 cm3 of gas per I00 g of metal. Winterhager,6 by repeated vacuum extraction during severe cold rolling, extracted up to 161 cm3 per 100 g. In both series of experiments, the extracted gas contained chiefly hydrogen with a small amount of nitrogen, carbon monoxide, carbon dioxide and methan. Later, Schmidt and von Schweinitze as well as Chaudron and Moreau7 showed the importance of the adsorbed layer of hydrogen, the extracted quantities being proportional to the surface and not to the weight of the sample, when its cleaning was not perfect. In earlier experiments, Steinhausers extracted from more massive samples nothing but a little amount (< 0. 5 cm3 per I00 g) of hydrogen, carbon monoxide and methane. Thus, according to these experiments the quantity of dissolved gas is probably very small and the effect of the surface could falsify the results of the extraction. However, owing to the care taken by Chaudron and his coworkers, it was clear that all the hydrogen extracted could not come from the superficial layer, or that the links which bound hydrogen to the surface were so strong that the usual method of cleaning could not destroy them. After the main parts of the experiments reported here had already been carried out, Eborall and Ransley9 published the results which they obtained with an analysor having an accuracy of 0.03 cm3 per I00 g, while that of the usual apparatus was only about 0.2 cm3 per I00 g. During all their experiments the adsorbed layer would have been a difficulty, for the value of the adsorbed hydrogen was approximately equal to that of the dissolved amount. Table i—Amount of Adsorbed and Dissolved Hydrogen (After Eborall and Ransley) Extraction Hz Adsorbed „ h2 dissolved Temperature Calculated Extraction OCcma 500 0.057 0.050 600 0.062 o.096 Since always keeping the same adsorbed layer is very difficult, an error in the correction for the adsorption can be made when using the apparatus of. Eborall and Ransley, as well as the earlier apparatus.

Jan 1, 1949

By G. H. Alani, H. T. Kennedy

One of the major difficulties in predicting the performance of oil reservoirs from their early pressure history lies in the uncertainty of estimating the volume of the liquid hydrocarbons contained in them. As a first step in filling this need, an equation was developed to determine the Inolal liquid volume of pure hydrocarbons over a wide range of temperature and pressure. The second step consisted of adapting the equation to apply to mixtures, with the heary hydrocarbons expressed as c The equatious are similar in form to van der Waals equation. hut the constants a and b tire considered as furnctions of temperature. In addition to the gas constant R, there are four constants characteristic of each hydro- When comptired with experimental values jound in the literal the. the average absolute deviation in the calculated molal volumes is found to be a Maximum of 0.33 per -cem for any of the pure liquid hydrocarbons studied. This maximum deviation was that found when comparing the calculated and observed values over a temperature range of 86° to 482°F and a pressure range from the bubbl-point ro 10,000 psis. The equations expressing the correlation for. mixrurrc were developed from 647 experimental measure-rilents of volume on 47 bouom-hole samples covering ; temperature range of 72" to 250°F and a pressure znge from bubble-point ro 5,000 psig. The average absotute deviation was found to he 1.6 per cent with the maximum for any measurement of 4.9 per cent. INTRODUCTION Accuratc information of the pressure-volume-temper-iiture behavior of hydrocarbon liquids is of considerable importance in the field of both applied and theoretical science and, especially, in the solution of petroleum reservoir engineering problems. These PVT relationships can be expressed graphically, in tabular form or as equations of state. Equations of state for gases have been developed based on the ratio of pressure, temperature and volume to the pressure, temperature and volume at the critical points of the hydrocarbons. These equations have been successful in yielding values fairly accurate for reservoir engineering purposes. For liquids, however, relations of this type are more complex and have not yielded useful results. The composition of reservoir liquids is normally expressed in terms of the moles of hydrocarbons C,? C,. C,. elc, per mole of mixture. The composition must include the fraction of a mixture such as C,,, which cannot be separated with reasonable time and effort into specific hydrocarbons. Although there are several equations of state having variable degrees of accuracy applicable to pure liquid hydrocarbons, none includes a means for estimating the volume of mixtures as a function of temperature. pressure and composition expressed in this manner.

By M. R. Goldick

THE Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5 1/2-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mechanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. ORE TREATED Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopyrite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (90 pct minus-200 mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1947

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows : the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize, The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt&apos;s main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4, The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute, 5. The recipient of the award shall be designated "The Hunt Medallist," This prize is administered by the Iron and Steel Committee. Awards of the medal have been made as follows 1920-Robert Woolston Hunt. 1926-Charles Lewis Kinney, Jr. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-

Jan 1, 1928

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

By Margaret Dienes, Karl L. Fetters

IT is recognized that ingot structure is important in determining the quality of finished steel. Such elements of ingot structure as the size, shape and distribution of primary crystals; the size, shape and distribution of shrinkage cavities; the degree and kind of segregation (both macro and micro); the distribution of nonmetallic impurities and gas cavities are each the result of solidification phenomena. These structural features vary with variations in ingot practice: Their control requires a knowledge of their correlation with the variables of ingot practice. The structures of full-sized commercial steel ingots have been studied extensively by the Steel Ingots Committee of the Iron and Steel Institute.1 This work has contributed much to our knowledge of ingot structure and the factors that control it. These investigations of necessity have been limited in scope because of their costliness and the great amount of time required. Studies of the structure of small steel ingots have not been very satisfactory because of the rapid rate of freezing of the ingots. Their structures are thus difficult to resolve and to interpret. Medium sizes of steel ingots in the ranges of 150 to 500 lb. do offer opportunity for study, but their cost also becomes greater and their use less expeditious. Experimental models for the study of steel-ingot structure have been made of nonferrous metals. Gathmann2 used lead-tin alloys and reported that they were satisfactory for determination of the location of the major shrinkage cavities and the "planes of weakness" resulting from the pattern of crystallization. Certain features of mold design have been illustrated by these results. Bezdenezhnihk3 has used copper and aluminum ingots similarly and has shown the effect of mold-wall thickness on the depth of columnar grains. These studies of nonferrous models have been useful, but their results have been limited because the analogy with steel ingots obviously is not a close one. Model wax ingots have also been useful in pointing out important features of mold design. Gathmann4 watched the solidification of wax ingots, through a glass-walled mold, and has reported the effects of mold type on the location of the shrinkage cavities. Segregation was simulated by using a mixture of paraffin and stearine and adding a red dye that on freezing segregated preferentially to the stearine. Brearley5 also used wax models to determine .the effects of some of the principal features of mold design. Carlsson and Hultgren6 used stearic acid to show that the columnar crystals of ingots tend to slope upward progressively from the mold wall toward the center of the ingot. As with the nonferrous ingots, the wax ingots have

Jan 1, 1943

ASDIE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows: the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. Robert W. Hunt Medal and Prize The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the subcommittee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt&apos;s main contributions to the industry have been in the improvement of production and quality of material. 3. A subcommittee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered by the Iron and Steel Division. Awards of the medal have been made as follows: 1920—Robert Woolston Hunt. 1926—Charles Lewis Kinney, Jr. 1928—John A. Mathews. 1929—Edgar Collins Bain. J. E. Johnson, Jr., Award This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-chairman

Jan 1, 1929

By Ralph Hultgren, David W. Mitchell

Magnesium alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600" to r 7o0°F.; the casting temperature, which depends upon the mold shape, is usually 200° to 300°F. lower. The process of superhcating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported1 that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results? As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted&apos; project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. Materials and Methods The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesiun used in these alloys was of both carbothermic3 and electrolytic&apos; origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200° to 1250°F., portions of approximately one pound each, were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21 † covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F. for 15 min., then . cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By R. W. Hunt

The old plan was to increase every part of a rail much in the same proportion. But each part should be in proportion to what it ha.; to do. The head should be deep in proportion to tile amount. of traffic and the lowness of the rate of interest on its cost. The body need only he strong enough to carry the head after it is well worn down, and that deperlds on the weight of the machinery, and in the case of steel has little to do with the volume of traffic, except SO far as that affects weight of machinery. Ad on most railroad systems, the same niacliinery is used on main lines with heavy traffic, and bra11ct:es with light, I suggested in 1874 that each systern adopt the same body of rail for both, and make the head deeper on the main lines, shallower on the branches. This plan was adopted on the Pennsylvania Railroad. Bandberg seems to recognize this in his patterns of 1878. E. W. HUNT, TRoy, N. Y.: Again Dr. Dudley preaents to our cousideration a series of most carefully conductetl experiments, and ~llile I fully appreciate the labor and thought this work has cost him, I must still hesitate to accept his deductiono. This paper dilliirs from the previous one in that it denls esclrieively with the wearing qualitiei. of steel rails. Dr. Dudley gives his reason for this change in the following statement: " With the improvement in maintenance of way which has characterized the Pennsylvania Railroad during the last five or six yearn, the remova1 of rails from the track from the first two of these causes (i. e., broken and crushel), has, if I am right, quite notably diminished. This certainly is true with regard to broken rails. And if, as time advances, the number of crushed rails shall diminish, both because of the continued improvement in maintenance of way before referred to, and because, owing to improved and better methods at the steel works, there are fewer crushed rails caused by physical defects in the steel, the question of the wearing capacity of steel rails obviously becomes the allimportant one." Certainly the condition of the roadhd has much to do with mils brealring, crushing, and wearing. If the Pennsylvania and other railroads have done and are doing their part, Dr. Dudley oourteously admits that the steel works have performed part of theirs. But as far as I am informed, the formulas which they have used have been and are still quite wide of the one he continues to recommend. The rails which are not breaking or crushing to so great an extent as formerly, contain higher percentages of both carbon and manganese.

Jan 1, 1881

By Henry J. Welge

Laboortory apparatus has been devised which permits study of the displacement of oil from cores by water and by gas. The cores used contained interstitial brine as well as oil. Experiments were run to determine the comparative effect of varying the properties of the fluids used. No great effect was noted on the maximum displacement achieved. This observation made it unnecessary in initial work to use fluids in their exact reservoir conditions. Consequently, the displacements were run at near-atmospheric pressure in Pyrex glass equipment, using stripped crude oils. Introduction and Theory The chief object of this work has been to determine the efficiency of gas and water as primary agents for displacing oil from reservoir rock under laboratory conditions in which capillary phenomena were predominant. To this end the maximum displacement of oil from cores has been ascertained. This maximum displacement may not be equal to the maximum displacement from a reservoir; but it will be a close approxirnation to it sometimes, and other times the laboratory information will be useful in reservoir engineering predictions. It is] believed that the laboratory experimental maximum represents the upper limit for the reservoir recovery. The experiments were carried out by obtaining cores of interest from the reservoir, and filling the pores with interstitial brine and oil with the restored state tech- nique.1 Then the oil was displaced from the core as described later, either by brine from below, or by gas from above. The former type of displacement suggests analogy to production by water drive, but not to water flooding, for reasons discussed below. The latter type of displacement is believed to simulate production by gas cap displacement. The displacements were performed by what may be termed the capillary-pressure method. The cores are placed in capillary contact with an oil-wetted membrane which has very small pores (about I micron in diameter). Pores of this size will transmit oil but Prevent the Passage of gas or water, unless the Pressures used are higher than the capillary Pressures employed in this work. Accordingly, use of the membrane makes it possible to apply a capillary pressure differential between the displacing phase and the oil in the core. AS in the displacement of brine toward that condition of oil and water distribution existing originally in the reservoir,&apos; it may not always be desirable to reduce the oil saturation in this experiment to an absolute minimum. With reservoirs having small productive closure, it is preferable to evaluate and use a displacing pressure no higher than the capillary pressure, Ap, which will ultimately become available for displacement in the reservoir. This pressure may be calculated from a knowledge of the density of the oil-in-place, do, the density of the displacing phase, dl, and Ah, the vertical distance between the section of the

Jan 1, 1949

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

Phase diagrams for the Ti-W and Ti-Ta systems were determined. The Ti-W system is characterized by a wide, two-phase region of ß plus tungsten which is derived from a peritectic reaction between the liquid and tungsten solid solutions. The ß field terminates in a eutectoid reaction between a titanium and tungsten terminal solid solution. Tantalum and ß titanium form a complete series of solid solutions. Other features of this system are the extensive a-ß field at low temperatures and an appreciable solubility of tantalum in a titanium. BOTH tungsten and tantalum were first thought to form ß-isomorphous systems with titanium as a result of early work&apos; using powder-metallurgical techniques. Later work2 on arc-melted Ti-Ta alloys, made using a commercial titanium base, showed that, in the range of 0 to 10 pct, tantalum was soluble in ß titanium and that the a solubility extended to between 2 and 5 pct Ta at 790 °C. The present investigation covered the entire alloy range in both systems and was chiefly concerned with high-purity alloys at the titanium-rich end. The constitution of titanium-rich alloys made with a commercial titanium base was reported by Holla-day, Kura, and Jackson.3, 4 As will be shown in detail later, the early prediction of a isomorphism was true for the case of the Ti-Ta system, but not for the Ti-W system. The results of this investigation will be presented first. The experimental methods used are described in the Appendix. Ti-W System The entire Ti-W phase diagram is shown in Fig. 1. Details of the titanium-rich side are shown in Fig. 2. The chief features of the system are a ß eutectoid and a high-temperature peritectic between liquid and tungsten solid solution. Melting Range: Examination of cast structures of low and medium-tungsten-content ingots showed cored ß phase as the primary constituent. Fig. 3a illustrates a typical cast structure for alloys in the range of 20 to 30 pct W. From 30 to 72 pct W, coring was very severe. Alloys containing 72 through 88 pct W, however, showed definite evidence of a peritectic reaction between the liquid and a terminal solid solution of titanium in tungsten. Fig. 3b shows the cast structure for an 80 pct W alloy. A 95 pct W alloy, shown in Fig. 4, consisted primarily of primary tungsten solid solution plus a small quantity of ß probably rejected during cooling. Incipient-melting experiments located the peritectic temperature between 1850" and 1900°C and indicated that the reacting phases are liquid containing about 25 pct W and tungsten terminal solid solution containing about 8 pct Ti. Figs. 5 and 6

Jan 1, 1954

By S. Beatty

RECENT experimental results&apos; on the superconductive properties of vanadium indicate that the magnetic behavior of the metal is greatly affected by internal strains caused by mechanical work, and particularly by oxygen and nitrogen impurities. These result in an increase in the hardness of the metal such that metallurgists&apos; have used hardness as a measure of the impurities. An increase in the impurities should also be reflected in a change of lattice parameter with increasing impurity content. The lattice parameter of vanadium prepared by the thermal decomposition of the iodide has been determined by two workers. Neuburger3 obtained a value of a, =3.0338 ± 0.0003A for the body-centered cubic lattice by means of the powder method. The work of Katelaar is referred to by van Arkel4 in which a value of a0 = 3.025 is given. Four samples were used for this investigation. Sample A, the vanadium of the highest purity in the group, was obtained by means of the thermal decomposition of vanadium diiodide and deposited on a 3 mil diam tungsten filament in the form of crystals. The second sample, labeled B, was obtained by the calcium reduction of the pentaoxide at a sufficiently high temperature to give a melt. A third sample, C, was obtained in the same manner as B but remelted in a pure argon atmosphere. The last sample, D, was prepared by the calcium reduction method and the fine powdered vanadium was then sintered by means of applied heat and pressure. Samples A, B, and C were thus essentially free of mechanical strain in their preparation. Sample D was annealed in a high vacuum at 800°C. The samples were prepared for X-ray diffraction analysis such that all additional strain by cold work or by contamination with oxygen and nitrogen was kept at a minimum. Powder obtained from filings was deemed unsuitable since this would require annealing to get rid of the cold work. A heat treatment up to 1000°C at 10-6 m pressure might still increase the impurity content by means of adsorbed oxygen from residual gas in the vacuum chamber. The most satisfactory samples were prepared for back-reflection film techniques. Samples were cut to size, etched with hydrobromic acid, and mounted in Bakelite. They were then lightly polished on 3-0 paper and lightly etched. Chemical and Hardness Analysis of Samples Spectrographic analyses were made of the four samples and indicated similar metallic impurities for the group. The major metallic impurity in each sample was iron, which was less than 0.01 pct. The sum of the other metallic impurities was approximately 0.1 pct. The carbon content was assumed low by virtue of the methods of sample preparation. The principal impurity difference between the samples was in the oxygen and nitrogen content.

Jan 1, 1953

ASIDE from the John ,Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows : the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circum- stances, both prizes may be allotted to one person provided that he is not over 10 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt&apos;s main&apos; contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered by the Iron and Steel Committee. Awards of the medal have been made as follows: 1920-Robert Woolston Hunt. 1926-Charles Lewis Kinney, Jr. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-

Jan 1, 1928

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By C. W. Merrill

The price records of seven representative mineral commodities for the 68-year period 1890 through 1957 have been compiled and analyzed for significant trends. When these records are reduced to real prices in terms of dollars of constant purchasing power or to the purchasing power of industrial wages at average rates, a substantial overall fall in prices is revealed. This downtrend contradicts the widely held concept that heavy drafts on a mineral resource must lead to scarcity, reflected in rising prices. Three metals (aluminum, copper, and pig iron), two fuels (bituminous coal and petroleum), and two nonmetals (sulfur and cement) have been chosen because of their pre-eminence in their respective categories, their significance in an industrial economy, and the ready availability of their price records. It might be added that these seven commodities were selected before any price figures were compiled; none was selected or rejected to substantiate any preconceived notions as to price trends. The overall importance of the seven is demonstrated by the fact that, taken together, they composed over three-fourths of the value of all minerals produced in the U. S. in 1957. The first step in the analysis was to reduce the price records to a basis for significant comparisons. Two such comparisons have been made: 1) The quantities of each of the commodities that could have been purchased for an average hour&apos;s wage in each year, and 2) the unit price of each commodity through the years in terms of deflated dollars. These data are set forth in the accompanying table and two charts. The quantities of the mineral commodity purchasable with the average wage for one hour&apos;s work in all manufacturing industries through 1926 were based on annual average prices and on average annual wage rates determined by Paul H. Douglas and published in his "Real Wages in the United States, 1890-1926." The series was extended through 1957 by the Bureau of Labor Statistics, U. S. Department of Labor. Calculations based on these data show that the average worker could have purchased 1.28 lb of copper with his hourly wage in 1890, whereas his hourly wage would have purchased 8.11 lb in 1957, an increase of 633 pct in the 68-year period. An average hour&apos;s wage would have bought 10.85 gal of petroleum in 1890, compared with 33.04 gal in 1957. Even more spectacular is the increase in sulfur, of which 25.25 lb could have been purchased with the 1904 average hourly wage; 223.08 lb were purchasable with the wage in 1957—an increase of 883 pct. Comparable price data for sulfur are not available for years earlier than 1904. For every commodity, the calculations show an improvement in the wage earner&apos;s purchasing power in 1957 compared with the early years. Measuring purchasing power in terms of wages does not give an entirely fair picture of the availability of a commodity in an economy. When the efficiency of an economy changes and the balance shifts among such elements as raw-material production, manufacturing, and service trade, the economic significance of an hour&apos;s work changes. Partly to meet such criticism, but mostly to present another interesting measure of the response of minerals to changing market conditions, a second set of calculations has been made to deflate unit prices for the seven commodities into terms of 1954 dollars. To accomplish this adjustment to a common 1954 parity, the Gross National Product Price Deflator, developed by the Office of Business Economics, U. S. Department of Commerce, was used. Although the results of these calculations are not as striking as those based on labor&apos;s increasing purchasing power, nevertheless the declines outweigh the rises in the prices of the mineral commodities. In terms of these deflated prices, aluminum and sulfur are much cheaper today than in the early years; copper was substantially cheaper in 1957 than in 1890; pig iron and petroleum are little changed; and only bituminous coal and cement have increased substantially. Strangely, the two mineral commodities with the strongest reserve positions are the two to exhibit rising real prices. Now this apparent overall downtrend in prices has taken place during a period of almost fantastic increase in the demand for mineral products. The value of minerals consumed in the world during the period greatly exceeds all mineral consumption up to 1890. A stage has been reached in the U.S. in which 95 pct of the energy used is of mineral origin and in which machines, structures, roadways, communication facilities, and most other elements in the industrial economy are primarily of mineral origin. Even agricultural fertility is maintained, in large measure, by mineral fertilizers. A series published in Minerals Yearbook shows that the value of U. S. mineral products has risen from $615 million in 1890 to $18,000 million in 1957, a 29-fold increase. Even in deflated dollars, the increase has been eightfold, while population has expanded less than threefold. Not only are demands of the industrial nations— the U. S., countries of Western Europe, and Japan— increasing at rapid rates, but those countries with agrarian economies are calling themselves underdeveloped and clamoring to industrialize. The ever-expanding mineral requirements in the U. S. and throughout the world show no abatement. Mineral reserves frequently have been described as wasting assets. Much concern has been shown for future users, who have been pictured as finding themselves on a plundered planet. Conservationists have viewed the future with alarm and have demanded legislation and regulations to reduce the drain on mineral reserves.

Jan 1, 1960

By H. G. Landua, Leah L. Naugle, H. H. Lowry

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its (&apos;Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By Leah L. Naugle, H. H. Lowry, H. G. Landua

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its (&apos;Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By J. E. Pavlick, A. G. Guy

The total creep of tin alloys containing antimony in solid solution was observed to decrease with increase in antimony content. However, near the solubility limit an anomalous maximum in deformation was. found, in agreement with similiar observations by Bochvar. IT has long been recognized that alloys may deform more rapidly under stress if there is a tendency for a phase change or other structural change to occur simultaneously. However, the phenomena involved are complex and in some instances the opposite effect, strengthening, may result.&apos; This area of research has not attracted much interest in the western world, and although Russian investigators have studied it for the past 15 years their work has not received due attention here. Recently diametrically opposing views on one aspect of this problem have been espoused by two Russian investigators, Kornilov and Bochvar. The question is this: in certain binary alloys tested in creep at the temperature where the solute is at the limit of solid solubility, does the incipient formation of the second phase strengthen or weaken the alloy? Korni-lov&apos;s arguments in favor of strengthening were presented at the 1954 Symposium at the National Physical Laboratory, =Creep and Fracture of Metals at High Temperatures.The most recent statement of Boch-var&apos;s theory of weakening is in Oding&apos;s new book on creep and rupture.3 Although Bochvar agrees that strengthening occurs in some alloy systems, he argues that in certain alloys an anomalous weakening is observed. However, the extensive work of Korni-lov&apos;s group on creep properties of alloy systems has not revealed any anomaly of this type, but instead has tended to refute Bochvar&apos;s theory. This clear-cut controversy offered a good opportunity for a simple experiment to resolve the problem. The experiment and its results supporting Bochvar are the subject of this paper. However, it will be helpful first to sketch the present status of the larger question of the effect of a phase change or other structural change on plastic deformation. PREVIOUS WORK One of the first researches in this area was by Pfei1,37 who investigated the creep resistance of an 80 Ni-20 Cr alloy containing varying amounts of titanium. He found that the resistance to creep increased rapidly as the solid solubility limit in the alloy at 775&apos;c was approached and slightly exceeded. With further addition of titanium the creep resistance decreased, presumably because of precipitation effects. Bochvar&apos;s first work in this field was a study in 1945 of "superplasticity" in zinc alloys containing 15 to 25 pct Al.4 He found that alloys quenched from about 400 had anomalously low hardness when tested below this temperature. The following year, in a paper on the dependence of mechanical properties on the composition and structure of alloys,5 he extended some observations of Kurnakov to predict that at high temperatures of testing the hardness values for solid-solution alloys might be lower than those for the component metals. He also pointed out the influence of changes in solidus temperature in affecting curves of hardness vs composition, and he

Jan 1, 1962

By D. A. Dahlstrom

WITHIN the past decade, certain economic, legal, and technological changes have intensified the necessity for an efficient classifier or deslimer of particles at and below the 200-mesh point. First, mechanization of mining has increased the percentage of clays, silts, refuse, and high-ash material in the run-of-mine coal. Second, many washing plants must rely on smaller percentages of fresh make-up water because of shortages, economic factors, or legal restrictions on waste water disposal. Finally, the crushing of middlings and coarse refuse plus the trends toward the finer sizes in sales has further increased the amount of fines produced per ton of mine-run coal. A joint consequence of these circumstances has been the augmented percentage and build-up of —200-mesh material in the finer coal fractions and tipple circulating water. This results in the following disadvantages to the operator: (1) Higher ash percentages in the fine coal caused in large measure by the greater ash content of the —200-mesh material, (2) more difficult or expensive recovery of the fine coal from plant slurries, (3) lower filtration, drainage, and drying rates caused chiefly by lower permeability and the greater surface exposed per unit mass of the finer particles, (4) greater difficulty of beneficiatiing the fine coal because of lowered equipment efficiency and the partial "coating-out" of the —200-mesh fraction on the coarser coal particles. Obviously some cheap but effective fine-size classifier must be developed to aid in solving the above problems. To eliminate the generally unwanted —200-mesh fraction from coal slurries, several methods are in use. Probably the most popular with coal operators is the settling cone wherein the larger particles settle downward to the apex of an inverted cone while the slimes and fines are carried upward by vertical fluid currents caused by the overflow of the bulk of the water at the outer rim. The main advantage of the unit is the low initial and operating cost since no moving parts are involved. Disadvantages are primarily low capacity per square foot or floor space and the loss of good coal in the overflow above the 100-mesh size due to localized, high-velocity gradients and nonuniform, fluid-flow patterns, especially at high loadings. Also, when high slime concentrations are present, desliming efficiency is severely injured.&apos;, &apos; Other methods employed are the drag and spiral classifiers and the hydroseparator.&apos; These involve mechanical separations achieved by moving parts and naturally result in higher initial costs. As they are all based on the settling velocity of the particles at the mesh of separation under operating conditions, area requirements are again large per gallon of throughput if they are to classify at the 200-mesh point. Usually the selection is made to operate at a higher throughput and thus sacrifice some coarser coal in the slime overflow. Cyclone Possibilities in Desliming To overcome the disadvantages of present deslirning methods, it is necessary to use a device that exhibits a very stable and uniform flow pattern while greatly increasing the settling velocity of

Jan 1, 1952