Search Documents

By Benjamin F. Tillson

Although portable fire extinguishers are valuable for fires in an incipient stage, some medium that will dissipate a large amount of heat is needed to fight a fire in mine timbers, because of the size to which the fire will probably have grown before it is discovered. Scaling off, or otherwise smothering such a fire with gases that will not support combustion, is often ineffective for the residual heat will cause reignition when the area is opened and fresh air reaches the hot charred timber. The most effective ways of fighting mine fires, therefore, are to drown and cool the hot zone with water, and to "load out" the partly burned material. Either of these methods requires a direct attack of water ; upon the inflamed material; therefore, every mine containing a large ' quantity of timber or other combustible should be as completely equipped with a fire-hydrant system as it is with compressed-air mains. Mine managers may object to the expenditure, especially if they have not suffered from mine fires. The cost of such preventative measures, however, is only a small portion of the possible losses, and the water pipes can be used for other purposes, which will pay the carrying charges. They can supply water to the rock drills, which will encourage more wet drilling with hollow-drill steel, for the trouble and expense of packing water to individual tanks at the drills will be removed. The carbon-tetrachloride hand extinguishers seem to have no place in mining except for fires that start in electrical equipment. They give off noxious gas, which may prove poisonous in confined quarters; and as it is heavier than air it is of no value for smothering fires overhead or in side timbers and would be dissipated by a good ventilating draft. The old soda-acid extinguisher or the more modern "foam" types ' are preferable. The former probably does not rely for its efficacy on the carbon dioxide generated but on the smothering and cooling effect of the water and the trajectory of stream that may be obtained because of the gas pressure developed. The production of a foam having a tough film to smother a fire, even on overhead surfaces, with the added

Jan 1, 1923

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

By L. A. Mekler

The recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to those produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack. The convection-type oil still is particularly suitable for the application of flue-gas recirculation. In an oil still, the heating of the oil is accomplished by applying to the tube surfaces a given quantity of heat of a certain predetermined quality, usually with the initial temperature of the gases not over 1500" F. as measured by thermocouples placed above the tube bank. To obtain the full benefit of the heating surface of the coil, the final temperature of the gases, after passing over the coil, is kept 200" to 300" higher than the temperature of the incoming oil. This final temperature varies from 500" F. for a topping still with only a slight or no

Jan 1, 1928

By O. C. Ralston

THE use of copper sulfate for improving the flotation behavior of sphalerite is probably at least 15 years old. The original discovery of its activating influence is somewhat obscure. The story goes that in the mill at Mascot, Tenn., its favorable action was discovered by accident, early in 1914, as follows: The original laboratory test work on a sphalerite ore gave favorable flotation results, but after a mill had been built the flotation concentration of the ore was very unsatisfactory. In diagnosing the probable reasons, one fact pointed out was that the laboratory test machine had been constructed of bronze whereas the commercial machine allowed pulp to come in contact only with wood and iron. A plate of sheet copper was hung in the flotation machine and results immediately improved. At first fanciful explanations of electrolytic and electrostatic behavior were given credence, but when the copper plate was removed and a small amount of copper sulfate substituted in the pulp an even more favorable result was obtained. Toward the end of 1914 copper sulfate was also adopted in the acid flotation circuit of the Butte and Superior Copper Co. Just who is responsible for the original discovery the present writers do not know: It seems strange that in that era of flotation litigation this discovery was not patented. While for pragmatic purposes it may be sufficient to know that the mere addition of copper compounds to a flotation pulp is sufficient to activate the flotation of the sphalerite, for scientific purposes it is quite desirable to know more about how the action takes place. It is the purpose of this paper to present certain evidence dealing with the mechanism of the beneficial effect. The description of the effect as activation in contradistinction to depression is now common in both the English and German languages. It makes no assumptions as to whether the zinc sulfide surfaces have been filmed with copper compounds. In fact, the principal differences of opinion expressed in the literature deal with whether there is an actual formation of CuS (or even Cu2S) on the surface of the sphalerite.

Jan 1, 1929

By H. D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge-—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. Rut discrepancies arise. Every maker and every User of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

Jan 1, 1928

By R. J. Brison, R. D. MacDonald

This chapter is written primarily from the standpoint of development of flotation processes for treatment of specific ores. However, most of the principles and techniques discussed are equally applicable to other forms of applied flotation research such as improvement of procedures in existing plants and development of new reagents or methods without reference to specific ores. Because it is not possible to cover this subject in detail here, much of the material presented is in the form of a guide to the literature, with emphasis on readily available, English language publications. Details are included only if considered to be widely applicable or not readily accessible in the literature. Related subjects which are covered elsewhere in this volume, such as flowsheet design and statistical techniques, are not emphasized in this chapter. The material presented is intended primarily for those familiar with the theory and practice of flotation, but with limited experience in applied flotation research. It may be of value to the experienced investigator as well, by calling to his attention some useful viewpoints or techniques that he may have overlooked. It has often been said that flotation is more of an art than a science. In- deed much of the knowledge of flotation behavior is empirical. However, the unsystematic, artisan approach to flotation problems results only in an ac- cumulation of unrelated data. Like any other physical or chemical process, flotation is amenable to investigation by systematic experimental methods. The experiments should be based, as far as possible, on an understanding of the natural laws that govern the process and on good experimental procedures. SAMPLING OF A DEPOSIT In working out a flotation process for a mineral deposit, no step is more important than that of obtaining a suitable sample or samples. Experimental procedures cannot compensate for the lack of a representative sample. Methods of sampling a deposit have been published elsewhere,l-4 but a few points are of special importance from the standpoint of flotation. First, the sample should be representative of the deposit, not only in respect to chemical composition, but also in respect to mineralogical composition and degree of dissemination of the valuable minerals. To help ensure

Jan 1, 1962

A High-speed Dilatometer and the Transformational Behavior of Six Steels in Cooling. By Arthur L. Christenson, Edward C. Nelson and Clarence E. Jackson. (With discussion).................................606 Dilatometric Studies of the Graphitization of Cast Iron. By N. A. Ziegler. With discussion) 627 An Interferometer Type of Dilatometer and Some Typical Results. By- L. '4. WIlley and W. L. Fink. (With discussion).........................642 The meeting was held in the Pine Room of the Statler Hotel, Cleveland, Ohio, on Tuesday afternoon, October 17, 1944. The chairmen were F. M. Walters, Jr. and Howard Scott. Introduction F. M. Walters, Jr.—The principal advantages of the dilatometric method perhaps are two, as compared with the method of thermal analysis. One is that the dilatometric method can be applied with a large variety of rates of heating and cooling, whereas thermal analysis—that is, the study of the transformational characteristics by means of heat evolution—is limited to the rates of heating and cooling that reveal the evolution of heat. The dilatometer can be used for the study Of reactions at zero rates of heating and cooling; that is, isothermal reactions. As you will hear this afternoon, the rates have been pushed up as far as 500°C. a second. The other advantage is that the dilatometric method shows that a two-phase region is a two-phase region, whereas the thermal analysis merely reveals the temperature at which the rates of heat evolution are greatest.

Jan 1, 1945

By W. P. Lass

Discussion of the paper of W. P. LASS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 103, July, 1915, pp. 1443 to 1447. ROBERT M. KEENEY, Somersville, Conn. (communication to the Secretary *).-There is not only a possibility of improvement in present methods of treatment of the byproducts of refining in the cyanide plant by the use of the electric furnace, but also in melting and refining of gold precipitate. This interesting paper by Mr. Lass shows an electric furnace in successful operation in a large plant for the treatment of by-products. Electric melting of cyanide precipitate is a cheaper form of treatment in many cases than any of the combustion methods now used because of the high cost of oil, coke or coal in many camps, while on the other hand electric power may be had cheaply, especially in a place where there is possibility of development of high-head hydro-electric plants for power purposes. Also, if the oil-fired tilting furnace is used for direct melting of the precipitate, as is the case at many small mills, a great saving in cost is made by the use of the electric furnace because of the high crucible cost in melting with the tilting furnace. A study of this paper indicates the cost of the operation approximately. Consider all the fluxes to be turned in as byproducts and coke at $18 per ton.

Jan 12, 1915

WHOEVER has occasion to judge tin in its whiteness from the testimony of his eyes alone would surely believe it to be purest silver, or something that comes very near to it in nature. This is even more so when, on handling, it is found to be harder than lead, to which it can be said to have a greater and closer resemblance. But whoever has actual experience with tin knows that none of the other metals is less similar to it than silver. For silver mixes with every metal, as does gold; and they unite together, and the others do likewise; and except for their color they change their natures but little. But this metal tin, wherever it is found, acts like a powerful poison which envenoms and corrupts the others; and it does this not only with large quantities but also with every small amount; indeed just the trace remaining where it has been melted is enough to embrittle silver and gold as well as iron and copper. The greater the quantity of it in these, the greater are its effects. Speculators of natural causes say that this fact arises from its great wateriness, which is very subtle and poorly decocted and almost like that of quicksilver. This wateriness, then, by means of its subtlety which joins itself with metals, imposes itself into that unctuous and viscous material which renders them flexible, and thus deprives them of their toughness

Jan 1, 1942

Mother Earth has had a long life extending over two billion years, during which time she has changed from a mass of incandescent gases to her present form, exhibiting a density stratification from the extremely tenuous gases of the stratosphere to the heavy central nickeliron core. Man is now mining all the principal divisions of Mother Earth except the centrosphere. Nitrogen, oxygen, neon, and other rarer gases are being recovered from the air; magnesium, bromium, potash, borates, and other salts from lakes and seas; brines, medicinal mineral waters, and great quantities of water for domestic and industrial uses from surface and subsurface reservoirs; and, from the rocky crust, many minerals and fuels for our present industrial civilization as well as plants and animals for food and shelter. Productivity of soil is influenced both positively and negatively by man. There is some cause to bewail what may be considered a wasteful influence of men on soil. The general situation is bad in spots but not hopeless. The passing of large areas of fertile land in some areas is merely to be noted and not to be mourned. These lands could not have been used without decrease in their fertility. The productivity factor is affected by human activities. Many soils in the eastern and southern states are far richer and more productive now than they were at any previous time. Arctic soils are not productive

Jan 1, 1950

By R. S. Hadi, L. Svarovsky

SUMMARY This is a report of a new development in on-line particle size measurement of fine powders in dust-laden gases. A continuous sample of the solids-air suspension is drawn from the process stream via a sampling probe by means of an air operated ejector into a cyclonic separator whereby the sample is subjected to a particle size dependent separation process and split into two streams, "overflow" and "underflow". The overflow stream carries most of the fines at a relatively low concentration and the underflow stream carries the coarse particles at a relatively higher concentration. The concentration of solids in the two streams is detected by electrostatic noise level technique which utilises the electrostatic charge accumulated on the solid particles due to their high velocity in the turbulent air stream, for the mass concentration measurement. The ratio of the solids concentration of the fines stream to that of the coarse stream is then correlated against the average particle size in the main process stream by a calibration curve. The in-plant tests clearly indicate that this relatively simple instrument offers good sensitivity in the size range from 2 to 6 µm, and is capable of giving a continuous indication of average particle size for process control purposes. Although the instrument was developed for a particular application, it may be used in other situations where fine powders are conveyed in gas streams. British and foreign patents are applied for.

Jan 1, 1980

By Emery C. Olsen

Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that influence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25 % and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the south- west. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development.

Jan 10, 1963

By E. G. Bailey

The bituminous coal industry faces a real problem, if it desires to retain the position in the power-generation field to which it is economi-cally entitled. More power is probably produced today for electrical energy, for steam-driven and steam-heating industries and processes, for transportation by rail, water, highway and air, collectively, than ever before, and yet the total bituminous coal production has decreased about 38 per cent, from 575,000,000 tons in 1926 to 357,500,000 tons in 1934. It is not the intention of the writer to recommend coal as a fuel for automobiles and airplanes, but rather to point to these forms of transpor-tation as being responsible in a very measurable degree for reducing the coal consumed by railroads. Petroleum products may still further reduce consumption of locomotive fuel through the extension of the use of Diesel-driven trains. Oil-burning steam-driven locomotives are replacing coal in some places, where railroads operating high-speed pas-senger trains are willing, temporarily at least, to pay a premium for the fuel, that is low in ash and produces less smoke and practically no cinders. In the navy and ocean-going passenger ships, oil is so firmly estab-lished, and has such definite advantages over coal as formerly fired, in steaming radius, in ease of bunkering, cleanliness, and reduction in firing labor, that very outstanding developments in the handling and burning of coal will be required in order to replace oil. For freighters on the Great Lakes, coal is the logical fuel, but there is great and immediate need of radical improvements in its use, else that market also may be lessened. It is not within the scope of this paper to discuss in detail bitumi-nous coal for either locomotive or marine use, but, rather, generation of power in stationary plants, consisting of electrical generating stations and that very large group of miscellaneous industrial plants, such as paper, rubber, textile, steel and other industries that use electrical, mechanical, and steam power, derived from either hydro or some form of fuel.

Jan 1, 1935

By A. S. Rhea

SALT-WATER disposal in the East Texas field by means of injection into the Woodbine sand is a relatively new procedure. The purpose of this paper is to present what has been accomplished to date in this field, with-out detailed discussion of other means of disposal, such as surface impound-ing for evaporation or release into surface streams. Subsurface disposal of salt water is still in an experimental stage in the East Texas field, and, though water can be injected into the Woodbine sand, the economic problem is not as yet solved. As past experience has been that fields producing from the Woodbine formation produce large quantities of salt water, it was assumed early in development of East Texas that it would be necessary to dispose of a tremendous quantity of salt water in the later periods of production. There has been a gradual increase in the amount of salt water pro-duced in the field, until at present it is about 200,000 bbl. per day from approximately 4400 wells. It is only natural to expect an increase in the number of wells producing water, as well as the amount of water produced in the future, and it has been estimated that if present practices con-tinue the production of salt water may ultimately be as much as 700,-000 bbl. per day. The Woodbine sand is found in the East Texas field at an average depth of 3650 ft. The oil-bearing portion of the sand lies between the depths of 3050 ft. below sea level, on the east edge of the field, and 3320 ft. below sea level on the west, which depth was the estimated original average oil-water contact. The Woodbine sand under the field has the form of a broad tilted wedge pinching out on the eastern side of the field and dipping gently into the East Texas Basin toward the west. The Woodbine sand in the East Texas field has an average porosity of approximately 25 per cent and is highly permeable, the average being about 1300 millidarcys.

Jan 1, 1940

By C. A. Heiland

The Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station, whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of LOO meters, as under most circumstances it is difficult to level along a arger concentric circle about the station. Principle of Topographic Correction The principle of all topographic corrections is to assume a homogene-ous compositon of the masses around the station in regard to specific gravity as well as a mathematical shape of the topography. The results become the more accurate the closer this mathematical shape is to the actual configuration of the terrain, but naturally the amount of necessary computation also increases. If a standard correction with fixed dis-ances is adopted, the middle error of this method will, therefore, increase as the irregularity of the terrain. Hence, the application of the torsion balance in mountainous areas may be successful only if the disturbances due to heavy masses underneath the surface are so large as to exceed onsiderably the increased middle error due to rugged topography, or,

Jan 1, 1929

By Carl Trischka

During fifty-three years of mining operations in the Warren mining district, the mineralization has been found to cover an area roughly 2 miles long by 155 miles wide. Ore extraction from the richer portions of this area has been closely followed by surface subsidence. At the western end of the district, where the ore outcrops at the surface and oxidation is more complete over a wide area, intense surface disturbance is visible in the form of closely spaced open cracks and escarpments. As work has progressed toward the east, more unoxidized ore-bodies have been found and mining has been at increasing depth, for which reasons surface subsidence is less intense and subsidence blocks become larger and in general are bounded by open cracks, which persist over long distances. There may also be traced on the surface what appears to be a boundary crack, running in a northwest-southeast direction, marking the present southerly limit of subsidence of the district as a whole. It is not completely developed, and has not as yet appeared over the very deep mining operations in the extreme easterly portion of the district. Check surveys show that vertical and horizontal dislocation is still taking place. All of the various mining operations, including open-pit work in porphyry ore and underground mining of limestone replacement and porphyry ores, have had their influence in disturbing the surface. As these influences frequently overlap, and because the surface disturbance is continuous over practically all ore occurrences, it is virtually impossible to choose an area sufficiently isolated to ascribe the amount of subsidence to any definite volume of ore removed. After due consideration of all factors, there has been selected for discussion an area 1400 ft. long by 1200 ft. wide, which will be referred to as the Queen Hill block. It is bounded on all four sides by faults, which tend to limit subsidence disturbance to that caused by ore mined from within the block, and likewise to prevent subsidence cracks due to mining outside of the block from entering the area.

Jan 1, 1934

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By H. Shaw

It is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment. In certain of the various oil-producing areas of the world, and particularly in the Gulf Coast region, the geology may be regarded as comparatively simple, while the oil is usually associated with a large and well defined structure such as a salt dome or anticline, which is capable of giving gravitational indications sufficiently extensive to be detected by the torsion balance over a fairly wide area of the ground surface. It is customary, therefore, during the preliminary survey of an area for oil, to

Jan 1, 1929

By Karl Sundberg, Allen Nordstrom

Interesting results were recently obtained in geophysical prospecting at the Questa mine of the Molybdenum Corpn. of America in New Mexico. This paper describes that survey, which was carried out during October and November, 1927, by the Swedish American Prospecting Corpn. It is hoped that the paper will make it possible for the mining man to form an opinion of the applicability of geophysical prospecting under difficult conditions, showing, as it does, the results when prospecting for small small orebodies with comparatively poor conductivity, in a region of rough topography. Some principles underlying electromagnetic prospecting not known to be published previously will also be given in an elementary way, with special attention to the general structure of the electromagnetic field. Geological. Conditions at Questa The property is situated in the Taos range of the Rocky Mountains in northern New Mexico. About this region, L. C. Graton says:' The main range is made up of Pre-Cambrian granites, gneisses and schists but in the vicinity of Red River igneous rocks of later age are present almost to the exclusion of the older series. These younger rocks are divisible into two groups. The older of the two, probably Pre-Tertiary age, is represented by large intrusive masses of monzonite porphyry, usually containing considerable quartz. The more recent group comprises intrusive and probably effusive dark-colored andesites and coarse andesitic breccias, some of which contain fragments of the monzonite; there are also flows of rhyolite and beds of rhyolite breccia. The evidence regarding the relative age of the andesite and the rhyolite is not wholly satisfactory, but there is little doubt that the andesite is the older. The ore deposits, although occurring more commonly in the monzonite porphyry than in the rhyolite, nevertheless are believed to be genetically related to the rhyolite. They certainly cut the rhyolite or andesite in places, and hence fall in the late Tertiary. The molybdenite at the Questa mine occurs in veins in the alaskite granite porphyry belonging to the older part of the Pre-Tertiary eruptives. Overlying the granite porphyry is the granodiorite, capping the granite

Jan 1, 1929