Search Documents

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.' In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,' the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

By B. F. Decker, D. Harker

The recrystallization reaction in OFHC and spectroscopically pure copper has been followed by X ray diffraction determinations of the amount of material with the cold-worked and recrystallized textures in specimens which had been given various heat treatments. The heats of activation for recrystallization are found to be: 29.9 kcal per rnol for OFHC copper and 22.4 kcal per rnol for spectroscopic copper. A reliable and speedy method for measuring the amount of recrystallized material in a piece of rolled metal, together with a new scheme for low temperature heat treatment, have made possible a determination of the activation energy for recrystallization in rolled copper. This method for studying recrystallization rates is different from others reported in the literature.' Oxygen free, high conductivity copper—OFHC copper—of purity 99.98 pct gave an activation energy for recrystallization of 29.9 kcal per mol with recrystallization data taken in the temperature range 208-245°C. Copper of purity 99.999 pct from the American Smelting & Refining Co. gave an activation energy for recrystallization of 22.4 kcal per mol with recrystallization data taken in the temperature range 43-135°C. The great change in activation energy for recrystallization as the small amount of impurity in the metal is decreased suggests that the motion of grain boundaries is conditioned by the impurities which must be concentrated in them. Thus the OFHC copper recrystallizes with an activation energy of the order of magnitude to be expected for the diffusion of the kind of impurities likely to be present. The high purity copper, on the other hand, recrystallizes with a much lower activation energy, in accord with the notion that the grain boundaries need not wait for the impurities to diffuse with them. Copper when strongly cold-rolled has a well-defined crystallite texture which can be described by saying that the [111] direction of the face- centered cubic crystals is aligned approximately in the cross-rolling direction and that faces of the form {110} lie approximately in the rolling plane. When such rolled copper is completely annealed the crystallite texture is quite different: the [loo] direction is in the cross-rolling direction and faces of the form (100) are in the rolling plane. At intermediate stages of annealing, the copper contains both textures. If a Geiger counter X ray diffraction spectrometer is set up so as to measure the intensity of the (200) Bragg reflection from the rolled surface of a piece of copper strip, this intensity increases from a very small value in the cold-worked state to a maximum as the specimen is annealed. The same would be true for (200) reflections from planes normal to the rolling or cross-rolling directions. In view of this fact, the amount of material in the copper which has recrystallized can be measured by comparing the intensities of one of these reflections just mentioned with the intensity from a similar specimen after complete annealing. In much the same way the intensity of (111) reflections from planes normal to the cross-rolling direction could be used to measure the amount of unrecrystallized material in the specimen. In the work to be described here the amounts of recrystallized and unrecrystallized material in partly annealed rolled copper specimens were determined in this way. Experimental Procedure Samples of oxygen free high conductivity (OFHC) copper, cold-rolled 99.7 pct to 0.002 in. thickness, were subjected to heat treatments for various chosen times at four different temperatures, and high purity copper samples, cold-rolled 98.0 pct to 0.0015 in. thickness, at six different temperatures. Each sample, after treatment, was placed in an orientation sample holder for use with a Geiger counter X ray spectrometer and a reading was taken of the intensity of the (200) reflection from planes perpendicular to

Jan 1, 1951

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By E. A. Holbrook

AT the meeting of the Committee on Engineering A Education of the Institute at the New York meeting last February, it was brought out that the number of men graduating in mining engineering from our colleges at the present time is not sufficient to meet the ordinary needs of the mineral industries. Following the meeting, Samuel S. Wyer, consulting engineer of the Fuel-Power Transportation Educational Foundation of Columbus, Ohio, prepared a pamphlet called "Mining Engineering's Appeal to High School Seniors." Under the auspices of this Foundation the pamphlet is being sent to every high school in the United States. The pamphlet does not in any way paint glowing word pictures of the profession; rather it is a statement of the importance of mining engineering in our present-day civilization, together with the requirements in young men who are looking forward to an engineering career.

Jan 1, 1930

By K. R. Crocker

PRIMARY blasting at the open pit of the Cananea Consolidated Copper Co. has been developed to meet several conditions peculiar to the operation. Mining at Cananea is not confined to the open pit but is in conjunction with the underground mine which has been in operation for many years. Several old stopes included in the pit area were filled with waste obtained in stripping for the pit. The main haulage tunnel for the underground ore passes directly under one section of the pit and at present is but 180 ft below the pit floor. The pit as originally laid out called for an overall final pit limit slope of 60°. However, the upper 275 ft - a fairly soft oxidized capping, was carried at a 50° slope and the lower benches, which constitute 750 ft in combined height, are being mined to an over-all final slope of 60°.

Jan 6, 1950

By H. O. Hofman

Discussion of the paper of H. O. HOFMAN and JOHN BLATCHFORD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1915, pp. 91 to 97. ROBERT H. RICHARDS, Boston, Mass.-I should like to ask Professor Hofman whether he is able to roast his stibnite without any comparatively large amount of loss of antimony? H. O. HOFMAN, Boston, Mass.-Yes. The last statement I made was that the loss of antimony, during those tests, increased with the temperature, and that up to 372° C. there was no loss whatever in antimony, also that it increased to 4:2I per cent. with 545° C., the highest temperature that we obtained in our small furnace. ROBERT H. RICHARDS.-I should like to ask a second question, and that is, is it not true that stibnite can be roasted more completely than any other sulphide?

Jan 5, 1916

On Apr. 21, the Victory Liberty Loan was offered to the public. This Loan is made necessary by the expenditures incident to closing of the war. As in preceding Liberty Loans, an intensive campaign is being conducted, and this Committee is to obtain and record subscriptions from the Industry of which you are a part. I am sure you feel as I do in wishing the Mining Committee to make as good a showing as possible. By placing or recording your subscription through us will help your Committee to make its proper showing, and, as heretofore, your transaction can he carried out with any bank or trust company you may prefer to designate. Payment may be made in full or in six instalments. In either case, 10 per cent. will be required on or before May 10. Subscription blanks will be mailed to you as soon as available. CHARLES HAYDEN, Chairman.

Jan 5, 1919

The research project on size reduction, sponsored by the mining industry through financial support from individual companies, is now embarking on a second three-year program. The first 3-year program had as its objectives assimilation of the literature on comminution and development of simulation programs encompassing the basic mechanisms of grinding. This involved investigating conditions under which a particle in a mill is captured, the stress to which it is subjected, its break probability, and the resulting particle size distributions. The results were used to obtain the most representative simulation models based on current knowledge of mechanisms. As part of this work a set of computer programs has been developed for the following cases: . Batch mill, by numerical integration for completely general selection and breakage functions. . Continuous open-circuit mill by same method as above. . Continuous open-circuit mill by general numerical integration method, including transient behavior

Jan 1, 1969

The Institute offers two distinct relationships to. students: one is an individual relationship as a Student Associate; and the other is a relationship with local organizations of students, known as Student Chapters of the AIME This individual relationship is set forth in Section 8 of Article I of the AIME Bylaws, as follows "A student in good standing in an approved school, who has been nominated by at least three instructors of the nominee (one of whom must be an Institute member), may affiliate with the Institute as a Student Associate by payment of $4.50 annual fee, for which he shall receive one monthly journal and be privileged to attend meetings of the Institute and to use the Engineering Societies Library and the Personnel Service A student may remain such until December 31 of the year in which he ceases to be in university residence as a student "

Jan 1, 1952

INTERNATIONAL ENGINEERING CONGRESS This Congress will be held under the auspices of five National Engineering Societies, of whi h the Institute is one. The sessions will be held in 11 sections and the proceedings will be published in 10 volumes of 500 pages each, of which Volume 8 will contain the papers and proceedings on Mining Engineering and Metallurgy. The membership fee of $5 will entitle the holder to the volume of General Proceedings and Index, and, in addition thereto, any other single volume chosen. Other volumes may be subscribed for according to a sliding scale depending upon the number of volumes taken. The Institute will have a meeting in San Francisco during 1915, and it is desirable for our members to join the International Engineering Congress at in early date in order that their support of the enterprise may be given in its early stages, when it is most needed.

Jan 2, 1914

By Edward Gridley

At the meeting of the Institute, held at Roanoke, Va., in June, 1883, I gave some facts in relation to charcoal pig iron of unusual strength, made from our carbonate ore taken from the mine at Amenia, N. Y. My object in again bringing the subject to the attention of the Institute, is to obtain, if possible, the solution of a prohlem in connection therewith. Our furnace is of the old type, stone stack 32 feet high by 9 feet 2 inches at top of bosh; bosh about 67O pitch; stone hearth; three tuyeres of 31/4-inch opening; fuel, a mixture of hard and soft coal; blast about & to # pound pressure, and heated to 400' to 600° Fahr. by iron pipe oven on top of stack. The analysis of the roasted carbonate ore, as before given to the Institute, is as follows:

Jan 1, 1884

G. H. CLEVENGER, Colorado Springs, Colo.-Mr. Crowe's paper will be of great interest to cyanide operators, as it is a distinct new development in cyanidation. After reading the paper it occurred to me that some of us had done practically the same thing some time ago, but without design and unconsciously. I refer particularly to the operation of some of the earlier types of vacuum filter, used in connection with a dry vacuum pump and a receiver, which is somewhat similar equipment to that employed by Mr. Crowe. However, we did not appreciate the good effects we were getting from such of this solution as was precipitated, and it has remained for Mr. Crowe to bring distinctly to our attention the advantages of removing air from cyanide solutions before precipitation. Full credit is therefore due him for this very clever improvement in the cyanide process.

Jan 11, 1918

By William L. Payne, Edward E. Ives

A unique feature of Potash Co. of America's A new potash property near Saskatoon, Sask., is the use of semi-dome-shaped buildings for product storage. Four domed structures, timber-framed and corrugated-sheet covered, are being built; each designed to handle 20,000 cu yd. The relatively small capacity units, PCA believes, give flexibility not only in storing different grades and sizes of product, but also in permitting greater ease in shipping products as market demands change. The domed buildings are 150-ft diam, comprised of a 16-ft-high concrete wall base, topped with a metal sheet-covered octagonal timber frame. The dome of each unit is designed to fit very closely the angle of repose of the contained material, which results in the maximum usable volume. The entire roof is flood coated with a bitumin to provide a complete weather seal.

Jan 9, 1959

By John F. Abel

A good mining engineer is supposed to make a good mine. What then makes a good mining engineer? There certainly are a lot of answers to that question. The answers depend on whether you are one, work for one, or employ one. There are several cliches about mining engineers, and there is some truth in them-as there usually is in any stereotype. Hollywood chose Jeff Chandler to portray a mining engineer in Foxfire. The image here was of an almost one-man mining operation. When Chandler picked up a jackhammer, cradled it in his gut and started drilling out a tunnel round, it gave one the hives. I would have liked to see him finish just one round that way. There are limits to what even the most hairy-chested of us will try. We can assume that Hollywood feels it needs to over- draw any profession to add impact.

Jan 1, 1970

By R. M. (Mike) Robb

Introduction The requirements to investigate a wide range of alternatives and analyze a variety of ‘what if’ questions make the automation of pit design a requirement in today’s rapidly changing mining industry. The wide-spread application of computers has relieved the engineer of much of the tedious and error-prone work related to mine design. He is thus free to do the creative and innovative thinking for which he is trained. It is now possible to investigate a large number of alternative pit designs in a reasonably short time period. In the past it was very easy for a team of engineers to consume 12 to 14 man-months in the detailed hand design of a large open pit. The pressure of today's mining industry, the desire to investigate a variety of alternative designs, and the shortage of qualified engineers make the slowness of hand design less preferred.

Jan 1, 1979

By L. C. Brown, E. B. Hawbolt

If a single-phase alloy is rapidly cooled such that insufficient time is available for an equilibrium transformation to occur, the high-temperature phase may be retained to room temperature or may undergo a massive or martensitic reaction. The massive or martensitic product develops without a composition change and usually has a crystal structure approximating an adjacent equilibrium phase. The characteristics of a massive transformation are intermediate between the equilibrium reaction in which long-

Jan 1, 1969

By Lewis Stockett

During the year 1903, a building having machinery corresponding to ail anthracite-coal breaker was erected at the town of Stockett, Cascade county, Mont., for the purpose of breaking-up and cleaning bituminous coal. The coal is mined from a vein of the Kootenai group of the Lower Cretaceous measures having the following section: The vein is nearly horizontal in position, and each bench differs in quality as shown in Table I.

Jan 1, 1905

By Richard R. Klimpel

The role of dispersion is described in the wet grinding of ores using tumbling media mills and the flotation of coal, sulfide, and non-sulfide ores. Emphasis is placed on characterizing the effects of dispersion in laboratory tests using engineering models which provide information useful for the improvement and control of existing plant operations. Significant economic gains in the above named operations have been realized using these models as guides for full- scale plant testing.

Jan 1, 1980

By S. K. Kawatra, R. A. Seitz

The use of inferential particle sizing for closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1984