Search Documents

Edward Eeller, Baltimore, Md. (communication to the Secretary): Mr. Miller's improved method of the cyanide-assay for copper will, without doubt, be much appreciated by assayers and chemists who are engaged at copper mines and works. The writer, as one who, at one time, had much work of that kind to do, entertains no doubt of its practical value. In enumerating the factors which affect the accuracy of cyanide-titration, Mr. Miller omits to mention time. This I have always considered an essential one; i.e., in order to secure accuracy, I have believed it to be necessary to run the cyanidesolution at the same rate of speed in standardizing as in the titration of the samples. I have accomplished this, without the use of a time-keeper and without noticing the volume of the solution, in the following simple manner: In running the cyanide-solution from the burette, the stream was so regulated, by manipulation of the cock, that it retained its continuity for a distance of about one inch below the orifice, and, below that, broke into individual drops. This means that a constant pressure is maintained at the orifice of the burette, so that, during equal intervals of time, equal volumes of the solution pass through. The stream of cyanide-solution was left to flow in the manner indicated until the blue ammoniacal copper-solution began to show a distinct change in color, after which the cyanide was added by drops at regular intervals until the desired end-reaction. When several burettes are used they should have orifices of equal diameter; otherwise, the timefactor must be considered separately for each. In accordance with Mr. Miller's views, I have always considered the cyanide-method as of very satisfactory accuracy for all copper-assaying in which I did not employ the electrolytic method. It may interest some of my colleagues to know the modified method which I employed some fifteen years ago in making great numbers of copper-estimations on ores and

Jan 1, 1902

The regular activities of the Insti¬tute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $560,000. An active effort is being made to in¬crease the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman; Paul D. Merica, vice-chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, John V. M. Dorr, Howard N. Eavenson, D. C. Jackling, Henry Krumb John M. Lovejoy, Harvey D. Mudd and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1943

By Leon Eliel

TEN years ago .a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these. isolated bits of infor-mation can be ascertained, the message begins to take meaning.. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936

Jan 1, 1977

By Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodity in this volume has as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as fluxes, glass raw material, refractories, fillers, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Recent. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1981 about 644 million tons were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses, with emphasis on developments since 1960. In doing so we borrowed extensively from our report on the applied geology of limestone and dolomite (Rooney and Carr, 1971). The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired down in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information. Geology Mineralogy The principal carbonate rocks used by industry are limestone and dolomite. Limestones are sedimentary rocks composed mostly of the mineral calcite (CaCO3) and dolomites are sedimentary rocks composed mostly of the mineral dolomite (CaCO3 • MgCO3). Aragonite (CaCO3), which has the same chemical composition as calcite but a different crystal structure, is economically important only in modern deposits, such as oyster shells and oolites. Aragonite is metastable and alters to calcite in time. Some other carbonate minerals, notably siderite (FeCO3), ankerite (Ca2MgFe (CO3)4), and magnesite (MgCO3), are commonly found associated with limestones and dolomites but generally in minor amounts. Because of their similar physical properties, the carbonate minerals are not easily distinguished one from the other. Specific gravity,

Jan 1, 1983

By Ward W. Minkler

Since 1978, the titanium metals industry, throughout the non-socialist world, has experienced a period of growth and prosperity unparalleled since the late 1950s. Sponge producers, melters and mill product manufacturers have operated at capacity, record shipments have been attained, new producers have entered the industry and established producers have implemented expansion plans. However, there is now mounting evidence that the underlying elements which generated this vigorous surge have abated, at least temporarily. It now appears that in 1982, the industry will encounter overcapacity, excessive inventory accumulations and the probability of declining prices. Therefore, it does seem appropriate that we now take inventory of the present and future markets for titanium with the hope we can identify both near term opportunities as well as challenges the industry now faces. If we view the development of titanium markets as a function of time, they fit rather neatly into three sectors.

Jan 1, 1982

A. Scott Reid, London, Eng. (communication to the Secretary*) :—As a constructor of several glass mine-models, .I have read with much interest the description of the model of the Montana-Toriopah mine-workings by Edmund D. North.

Jan 1, 1910

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,'' for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,'' for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Thomas MacFarlane

AMONG the industrial enterprises which have, from time to time, been undertaken in our Dominion, few have been more uniformly unsuccessful than those which have had for their object the develop ment of our mineral resources. These resources hare not been re garded as insignificant. On the contrary, it is supposed that we possess in our ore deposits something more than mere points of mineralogical interest. Some people are enthusiastic enough to be lieve that our mineral wealth will yet occasion the establishment in our backwoods of happy and industrious communities, causing, in fact, our wilderness to blossom as the rose. These enthusiasts do not shut their eyes to the serious obstacles which at every stage in terfere with the carrying out of mining enterprises in this country, and which tempt one to believe that no such enterprise can ever be conducted to a desirable end, but they entertain the conviction that as our capitalists, miners, and technologists reach the years of discretion, and handle our mines in an economical, vigorous, and judicious manner, and as our statesmen become alive to the necessity of fostering, without extremely protecting, our metallurgical indus tries, mines and furnaces will gradually prosper, and so develop as to become a tower of strength to our agricultural, manufacturing, and mercantile interests. The fact that our past experience does not generally justify such glowing anticipations makes one all the more anxious to put on record the history of a successful mine, such as the Silver Islet has, on the whole, been. My connection with its discovery and early development was a very intimate one, and I propose in this paper to sketch its history and character, and sum up the amount of silver it has so far yielded. An additional reason for the appearance of this paper is that the Transactions of the Institute contain only a few references to the Silver Islet Mine. Although this mine is reported successful, we have, of course, no guarantee that it will not fall a victim to the same influences which have

Jan 1, 1880

By E. I. Larsen, E. F. Swazy, F. R. Hensel

HIGH strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. COPPER POWDERS The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975°C. and repressing. The size of the finished compacts was ¼ by ¾ by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. [ ] In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result frequently in expansion during sintering for the type of powder used. Fig 5. indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c. c., affect only slightly the pressure required to obtain a

Jan 1, 1945

Discussion of the paper of Archer E. Wheeler and Milo W. Krejci, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1831 to 1880. BRADLEY STOUGHTON, New York, N. Y.:-I would like to ask Mr. Krejci whether they have tried mixing coke dust with the lime in those converters and, if so, if any advantage has been found. It has been a very great advantage in the steel converters where coke dust has been mixed with the lime near the tuyeres. Of course the agent that causes the corrosion at that point is oxide of iron, and coke seems to prevent the formation of the oxide of iron and so protect the tuyeres. It would be interesting to know if it had the same effect in the copper converters. MILO W. KREJCI:-We have never tried it here. At Anaconda the tuyere section was formerly put in by mixing magnesite with tar and ramming that into the tuyere section, but they have abandoned that. Might I ask how you would apply the coke dust? How get it into the tuyere section ? How hold it there ? BRADLEY STOUGHTON :-The coke dust is mixed with silica and clay and then rammed in and burned. I suppose in your converters it would be mixed with the magnetite or magnesite and then agglomerated with the material in place. MILO W. KREJCI:-We never tried it here. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-I would like to ask how thick this deposit of magnetite is on the lining. How thick a layer would be practical ? MILO W. KREJCI:-About 21 in. would be sufficient. SOLOMON LE FEVRE, Mineville, N. Y.:-I was interested to hear of the use of magnetite in connection with the copper smelter. I am interested in the mining of magnetite, but was not aware that it had been used at all' by the copper metallurgists.

Jan 11, 1913

By Charles R. Fettke

In the present day manufacture of glass nearly pure quartz sands are used almost exclusively as the source of the silica, which is the major constituent of all common varieties of glass. Ordinary soda-lime, such as bottle, common tableware, plate, and window glasses, contains from 65 to 75 per cent. of silica. Occurrence Glass sands occur in nature either in the form of loose, unconsolidated sediments or in deposits in which the individual grains have been more or less thoroughly bound together by some cementing agent so as to form sandstones. While deposits of sand and sandstones occur both widely and abundantly distributed, deposits that are sufficiently free from other constituents than quartz grains, so that they can be employed in the manufacture of the better grades of glass, are, comparatively speaking, of rare occurrence. The major portion of the glass sand produced in the United States comes from sandstones. In order to be suitable for glass sand, they should be rather friable. The rock should break down readily along the cementing material between the grains and should not break across the grains rather than along the bond. Some of the sandstones used are so friable that only light shots of slow-burning dynamite are necessary to disintegrate them sufficiently for hydraulic mining, while others have to be passed through crushers in order to disintegrate the rock into its individual grains. MINERALOGICAL COMPOSITION An ideal glass sand is made up entirely of grains of the mineral quartz free from inclusions of foreign substances. Sands containing 100 per cent. silica, however, are not found in nature, although some very nearly approach this composition.

Jan 1, 1926

The University of Colorado, Boulder, Colo. The University has published a volume, "Geology and Natura Resources of Colorado," by R D George The price is $2 and the volume may be had from the Campus Bookstore, University of Colorado, Boulder, Colorado.

Jan 1, 1933

By Conrad W. Stellar, John L. Paynich

Design/Build concept that provides for earliest possible completion and lowest cost is presented. Elements of the program include: joint cooperation between owner, designer and builder; schedule construction sequence; and a line budget. Benefits over lump sum contracts are reviewed.

Jan 1, 1979

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges'' as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By A. L. Holley

IT has been customary at our opening sessions, for the presiding officer to address you on the general development of one or another of our several professions, or upon some important feature of Mining or Metallurgical Engineering. It is somewhat embarrassing to his successor that our former President, Dr. Raymond, expert as he is in every one of these professions, has been accustomed to keep them all, in their turn, prominently before you. In selecting for this occasion a subject necessarily connected with iron and steel, I have thought that a review of these manufactures, with reference to some of their more pressing needs for improvement, will be more timely than a general or statistical paper. I shall endeavor to confine my remarks to a few specific defects of practice and management, and to their equally specific and more or less developed remedies. That serious defects exist ; that they must be remedied ; that the manufacture is indeed already on the verge of transition, will be generally admitted. But it cannot be revolutionized all at once, however desirable the technical results might be, for that would bankrupt the business at large. We cannot afford to pull down and rebuild all our blast-furnaces that do not make a ton of pig iron with 25 cwt. of fuel ; nor to replace all our hand-puddling furnaces with revolving ones, even if we could select the best revolver. Although the soft steels promise to supplant iron for most structural purposes, there are neither money nor present market to warrant all at once replacing our iron works, or half of them, with steel works. Since, then, these manufactures can neither standstill nor be suddenly metamorphosed, their managers are saying to one another " We must feel our way into larger development ; we must work gradually into better practice; we must improve a little at a time." * President's address on the opening of the Cleveland meeting.

Jan 1, 1876

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed' in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably, even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1951

By S. R. Goodman, Hsun Hu

The rolling texture of an 18-8 stainless steel (Type 304L or 304) has been found to change gradu -allv from the (110)[112] brass type to the (123)[412] copper type as the rolling temperature increases from 200° to 800°C. This texture transition is accompanied by a change in the stacking-fault frequencv or probability, similar to those found pre- In a series of previous publications, it was shown that the rolling texture of high-purity silver changes gradually from the brass type to the copper type with increasing temperature of deformati~n. A similar temperature dependence of rolling texture transition was found in electrolytic copper3—by lowering the temperature of deformation, the normally observed rolling texture of copper changed gradually viously in nonferrous fcc metals—the stacking-fault frequency decreases rapidly with the formation of the copper type texture. These results strongly indicate that the temperature dependence of copper type == brass type texture transition and its correlation with stacking-fault frequency is a general phenomenon in fcc lattices. to the brass type.* In both of these metals, the

Jan 1, 1964