Search Documents

By M. M. Leighton

THE engineers of Illinois have been submitting to the State Geological Survey an increasing number of requests for advice on their geological problems, including landslides, unequal settling of fills, laying pavements across peat bogs, shattering and heaving of pavement by frost action, etc. The authors discussed the behavior of landslides, their effects, their causes, a tentative classification, and remedial measures. In the latter connection the efficacy of drainage and how it should be handled in order to be most effective was considered. The principles and efficacy of other remedial measures, such as subsurface blasting, rock anchoring, installation of wood, concrete or steel piling, construction of retaining walls, construction of cribbing and reduction of slope were also discussed. Attention was also given to the matter of applying geological knowledge to avoid undesirable highway locations, and a specific example was cited.

Jan 1, 1929

By E. I. Larsen, E. F. Swazy, F. R. Hensel

EXPERIENCE has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. TEST MATERIALS Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It was found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended on the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as one eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from. 900°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal composition was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical properties and certain bearing properties of this alloy are described in the present paper. PREPARATION OF COMPACTS Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition: 25 per cent nickel; 7 silicon; 3 phosphorus; 64 copper. This alloy is brittle in. the cast condition and can be readily powdered. SINTERING PROCEDURE The blended powders were pressed at 25 to 40 tons per sq. in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By Edward H. Robie

In late November and early December a considerable portion of our time was devoted to obtaining a business manager for Institute headquarters. The advisability of creating such a position was suggested in 1949 in the report of the Johnson committee. In that year, however, the Institute had a deficit of $72,000 so every effort was made to minimize expense. At that time most of the duties that normally would be assumed by a business manager were given to Newell Appleton who became office manager, convention manager, purchasing agent, and assistant to the secretary. So many responsibilities were his that he could not devote the necessary time to all of the many things that needed attention. H. H. Vasoll, representing a firm that made a study of Institute head office procedures early last fall, made a recommendation that "a business manager and controller from outside the present organization" be obtained, who would supervise the work of accounting, addressograph, purchasing, book and journal orders, filing, and mailing depts. He further recommended that Mr. Appleton be made administrative secretary, in which position he would act as head of an "Institute Activities Dept." He would devote his time to convention planning, meeting arrangements, travel accommodations, membership control and promotion, and public relations, and would assist the Secretary on special problems. Thus, Mr. Appleton retains some of his former responsibilities and will take more of the load off our shoulders in the conduct of affairs at Institute headquarters. The rest of his former work will be in the province of the newly created "Business Office Dept." Peter J. Apol is the man finally selected for the post of business manager. He is a young man of 32, a native Michigander and a graduate of the University of Michigan where he received a B.S. degree in business administration in 1940. He then spent three years in the Navy and has the rank of Lieutenant in the U. S. Naval Reserve. Three more years were spent in the U. S. Maritime Service as chief purser, and another year as chief paymaster for the Pope & Talbot Steamship Co. The past four years have been spent as head of the Greenland Construction Co., Greenland, N. H., chiefly engaged in building construction. Mr. Apol will endeavor to increase the efficiency of Institute headquarters operations and remove all possible causes for complaints of individual members. He will coordinate as seems advisable the work of various departments and install such modern business office machinery as seems applicable to our needs.

Jan 1, 1952

By J. F. Butler

The degree and type of carbide dispersion resulting from changes in the cooling rate from austenite determine the amount of carbon remaining in solution after slow cooling- from a subsequent subcritical annealing treatment. A difjusion model has been proposecl to explain the effect of carbide dispersion on the amount of carbon retained in solution and the amount of carbon in solution has been related to the degree of carbon strain aging. COTTRELL and Leak' have shown that the rate of strain aging in low-carbon steels is dependent upon the amount of carbon and nitrogen in solution. Carbon can be effectively removed from solution as Fe , C by quench aging at temperatures of 200" C or lower; however, the relatively higher solubility of nitrogen at these temperatures prevents sufficient removal of nitrogen as iron nitrides. For this reason, nitrogen in solution has been considered the major cause of strain aging in rimming grades of commercial low-carbon steels. Nitrogen can be effectively removed from solution and nonaging steel produced through the addition of aluminum to form the stable nitride, AlN; however, the aluminum also causes deoxidation resulting in a killed steel. III an attempt to produce a rimmed steel which was also nonaging, Morgan and Shyne 2 investigated tile strain-aging properties of low-carban steels containing boron and found that strain aging was suplx-essed in steels containing as little as 0.007 pet B. The original purpose of this investigation was to determine the mechanism of strain-aging suppression by boron. Early in the study, the function of boron was discovered to be much like that of aluminum in that the formation of a nitride, BN, removed the nitrogen from solution.' However, during the course of the investigation, an effect of heat treatment upon the strain-aging properties and the amount of carbon in solution was found which could be related to the microstructure of the steel. The purpose of this paper is to examine these relationships among heat treatment, microstructure, carbon in solution, and strain aging in steels where nondetectable amounts of nitrogen are present in solution. EXPERIMENTAL PROCEDURE The investigation was carried out using 0.030 in. by 12. in wire specimens which had been cold swaged and drawn to the final diameter. Table I lists the compositions of the low-carbon steels used. Those with 'V' designations were vacuum melted and cast; the alloys designated 'AISI' were prepared from high-purity iron obtained from the American

Jan 1, 1962

By R. E. Crockett

MAGNETITE mining and milling in the Eastern States was at capacity during 1940, owing to the heavy industrial, defense, and war demand, coupled temporarily with the almost total stoppage of imports of foreign ores other than those under American ownership. In New York State the active mines were those operated by the Republic Steel Corp. at Mineville and Lyon Mountain. Republic's new concentrating mill at Port Henry, handling the Mineville ores, went into production about the first of April. Other large magnetite deposits in New York are currently being prospected and studied and may be under development in the near future. In New Jersey the Mt. Hope and

Jan 1, 1941

By JOHN A. MALONEY

AS noted in the February issue of MINING AND METALLURGY, an advisory committee to the Museum of Science and Industry of Chicago was authorized by the Institute's Board of Directors, with W. R. Wright of Chicago, former Director of the Institute, as chairman. Since that time the committee has been undergoing organization, and held its initial meeting at the Museum offices in Chicago on April 11 and 12. Functioning as consultants to the Geology and Mineral Industries branch of this new institution, the advisory committee is aiding in building an exhibit which will tell the story of geology, mining, and metallurgy to millions of visitors a year. Although patterned to some extent

Jan 1, 1932

Those familiar with the war in France at first hand know that in these last two years the weight of the suffering has fallen upon the families of the well-to-do classes; those who before the war lived in comparative ease and comfort, with every prospect of educating their children as their parents and grandparents had been. Thousands of the men in these families have been killed, "officiers d'élite," and the small pensions accorded the widows permit them only to house and feed their children HELÈNE JOURNÈS. and give them a common-school education. The pension for a lieutenant's widow is $245 a year; for 'a captain's, $345; for a colonel's $575; and so on. At present, it requires three francs a day to provide food for one person in cities, and conditions are not improving. The American Ouvroir Funds, 681 Fifth Ave., New York City, has tried for nearly two years to have individual Americans give individual children a "bourse," or purse, as it is called, of from $150 to $250 a year, so that they may enter such educational institutions as the Lycées, the Polytechnique, Beaux Arts, St. Cyr, etc. The war relief societies of these military schools furnish photographs and histories of children under their care and on their lists.

Jan 12, 1918

By Volker Ruth

DURING an experimental investigation of the Kirken dall effect in the Ag-Au system, cracks along grain boundaries in connection with a shift of adjoining crys tallites are observed on the gold-rich side of the couple. Also on the gold-rich side the formation of a zone of small protrusions is found.' The growth law of the width of this zone indicates that the protrusion formation is a secondary effect of diffusion. The protrusions are not found within a distance of approximately 60 from a grain boundary. Unaffected regions along grain boundaries were also observed by Doherty and Davis during precipitation of vacancies in aluminum2 and by Wyon and Lacombe during precipitation of iron in aluminum.3 Thus we may suppose that we have an effect analogous to precipitation in which the crystal tends to maintain its equilibrium vacancy concentration by transporting excess atoms to the surface. At an early stage (i.e., before sintering has influenced the shape of the protrusions) the protrusions have similar shapes (three sided pyramids and roof shapes) and similar orientations within a single grain but vary from one grain to another. Further experiments were carried out on cylindrical Au-Ag single crystal couples. During the weld-

Jan 1, 1963

By D. M. Jamieson, M. P. Pearse, E. R. A. Plumstead

In 1948 the shaft sinking record in the Republic of South Africa was held by the Van Dyk Consolidated Mines Ltd. for a ventilation shaft with a footage of 461 ft sunk during the month of August 1941. This record remained for some ten years; but in the ensuing nine years it was broken no less than 13 times. Table I gives shaft sinking records throughout the world for the 21 years, 1940 to 1960. History shows that the wide, deep, timbered rectangular shaft had passed its peak of popularity by 1948, although it still had a great deal to commend it, both from the sinking and operational points of view. In sinking, it is easy to clean manually, and water can be handled by bailing when wet ground has to be negotiated; its shape also lends itself to equipping concurrently with sinking. In operation it provides the most convenient "in line" hoisting arrangement, and if the ventilation requirements so demand, it offers the simplest solution in that it can be divided into upcast and downcast sections. Furthermore, in the case of a multi-level mine, the shaft compartments can be reduced conveniently if the full area of the shaft is not required to serve all levels.

Jan 4, 1963

By C. E. Webber

THE economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro-carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,5 who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40° to 200°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33° to 180°F. and from 100 to 5000 lb. per sq. inch.

Jan 1, 1940

By J. S. Ross

OIL-FIELD waters enter into many underground problems with which the petroleum engineer has to deal. Whether the problem is one of infiltration or natural encroachment, it is always desirable to determine the source of the water before commencing repair or remedial work. The usual mechanical tests for determining the source of extraneous water in wells are slow and expensive. An excellent means for the identification of oil-field waters may be afforded by their chemical characteristics when the chemical character of waters from the various sands has been established, by careful sampling and analysis cautiously interpreted. In the Salt Creek field, Wyoming, a fairly high degree of efficiency has been attained in the controlof field operations by utilizing the information afforded by the analysis. All of the operating companies appreciate this means of identifying waters, with the result that water-sampling has become general practice. Most of the chemical work dealing with Salt Creek waters has been done since the laboratories of the Midwest Refining Co. and the U. S. Geological Survey, were established in the field; the former in 1922, the latter in 1924. A spirit of cooperation has existed between the company and the government personnel by which many of the data for this paper were made available.

Jan 1, 1928

By N. R. Tipman, G. E. Agar, L. Paré

The flotation chemistry of the commercial INCO matte separation process was investigated. The slow cooling of Bessemer converter matte forms discrete phases of Cu2S and Ni3S2 and a Cu-Ni alloy. After magnetically removing the alloy, the Cu2S and Ni3S2 are separated by flotation at pH 12.4 (saturated lime) using diphenyl guanidine (DPG) as both collector and frother. DPG has been used exclusively in this flotation process because of its unusual selectivity for copper minerals. The surface product resulting from chemisorption of DPG onto theCu2S was identified as the double salt CU(DPG)2SO4.CU(DPG)2(OH)2. The adsorption followed Langmuir behaviour up to a monolayer coverage. In the absence of DPG, the rapid adsorption of oxygen by Cu2S in flotation pulps was observed. The surface product was identified as the insoluble basic copper sulfate CuS04.3Cu(0H)2 with the production of sulfate ion. In the presence of DPG, the oxidation reaction appears to be suppressed. The frothing properties of DPG and commercial frothers were compared. DPG is not a powerful frother. Batch flotation tests confirmed that DPG is a highly selective collector when compared to most sulfhydryl collectors.

Jan 1, 1976

By Tsuyoshi Kawahara

INTRODUCTION A medium sized mine like the Mamut is not considered a standard size porphyry copper mine. If the infrastructure such as roads, bridges, port facilities, power supply, etc. is inadequate, construction cost per ton of copper produced will be unavoidably high. At the Mamut mine, all efforts had been concentrated to minimize construction cost and overcome an adverse natural environment. Consequently, it was inevitable that the amount of equipment and other arrangements were far from ideal. Some of the construction work was carried out by Japanese contractors, but most was done by local contractors, especially the buildings, installation of machines, roads, and tailings disposal dam, etc. All construction works, including a test run of an 18 000 t/d capacity mill, were completed in September 1975. The total development cost was about 100 million including interest converted into principal during the construction period. HISTORY The Mamut copper mineralization was discovered in mid-1965 by the United Nations' Labuk Valley Project. Following this discovery, further exploratory works, including geochemical survey, pitting, and shallow diamond drilling, which were carried out by the Geological Survey of Malaysia, revealed the existence of a disseminated copper mineralization of porphyry type. In July 1968, I.P. survey and deep-hole diamond drilling were

Jan 1, 1976

By E. Goldin, H. J. Juretschke

THE electrical properties of porous conductors have been studied ever since such materials, usually prepared by pressing and sintering of metallic powders, obtained practical importance. In most cases, however, the results have not been easy to interpret because of the great number of independent variables such as powder size, pressure, pressing rate and temperature, subsequent thermal history, porosity, and so on, which enter into the fabrication of industrially desirable materials. In recent years an interpretation of these properties has become of interest because the electrical properties of many new substances, prepared as fine powders by crystallization from the vapor phase or by reactions in the solid state at high temperatures, have to be determined on porous samples formed from the powder. Since theoretically significant information must refer to the fully dense state of the material, it is important to relate the electrical properties measured on such porous samples to those expected for a sample of 100 per cent density. A simple theory for the porosity dependence of the electrical conductivity and the Hall effect was recently proposed by Juretschke, Landauer, and Swanson.' Their model, assuming a distribution of pores of equal size and shape, sufficiently far apart so that each pore is embedded in a region of uni-

Jan 1, 1959

By Carl J. McHargue

Rods of 99.99 + pct Al which had initial orientatzons of <001>, <118>, <115>, <111>, and random were swaged at room temperature. Changes in orientation as a function of deformation were studied on axis distribution charts. The <001> orientation appeared to be relatively stable due to the inhomogeneity of the deformation process. near the <100> zone were quickly reoriented towards <001>. Orientations on the <110> zone between <118> and <115> appeared to be stable to reductions of about 50 pct, then were reoriented toward <001>. At very high reductzotzs. movement away from the <111> orientation was observed. the requirement that a circular cross section be maintained. In addition to these mechanical factors, there are grain-boundary effects in poly crystalline materials which are not yet understood. Hartmann and Macherauch conclude, for example, that multiple slip occurs for all orientations in fine-grained aluminum and copper and that the choice of operative slip systems has no simple relationship to orientation.? Many investigators have attempted to avoid problems of interpretation caused by an initial texture by treating the starting material to obtain as ran- IT has been generally accepted that the deformation texture obtained at high reductions, e.g. 90 pct, will not be noticeably affected by a prior texture; whereas, that obtained at reductions of 40 to 50 pct may be significantly influenced by the specimen history.&apos; Some recent studies, however, have been interpreted as showing that an initial texture strongly influenced the deformation textures in rods at reductions greater than 90 pct. Freda and Cullity suggested that the <001> texture in a heavily cold-worked copper rod was due to a <001> texture in the original casting. McHargue, Jetter? and Ogle concluded that the <001> component in an aluminum rod extruded at liquid nitrogen temperature was remanent from a <001> texture in the cast extrusion billet.3 Most of the published work on the effect of initial orientation on deformation textures has been for cold-rolled or compressed single crystals,4-6 The primary interest in these studies was to examine various orientations with regard to their stability under flow? thus determining the possibility of such orientations being stable end orientations. There appears to be no published studies on the effect of initial orientation on fiber textures in polycrystalline specimens. A recent study, however, is concerned with the reorientation of individual grains in polycrystalline specimens pulled in tension.? Although the reorientation of single crystals loaded in simple tension is well known, the movements in the forming of wires and rods would be expected to be different due to the circular array of radial-compressive stresses exerted by the die walls or the rolls, and to

Jan 1, 1962

By L. V. Wade

US Bureau of Mines efforts under longwall research programs to develop the capability to predict support requirements for longwall/shortwall support systems are discussed. Ground control studies are being conducted in conjunction with several longwall/shortwall demonstration projects. Geologic, support performance, and strata behavior are being documented on these projects. A hypothesis is presented for the prediction of support requirements.

Jan 1, 1979

By Tom Bilson

TO recover the remaining ore tonnages along the south side of the Inspiration orebody, the company began open-pit operations in early 1948 in addition to underground mining. Due to the differences in elevation between the orebody and the existing ore handling and treating plants, the truck haulage operation is up hill. Road grades were established at 7 pct maximum.

Jan 8, 1951

By Douglas M. Dwosh

Inland Steel Coal Co.&apos;s system of applying a gypsum/fiberglass rib and roof sealant with standard rock dusting equipment will be outlined. The criteria for use included acceptability of results, flexibility of equipment, ease of application, and economics. Material is conveyed dry until the gypsum, fiberglass, and water are combined at the discharge end of the rock dust hose.

Jan 1, 1978

By R. H. Goodman, C. A. Brown

The development of improved new models of spiral concentrators is reviewed. The mechanics of separation of spiral concentrators are stated, including the effects of operating parameters. Some of the traditional areas of spiral application are described, together with examples of new applications such as treatment of fine alluvials and tailings, separation of liberated minerals at coarse sizes, and fine coal recovery.

Jan 1, 1986

By L. K. Borrett ond C. S. Yusi

The authors have made extensive use of a modern field of mathematics, topology, to give a new approach to the study of sintering. They present a topological model for the sinter body and the void space, and establish a relationship between them. However, in an interdisciplinary paper of this nature it is important that the material be presented, insofar as possible, in

Jan 1, 1967