Search Documents

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

With the coming of the month of 'October the various sections are beginning active work for the winter. The Colorado, Washington, Montana, and New York Sections are all doing good work in raising funds for the hospital bed at Rheims which is to be a memorial to the members of the A. I. M. E. who gave their lives in the great war. We hope that all the other sections will begin to work with this object in view and will make even a better record than they did with the Belgian Relief Fund. It was with much regret that the President, Mrs. James F. Kemp, and the Secretary, Mrs. Sidney J. Jennings, were obliged to forego the pleasure of attending the Chicago meeting in September. They were, however, ably represented by Mrs. Arthur S. Dwight who gave an informal talk after which was formed the Illinois Section, which has our best wishes for all success-" Over the top and the best of luck!"

Jan 11, 1919

By Ross W. Smith, Mine-Yun Hwang

Many studies have been made of the microflotation of quartz (de Bruyn, 1955; Fuerstenau, 1957; Somasundaran, 1964; Smith, 1973; Fuerstenau, 1976; and Smith and Akhtar, 1976) and alumina (Somasundaran, 1964; Smith and Akhtar, 1976; Fuerstenau and Palmer, 1976; Fuerstenau and Akhtar, 1976; Fuerstenau and Yamada, 1963; Modi and Fuerstenau, 1960) using various anionic and cationic heteropolar hydrocarbon surfactants as collectors. A few studies have been made on these materials using amphoteric hydrocarbon collectors (Wrobel 1969 and 1970; Smith. Haddenham, and Schroeder, 1973; Gupta and Smith, 1975) and only a few studies have been made on the use of fluorocarbon surfactants as flotation collectors Cooke and Talbot, 1955; Somasundaran and Kulkami, 1973). The present investigation compares microflotation response of the two minerals in hydrocarbon and fluorocarbon collector systems of the anionic, cationic, and amphoteric types. An attempt is made to relate flotation response of the minerals to their electrokinetic behavior and the pKa values of the collectors.

Jan 1, 1981

By J. J. Bean

Concentrating mixed sulfide-oxide copper ores by the leach-precipitation-flotation method is an old operation at the Miami Copper Co. The idea was conceived and the method developed at Miami by F. W. Maclennan and Harmon Keyes during the years 1929 to 1934, and it was these men who gave the term LPF to this process. Miami at that time had considerable reserves of mixed sulfide-oxide ore.* In the development of a suitable treatment method, it was natural that leaching of the oxides with acid and the precipita¬tion of copper from the resulting copper sulfate solution by iron was investigated. The separation… • The term oxide as used in this article includes the copper oxides, carbonates, and silicates.

Jan 12, 1960

By Tuncel M. Yegulalp, Peter G. Zambas

In planning an underground room-and-pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1974

By J. D. Dixon

Procedures are given for calculating stresses in underground tunnel supports which accounts both for the structural behavior of the support and that of the adjacent rock mass. Stresses in the support are caused by service loads and rock reactions. Service loads are due to rock pressures, hydrostatic and hydraulic pressures, selfweight of the support, or other utilitarian-type loads. Rock reactions, equal and opposite those in the support, are due to the deformational interaction that results as service loads deform the tunnel support against the adjacent rock mass. The procedures developed for solving this problem are an application of matrix structural analysis. The principles involved in this method allow for the consideration of the deformable characteristics of most tunnel support systems and an iterative solution procedure is applied to determine the areas of support-rock interaction. Numerical results of example problems are given.

Jan 1, 1972

By Grant Buma

The purpose of this paper is to present arguments and evidence that there are natural processes at work which tend to minimize the impact of solution mining on the environment. The contaminants have two sources. First are elements which were present in the roll-front deposit in insoluble compounds, for example, uranium in uraninite and coffinite, molybdenum, arsenic, iron, cobalt, nickel, etc. in sulfide minerals, vanadium in micas and clays, etc. Second are elements introduced by the leach liquor. Precipitation of reduced compounds, scavenging of heavy elements and absorption by quartz and clays, can all reduce the amount of heavy elements in solution. If a roll can be demonstrated to be actively precipitating uranium and heavy metal elements, then the presence of precipitants (pyrite and carbon) can be assumed. Criteria for recognizing an active roll are described.

Jan 1, 1979

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study con firm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity.

Jan 7, 1950

By Byron W. Cheever

At the meeting of the Institute held in St. Louis, in October, 1886 (Transactions, xv., 448), I presented a paper upon the above subject. From the well-known action of certain solvents on phosphide and phosphate of iron, the conclusion was then reached, founded on analyses, that phosphide and phosphate of iron must be present in all iron. But this conclusion was based upon the reactions obtained in the analyses of iron phosphide and phosphate, in which the phosphorus existed in conditions different from those found in commercial iron. In the former, the phosphorus is concentrated ; in the latter, diffused. This fact left a reasonable ground for doubting the existence of phosphoric acid in commercial irons. Some direct method was therefore sought which would prove its presence. After investigating the subject for some time, I came to

Jan 1, 1888

By S. R. B. Cooke, R. O. Huch, C. S. Chang

IN the flotation of iron ores laurylamine derivatives have been used for considerable time.12 To effect satisfactory separation of the gangue, predominantly silica, from the iron oxide minerals, the addition of specific depressants for the iron oxides has been found necessary. Starches and starch products have been used for this purpose. 3 There is, however, very little published information on the effects of these materials and other variables on this process. In some cases it has been found that prior acid scrubbing and desliming are essential, 4 and depending upon the efficiency of the subsequent washing step, there will be accompanying changes in pH. It was the object of this investigation to test and observe the effects of the above factor as well as to examine and compare the action of various starches and starch products.

Jan 12, 1953

B. R. Coil (Electrical Installations at the Miami Mine are Cheaper with Flexible Cable, P. 356) was born in Higginsville, Mo., and attended McKinley High School and Missouri School of Mines. He received a B.S. in mining engineering. Mr. Coil has worked for the Braden Copper Co., Rancagua, Chile as junior engineer and foreman. He was employed by Miami Copper Co. as a jigger boss, shift boss, development engineer and mine foreman. He worked as mine superintendent and general superintendent of the Castle Dome Copper Company, Inc. Mr. Coil may be reached at Box 100, Miami, Ariz. He is an AIME Member. Mr. C. R. Ross was co-author with Mr. Coil in the preparation of this paper. His paper covers the present installation of electrical equipment in block caving stopes along with background data. In this paper he has given one solution to wiring problems in heavy stopes.

Jan 1, 1952

By E. F. Evoy

The uranium deposit of Gunnar Mines Ltd. is on south shore of Crackingstone Peninsula in the Beaverlodge area of northern Saskatchewan. The property spans St. Mary's Channel, a narrow waterway separating the mainland from a group of islands in Lake Athabasca. The mine property, consisting of 12 claims and 7 fractions, was staked in July 1952 by A. O. Zeemel and W. J. Blair. Diamond drilling commenced in the fall of that year and continued until the spring of 1954. In that interval, some 70,000 ft of drilling outlined an orebody plunging from the surface south-ward to a depth of 1000 ft below the shore of St. Mary's Channel. The last 9000 ft of drilling was through lake ice, and when this was interrupted by spring breakup, sufficient ore reserves had been established to warrant the present operation. Surface drilling was therefore terminated.

May 1, 1956

Wabush Mines is the largest single supplier of iron ore to the Canadian steel industry, with 42% of its 6 million tpy of iron ore production going to the company's two Canadian owners-The Steel Co. of Canada and Dominion Foundries and Steel Ltd. Six other companies hold interests in Wabush Iron Co. Ltd. These are Lykes-Youngstown, Inland Steel Co., Intrerlake Steel Corp., Wheeling-Pittsburgh Steel Co., Finsider of Italy and Pickands Mather & Co. Field work on Wabush began in mid-1957 when a long-range program of economic, geologic, and metallurgical investigations started. This work was followed in 1959 by the construction of a temporary camp and a 700-tpd pilot plant. At the same time, work was also started on a 38-mi railway connection to Ross Bay, Newfoundland.

Jan 1, 1970

By E. E. Carpenter

(San Francisco Meeting, September, 1915) BELIEVING that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than trucks, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. ,

Jan 6, 1915

By E. S. Porter

The techniques of particle-size measurement are of particular importance in the manufacture of portland cement. A range of sizes, from a close approximation to Fred C. Bond's "theoretical infinite" (represented by raw material in the quarry) to particles smaller than one micron is represented in the process. Moreover, similar size-reduction operations are performed on both natural and synthetic materials, the former relatively inactive in water and the latter quite reactive. This means that aqueous sedimentation systems for particle-size analysis are applicable only to some of the materials involved in the process. A brief review of the process should be useful to place the measurement techniques described here in perspective. (Fig.l) Raw materials are quarried, crushed and transported to storage at a maximum size usually of a few inches. Typical materials are limestone and clay or shale, with small amounts of other materials used to adjust the plant mix to the concentration of lime, silica, alumina and iron oxide required.

Jan 6, 1962

By B. H. Bergstrom, W. Mitchell, C. L. Sollenberger

D. W. Fuerstenau (Associate Professor of Metallurgy, Dept. of Mineral Technology, University of California, Berkeley, Calif.) and D. A. Sullivan, Jr. (with the University of California) — Messrs. Bergstrom, Sollenberger and Mitchell have shown in two excellent papers that the energy per unit mass required for the breaking of spheres is inversely proportional to the size modulus of the fragments of the broken spheres. They found that the fragments of spheres broken within a steel enclosure were finer than those produced by breaking spheres encased in gelatin. This results from utilization of part of the strain energy at fracture for secondary breakage. For spheres not encased in gelatin, these authors found that after fracture the fragments of the spheres possess kinetic energy amounting to 45% of the strain energy needed for initial fracture. Breakage of a sphere in gelatin results in waste of this kinetic energy, whereas breakage inside the steel container makes use of this kinetic energy for further size

Jan 1, 1962

By C. T. Sheeran, J. C. Franklin

A commercially available microprocessor-based system capable of monitoring 512 channels has been interfaced with monitors for radon, working level, air velocity, and fan power. The basic system utilizes both 280 and 8080 microprocessors in a desktop central processing unit (CPU). CPU hardware includes keyboard, video display (CRT), and disk drive; a printer is used to keep permanent data records. Signals from all channels are transmitted to the computer in digital form where they are processed for alarm status. Software developed for the system allows for audiovisual alarms in the event of low and high readings, rate change, change of state, or communica- tion failure. Up to six channels can be continuously displayed on the CRT for current readings. Shift reports and trend logs may be generated to help the ventilation engineer determine average working levels and ventilation effectiveness. Additional software permits the operator to program command sequences which may be used to automatically restart fans after a power outage.

Jan 1, 1982

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at the Institute headquarters during the period Oct. 10; 1916 to Nov. 10, 1916. Edwin C. Bloomfield, Montreal. Roy E. Hoffman, Hannibal Mo. A. H. Collbran, Seoul, Korea. E. C. Harder, Cienfuegos, Cuba. Eugene Coste, Calgary, Canada. B. Jaeger, London, England. Fred Crabtree, Pittsburgh, Pa. Herbert H. Lauer, Philadelphia, Pa. P. St. John Dixon, London, England. Frank C. Laurie, Los Angeles, Cal. A. E. Drucker, London, England. 0. T. Lempriere, Melbourne, Australia. F. N. Flynn, Clifton, Ariz. W. C. Phalen, Washington D. C. Justice Grugan, Edwards, N. Y. William H. Rea, Pittsburgh, Pa. Fred A. Hale, Jr., Goodsprings, Nev. Thor Warner, Kingman, Ariz. P. S. Haury, Seoul, Korea. Arthur P. Allen has resigned his position with the Calumet & Hecla and is now connected with the Highland Mining Co., Ashcroft, B. C., Canada. H. Foster Bain, editor of the Mining Magazine of London, has resigned his position.

Jan 12, 1916

By John Birkinbine

Mr. Neilson was born Aug. 12, 1842, at Philadelphia, Pa., where he died Dec. 30, 1906. His business career began with his graduation, in the class of 1862, from the Polytechnic College of the State of Pennsylvania. For a short time after graduation he was instructor in mathematics at the college, and then became associated with Messrs. Booth & Garrett, chemists, of his native city. In 1867 he was sent to the Adirondack mountains to care for mining interests of the late Jay Cooke, and spent about three years there, operating the forges at Elizabethtown, Essex county, N. Y. He also prepared an interesting monograph on Catalan forges and their operations. In 1868 he published a chart showing the material progress of the United States, and the cost of certain staple products during a series of years, which is believed to be the first of its kind issued in this country. In 1870 he made a trip to the Pacific Coast, prior to entering the service of the Pennsylvania Steel Company.

Jan 1, 1908