Search Documents

By Frank Foote

PRECISION lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and mag-nesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold sys-tem, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported.

Jan 1, 1940

By K. Robert Dorman, F. Michael Jenkins

The occurrence of rock bursts in deep metal/nonmetal mines presents a major hazard to their safe and economical operation. As part of a Bureau of Mines program to reduce rock bursts in deep vein mining, a project was conducted in the Coeur d'Alene Mining District of Idaho to evaluate and demonstrate the mining of a destressed sill pillar using undercut-and-fill methods. A 50-ft sill pillar in a burst-prone area was preconditioned by drilling and blasting vertical holes in the ore. After raises were driven through the destressed pillar to the level above, it was mined by the undercut-and-fill method. The conclusion from this demonstration is that the combination of ore preconditioning and underhand mining resulted in greatly improved rock burst and ground control, allowing safe and efficient mining of a potentially hazardous, burst-prone pillar.

Jan 1, 1984

By Peter G. Chamberlain

Many mining engineers considering in place leaching for the first time are uncertain as to how to evaluate ore bodies for potential leachability. Evidence presented in this report emphasizes the critical role of permeability in such evaluations. Whether an engineer is considering leaching "tight" formations typified by the porphyry copper deposits of the southwest or the permeable uraniferous sandstones of Texas and Wyoming, permeability measurements are the keystone of any testing program. Permeability tests range from cheap and easy to highly expensive and sophisticated operations. Constant head, variable head, and pumping tests all have application in evaluating ore bodies for in-place leaching. Costs of these tests will not unduly deflate the pocketbooks of most mining companies. The basic procedures for selecting and running these field tests--including preparing suitable wells--are reviewed for the benefit of newcomers to in-place leaching.

Jan 1, 1979

By W. V. Vietti

Actual field data from several wells are used to illustrate the application of the method of determining the average density of the fluid column in a flowing oil well in the Yates field, Pecos County, Texas. The depths of the wells in the Yates field vary from 900 to 1700 ft., depending on surface elevation and the location of the wells on structure. Production rates over 8000 bbl. per hour have been determined and many wells are capable of producing 2000 bbl. hourly. Gas-oil ratios are usually below 400 cu. ft. per barrel, but a few wells high on structure have produced over 3000 cu. ft. per barrel. Incidentally, tubing wells has cut these high ratios to as low as 400 cu. ft.' By common agreement of the operators all wells making ratios over 400 cu. ft. will be tubed. Daily production of the field is prorated to 110,000 bbl. from an open-flow potential of 5,000,000 bbl. based on hourly open-flow gages.

Jan 1, 1931

By Eugene Ayres

This study is concerned primarily with a backward look at the projections made in the Report to the President by the President's Materials Policy Commission issued in June 1952. Only a few years have elapsed since the date of this report, but definite statistics available then were often not later than 1947. Today we have figures for the intervening years through 1957-virtually a ten-year span. What, if anything, has happened during this decade that was unexpected or wrongly appraised? In the light of more recent data and trends, will we be justified in modifying the longer-term predictions made in 1952? This study will attempt to answer such questions. Major sources and forms of energy will be considered from the standpoints of ultimately available amounts and the rates of production and demand. Electricity: The PMPC projections were made on the basis of an unexpected growth of about 10 pct per year. This was at a time when some experts in the field were assuming growth rates of not more than 8 pct.

Jan 1, 1960

By Martin Coryell

This coal area, and the coal from a limited portion of it, has been known for a long time. In 1817, McClure prepared a geological map to represent the boundaries, and they are not controverted at the present date. In 1834, Richard C. Taylor made a survey and report on portions of the basin. In 1835, Prof. W. B. Rogers was appointed by the State of Virginia to make a geological survey, and made six annual reports in which this area was included; but the reports and maps were not published. R. C. Taylor's Statistics of Coal, published in 1855, gave to the public the details of exploration and production, to date, very perfectly and completely. Daddorw and Bannan's work, Coal, Iron, and Oil, published in 1866, repeated the details before given, and advanced some vague theories respecting the coal-field, but gave no new facts. Macfarlane's work, Coal Regions of America, published in 1873, under the head of " Triassic Coal," chapter 27, gives what is known from existing publications of the position, geology, and production of the field, making

By Martin Coryell

THIS coal area, and the coal from a limited portion of it, has been known for a long time. In 1817, McClure prepared a geological map to represent the boundaries, and they are not controverted at the present date. In 1834, Richard C. Taylor made a survey and report on portions of the basin. In 1835, Prof. W. B. Rogers was appointed by the State of Virginia to make a geological survey, and made six annual reports in which this area was included; but the re¬ports and maps were not published. R. C. Taylor's Statistics of Coal, published in 1855, gave to the public the details of exploration and production, to date, very perfectly and completely. Daddow and Bannan's work, Coal, Iron, and Oil, published in 1866, repeated the details before given, and advanced some vague theories respecting the coal-field, but gave no new facts. Macfarlane's work, Coal Regions of America, published in 1873, under the head of "Triassic Coal," chapter 27, gives what is known from existing publications of the position, geology, and production of the field, making

Jan 1, 1875

Tars Committee is the result of a desire of the authorities in charge of the publications of the four national engineering societies to co-operate in this matter. The members of the Committee are the following: Charles WarreN Hunt, Secretary of the American Society of Civil Engineers. D. S. Jacobus, Vice-President of the American Society of Mechanical Engineers. Joseph Struthers, Assistant Editor of the American Institute of Mining Engineers. CaRy T. Hutchinson, Chairman of The Editing Committee of the American Institute of Electrical Engineers. This Committee has held several meetings; it seemed advisable, at the outset, to limit its discussions closely to the general subject of abbreviations. Further, it seemed best to formulate a few general rules to be followed in making abbreviations, rather than to compile a list of forms to be recommended. The Committee decided to limit the subject more narrowly by considering only abbreviations to be used in the text, or general reading-matter, arid not those to be used in special matter,

Jan 1, 1905

By John P. Bingham

GRACE mine and mill, owned by Bethlehem-Cuba Iron Mines Co. and operated by Bethlehem Cornwall Corp., are being developed to produce 9600 tons of 42 ½ pct Fe magnetite ore, to yield 5760 tons per day of agglomerated iron concentrates averaging 65 pct Fe. Located about 14 miles south of Reading, the property is ideally situated in relation to good highways and railroad. Three major steel plants, at Bethlehem, Steelton, and Sparrows Point, Md., are about equidistant from the mine. Discovery of the orebody resulted from an airborne magnetometer survey, completed in 1948, con¬sisting of 7000 lineal miles of flight lines spaced one-fourth of a mile apart and extending from the Delaware River on the east to Gettysburg, Pa., on the west. After examining the magnetic maps, Bethlehem's geologists made limited surface traverses over the Grace mine and Warwick area to check the location, and realtors were engaged to purchase the desired properties over and adjacent to the area showing favorable indication of ore.

Jan 1, 1957

By Toshio Kurikami, Charles A. Brockmiller, John E. FitzSimmons

In the manufacture of sulfuric acid from SO2 bearing gases, the presence of mercury vapor in the gases may lead to unacceptably high mercury levels in product acid. Anticipating inception of regulations requiring low mercury acid, St. Joe Minerals Corporation and Toho Zinc Company, Ltd. independently developed new mercury removal technology. The processes may be used individually or in combination, depending upon the mercury content of the SO2 gases and the required mercury level in acid, for efficient control of maximum mercury levels in sulfuric acid. The St. Joe B Process removes mercury from roaster off-gas streams, while Toho’s NAK Process precipitates Hg from concentrated sulfuric acid. The combined process is commercially operated at St. Joe's zinc smelter in Monaca, Pennsylvania, and the NAK Process at Toho’s Chigirishima lead smelter and Onahama zinc roasting plant in Japan. Product acid mercury levels of 0.5 mg/kg are economically achieved.

Jan 1, 1976

By Donald Ingvoldstad, Harold E. Lee

At Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse limerock. While oversize material was crushed through Y4-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity.

Oct 1, 1956

By Wilson D. Michell

THE Magma copper vein trends east-west, dips 70° south, and cuts through a 6000-ft thickness of limestones, quartzites, shale, diabase, and schist. The vein is itself a fault with -a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facilitate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, and mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine.

Jan 1, 1947

By S. F. Turcotte, B. J. Grierson

At the Q. I. T. ilmenite smelter, nine electric furnaces produce titania slag and iron At high power levels, a furnace requires either a slag or an iron tap approximately once an hour, using rail cars as slag receptacles and ladles for iron. The correct scheduling of taps is an important operational tool due to peak power load and operational considerations. Over recent years, large increases in furnace capacity have imposed severe strains on the product handling facilities. This situation results in loss of production when several taps are bunched, because of an in- ability to handle many taps simultaneously. An on-line computer program has been developed to generate schedules for tapping a single furnace. By improved scheduling, this program can en- large the tonnage of each tap and minimize the number of taps, while reducing traffic congestion and unit cost s. Future plans call for extension of this technique to all nine furnaces with addition of a master scheduling program to optimize the overall traffic flow in the smelter aisle.

Jan 1, 1969

By Milton E. Wadsworth

Hydrometallurgical processing of ore deposits by solution mining or in situ techniques requires the interfacing of technologies as diverse as hydrology, geology, chemistry, and rubblization. This synthesis represents one of the main challenges to in situ processing due to the inherent complexity and vocabulary of these well-developed technologies, and to the general lack of appreciation for the depth of knowledge and endeavor in each separate field. No better example of the need for such interfacing of technologies exists than that of solution mining. How well these technologies interface depends upon the size of the operation and its financial capability to use the information and technology available. It is inconceivable that any one individual can optimize each potential contribution alone; consequently, some areas are usually neglected or simply are not fully appreciated. When one examines what must be done at a future date to develop and exploit a remote solution mining system, it becomes obvious that each discipline must effectively communicate the needed background information to make the project a synthesized whole.

Jan 12, 1977

By E. A. Stevens

In a low and gently sloping ridge extending some 1500 ft. southward from Squaw Mt., and now.covered by the buildings, or crossed by the railroads and streets, of a portion of the city of Victor, there is an ancient volcanic vent or crater, which exhibits one of the most interesting phenomena of the great upheaval and volcanic disturbance that built up the hills of the famous Cripple Creek gold-field—of the period when mass was piled on mass to form the mountains and foothills; when fissures and craters opened, and lavas, welling up, overflowed the surface, until, finally cooling, they effectually choked their vents, thus forming many of the ridges that stand out in bold relief, and the dikes that seam the Continent. This particular occurrence, though limited in dimensions, shows in miniature certain stages of the eruptions of Etna and Vesuvius,* Kilauea and Loa; and illustrates what was (with the exception of the penetrating dikes) the closing chapter of the early volcanoes whose emanations have contributed to the

Jan 1, 1901

By Frank C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of trans- porting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion.

Jan 9, 1959

By F. J. Menzer, E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 91,000 tonnes of ore per day and has copper ore reserves estimated to be in excess of one bill ion tonnes. Functional groups within the Geology Department (currently staffed with six professional and two support personnel include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pi t metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct exploration and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1984

It was a brilliant idea that suggested the formation of Local Sections of the Institute. The results in increase of membership and attendance at, annual meetings of the Institute have been very gratifying. Many different plans have been followed by the various Local Sections to interest members in the local meetings. It has been found to be almost necessary that the meetings be preceded by luncheon or dinner at some club or hotel where a suitable assembly room is available for the after meeting. Each Local Section has to work out its own type of meeting to suit its conditions. Like all human affairs, a great deal depends on the leader. Special attention should be paid to the qualifications of the Chairman and Secretary as these two officers have to shoulder most of the responsibility for the success or failure of the Section. They should be chosen, not so much on account of prominence in the profession as for their push and popularity with the local membership. It has been developed that in most Local Sections the meetings should not be more frequent than once a month with a vacation during the summer months.

Jan 7, 1919

Two Canadian mining companies, Noranda Mines, Ltd., and Wright-Hargreaves Mines, Ltd., have agreed to buy $500,000 worth of shares each in Anglo-American Exploration Ltd., controllers of thousands of acres of possible oil-rich land in southern Saskatchewan and Manitoba. Samuel Clarence Nickle, Sr., reported as possible president of the newly formed exploration company, said that $20 million in assets have been accumulated by the firm, mainly in the Williston basin in parts of the Dakotas and Montana, aid extending into Southern Manitoba and most of Saskatchewan. The M. A. Hanna Co. reported a record profit for the seventh consecutive year with total 1951 profit reaching $14,081. The company handled a record 16.8 million tons of iron ore in 1951, compared with 14.9 million tons in 1950. The company is also preparing to open four iron ore mines in the Lake Superior district which are expected to produce more than 5 million tons annually by 1954. The company built two new iron ore concentrating plants at Mesabi range mines in 1951,a with a third plant going into, operations soon.

Jan 1, 1952

THE program for the 126th meeting of the Institute, to be held in San Francisco Sept. 25 to 29, 1922, is being prepared by the General Arrangements Committee of the Local Section and its details are not yet ready for announcement. The program, however, has developed to a sufficient extent to permit members to decide whether they wish to attend or not. Briefly stated, Monday, Sept. 25, will be devoted to technical sessions which will be held at the Engineers Club, and there will be as many sessions as may be required to present the papers available, some of which are listed below. Under the registration fee plan (see July magazine) entertainment expenses during the week in San Fran-cisco will be borne by those in attendance, not by local members alone. Members who expect to attend the San Francisco meeting, but who will not accompany the President's party, will please notify C. H. Fry, Secretary of the San Francisco Section, 625 Market St., San Francisco, Cal., of their intention.

Jan 8, 1922