Search Documents

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By J. L. Lytton, J. E. Dorn, L. A. Shepard

Single aluminum crystals were subjected to creep in simple shear on the (111) planes in the slip direction. The activation energies for creep were calculated from the effect of small abrupt changes in temperature on the creep rate just before and immediately following the temperature change. The results definitely establish the fact that creep of single aluminum crystals occurs by-three unique processes, characterized by thethree distinct and isolatable activation energies: The 35,-500-cal-per-mole activation energy obtained at the highest temperatures was ascribed to a dislocativationtion climb process; the 28,000-cal-per-mole activation-energy process, occurring over the intermediate-temperature range was attributed to a cross-slip mechanism; and it was suggested thot the 3400-cal-per-mole process observed below 400°K may be the Peierls energy. THE most pertinent question regarding the phenomenon of creep in crystalline materials is concerned with the identity of the crystallographic mechanisms of deformation that control the creep rate. For many years slight progress was made in uncovering the basic mechanisms for creep. Over the past 10 years, however, two parallel lines of investigations have contributed to a more definitive understanding of the processes involved in creep. The extensive development and maturing of dislocation theories for deformation of crystalline materials' proved to be of paramount importance for this progress. And second in importance was the replacement of the former prosaic methods of creep testing by new techniques'." which were especially

Jan 1, 1959

By John G. Bartram

The oil business has been relatively quiet in Wyoming during 1934. Only 34 producing wells were completed, 54 dry holes were drilled, and at the end of the year only 30 wells are listed as drilling. Wyoming still has a large reserve of production shut in, mostly in black oil or asphaltic base fields in the northwestern part of the state. The total oil production increased from 11,171,500 bbl. in 1933 to 12,539,470 in 1934, but light oil production continued to decline, and the increase was made by black oil fields. This is partly due to natural decline of light oil fields, especially Salt Creek, Big Muddy and Lost Soldier, but largely because of increased demands for road oil. The Rocky Mountain states spent much money to build and improve roads and a greater amount of road oil was used. The refining of black oil to manufacture road oil produced gasoline as a byproduct that slightly decreased the demand for light oil. The Oregon Basin and Frannie fields, in the Big Horn Basin, moved into second and third places in the list of producing fields in Wyoming because of their increased black oil production, and Big Muddy and Lost Soldier, light oil fields, dropped back. Wyoming stayed close to its allowed production, which was based on the needs of the refiners and purchasers. This activity in black oil resulted in a few more wells in the fields of the Big Horn Basin, but the greatest amount of drilling was in the shallow Osage field in eastern Wyoming. Osage supplies many little topping plants and at the close of 1934 there was not enough oil available there to supply all of them. In the Lost Soldier field and Salt Creek, one major company was rather active in a campaign to deepen, clean out and repair old wells to increase production, and the figures of that work are not included here. Of the light oil fields, Lance Creek promises to be most active during 1935, since the two wells in the recently discovered Sundance sand pool are producing and more wells will he drilled. With wildcatting almost at a standstill, two new oil fields were discovered in Wyoming in 1934. In Albany County, a 75-bbl. oil well was completed on Quealey dome in the Muddy sand (Upper Cretaceous)

Jan 1, 1935

By P. Schwarzkopf, J. H. Brophy, J. Wulff

A constitutional diagram has been proposed for the tantalum-rhenium alloy system. Rhenium dissolved in tantalum up to 48 wt pct, and the maximum solubility of tantalum in rhenium is 5 wt pct. Intermediate x and s phases were found. X-ray diffraction, metallography and melting points were employed. SEVERAL investigators have described the phases present in the tantalum-rhenium alloy system, but no detailed account of the phase diagram prior to the present investigation appears to be available. Greenfield and Beck' reported the solubility of 48 to 54 at. pct Re in tantalum, a s phase at 41 at. pct Ta, and x phase isomorphous with a Mn from 37 at. pct Ta to less than 25 at. pct. They employed as-arc melted specimens and heat treatments at 1200 °C lasting 72 hr.2 Duwez3 reported the existence of a a phase at the composition Re3Ta2. Niemiec and Trzebiatowski4 observed a lattice parameter a = 9.69A, for the x phase at a composition Ta7Re22, but no s phase. Savitiski and Tylkina5 have shown a hardness maximum at the composition 40 at, pct Ta and a somewhat lower plateau from 35 to 10 at. pct. Knapton6 indicated results similar to those of Greenfield and Beck.' The present investigation describes the phase relationships in the tantalum-rhenium alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURE Commercial 99.7 pct Ta powder from Fansteel Metallurgical Corp. and 99.9 pct Re powder from Chase Brass and Copper Co. were used for alloy preparation. The powders were weighed to desired nominal compositions and then pressed without binder into compacts weighing 5 or 10 g. The compacts were arc-melted six times on alternate sides on a water-cooled copper hearth using a nonconsumable tungsten electrode in an atmosphere of titanium gettered helium, at a pressure of 500 mm Hg. In most cases this procedure yielded alloy buttons of satisfactory homogeneity. A series of alloy specimens were analyzed wet chemically for use as standards for X-ray fluorescence. All specimens were analyzed by fluorescence and the results showed that the compositions differed by less than 3 pct Re from the original as-weighed nominal composition.* On the basis of self-

Jan 1, 1961

Dr. Robert Bell died on June 18, 1917, at Rathwell, Manitoba, in the seventy-seventh year of his age. He was born in Toronto on June 3, 1841, and was a son of the Reverend Andrew Bell of the Free Church of Scotland. He was educated at the Grammar School of the County of Prescott, Ontario, and subsequently at McGill University and the University of Edinburgh. While still a boy of 15 years of age, he joined the Geological Survey of Canada, under Sir William Logan, in the capacity of Junior Assistant, and was rapidly promoted in the service, where lie remained-with but one short interval-for over fifty years, retiring as Chief Geologist and Acting Director in the year 1908. He married Agnes, daughter of the late Alexander Smith, of Westbourne, Glasgow, and Auchentroig, Stirlingshire, and is survived by one son and three daughters. Practically nothing was known of the geology of Canada, and very little with reference to its geography, when Mr. William E. (afterward Sir William) Logan was called upon to undertake the organization of the Geological Survey of Canada, and as its first Director to carry out the mapping of this vast area and the examination of its mineral resources. Dr. Bell's work as a member of Sir William Logan's staff in these early years consisted, therefore, exclusively of geological reconnaisance and geographical exploration. Even in later years, and until his administrative work confined him to his office, Dr. Bell's work remained essentially of this character. The exploratory traverses and track surveys which lie carried out were, chiefly within the area of the great Laurentian protaxis or Canadian Shield, which forms such a striking feature and which has played and will continue to play so important a role in shaping Canadian history and in influencing the character of the Canadian people. Dr. Bell's lines of exploration crossed and re-crossed this area from the Atlantic Coast to the Great Lakes on its western border, and from Lake Huron and Lake Superior on the south to the Arctic Sea, following the water ways of this great land. He also worked along the coast line when acting as geologist and naturalist to the "Neptune" Expedition in 1884, and to the "Alert" Expedition in 1885, both of which carried out explorations in Hudson's Bay and Hudson's Straits; also on the "Diana" Expedition in 1897, when he surveyed the coast of Baffin Land, and was one of the first white men who penetrated to the great 'lakes in the interior of that immense

Jan 11, 1917

By Grover R. Castle

INTRODUCTION Banks are being asked to assume more and more of the project risk in connection with project financings and, as a result, they are seeking to become more sophisticated in the way that they approach these kinds of financings. For example, a large number of banks that are active with the mining companies have established mining groups which typically will include mining engineers, economists, and bankers, in order to specialize their service to the mining industry. These banks have geared up these special service staffs so that they will be better equipped in their lending activities to analyze, measure and evaluate the project risk. The hope is that a team of these specialists will be able to predict the potential success or failure of these new "green fields" mining ventures that the banks are asked to finance. This paper shall focus on this subject and try to determine just how successful these specialists can hope to become as they analyze these various projects that are brought to them for financing. The approach that shall be taken in this paper shall be to examine how successful the mining companies themselves have been in the past with this same problem. These mining companies should be the most sophisticated in their approach to the analysis of the potential for success of a new mine because they have had the most experience in evaluating these projects. After all, who knows more about developing a mine than the companies that have developed similar mines in the past? For the purposes of this paper, the writer has selected a sample of 18 mines that have been developed over the years and measured the actual performance of each of these sample ventures against the original projections. All of these cases have involved the development of large projects where the sponsors or partners in the venture are substantial and sophisticated companies and where the feasibility studies have been prepared by engineering firms that are considered very professional in the industry or alternatively where the feasibility has been done by a comparable in-house staff. The sample cases have been chosen from a period which starts in 1965 and continues through 1981 with the cases distributed over that period as indicated below: [ ] Fourteen of the projects are open pit mines, three are underground mines and one mine starts on the surface and gradually goes underground. Seven of the mines are in the the far east with the remaining three in either South or Central America. The following four specific questions were examined for each project:

Jan 1, 1985

By Werner Ostertag

A series of rare earth cobalt compounds of the composition RCoa (r = Ce, Pr, Nd, Sm, Gd, Tb, Dy, Ho, Ev, Tm, Lu) has been prepared. The compounds crystallize in space gvoup R3m and are isomorphous with PuNi3. Except for CeCo3 and PrCo, the series shows decreasing- values of a. and co. The relalively small parameters of CeCo, and PrCo, are explained by valencies of cerium or praseodymium which exceed the usual rare earth valency of three. The structure of the compounds is discussed as in-fillings of kagome nets in direct and staggered superposition. In the course of a systematic investigation of rare earth cobalt compounds"2 and their magnetic properties,, a series of alloys corresponding to the formula Rco3 has been prepared. The investigation of the Rco3 series was stimulated by our investigation of the yttrium cobalt system2 as well as by reports in the literature: Smith and Hansen4 reported the structure of YcO3 and Van vucht5 that of GdCo3; ceco3,6 Gdco3,7 and DyCo3 7 have been found to be single-phase during phase diagram studies. It was the purpose of this work to report crystallographic data on the entire Rco3 series and to interpret the structure of these compounds on the basis of general principles as discussed by Frank and Kasper.8 At the time this work was terminated, it was learned that a similar investigation has been carried out independently by Bertaut, Lemaire, and schweizer.9 Except for CeCo3 (ao = 4.952, co = 24.73') and NdCo3 (a0 = 5.067, co = 24.76') data of this work are in satisfactory agreement with their investigation. EXPERIMENTAL TECHNIQUES A series of samples having the composition Rc03 was prepared from stoichiometric amounts of the rare

Jan 1, 1968

Annual Meeting,Wallace, Idaho, Nov. 15-16, 1913. The third annual meeting, which was also the eighth consecutive meeting and the second to be held in the Coeur d'Alène district, was held in Wallace, Idaho, Nov. 15-16, 1913, with side trips to Kellogg-Wardner, Larson, and Mullan, where several mills were visited. The meeting was held jointly with the Montana Section, about 50 members and guests being present. Headquarters were in the Samuels Hotel, sessions being held in the public library. The arrangements and program were in the hands of the following local committee: George W. Roddewig, W. Earl Greenough, H. M. Childs. At 2.30 p.m., Nov. 15, the first session was called to order by Prof. F. A. Thomson, member of the Executive Committee, adjournment being taken to the Mine Rescue car, where Mr. Anderson and his assistant entertained the visitors for nearly two hours by demonstrations of mine-rescue and, first-aid practice, after which the party visited the Hercules mill, mention of which was made in the report of last year when the Section visited the plant. There are, however, several important alterations and additions to the flow-sheet to be noted, such as substitution of Chilean and Hardinge mills for the Huntington mills in the regrinding department; rearrangement of the tables and slimers, with a noticeable addition of the later models of the Franz machines, and the installation of the Wyman flotation process, which has been tried out, or is being tested, with more than ordinary success, on the middlings in several of the mills of the district, the Green Hill Cleveland mill being provided with a 100-ton unit, partly described below

Jan 12, 1913

By Ralph Hultgren, Louis A. Carapella

When F. Heuslerl found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.% All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys4 the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intellgently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data. have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. Previous Work In the original work of F. Heuslerl and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for CusMnAl of I = 443 was early measured. Ross and Gray5 found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 hen reinvesti-gated the system, confirmed their results,

Jan 1, 1942

By John Birkinbine

IN the spring of 1878 the Pine Grove Furnace, located in Cumberland County, Pa., was blown in after lying idle for several years. The furnace was constructed in 1770, and for over a century it has been in almost continual operation. The plant consisted in 1877, when the writer was first called there, of a stone stack 32 feet in height, inclosing a shaft and boshes, the latter being 8 feet in diameter. The blast was supplied by two wooden blowing-tubs discharging into a third, having a floating piston sustaining a box weighted to give the desired pressure, the power being furnished by a waterwheel. A small 18-pipe hot-blast stove heated the blast. The furnace was remodelled during the winter of '77-78, and a Weimer blowing-engine with a blowing-tub 5 feet in diameter and 2 feet stroke, and the necessary boilers, were substituted for the wooden tubs and water-wheel. The stack was raised and enlarged, and provided with a bell and hopper having a central drop. Water dam and tymp were added, and general repairs were made. The hot oven, however, was riot increased. The furnace had always been operated with charcoal as fuel, and its reconstruction was made with a view to continue the use of charcoal, but provision was made for ample blowing capacity should other fuels at any time be employed. Although liberal arrangements had been made in cutting wood, the stock of charcoal supplied in 1878 was insufficient for the increased requirements of the remodelled plant, and notwithstanding the purchase of some 80,000 bushels from an adjacent idle furnace, there was riot enough to keep the furnace in constant blast until a new supply could be obtained, particularly as the season was unusually backward. Instead of following the established precedent of many charcoal furnace managers, i. e., blow out every February, it was determined to continue in blast, using coke as fuel. Accordingly, when the charcoal stock was exhausted, on March 22d, 1879, Connellsville coke was substituted, the change of fuel being made at once; that is, the coke charges followed immediately upon the last charcoal charges. After working a few days,-the strike in the Connellsville coke region cut off the supply, and anthracite coal was obtained, a mixture of the two fuels being employed. The strike continuing,

Jan 1, 1880

By Louis A. Carapella, Ralph Hultgren

When F. Heuslerl found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.% All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys4 the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intellgently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data. have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. Previous Work In the original work of F. Heuslerl and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for CusMnAl of I = 443 was early measured. Ross and Gray5 found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 hen reinvesti-gated the system, confirmed their results,

Jan 1, 1942

EVERY forward-looking mining company realizes the need for employing graduate mining engineers so that there will be a supply of qualified men from which to draw for company officers, executives, and mine managers. The mining industry is competing today with numerous other fields of engineering for its supply of technical men, many of which are more attractive than mining because of better pay, living conditions, and well- regulated company training programs. The Ontario Mining Association and the mining companies of Ontario are conducting a postgraduate training plan which if adopted in the United States, might well encourage top quality men to study mining.

Jan 3, 1950

By Gilman C. Ritter

Moisture sampling of uranium ore should coincide as nearly as possible with weighing of the lot represented by the sample. This requires care by the sampler since the sample must usually be taken as a grab from each truckload as dumped. Correct proportions of coarse and fine material are necessary. A sample of at least 10 lb should be collected, placed in an air tight container, and promptly taken to the moisture determination room. Further, the sample should be dried for a minimum of 24 hr or until there is no further apparent loss of weight at a temperature no greater than 110°C.

Jan 10, 1958

Percussion drilling with tungsten carbide insert button bits ranks among the most significant advances in both underground and surface drilling in medium and hard rock formations. Getting top performance and life from these upfront components is not particularly difficult if one pays attention to the basics in operation and maintenance. For some reason, a few of the essential operating and maintenance steps for getting the most from these tools seem to have gotten turned around; instead of operating at the near optimum levels, some miners, in following myths or misunderstandings about them, are shortchanging their optimal utilization. Let's examine the two most harmful ones.

Jan 8, 1978

By K. Koneko, T. Nokoyama, S. Shibato

SEYBOLT et al.' have detected various silica films formed on a 3 pct Si-Fe alloy after heating at low oxygen potentials with the electron diffraction method, and they have made some observations on the H,0/H2 ratios required to form them. The purpose of this note is to describe the structure of the oxide film formed on either mechanically or electrolytically polished surfaces of a 3 pct Si-Fe alloy containing small amounts of manganese after heating at low oxygen potential. The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron, 76 pct ferrosilicon, and 76 pct ferromanganese, vacuum-in-

Jan 1, 1969

By Michael R. Lewis, Dennis P. Moore

Untensioned, fully grouted, steel bars (dowels) up to 30 m long and 45 mm in diameter were used to reinforce rock slopes several hundred metres high, excavated for a hydroelectric project near Revelstoke, British Columbia. These dowels were successfully used to prevent surface rock from loosening, to prevent sliding on interconnected discontinuities and to prevent sliding of relatively intact rock on a thin shear zone. Because the interaction between rock slopes and dowels is not well understood, critical slopes were extensively monitored. Based on the experience from Revelstoke and elsewhere, it appears to be worthwhile, in most circumstances, to reconsider the need for tensioning rock anchors.

Jan 1, 1982

By O. B. Hofstrand

Solid bodies mill float in a liquid by reason of lower specific gravity, or of peculiar form, or of repellent action towards the liquid which prevents them from overcoming the resistance of its surface-tension. To the last of these causes the flotation of ores is to be ascribed. Nearly all ores and gangues are specifically heavier than water, yet they do not behave alike in this respect, and they may be divided into two classes, those of floatable and non-floatable minerals respectively. Upon a close examination of these two groups of minerals we find that those particles that will float on the surface of

Jan 1, 1913

THE Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division The following were the Howe lectures and lecturers for the years indicated 1924 What is Steel? By Albert Sauveur 1925 Austenite and Austenitic Steels By John A Mathews 1926 Twenty-five Years of Metallography By William Campbell

Jan 1, 1952

By R. A. Blake

Measurements of the quantity of xanthate abstracted from mineral surfaces and put into solution by an increase in the hydroxyl ion concentration were made. A residual xanthate concentration of 59.6 ppm was found in one case at a pH of 11.8. The abstracted xanthate is capable of acting as a collector on fresh mineral surfaces under proper conditions. It was learned that as the hydroxyl ion increased and the xanthate abstracted, the coarse particles lose their floatability first. A volume weight relationship based on percentage coverage was established and seems to offer a reasonable explanation of the cause of observed results.

Jan 1, 1973