Search Documents

By AIME AIME

A PAPER recently presented before the Anthracite Section of the A. I. M. E. by S. J. Phil- lips, Mine Inspector, Fifth Anthracite District, Department of Mines of Pennsylvania, covering the water hazards in the anthracite coal mines of the Lackawanna River Valley, was especially timely because the conditions there are duplicated to a large extent in the Wyoming Valley, which is traversed by the Susquehanna River with its many large tributary streams. Also, in the southern anthracite field, where there are a number of large creeks, similar pumping problems and mine water hazards will in time be presented if mining is continued to its conclusion.

Jan 1, 1936

By W. A. Backofen, B. B. Hundy

THE pole figure interpretation in a recent paper' on the torsion texture of copper was questioned in discussion,2 nd a simpler alternative interpretation was proposed. In the hope of reaching a positive decision in favor of one or the other, further studies were undertaken with 70-30 brass and Armco iron. This additional work has not answered all the questions about torsion textures, but the new pole figures do offer support for the original interpretation and show that the texture is more complicated than the alternative suggests. From the previous paper,' the appropriate method of describing the texture in a twisted bar is known to be a pole figure plotted on a plane tangent to the surface of the bar. The axes of the pole figure are chosen to coincide with directions in the tangent plane which are parallel and at right angles to the bar axis (the longitudinal direction, L.D., and the transverse direction, T.D.), for these directions define symmetry axes of the texture. Therefore any ideal orientation that might be selected to represent the texture gives the crystallographic plane parallel to the tangent plane and the crystallographic direction parallel to the axis of the torsion specimen. A unique texture was assumed in the original interpretation, and the four ideal orientations, (112) [111], (111) [112], (110) [001], and (112) [131], were used in its description. Of the four orientations, the first three provide possible slip directions along the direction labeled T.D. in the pole figure, which is one of maximum shear stress in a specimen being twisted. The alternative, however, simply considered the texture to be made up of two components, one a [Ill] alignment along the specimen axis with a random orientation about the axis as in the wire texture, and the other a superimposed orientation (110) [0011. Experimental evidence for this simpler interpretation was derived from two observations: 1—twisting did not alter the orientation of a single-crystal torsion specimen of a brass in which an octahedral plane was perpendicular (and a [Ill] direction parallel) to the axis, and 2—deformation bands with approximately the (110) [001] orientation were seen to develop in the crystal during the test. The new pole figures were obtained with a brass and an iron torsion specimen of 3/4 and 1 in. gage length diameter, respectively. After annealing, polishing, and twisting, seven rods, about 0.030 in. in diameter and with different orientations, were prepared from material near the surface of each specimen; these were required for the method of constructing pole figures by using a Geiger counter as developed by Norton.5 Since the shear strain gradient in plastic torsion is linear, it was readily computed that the material supplying the brass rods had been subjected to a shear strain of about 3.2, and that supplying the iron rods had received a shear strain of about 2. All details concerning specimen design, testing procedure, rod preparation, and use of the Norton technique can be found in ref. 1. Only this procedure was followed in working out the (111) and (100) pole figures for brass, Figs. 1 and 2. However, X-ray photograms were also involved in the construction of the (110) pole figure for Armco iron, Fig. 3. The photograms were made according to the conventional transmission diffraction technique using a small sheet taken parallel to the specimen surface and etched to a thickness of about 0.0025 in. They were especially important in locating the boundaries

Jan 1, 1954

By W. L. Honnold

AS BOTH South Africa and diamond mining are unfamiliar subjects it seems best that on such an occasion as this I should endeavor to reflect the atmosphere of the place and to picture the mines from an industrial rather than from a technical standpoint and, because of long absence, my remarks must necessarily be sketchy and in some particulars not up to date. The preferable route to South Africa is via England, direct steamers from America being inferior as to service and effecting no saving of time. The newer boats are of about 20,000 tons capacity and very comfortable. Seventeen days are required for the voyage and only one stop is made-that at the island of Madiera, three days out. Between Southampton, the port of departure, and Madiera the weather may be warm or cold and the

Jan 1, 1925

By Leon Borgman, Michael P. Lipkewich

Orebodies at or near the surface are generally amenable to open pit mining. The development of a mining program involves designing an ultimate pit and a production schedule. This pit maximizes total profit while the production schedule maximize6 the present value of the property. Optimum pit limits can be approximated by two-and three-dimensional numerical techniques. These techniques presuppose that the mineralized area has been sufficiently sampled to allow a reasonably accurate prediction of grade at any spatial location.

Jan 1, 1969

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water -by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other, adsorbent earths.

Jan 1, 1929

By CHARLERS R. FETTEE

A slight decrease in drilling activity occurred in the oil fields of western Pennsylvania during 1945 and a considerable decrease in the shallow-gas territory (Upper Devonian or higher). The number of deep tests (Middle Devonian or deeper) completed was two less than in 1944 and these did not open any new reserves of natural gas. Thus far, no commercial oil has been encountered in sands below the Upper Devonian in Pennsylvania. Oil production declined 8 per cent.

Jan 1, 1946

By HENRY COLEMAN

WE as employees of these related companies, I am sure, are proud to be affiliated with them, and have great faith in the sagacity and fore- sightedness of our employers. Most of us here have been called into important positions in these organizations, and it should be our most earnest endeavor to sense and carry them out as if they were our very own. We have been asked to supervise and carry on a work over which our employers cannot personally watch. It has been well said that the most efficient organization is that which requires the least attention from its head. Because of the very nature and condition of our work, which separates us by many miles from our employers and makes it impossible for us to receive attention and instructions from the heads of our departments, save for occasional visits and correspondence, we are given a great opportunity to prove that we can be efficient workers without too much attention from the heads of our departments. There are few employees who cannot do their duty when it is laid before them in specific terms, and when their employers are always there to see that their plans are carried out. But the employee who is really giving efficient service sees his duty himself and willingly does it. '

Jan 1, 1931

H. H. Stoek, Scranton, Pa. (communication to the Secretary): Mr. Rothwell's condemnation of my paper on the International Correspondence Schools as not giving an impartial view of the whole field of such enterprises, because it was confined to the description of a single one, might be legitimate if I had undertaken or professed to do anything else than that which I was requested by the Secretary of the Institute to do—namely, to give an account of this particular institution. This is a sufficient answer to all his direct or implied criticisms upon my omission to mention either persons or organizations outside of the special limits set for me. Recognizing fully that personalities have no place whatever in the Transactions, I regret the necessity of making the following statement in answer to Mr. Rothwell's charge that I omitted to give due credit to Mr. Ewald, a former principal of the International Correspondence Schools. The Colliery Engineer School of Mines was started in 1891, and its first student was enrolled October 16, 1891. During the fall of the same year the mine-mechanical course was laid out along the same general line that had already been followed in the mining course. This mine-mechanical course was the foundation from which sprung the later developments of the several mechanical courses. The latest circulars of information of the International Correspondence Schools give the following as their distinctive features: (1) courses of instruction for particular occupations,

Jan 1, 1900

By C. Q. Payne

(New York Meeting, February, 1912.) THE art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates back to the year 1806, when they were employed in Cornwall, their principal development has taken place during the last 30 years. To Stephen R. Krom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contribution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the movable roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springs, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to exercise new functions. In developing crushing-machinery for his Portland cement works, Mr. Edison constructed ? giant " rolls, having a diameter of 6 ft. and a length of. face of 7 ft.

Jun 1, 1912

By C. K. Leith

THE resolution presented at the Annual Meeting of the A.I.M.E., calling on Congress to provide now for postwar accumulation of mineral stock piles under Government control, expresses, I think, the nearly unanimous view of the mining industry. As a result of the trying experiences of the first World War, Mr. Baruch, in his report of Dec. 24, 1919, to the President, urged that steps be taken at once to ensure adequate supplies of raw materials for future emergency. In the twenty years that followed, the same program was vigorously urged on Congress by many individuals and agencies, public and private, including the Secretaries of War and Navy, many members of Congress, the Bureau of Mines, the Planning Committee for Mineral Policy appointed by President Roosevelt, the A.I.M.E., the Mining and Metallurgical Society, and others.

Jan 1, 1943

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800' and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,',' in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

By Linn Bradley

Introduction MARKED differences of opinion have been expressed by engineers interested in cleaning iron blast-furnace gases for use in hot-blast stoves and under boilers, in reference to the advantages of a hot-dry method over a cold-wet method. One point at issue involves the sensible heat energy in the moisture contained in the gas. Some advocates of the cold-wet methods claim that the condensation and resultant removal of the greater portion of this contained moisture by wet scrubbing, spraying or similar methods, results in a saving of some of this sensible heat energy, by reason of the fact that water vapor has a high capacity for sensible heat energy and may carry from the exit of a hot-blast stove, for example, more heat units than are sacrificed or lost when the gas is cleaned by this cold-wet method. Other advantages claimed for the latter method are: That gas burns more readily when it is free from moisture in any form; that because gas is made denser by cooling and removing the moisture it has a higher calorific value than hot gas carrying moisture; and that higher flame temperatures are obtained when the gas is cleaned by the cold-wet method. A search through the available literature fails to disclose any extensive calculations or records of conditions obtained in practice, bearing upon these phases of gas cleaning. This paper deals with these problems from the standpoint of the economy of using a gas of higher flame temperatures, of improved stove design, and of economy in the gas-cleaning department. Calculations have been made which show that by cleaning the gases by a cold-wet method the sensible heat energy of the blast-furnace gases is greatly reduced; and, in general, this loss of heat energy is far greater than that lost from the stoves or boilers due to the sensible heat capacity of the water vapor if carried away by the exit gases. By making use of the

Jan 2, 1917

By AIME

Compiled by Mary Ann Gross, Department of Energy. Bruceton. PA. Supplemental data from Coal Age indicated by (*). Reprinted by permission from CoalAge magazine.

Jan 1, 1981

By J. W. Cunningham, M. J. Stultzman

THE demand for improved materials for high-temperature service has increased during the last few years. Iron,- nickel,- and cobalt-base alloys have been investigated extensively and many alloys with outs'tanding high-temperature strength have been developed. Considerable research has been directed toward improved methods of processing these alloys. The vacuum furnace as a tool for the purification and improved control of high-temperature alloys has been studied extensively and production units are in operation. The research covered by this paper studied the effects of casting in air, vacuum, or argon upon the elevated-temperature properties of two nickel- and two cobalt-base alloys. The alloys investigated were Stellite 31, He 1049, Udimet 500, and Guy Alloy. MELTING AND CASTING PROCEDURES Two heats of each of the four alloys under investigation were melted and investment cast under the following conditions: 1) Stellite 31 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 2) He 1049 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 3) Udimet 500 was melted and investment cast in vacuum with and without additions of zirconium and boron. 4) Guy Alloy was melted and investment cast in vacuum and in argon. The heats were all melted in induction furnaces equipped with preformed magnesia crucibles of 50-lb capacity. The air-melting furnace was powered by a spark-gap converter of 40 kw capacity. The vacuum-melting furnace was powered by a motor-generator set of 100 kw capacity. The argon heat of Guy alloy was melted in the vacuum melting furnace under an argon atmosphere. Virgin materials were used for preparing all heats except the air heats of Stellite 31 and He 1049. The charge for the air heat of Stellite 31 was a commercial blend of shot. The charge for the air heat of He 1049 was Stellite 6 shot plus those virgin materials necessary to give the desired composition. All of the materials used were of the same grade used com-

Jan 1, 1960

By Paul Billingsley

THE term Boulder batholith was first applied in 1897 by W. H. Weed'2 to the extensive mass of granite in western Montana within whose borders occur the ore, deposits of Butte. In a general, way this was known to extend from Helena on the north to the Highland Mountains near Butte on the south, and to be relatively narrow in its east-west diameter. Its intrusive relations to the surrounding sedimentary , rocks, and its probable Tertiary age, were described by Weed, but in many ways his statements, based upon incomplete data, have required revision. Most notable of the errors of this description of the batholith were the failure,3 since corrected, to recognize the intrusive contact of the granite with the capping of andesite, and the complete absence of any reference to the many extensions of the granite beyond the somewhat narrow limits of its largest exposure.

Jan 1, 1915

By L. C. Morganroth

Magnesites are of two general classes - massive and crystalline.

Jan 1, 1915

By AIME AIME

THOUGH the dust-control systems in the crushing plants and other buildings at Morenci do not differ materially from similar installations in other large copper reduction works, it is probable that in few other plants has as much attention been paid to the dust problem. Possibly the most striking feature of the Morenci installation is the manner in which the necessary equipment has been built into the various structures, and the absence of unsightly pipes, ducts, and fan houses. That this result has been attained is due, in no small part, to the basic conception that the control of the dust in a milling plant should be an essential part of the process itself and not something to be tacked on later after the plant is in operation. The control systems were designed and developed along with the general plant construction program and when the first car of ore was dumped into the crusher the dust-control equipment was ready.

Jan 1, 1942

By A. L. Holley

THIS process is performed in the Pernot puddling furnace; it removes from 75 to 80 per cent. of the phosphorus, most of the sulphur, and practically all the silicon, from crude iron, in from five to eight minutes. It has been in regular use since March, 1877, and has prod uced over seventeen thousand tons of washed metal for the open-hearth furnace. During two years, nearly all, and lately, all the open-hearth steel produced in these works has been made from about 5 tons of washed pig and 2 tons of scrap per open-hearth furnace heat. There are 12 open-hearth furnaces, of which 4 to 9 are running, according to the state of orders. A large amount of highly phosphoric iron from France and Belgium has been also washed and then puddled for parties who have taken, or are expected to take, licenses. The washing of pig for puddling, however, is not a practice at Krupp's works, because pure pigs are nearly as cheap as impure ones. The author and his assistant, Mr. Laureau, spent, during the last month, three days at Krupp's works, examining this process. They copied out of the office books characteristic analyses and physical tests, some of which are given herewith. They also brought hone many samples of pig, cleaned metal, puddle bar, and steel, which they saw treated. Analyses of some of these samples appear in Table IV. As there are no blast furnaces at Essen, the iron is melted in two Bessemer cupolas with fore-hearths; they melt 12g pounds of iron with 1 pound of coke. The metal is run by a spout from the fore-hearth into an opening at the side of the main door of the washing-furnace. The Washing furnace.-This is a regenerative gas furnace. It has a Pernot revolving-hearth of 12 feet external diameter and 3 feet depth. (See Plate.) The four regenerator chambers have 780 cubic feet capacity, which is about the same as the average regenerator capacity of open-hearth steel furnaces of equal tonnage. The lining is 13 inches thick on the sides and 9 inches on the bottom, thus giving a hearth 9 feet 10 inches by 2 feet 3 inches deep. The lining is composed of lumps of highly refractory ores

Jan 1, 1880

By A. L. Holley

This process is performed in the Pernot puddling furnace; it removes from 75 to 80 pel. cent. of the phosphorus, most of the sulphur, and practically all the silicon, from crude iron, in from five to eight minutes. It has been in regular use since March, 1877, and has produced over seventeen thousand tons of mashed metal for the openhearth furnace. During two years, nearly all, and lately, all the open-hearth steel produced in these works has been made from about 5 tons of washed pig and 2 tons of scrap per open-hearth furnace heat. There arc 12 open-hearth furnaces, of which 4 to 9 are running, according to the state of orders. A large amount of highly phosphoric iron from France and Belgium has been also washed and then puddled for parties who have taken, or are expected to take, licenses. The mashing of pig for puddling, however, is not a practice at Krupp's works, because pore pigs are nearly as cheap as impure ones. The author and his assistant, Mr. Laureau, spent, during the last month, three days at Krupp's works, examining this process. They copied out of the office books characteristic analyses and physical tests, some of which are given berewith. They also brought home many samples of pig, cleaned metal, puddle bar, and steel, which they saw treated. Analyses of some of these samples appear in Table IV. As there are no blast furnaces at Essen, the iron is melted in two Bessemer cupolas with fore-hearths; they melt 124 pounds of iron with 1 pound of coke. The metal is run by a spout from the forehearth into an opening at the side of the main door of the washingfurnace. The The washing-furnace.—This is a regenerative gas furnace. It has a Pernot revolving-hearth of 12 feet external diameter and 3 feet depth. (See Plate.) The four regenerator chambers hare 780 cubic feet capacity, which is about the same as the average regenerator capacity of open-hearth steel furnaces of equal tonnage. The lining is 13 inches thick on the sides and 9 inches on the bottom, thus giving a hearth 9 feet 10 inches by 2 feet 3 inches deep. The lining is composed of lumps of highly refractory ores

Jan 1, 1880