Search Documents

By Harrison, Henry Fay

The study of an entirely new series of alloys may be undertaken from a desire to obtain knowledge applicable to the perfection of industrial alloys, or merely to test certain theoretical considerations. In the case of antimony-tellurium alloys, the theoretical side only is at present important; but it is hoped that the results of this investigation may have some industrial value, at least indirectly, by furnishing one more example for comparison when studying commercial alloys. The statement is found in various places that antimony is isomorphous with arsenic, bismuth and tellurium; but very little experimental evidence has been offered in support of this assumption. All four metals crystallize in rhombohedra, and the ratio of the axes a: c is approximately the same—which seems to indicate, but does not prove, their isomorphism. The close association of these metals in minerals also seems to indicate that they are isomorphous. There are, however, certain differences in their properties which render this coriclusion somewhat doubtful, and it is therefore desirable that inde-

Jan 1, 1902

By J. Chipman, N. J. Grant, J. C. Fulton

This paper contains data on the distribution of silicon between liquid iron-silicon-carbon alloys saturated with respect to graphite and CaO-SiO2-Al2O3 slags under 1 atm of CO at 1600°C. The ranges of slag compositions studied were extended from the dicalcium silicate saturated liquidus composition up to silica concentrations at which Sic appeared as a stable phase. IN blast furnace operation it is not to be expected that slag and metal reach equilibrium with one another. Nevertheless, the silicon content of the metal varies with slag composition and with temperature in a manner which would be predicted from equilibrium considerations. Similarly, the distribution of sulphur between slag and metal does not attain an equilibrium state, yet the influence of slag composition is strongly analogous to its effect on the distribution equilibrium. The desulphurizing power of metallurgical slags has been shown to be highly dependent upon the FeO content of the slag. Moreover, the rate of removal of sulphur from slags is influenced by the oxygen potential of the slag-metal system. Thus it was shown by Grant, Kalling, and Chipman1 that the presence of MnO in slags which are low in FeO causes a marked slowing down of the transfer of sulphur from metal to slag. This led to the hypothesis that the slow removal of sulphur by blast furnace slags of more acid composition might be due in part to the effect of SiO2 on the oxygen potential of the system. This was verified in the work of Grant, Troili, and Chipman,' who found that the desulphurizing power of the more acid blast furnace slags could be markedly improved by an increase in the silicon content of the underlying metal. Their explanation of this improvement was that the higher silicon content of the metal decreased the rate of transfer of more silicon and, along with it, of oxygen from the slag to the metal. The slowness of the transfer of sulphur from metal to slag was the result of the slow reduction of SiO2 from slag to metal. Attempts to study the rate of sulphur removal had in the past resulted in very slow rates corresponding to the rates of silica reduction. It has become evident on the basis of these studies that further experimental studies on the rate of removal of sulphur must take these factors into consideration if there is to be a clear understanding of the rate of sulphur transfer under conditions simulating those existing in the blast furnace. It will be necessary, at least in a part of such study, to employ combinations of slag and metal in which the disturbing effect of silica reduction has been eliminated; in other words, to employ slag-metal combinations which are already in equilibrium with respect to the transfer of silicon. In preparation for such studies of desulphuriza-tion, a preliminary program of research on the distribution of silicon between slag and metal has been undertaken. This will ultimately include a comprehensive survey of the effects of temperature and slag composition on the equilibrium distribution of silicon between slag and metal. The present paper is a report on experimental methods employed and on

Jan 1, 1954

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with law ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the site range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for various reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas-containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully

Jan 1, 1953

By L. F. Wright

Operations of these two mining companies have some superficial similarities-geographical location, production rates, comparatively large ore reserves; but any critical comparison of mining and milling procedures or of economics must take into account the striking differences in geological environment and mineralogy of the respective ore deposits. The properties are only about 20 miles apart on an upland surface of moderate relief (part of the Interior Plateau of central B. C.) which occupies an area east of Thompson River between the towns of Ashcroft and Merritt. Being in the "dry belt" of British Columbia, water conservation is necessary at both operations.

Jan 12, 1963

Copper ores from small mines in the area south of Tucson, where the Twin Buttes mine is located, were first operated in the 1880's. Today this area is one of the great copper mining centers of the world. In 1963, Anaconda Company acquired the property from Banner Mining Company and in recent years joined with AMAX in a 50/50 partnership to work the Twin Buttes property. From the beginning, Anaconda had relied on conveyors to remove overburden, oxide material for eventual leaching, and ore from the open pit. In the large st preproduction stripping program in mining history, Anaconda in a four-year period (1965 to 1969) removed 266 million tons of overburden of an average depth of 500 ft (152 m) lying over the ore body. The alluvium overburden was stripped by scrapers carrying 70 to 80 tons and push-loaded by two D9 tractors operating in tandem. The scrapers delivered their loads to bins which fed a 60 in. (1.52 m) conveyor having a capacity of 8500 tph. The 25% slope belt conveyor, which was 2100 ft (640 m) long, transported the material to the brow of the pit, where it was transferred to an 8300 ft (2530 m) surface belt to a 1000 ton loadout bin. At this point, the overburden was trucked to the sites of the tailings ponds, where it was used for dam construction. During 1976, the one billionth ton of overburden was removed from the Twin Buttes mine. The Twin Buttes quartz monzonite porphyry contains only scattered mineralization of which chalcopyrite is the most abundant mineral, associated with chalcocite, covellite, minor bornite, and several oxide minerals. Oxidation has progressed to variable depths of up to several hundred feet below the base of the alluvium. Because of the depth of the sulfide and oxide ores and hard rock waste, two in-pit crushers and conveyor systems were also installed for their transport out of the pit; and in 1976 a third crusher and conveyor system was installed lower in the pit for waste rock only. The two initial crushing and conveying systems were designed to handle any of three functions: crushing waste to be disposed of by a rail-mounted stacker -conveyor, crushing oxide ore for conveyor and then truck transport to stockpiles for future leaching, and primary crushing of sulfide ore for conveyor transport to the two 30 in. by 70 in. (0.76 by 1.78 m) secondary crushers and the two 7 ft (2. 13 m) standards and four 7 ft shortheads in the third and fourth stage crushing plant. A third standard crusher has been in- stalled recently. Mining is done by 15 yd (11.5 cum) shovels which load 100- and 150-ton

Jan 1, 1978

By T. S. Lundy, F. R. Winslow

DIFFUSION coefficients of Hf181 in the high-tem-perature bcc phase of reactor-grade hafnium were determined at temperatures of 1795° to 1995°C by standard lathe-sectioning techniques. The temperature dependence of the data may be described by an Arrhenius-type expression for this limited temperature interval. However, hafnium is classed with the "anomalous" bcc metals zirconium, titanium, and y uranium by the low values of Do and Q observed in this study. The hafnium metal was received as 1/2-in.-diameter crystal bar. Analyses by the Analytical Chemistry Division of Oak Ridge National Laboratory showed the major impurity to be zirconium— about 2.1 pct. The total interstitial content was about 225 ppm with 190 ppm of this oxygen. The Hf"' was supplied as HfC12 in HC1 solution by the Isotopes Division of Oak Ridge National Laboratory. The hafnium bar was cut into disk-shaped specimens 3/8 in. long. One of the flat faces of each specimen was metallographically treated and then the isotope was deposited by vacuum evaporation from a tungsten filament. A 3 by 3 in. NaI (Tl) crystal with a single-channel analyzer was used for counting y rays with energies of 0.3 to 0.7 Mev. The as-deposited layers of isotope had counting rates of about 200 counts per sec. Specimens were annealed in argon in a tantalum resistance furnace. Temperatures were measured with a microoptical pyrometer calibrated for the particular furnace sighting conditions. All sectioning was done by standard lathe techniques. Section weights were determined on a semimicrobalance. A density of 12.5 g per cu cm was used in determinations of section thicknesses. Activities associated with the various sections were measured and the penetration data were treated using the computer code by winslow.' In all cases, except for specimens annealed at temperatures below 1795°C, normal Gaussian penetration behavior resulted. At lower temperatures, plots of In A(x) vs x2 were nonlinear [~(x) = relative activity at a distance x from the

Jan 1, 1965

By T. J. Woodside

Prior to 1927 the lead blast furnace charge at El Paso consisted principally of direct-smelting carbonate ores, very low in zinc, and the resulting slag seldom carried more than 4.0 pct. With the exhaustion of the mines in Northern Mexico which supplied these ores, they were supplanted with a much smaller tonnage of sulphide concentrates containing appreciable amounts of zinc, and the zinc content of the slag rose to 10.0 pct. The Anaconda Company's slag fuming plant at East Helena, Montana, had then been in successful operation for several years, and it was immediately recognized that, while at that time the production of high zinc slag was small, if the grade held, a plant for the recovery of zinc from the accumulated slag might some day be practical. The grade not only held but became increasingly higher so that by 1946 suffcient slag had been accumulated to warrant the construction of a fuming plant regardless of future slag production from the blast furnaces, and with the removal of Government restrictions on construction at the end of the war the project was undertaken. The general design of the plant follows that at Bunker Hill, with waste heat boiler, unit coal pulverizers and even more extensive instrumentation and automatic control. The area around the lead blast furnaces is rather congested, being cut off from the nearest feasible site for the fuming plant by the copper plant, so that the most practical route for hot slag transfer is through the converter aisle. For this reason and also to make use of the existing converter cranes to serve the fuming furnace, an unused reverberatory at the north end of the converter building was dismantled and the fuming furnace and boiler located in its place. A flue at right angles to the furnace and boiler runs northward to the U-tube coolers and baghouse (Fig 1). From the bag-house a steel flue runs eastward to an existing and long unused 300 ft con- Crete stack. The coal handling system and de-leading plant lie north of the furnace and east of the cooling tubes and baghouse. The furnace is conventional, 8 X 21 X 33 ft high inside and completely water jacketed (Fig 2). There are 21

Jan 1, 1950

By D. W. Loucks

There is plenty of evidence to indicate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money: to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before, automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system.

Jan 1, 1949

By L. C. WYMAN

THIS paper discusses what mining reports should contain when presented to the California State Corporation Department, to accompany applications for the sale of stock to the general public, but the principles involved apply to mine financing everywhere. Such reports should 'be as clear and concise as possible, endeavoring to tell the truth in as few words as necessary. Should the engineer be aware that his report is to be used in connection with the sale of stock to the general public, he should consider the public as his client as well as the person who actually employs him. It is always required that the engineer be favorably known and of recognized standing. The following points should be given careful attention : 1. A legal description and location of the property. 2. Transportation conditions, and how they may be expected to affect the operating costs. 3. A brief history of the property, its production record as to tonnage, grade, and character of the ore should be given. Should the property have suspended operations for any reason, this should be given. Any details of former operating costs should be given, especially as to how any improvement could be made, due to better methods which might be employed.' 4. The main geological features and whether they are such as to lead the engineer to believe that the mine may possibly 'be exhausted or the ore of such grade as to be no longer profitable. If he considers them favorable, he should give his reasons for the belief that further development work may produce profitable results. A map showing these features should be submitted, and it is not necessary that such map be highly colored or contain any more than the essential matters. 5. Other mines in the district, or those with similar

Jan 1, 1929

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the. class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. Senior Members: The Directors may, at the special request of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, transfer such Member or Associate to the class of Senior Member; and in special cases may waive either the requirement as to age or as to the number of years for which dues have been paid. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified -through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. .SEC. 8. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life memberships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Affiliate: Upon appropriate action by the Board of Directors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1940

By T. W. Martin, T. J. Crocker, J. M. Goris

The current technology of large rock conveyors is reviewed. Based on this investigation two large rock conveyor concepts have been developed and a test facility investigation designed and fabricated. The USBM will test these concepts along with loading and transfer points for handling mine run rock material up to 1.5 m (4.9 ft) in size. An evaluation of open pit mining systems using large rock conveyors documents substantial cost savings when compared to truck haulage.

Jan 1, 1983

By David R. Maneval, Jack M. Campbell

The regulatory process by which governmental authorities acknowledge and, in turn, permit the location, construction, and operation of large scale energy-related facilities has become extremely detailed in recent years. One example of the detail that is entailed in the regulatory process is the number of permits that must be acquired by operators prior to the construction and operation of energy-related facilities. It has been estimated, for example, that 75 permits are required prior to the opening of a new coal mine in Pennsylvania while 50 are required in Kentucky. From the perspective of facility owners and operators the regulatory process often appears overly complex and may be perceived as a constraint to the corporate decision making process. From the perspective of those responsible for administering regulations, the process is perceived as a means by which public desires-pursuant to social objectives such as environmental protection and occupational safety-can be achieved. As a result of conflicting organizational interests, the clash between energy facility owners and operators and their regulators appears to be inevitable. Furthermore, the resolution of this conflict lies in the trade-off between objectives and the costs of regulation. The balance of objectives and costs is a subject of the political process and not a topic of consideration in this paper. This paper is concerned with the actual administration of regulations, that is, the implementation of that which arises from the interplay of organizational interests. The paper assumes that environmental control laws will not likely be repealed, that regulations to implement the intent of these laws are here to stay and thus the paper seeks to assess how regulations are administered at various levels of government pursuant to objectives. The paper hypothesizes that the administration of objectives (or policy) has an impact on decision making which affects energy facility decision making. While recognizing the fact that regulatory policy cannot be totally divorced from administration, this paper proceeds under the assumption that elements of the regulatory process may be examined individually. The subject of this study is limited to the interplay between regulatory agencies and their clientele.

Jan 1, 1979

By Morris M. Fine, Norwood B. Melcher

As a raw material, prereduced pellets can be considered symptomatic of the quiet revolution taking place in the quality and grade of blast furnace burdens for the past decade. In 1954, the average analysis of ores from U.S. ranges in the Great Lakes area was 50.86% Fe (natural), 10.22% SiO2, and 10.90% moisture; ten years later, the average was 56.67% Fe (natural), 8.13% SiO2, and 6.17% moisture. The advance in Canada was even more pronounced in a lesser number of years. In 1957 the average product of Canadian ore-producing areas was 51.62% Fe (natural), 8.59% Si02, and 8.02% moisture; in 1964, the average grade was 59.59% Fe (natural), 6.27% SiO2, and 3.94% moisture.2 These dramatic data are testimony to the giant strides made in iron ore improvement, and the next logical step is prereduction. Prereduction can well be considered as a beneficiation step in which oxygen is the gangue. Since the ultimate objective of milling and smelting is iron metal, non-metallic constitutents in general, whether oxygen or silica, are contaminants. The past and continuing attack aimed at lowering the silica content of concentrates is succeeding. One need only thumb through the Grade Name listings of the American Iron Ore AssociationVo note that virtually all commercial pellets contain less than 8% silica, many are lower than 6%, and a few below 45%. With natural technical evolution, it is expected "many" rather than "few" will ultimately be in the last category and further mechanical concentration will have reached the point of diminishing returns. At this level, oxygen would constitute the only major diluent worthy of attack.

Jan 7, 1966

By Byron E. Eldred

(Pittsburg Meeting. March, 1010.) GENERALLY speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This. narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. Yet these other arts show quite plainly that a thermal-value basis alone is Dot sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a careful study of the application of the heating-agent in the form of the long flame, and in the production of the heat in contact with, or in direct proximity to, the object to be heated. Of necessity, in boiler-practice, combustion cannot be maintained in actual contact with, or in close proximity to, the object to be heated. Speaking in a general way, heat is imparted from burning bodies to things to be heated in two ways : directly, by radiation, and indirectly, by transfer of the sensible heat of hot gases by convection or contact; by conduction from the hot uses. Both ways are utilized in boiler-practice-directly, by

Jun 1, 1910

By Sir Albert E. Kitson

The manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In certain respects they have a strong resemblance to those of India and Brazil, as contrasted with those of Tertiary age in Georgia, but in this paper no careful comparison with them can be made. Viewed from the present condition of the manganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments. Youngest are the products of decay and degradation with the concentration of manganese oxide in the rocks of both groups. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate degree of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows, largely of basic types. This has been named the Birrim System. Its age is unknown, for no definite fossils have been discovered in it. Since these non-fossiliferous strata at many plaees are of a character which in many parts of the world are suitable for the preservation of fossils, and which contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim System have normally a northeast-southwest strike, and are folded, but not to any very great degree except in certain belts. From the Eastern Province of the Gold Coast they may be traversed diagonally across their strike for upwards of 600 miles, to the extreme northwestern corner of the Northern Territories. Thence they probably extend much farther into French territory.

Jan 1, 1927

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, 'pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.' However, the components which are strongest in the recrystallization texture are in this range.'________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,' 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.'~-'~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.' In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2'13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,'~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.' state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967

By Robert Glass Cleland

Anson G. Phelps 1834-1853 Anson G. Phelps, Jr. 1839-1858 Charles C. Dodge 1864-1878 Daniel James 1834-1878 [ ]

Jan 1, 1952

By L. R. Velho, N. A. D. Parlee, J. Gani

THE unsteady-state type of gas-liquid metal diffusion cell1 has found considerable application.2"4 Cells of this general design can function as steady-state cells if allowed to operate long enough to reach steady state. This report tells of some success in the adaption of this type of cell for steady-state work, using the 0-Ag system in which the mass transfer of the gas "species" is basically controlled by diffusion in the liquid. The gas, e.g-., O2, is maintained in the cell tube'-3 at 1 atm pressure, Fig. 1, by buret and sensitive oil manometer. The gas, after diffusing through the stagnant metal, escapes at the annular metal surface around the tube at a lower constant partial pressure, in this case that of O2 in slowly flowing air, 1 atm.

Jan 1, 1970