Search Documents

By J. George Gregr

INTRODUCTION This part contains field case studies of typical mishaps, accidents, equipment damage or post installation failures resulting from mistakes in design, manufacturing and construction, as well as improper storage, handling and installation procedures of the equipment covered in Part 1. GENERAL Certain mistakes are repeated and common rules violated on almost all industrial equipment installations, with the inevitable consequences of additional cost, construction delays and aggravation of all parties involved. The most common failures are in the following areas: Cleanliness of all components during installation and later in operation. Adherance to manufacturer' s recommendations and tolerances for equipment installation. Comprehensive, properly identified installation and maintenance records. Handling of the components. Adequate tooling and auxiliary equipment in working order. An inoperable hydraulic power unit for torque wrench or for jacking of the mill, or faulty crane can be a very costly proposition. A special area in comminution circuits are wear components. Apart from the mill liners, the wear components such as, feed chutes, rock boxes, mill trunnion liners, discharge sumps, etc. are designed to the best theoretical configuration, based on experiences in similar installations. However, each process is different to a various degree, mainly because of various types of ores and grinding requirements. Consequently the first generation of wear components is very seldom the ideal one. Based on operational experience, the shape and material of wear components should be modified, until the optimum, most economical design is achieved. SHIPPING AND STORAGE Considerable damage to the equipment can be done by careless packing, shipping or storage.

Jan 1, 1982

By ERNEST A. HERSAY

ACCURATE ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fine¬ness of the pulverized product. Fine screens are expensive, easily injured by mis-use, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to he actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

May 1, 1906

By Linda Lee, R. E. Reed-Hill, C. R. Smeal

Four fcc metal surfaces, etched to make them responsive to polarized light, have been studied with an electron microscope. Jones'prediction that these surfaces are grooved has been verified. Optical-goniometer measurements made on commercially pure nickel indicate that the groove walls are poorly defined (100) facets. Surface mientations close to either 4001 or {ill).- show no extinctions on the polam'zid-light microscope. An explanation is offered for this orientation dependence. It has also been deduced that polarized-light extinctions on a grooved cubic-metal surface should not be used directly in crystallographic-orientation determinations. The nature of the etching solutions that produce these surfaces is considered. A cubic-metal surface may be made responsive to polarized light in two basic ways."' In one, an anodic film, believed anisotropic, is formed on the surface. A plane-polarized-light beam, at normal incidence, should be reflected from this type of film with an ellipticity that varies with grain orientation. Under crossed polarizers of a polarized-light microscope, each grain may be distinguished from its neighbors by a difference in reflected-light intensity. An alternate treatment,' more generally applicable to cubic metals and of principal concern here, involves etching of grain surfaces. The characteristic features of this surface were first deduced by Jones3 from light-microscope observations. She concluded that, in general, grain surfaces were furrowed so that light was reflected from two parallel sets of etched facets. A grooved surface produces elliptical polarization of a plane-polarized beam because the beam does not strike groove walls at normal incidence. Jones also observed that the furrows must have faces inclined to each other by approximately 90 deg, since the light returns along the incident path, and that a grooved surface should show four maxima and minima of reflected-light intensity during a 360-deg stage rotation of the polarizing microscope. Positions of maximum extinction were predicted to occur when groove axes were parallel to either polarizer or analyzer vibration directions. Because of the limited resolving power of Jones' optical microscope, her deductions were primarily indirect. Proof of the correctness of her conclu-sions, as demonstrated by the electron microscope, will be given as well as evidence concerning the crystallographic nature of the etch furrows and the types of etching solutions that produce them. EXPERIMENTAL PROCEDURE During a comprehensive study of hot plastic deformation in nickel and nickel alloys, an etch was evolved that produced a surface with an excellent polarized-light response on Nickel 200 ("A" Nickel). The etching solution and associated metal-lographic procedures are given in Table I. In evaluating this etch, a study was made of the topological features of the etched surface and their relation to the underlying crystalline structure. As part of this investigation, large crystals (2 mm average diameter) were grown in a 1-cm-sq Nickel 200 specimen. After the surface was etched, the crystallographic orientations of ten grains were determined by the standard back-reflection Laue technique of Gren-inger.4 Maximum extinction positions during a microscope stage rotation were also measured for the ten grains. Groove-wall positions on the surfaces of the ten grains were measured with a two-circle optical goniometer. The technique was essentially that of Barrett and Levenson.5 Several grain surfaces were photographed with a Philips Model 100A electron microscope. All specimens were replicated with collodion, or collodion backed with formvar and chromium shadowed at 18 to 20 deg. The basic material was Nickel 200. However, an electron-micrographic study was also made of surfaces developed by polarized-light etches on other fcc metals (90-10 a brass, Monel 400, and lead). All etching procedures are given in Tables I and 11. EXPERIMENTAL RESULTS Fig. 1 shows typical electron micrographs of three different fcc metal specimens and an optical micrograph of a fourth. All photographs show a grooved structure corresponding closely to Jones'3 predictions. Also, as noted by Jones, extinctions were always observed when groove axes were either parallel or perpendicular to the microscopes' vertical cross hair. The symmetry of the grooves, with respect to the twin boundaries in Fig. 1, implies that furrows have a crystallographic basis. The coarse-grained Nickel 200 specimen was used to study this basis. Facet Orientation. The poles of the ten Nickel 200

Jan 1, 1964

By Bai Shiwie, Li. Guangyu

This paper presents the study in situ on stress field of rock mass in a large dam site. By means of two different measure instruments and the method of stress relief, a lot of measure in situ has been done, including stress measurement of three dimensions at ten points and two deep-hole stress measurements in the perpendicular boreholes which are 59.4m and 53m deep seperately, and the basic accordant results corresponding two methods have been got. In the process of the deep-borehole stress measurement we got the stress value in critical state in which cylindrical core would become core-disking in the high stress area, which was first got in the world. The maximum principal stress was up to 650 kg/cm2. The stress value obtained by test and the thickness of rock disks all basically accord to the analysis by mechanical mechanism of core-disking The plane linear elastic finite element analysis has been completed. Results of inverse calculation all ac- cord to the measurement results in four different positions. The whole outline of the stress field of dam site was delineated clearly.

Jan 1, 1982

By E. V. Murphree

CREATION of atomic energy, aside from its influence on war or peace, has posed these basic questions for the world: How soon can energy from atoms be harnessed to do man's daily work? How much of this power will there be, to what degree will it supplant present fuels, and what does it imply for the future of civilization? Answers to these questions may be found in part in analysis of just what atomic energy is and how far its development has come. The answers are encouraging. One of the first questions encountered in considering the application of atomic reactions is whether such reactions can be controlled. Fortunately, this has been adequately demonstrated by the operation of the Government plutonium plants at Hanford, Wash. Here nuclear reactions are carried out on a large scale involving liberation of about a billion B.t.u. per hour. This hourly heat liberation is equivalent to that obtained from about 7100 gallons of fuel oil. It has been possible to operate these plants day in and day out with the reaction controlled at the intensity desired. There should therefore be no question that, under proper conditions, reactions involving nuclear fission can be controlled.

Jan 1, 1946

By AIME AIME

WEST TEXAS, New Mexico and Northern Mexico form one of the most interesting regions in America for geologists and mining men and are full of points of historical and human interest for others. Including as the region does, a representative portion of the high plateau of Mexico, the front range of the Rocky Mountains and the great down-dropping plains of Texas, there is variety as well as interest in the geological and mining problems there to be studied. Gold and silver mining were the pioneer industries and are yet of high rank in importance. Among the papers to be presented at the El Paso meeting of the Institute this month will be two dealing with silver mining and ore treatment at the Shafter mine in Texas, that most un- usual property which has for so many years been the largest mining enterprise in its region. West Texas is now better known for its petroleum and gas, and in another paper will be described the problems involved in uding natural gas for smelting at the well-known El Paso smelter of the American Smelting and Refining Co. In still other papers, presented at the session sponsored by the West Texas Geological Society and cooperating organizations, the general geology of the region, the potash and the sulfur deposits will be de- scribed. At El Paso the refineries of the great com- panics will be available for visits.

Jan 1, 1930

By E. J. KENNEDY

THE annual dinner-dance was held in the large ball room of the Commodore hotel Wednesday evening. A total of 577 were seated at the dinner, over which President Eavenson presided as chairman and toastmaster. In introducing George C. Stone, the James Douglas Medalist, W. R. Ingalls outlined the former's association with the zinc industry. He said, in part In designing and building Palmerton, Stone erected a metallurgical monument and won the title of chief engineer of the New Jersey Zinc Co., with transferal to its New York office in 1900. There lie held forth in dignity, efficiency, and with appreciation until his retirement from active service in 1929. After a few years lie was diverted from the position of chief engineer for his company to the superior one of chief metallurgist and that gave to Stone his next big chance.... This was the conception of a research department and the ability to persuade his directors to adopt it. I shall not pretend to summarize the great things that afterward developed. I shall mention only the institution of the manufacture of lithopone in this country, the charging of the Wetherill furnace with briquets, the mechanicalization of the Wetherills, the accomplishment of continuous distilling, and most recently the introduction of reflux-refining.

Jan 1, 1935

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905

By Leonard A. Wood, A. G. Winslow

Subsidence has occurred in several areas of the upper Gulf Coast region of Texas, although in most cases this is not evident without precise instrumental leveling. As referred to in this report, the region com- prises about 7200 sq miles of the Gulf Coastal Plain and includes all or parts of the following counties: Harris, Fort Bend, Waller, Brazoria, Galveston, Liberty, Chambers, Orange, and Jefferson (Fig. 1 ). Topographic relief is low, ranging from sea level at the Gulf of Mexico to 300 ft or more in northwestern Harris County.

Jan 10, 1959

By J. P. Hirth, C. S. Hartley

A simple graphical technique is presented for rapidly determining the ratio of resolved shear stress on slip systems in single crystals to the applied stress (Schmid factor) for various simple states of stress. Master plots are presented which, when used in conjunction with an appropriate stereo-graphic projection, allow one to determine the Schmid factor for all slip systems in a crystal of given orientation. It is shown that one such plot suffices for simple tension or compression, flex-ural bending, and biaxial compression, while a combination of two different plots must be used for torsion and simple shear. STUDIES of the deformation behavior of single crystals are most valuable when the applied stresses are resolved onto the various slip systems of the crystal. A careful study of the available slip systems and proper selection of the state of stress used and the specimen orientation can then yield quantitative information about the probability of specific dislocation reactions, the strength of barriers to plastic flow, and the mechanisms of yielding and flow in general. It is the purpose of this work to analyze some common states of stress used in deformation studies and to present a simplified way of determining for these cases the ratio of the resolved shear stress on the slip systems to the applied stress (Schmid factor). I) CALCULATIONS We first define two orthogonal coordinate systems: one based on the specimen geometry (a right circular cylinder of radius, R, is considered here) and one based on the particular slip system of interest. The unit vectors and angles specifying the two coordinate systems and the relationship between them are listed in Table I. The relationships among the various angles and unit vectors are shown on a stereographic projection in Fig. 1. The transformation matrix between the (XI X2 X3) and (x'1 x'2 x'3) system is x1 x2 x3 X'1 a11 al2 a13 x'2 a21 a22 a23 x'9 a31 a32 a33 where in this case the direction cosines aij are given by a11 a12 a13 aij = a21 a22 a23 a31 a32 a33 sin 0 cos F cos 0 sin F cos 9 = -cos 0 cos F sin 0 sin F sin 6 [1] 0 -sin F cos (p In terms of Eq. [I.], the stresses sij, referred to the slip system, are determined from oij, referred to the specimen axes, by1,2

Jan 1, 1965

By Winston W. Spencer

ALTHOUGH by far the largest A consumer of platinum metals in the world, the United States until recently has been in- significant as a producer. Writing in the "Minerals Yearbook" for 1939, H. W. Davis states that 1938 probably marked the beginning of an- other period of transition in the world production of the platinum metals. In that year, he says, their production in the United States jumped to 49,380 oz., or fourth in the rank of world output. In the ten-year period 1925 to 1934 United States output ,averaged only 8300 oz. Practically all of this sudden in- crease in production is attributable to the introduction of mechanized equipment at the placer deposits in the Goodnews Bay district of Alaska. This district adjoins the Bering Sea and Kuskokwim Bay (accented on the first syllable), and is approximately 120 miles south of the mouth of the Kuskokwim River. The nearest village and post office is Platinum, which lies about eleven miles north- east of the Goodnews Bay Mining Company's camp. A good gravel road connects the mine camp and the village.

Jan 1, 1940

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Processes in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carborization. MECHANICAL PICKERS Machines utilizing shape, fictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1, 2 Taggart, 3 and Peele. 4 Shape In general, coal differs in shape from its accompanying dirt throughout the range of commercial sizes. Coal, breaking into roughly, cubical particles, contains a greater number of axes that are approximately the same length than does the dirt. The latter, consisting of pieces of slate and shale and lenses of pyrite, is flatter in nature. Further, flat coal often has a dirty, slaty appearance, even though of high quality. Mechanical pickers known as flat pickers, or "flatters," are widely used in the Pennsylvania anthracite region to remove flat coal from the final clean coal. This practice greatly improves the appearance of the final market product.

Jan 1, 1943

By Hermsdorf, Richard P. E.

AMONG the newer lead smelting and refining plants of the country is that of the United States Metals Refining Co., at Carteret, N. J. Not only is the technical practice here modern and efficient, but exceptional care is taken to assure healthful operating conditions for the employees. One large building houses the entire department, which includes, as its chief units, one reverberatory smelting furnace, one blast furnace, two softening furnaces, one utility reverberatory furnace, two Faber du Faur retorts, five 120-ton kettles, three 60-ton antimouial lead kettles, and one 5-ton kettle for experimental purposes. There is a 10-ton overhead crane in the kettle aisle, which is also used for shipping lead. Other auxiliary equipment is referred to in the outline of operations. A general plan of the plant is shown in Fig. 2, and a general view in Fig. 1. Primary smelting operations are conducted in a 30 by 11-ft. reverberatory furnace with bottom, roof, and upper walls of clay brick, magnesite

Jan 1, 1934

By A. V. Bradshaw, R. I. L. Guthrie

The behavior of large bubbles in the size range 4 to 25 cm3, rising through molten silver, has been studied. It was found that rising velocities were equivalent to those in aqueous systems of low viscosity. Mass transfer coefficients for oxygen bubbles dissolving in silver were found to be 0.036 ± 0.007 cm sec-1, being close to those predicted for transfer through the front surface of the spherical cap bubble only. It is suggested that the surface active nature of oxygen in silver could account for the relatively low coefficients obtained. MANY metallurgical processes involve interactions between gas bubbles and liquids. Examples include the removal of carbon monoxide in Open Hearth Steelmak-ing, the removal of sulfur by blowing air through copper matte during converting, and the removal of hydrogen from steel during vacuum degassing or inert gas flushing. The steps involved in such refining processes include; transport of the dissolved species to the bubble interface, adsorption and chemical reaction of the species at the interface, desorption of product molecules from the interface, and transport of product gas into the bulk gas phase of the bubble. It has been concluded1 that all the interfacial steps involved proceed so rapidly at steelmaking temperatures that transport of the solutes, present in the metal, become the important rate controlling factors provided nucleation phenomena are not restrictive. The O-Ag system was chosen for the investigation into gas bubble-molten metal interactions due to the relatively high solubility of oxygen that enables rates of oxygen transfer to be measured from changes in bubble volume. Other advantages of this system include the absence of a stable oxide phase at an oxygen pressure of 1 atm and the relatively low melting point of the metal which permits the use of a metallic container, providing that it is resistant to oxidation. In those metallurgical processes where bubbles have an important influence, bubble volumes are usually greater than 5 cm3. For this reason the present study relates specifically to single large bubbles of oxygen rising in silver. These bubbles adopt the characteristic spherical cap shape similar to that shown in Fig. 1 for a 30 cc bubble rising in water. After an initial investigation to determine the velocities of inert (nitrogen) bubbles rising in molten silver, experiments were carried out with oxygen and the rates of mass transfer between the oxygen bubbles and the silver were measured. EXPERIMENTAL Apparatus. The apparatus, Fig. 2, for containing molten silver, was constructed from "Nimonic 75" Alloy (75 pet Ni, 20 pet Cr, 5 pet Fe, Mn) and provided for the release of single bubbles from an hemispherical cup, situated at the bottom of the column. The cup was turned by translating the rotation of the drive shaft through 90 deg. This was accomplished by the use of a bevelled gear system, and a smooth drive was provided by the lubricating action of the silver on the gears. Since reliable high temperature seals at 1000°C were found to be impracticable, the filling and drive shaft tubes were extended outside the 3.5 kw resistance wire tube furnace, where connections were made using easily accessible O-ring seals. The apparatus remained gas tight to the atmosphere at pressure differentials far in excess of those used. The filling tube was connected via a small bore tube to the differential pressure transducer. Gas could be bubbled into the inverted cup from two i-in. tubes which passed down the inside of the column to preheat the gas. The temperature of the silver was maintained at 1020°C during all experiments. Measurement of Bubble Volume. In order to calculate mass transfer rates, it was necessary to obtain a continuous record of the bubble's volume during its passage through the column of molten silver. The method adopted for measuring the bubble volume involved closing off the top gas space to the atmosphere prior to each experiment, and recording the variation in gage pressure of this space during the formation and rise of the bubble. Since any change in bubble volume results in an equal change in top space volume, Boyles Gas Law may be applied (for isothermal con-

Jan 1, 1970

By WILFRED SYKES

THE story of the rolling of strip steel is not limited to any one plant or individual or group of individuals. It is a story with many ramifications. First of all, it should be understood that the strip mills we are considering are continuous mills, in that the steel passes directly from one mill to the other in a more or less straight line. Continuous mills are not new; in fact, they have been used for many years in the rolling of a few simple shapes. They were, however, driven by one motor through jackshafts, and as a result the speed of each roll stand had a fixed relation to that of every other stand in the series. This in turn fixed the reduction that could be made in each stand. The mill could produce simple things, but was not satisfactory for the production of the variety of strip now required. It was, therefore, necessary to get away from the restrictions of that kind of drive. To accomplish this, the designer could either separate

Jan 1, 1936

By C. E. McWhorter

IN underground mining recent trends toward mining large tonnages of low-grade ore have created, among other things, a need for cheaper and more flexible ore transport. A relatively new development has been the adaptation of shaker conveyors to meet this need. Although widely used in coal mining, only in the last few years have shaker conveyors been used in underground metal mining. The equipment consists of a driving engine, either electric or air powered, upon which is mounted a drive trough supported in ball-bearing frames. The trough line, or conveying medium, is made up of a number of sections, each section connected to another, usually with bolts. The length of each trough section is controlled by the length that can best be handled underground, but is usually from 9 to 13 ft over-all. The length of a complete conveyor line is determined by the character and weight of material to be handled as well as by the size of the ore body. Trough lines vary in lengths from 100 to 300 ft and the trough has a cross-section area of 127 sq in., and is 22 in. wide by 6 ½ in. deep.

Jan 1, 1948

By C. L. HUNTZINGER

THE mine here described is in the Witbank district, a coal area of the Transvaal, about 100 miles north- east of Johannesburg. and is owned by the Witbank Colliery, Ltd. The plant has a capacity of 4000 tons per eight hours, and prepares five sizes of coal. The coal seam lies at a depth of about 200 ft. below the surface, and is reached by an inclined shaft sunk at an angle of 18° with the horizontal. Although the thickness of the coal seam varies from 10 to 14 ft. or more, only about a 7-ft. bench is mined. Mining is by the hord and pillar system. Bords are driven 18 ft. wide, with pillars measuring 18 ft. square. The mine is laid out into four sections, each sewed by a main haulage way from the shaft. Arc-wall machines are used for cutting the coal. but all loading is done by hand. Native labor is employed under the supervision of white miners, who do the required blasting. The workings are practically free from gas and water, and very little timber is needed.

Jan 1, 1931

By A. Ross Rornmel

ABILITY to speak effectively is one of man's most longed for and coveted abilities. It is the ability to stand on one's feet, transfer knowledge and thoughts to others, to reach an objective professionally or otherwise by leading groups through a channel of planned thought. Each day group speaking plays an important part in making or marring success, and the engineering profession often provides this opportunity and requirement. An ability to speak effectively develops courage, poise, confidence, and prestige for the speaker. The technical man cannot be reluctant to face an audience. He is often called upon to do this in presence of employees, supervisors, and other groups. His ability to speak effectively is as much a requirement as the fundamentals of his profession. The three fundamentals of effective speaking are: (1) Enthusiasm and Confidence. These are joined because of their close relation. (2) Preparation. This includes knowledge of the subject. (3) Presentation. By this is meant the features of delivery.

Jan 1, 1946

By M. E. Glicksman, G. S. Ansel

It has been shown by Walton and Chalmers,&apos; that the mechanism of the development of solidification textures in castings involves the preferential growth of dendrites along certain crystallographic directions as determined by the influence of prevailing heat-transfer conditions. Specifically, this growth is parallel to the direction of heat flow. The purpose of the present investigation was to determine the applicability of this mechanism to: 1) commercially pure aluminum (99.75 pct) solidified to coarse columnar crystals, 2) an aluminum-silicon casting alloy (5.25 Si, 0.38 Fe, 0.02 Cu, 0.10 Ti, 0.002 S) cast to a fine-grained structure under complex and reproducible heat transfer conditions. PROCEDURE AND RESULTS 1) Specimen Preparation—Using a technique similar to that employed by Northcott and Thomas,2 samples were melted in the directional solidification mold, Fig. 1, by heating the entire assembly to 670° C. The mold was then end cooled using a water jet. From considerations of harmonic analysis, the likely distribution of isotherm normals encountered by the growing crystals is shown in Fig. 1. 2) Orientation Analysis—The pure aluminum sample froze to large columnar crystals, nucleated close to the metal diaphragm, with the growth direction parallel to the mold axis. Using the back-reflection Laue technique, the growth direction of these crystals was determined to be a <100>, which coincided within 53 deg to the mold axis. Metallographic examination of the relatively fine-grained aluminum-silicon sample revealed a dendritic mode of growth having its primary dendrite arms along isotherm normals. Back-reflection Debye-Scherrer patterns, taken with the specimen rotating about its cylinder axis, yielded rings displaying symmetrical arcing, thus proving that the sample did, indeed, possess the solidification texture inferred from the preliminary metallographic examination. To determine the extent and orientation of the texture in the aluminum-silicon alloy, a density distribution of the (111) poles of the sample was plotted using the transmission Debge-Scherrer

Jan 1, 1960

By Colman Goldberg

IT is customary to plot crystallographic planes or axes on a Wulff stereographic net which is ruled with parallels of latitude and meridians of longitude. If a single crystal is placed at the center of a sphere, the coordinates of a crystallographic plane or axis are the coordinates of the point where the axis intersects the sphere. The standard (HKL) projection is the projection for which the sphere is rotated so that the (HKL) pole is at the center of the projection. Schiebold and Sachs&apos; and many others have published standard projections for the more important planes of a cubic crystal. With Tables I and 11, it is possible to plot any plane (HKL) of a cubic crystal on a standard (001) projection if the absolute values of the individual H, K, and L are nine or less, which is almost always the case. Using the methods outlined by Barrett,&apos; the standard (001) projection can be rotated so that any arbitrary plane is at the center of the projection. The tables are believed to be important for two reasons: 1—The heretofore published standard projections usually are not of the proper size to fit the stereographic nets available. With these tables a standard projection can be made which will be of exactly the proper size for the available stereographic net. 2—With the tables, planes that do not appear on the previously published standard projections can be easily plotted. For these reasons, the tables are especially useful in the study of optical reflections from etched surfaces and can also be used to make a standard projection for the axis which is normal to the macroscopic surface. (This axis can be found by X-ray or optical methods.) Then if the crystal is etched, the effect of the etchant can readily be determined by comparing the latitude and longitude of the reflecting planes (as determined with an optical goniometer) with the standard projection that has been prepared. Use of the Tables Fig. 1 shows the meridians and parallel which have been designated as zero longitude and latitude. The tables themselves are self-explanatory. The

Jan 1, 1953