Search Documents

By Rex B. McLellan, M. L. Rudee, T. Ishibachi

A modelfor dilute quasi-regular interstitial solid solutions is proposed in which the solute atoms can occupy both the octahedral and tetrahedral interstices in the bee solvent lattice. The distribution function, according to which the solute atoms are apportioned between the two kinds of sites, is calculated. The partial thermodynamic functions of the solution are calculated from the distribution function. It is shown that such a solution model can explain the deviation from linearity of the Arrhenius plot of the temperature variation of the diffusivity of carbon through a iron. The published difiusivity data is analyzed to obtain numerical values for the distribution function. Finally it is shown from the numerical values of the distribution function that the possibility of dual-site occupancy will have a negligible effect on the solution thermodynamics for this system. DeSPITE the large amount of experimental data available on the thermodynamics and diffusion kinetics of dilute solid solutions of carbon in a iron, many of the elementary properties of these solutions are not understood due to real or apparent discrepancies in the experimental data. Basically there is a lack of agreement between the solubility and diffusion data obtained by anelastic damping techniques and by bulk chemical thermodynamic methods. SPecifically the heat of solution of cementite in ferrite estimated from thermodynamic measurement1, 2 is about twice as high as that determined from anelastic damping measurements.3 Furthermore the diffusion coefficient D of carbon in a iron in the range -40" to about 150°C (covering about ten orders of magnitude) determined from anelastic damping techniques is such that an Arrhenius plot of In D vs 1/T is linear. However in the range of about 300o to 850°C where mass flow measurements of D have been made (covering about four orders of magnitude), although the data merges with the low-temperature data, the Arrhenius plot departs from linearity. The object of this paper is to present a more refined model of dilute ferrite solutions in which the solute atoms can occupy two kinds of interstitial sites. The experimental data is analyzed in the light of this model and it is believed that thereby some of the anomalies can be resolved. snoek4 explained the room-temperature internal-friction peak (usually referred to as the Snoek peak) in iron as the stress-induced ordering of interstitial carbon and nitrogen atoms occupying the octahedral (0, 0, 1/2) interstices in the bee lattice. From the consideration of a hard-sphere lattice model the (0, 1/4, 1/4) tetrahedral interstices are larger than the octahedrons but their symmetry would not produce the strain dipole necessary to give rise to the Snoek peak. Thus the presence of the Snoek peak is direct evidence that the octahedrons are occupied. Since the publication of Snoek's explanation, most workers have assumed that all of the carbon and nitrogen in the a solid solution was located in the octahedral sites. This assumption of universal octahedral occupancy has been implicit in the theory of wert5 for interstitial

Jan 1, 1965

By Eric K. Albert, J. Kiusalaas

The paper presents an overview of SPASID (Kiusalaas and Albert, 1983), a new computer program developed under U.S. Bureau of Mines funding for the prediction of surface subsidence caused by under- ground mining operations. The presentation, which is illustrated with two case studies, also re-evaluates the influence function method as a tool of subsidence prediction, arriving at some rather unconventional recommendations. SPASID consists of four modules that communicate through common data bases: (1) Preprocessor. This module prepares and maintains the database for the entire site. The database contains all the information about the site and the mine operation that is necessary for the computation of subsidence. (2) Subsidence Predictor. The influence function method is used to predict the surface displacements that occur in any portion of the site that occur between two given dates. The computations take into account the time lag between extraction and displacement, and the effects of pitching seams and incomplete compaction at the edges of panels. The program contains i not he's influence function and the Green's function of transversely isotropic elasticity theory. (3) System Identification. The purpose of System Identification is to determine the optimal values of the various parameters associated with the influence functions in the Subsidence Module. System Identification requires measurements of subsidence from a site with a sirnilar overburden structure. The values of the subsidence parameters are obtained by minimizing the discrepancy between the measured and computed surface displacements. (4) Postprocessor. The Postprocessor is a graphics facility for displaying the data generated by the other program modules.

Jan 1, 1984

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ANDREWS, CLARENCE W., 2d Lieutenant, 12th Batt. Infantry Replacement Regiment. ANDREWS, JOSEPH C., Ordnance Dept., U. S. A. ARLUCK, A. A., Headquarters, 1st Corps of Artillery, A. P. O.. No. 759, A. E. F.

Jan 9, 1918

By Betty J. Laswell, Gerald W. Laswell

The stepped-up pace of US open-pit and surface mining during the 1970's is a direct response by mining firms and equipment manufacturers to rising costs and declining ore grades. In the race for bigger and more efficient machines, rotary drills have emerged as the foremost leader in primary drilling at major US surface operations. At least 12 different manufacturers now offer rotary rigs in the 102- mm-diam. (4-in.) or greater blasthole size range. With capital investment for the larger units quickly approaching $1 million, the question is asked, "What's been the performance record to date of rotary drill rigs operating in North America?" To answer that question, a comprehensive study of rotary blasthole drills was conducted which qualitatively reveals various problem areas inherent in the rotary drill market and indicates some new directions for improvement.

Jan 6, 1978

By L. J. West, R. M. Perrry

This chapter describes the rock mechanics studies performed for a high cut at a nuclear power station in Pennsylvania. Two units presently are being constructed on the Susquehanna River. When these units are completed, they will generate approximately 2100 MW of electricity. It was necessary to excavate about 1 million cu yd of rock to prepare the site. This excavation resulted in a high cut on the west and north sides of the station area with a maximum height of about 200 ft. The location of the high cut with respect to the plant facilities is shown on Fig. 1. The recommended slope angles ranged from 1 ½ (horizontal) to 1 (vertical) for the upper residual soil to ½ to 1 for the deeper competent rock. Because of the significant height of this cut and the fact that the slope is immediately adjacent to the proposed nuclear facilities, extensive stability analyses were performed prior to, during, and after excavation to evaluate the steepest angle at which the slopes could be safely cut. The studies consisted of evaluating both qualitatively and quantitatively all apparent factors which could affect the stability of the slopes. These factors include the strength of the material, the zones of weak material which are present along the planes of schistosity, the prominent joint systems, the ground water, and postulated seismic effects. FIELD AND LABORATORY STUDIES A comprehensive program of field explorations was performed to evaluate the geologic characteristics of this site. This program consisted

Jan 1, 1970

By W. L. Zeigler

DURING the middle 1880s, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddies. Later Wilfley tables took the place of sand jigs and vanners superseded the buddies. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. TAILINGS DISCHARGED INTO STREAMS From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1947

By Joseph B. Umpleby

PROGRESS in the petroleum industry in 1929 has been characterized by outstanding accomplishments in the fields of new discovery of supply, economic control of production, increased efficiency and reduced costs of recovery, and lowered costs and greater flexibility in manufacture. Resources have been developed in an outstanding degree in the Kettleman Hills. California, the Oklahoma City field (which adds a large potential area in central Oklahoma), the discovery of Woodbine sand production in East Texas, and the discovery of Wilcox sand production in west-central Kansas. Engineering technique has progressed both along the lines of development and production, with a net result that costs have been reduced and extraction increased in notable degree, although it is impossible to give a close measure of either. In the field of re- fining crude oils variations to the end of promoting reduced cost and greater flexibility has been more important than genera! acceptance of innovations in practice.

Jan 1, 1930

By William J., Coulter

IN the early days of Colorado mining, between 1880 and 1900, when Leadville, Kokomo, and Robinson were boom mining camps, the entire area around Climax for a matter of fifteen miles was overrun with prospectors, so the mineralized outcrop at Climax was not unknown. The principal interest in minerals during this period was in gold, silver, and lead, and since the Climax outcrop showed none of these it drew little attention. Geology played an important part in bringing prospectors to the very edge of the Climax deposit. The Mosquito fault, which crosses near the base of Bartlett Mountain, continues as an important geological structure, at least as far as Leadville some twelve miles distant, and at the base of Bartlett Mountain the vertical throw on the fault is estimated to be between 2000 and 5000 ft. The sedimentary beds known to the Leadville district are all present on Bartlett Mountain to the north of the Mosquito fault, which cuts them off abruptly, and exposes the Pre-Cambrian rocks that underlaid them, so the prospectors, who were searching for gold, silver, and lead in the sediments

Jan 1, 1946

By Robert T. Chapman

The revolution in equipment for blasthole drilling, ore loading, and ore hauling has been so rapid over the last ten years that it has generated an important new profit potential in the mining industry. With the new high-capacity machinery now available, it is possible for a mining enterprise to earn a profit from larger and lower grade orebodies than ever before despite the ever-increasing burden of rising costs. Just what such equipment can accomplish when coupled with improved mining practice has been demonstrated with startling success at the No. 1 mine of Minerva Oil Co. near Cave-in-Rock in Hardin County, Ill. The No. 1 is an underground operation which has been producing fluorspar and zinc ores and concentrates continuously since 1944. A few years ago, when the mine neared the familiar cross-roads where rising costs, increasing tonnages, and relatively static product prices converge, company officials decided to bolster the operation with new mobile equipment. They chose three machines which proved so effective that output at the No. 1 doubled between 1963 and 1965,while costs dropped by about 40% in the same period.

Jan 11, 1966

By J. M. Davey

Lead-zinc sulphide ores at Mount Isa are currently treated at the rate of 180,000 long tons per 28 day period in the No. 2 Concentrator of Mount Isa Mines Limited. Prior to June 1966 lead-zinc ore was treated in part of the No. 1 Concentrator up to a rate of 70,000 long tons per period. Since 1955, two major changes in ore type being processed have occurred. Because of these changes, problems arising from treatment of the ore have altered and during the period several major changes in practice have been advocated and experimentally tested. Most of these flow sheets were developed with a view to overcoming one major problem in the ore. These were invariably abandoned as the Mount Isa lead-zinc ore contains a number of equally major problems all of which must be overcome in the treatment process. MINERALOGY The orebodies are situated in the Mount Isa Shale Group which is Proterozoic in age (Carpentarian System). The sediments consist dominantly of fine grained dolomitic, quartzo-feldspathic shales and siltstones. Specifically, the Mount Isa orebodies lie in the Urquhart shale formation which is characterised by sediments of high albite and orthoclase content denoting a large volcanic component. The Urquhart shales are approximately 3,500 feet thick and extend at least north and south of Mount Isa for 20 miles in each direction. In the area of the silver-lead-zinc orebodies the Urquhart shales are highly pyritic and have a relatively high carbon content. The

Jan 1, 1970

By M. Hoch

Equations are derived from statistical considerations to represent the activities of each component of an interstitial solution, and of a compound with a wide homogeneity range as a function of composition and temperature, based on the interaction energies between the various components, Eij. The equations are checked on the binary systems Fe-C, Ta-H, and Y-H, the ternary systems Ti-O-H, liquid Fe-C-0, and the compounds TiO, MnO, COO, and YH,. In all cases the present model represents the experimental data well. THE aim of this paper is to derive from statistical considerations the thermodynamic behavior of non-substitutional solid solutions. "Nonsubstitutional solid solution" means either an interstitial solid solution (carbon in iron, oxygen and hydrogen in hexagonal and bcc titanium, and so forth) or deviation from stoichiornetry in compounds (introduction of vacancies—removal of atoms in one or both lattice sites of compounds FeO, MnO, TiO, NbO, YH2). wagnerl and Fowler and Guggenheim considered the theory of compounds with small deviation from stoichiometry; Anderson includes larger deviations from stoichiometry, the defect being present in one component only, as vacancy and interstitial. Rees considers only vacancies in one of the components and introduces various kinds of sites for the component where the defect occurs; the various sites interact with different energies, thus giving isotherms with two or more plateaus. Both Rees and Anderson are mainly occupied in determining the limits of two-phase regions, and the defect interaction energy is determined from the critical point. Darken and Gurry5 gave a brief treatment of carbon solution in iron; Speiser and spretnak calculated the configurational entropy for binary interstitial solid solutions by assuming that each interstitial atom in the solution excludes a certain number of neighboring interstitial sites from occupancy. Use will be made of this concept later. Hoch et al treated transition metal oxides of the NaCl-type structure, and also oxygen solution in titanium.' The main aim was to determine the behavior of the activity of one of the components as a function of the composition in the single-phase region. In the present paper, the various interaction energies are discussed in detail and the similarity between interstitial solid solutions and deviation from stoichiometry in ionic compounds is shown. Both types of systems have in common that at least on one kind of lattice site only one kind of atom occurs; this gives a fixed frame to the system, permitting a much easier statistical treatment than for the substitu-tional solid solutions. (The theory is also applied to ternary systems.) The difference between an interstitial solution and deviation from stoichiometry can be explained as follows. In an interstitial solution in the pure or standard state the host atom or host structure is present alone and all the interstitial sites which are going to be filled when the interstitial atom is introduced are empty. The interstitial solution is now created by introducing atoms into this empty lattice. In the deviation from stoichiometry, both kinds of lattice sites are already occupied in a special fashion (all lattice sites occupied, or the same fraction of lattice sites empty, or one kind completely filled, the other only two-thirds). Deviation from stoichiometry removes atoms from lattice sites, adds them, or removes atoms from one kind of lattice site and introduces them on the other lattice site. Though both cases (interstitial solution and deviation from stoichiometry) lead almost to the same equations, they are treated separately. The treatment given below corresponds to the "regular solution"10 treatment of substitutional solid solutions. Speiser and spretnak's6 treatment is similar to the athermal solution in the substitutional use. a) INTERSTITIAL SOLID SOLUTIONS Theory. It will be assumed that there are N lat-tice sites occupied by the host atom (denoted by 1). Corresponding to those N lattice sites there are N octahedral and EN tetrahedral interstitial sites. If only one kind of interstitial atom is added, this in-

Jan 1, 1964

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By H. A. Doerner

The process for smelting zinc developed several centuries ago is still in use. Through the experience accumulated over this long period of time, details of the process have been perfected until there is little opportunity to make any further improvement except by a radical change in method. Such a change was accomplished by the process recently developed by the New Jersey Zinc Co. The process to be herein discussed is a still more radical departure, which has been developed to large-scale laboratory operation by the Metallurgical Division of the U. 5. Bureau of Minesl. † The reduction of zinc oxide by carbon is a highly endothermic reaction, which requires temperatures in the range 1200° to 1400' C. for even a slow reaction rate. The transfer of the heat of reaction through thick fire-clay walls, the high radiation loss in the type of furnace used, and the practical impossibility of recovering or using the combustible products of the reduction (CO) cause a deplorable waste of fuel. With the one exception mentioned, all zinc smelting is done in small retorts manually charged and discharged. Attempts to mechanize these operations have been only partly successful, and there seems to be no way to avoid or improve the uncomfortable conditions in which the work is done. The reduction of zinc oxide by methane has a relatively high reaction rate at 1000' C. At this temperature most ore residues do not sinter, and it is possible to use metal retorts. These factors make gaseous reduction especially adapted to a continuous operation and compared to reduction by carbon make possible: (1) higher rate of reaction at lower temperature, (2) more nearly complete extraction of the zinc, and (3) much better utilization of fuel and reagent. Although the reaction between methane and zinc oxide requires 105,900 calories per mole, compared to 86,860 cal. in the carbon reduction, it is obvious that much less fuel will be required to supply 105,900 cal. through 36 in. of metal at 1000' C. than to transfer 86,860 cal. through 1 in. of fire clay at 1300° C. Moreover, the gaseous products of gaseous reduction (CO and H2) can supply 183,430 cal. by complete combustion.

Jan 1, 1937

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

Problems discussed and research opportunities identified during the workshop in the major areas of 1) flocculation, 2) flotation, 3) leaching and magnetic separation are summarized below. I. FLOCCULATION Problems Practical problems caused by unintentional flocculation or dispersion were described in the papers that dealt with iron ore processing, selective flocculation, fine coal processing, phosphate processing and potash processing. Ideas generated during the discussions ranged from the very practical suggestion that a conscious effort be made to transfer knowhow from the experienced clay industry to the metals and fuels-from-slimes industry. . . , to the familiar appeals for omnipotent theoretical developments. There was surprising recurrence of some questions in many contexts. Recurring questions are emphasized here rather than commodity-specific problems because their answers would serve a wider clientele usage. There is indeed no objection and some advantage to commodity-specific research, however, provided the proposed project is planned with full cognizance of transferable knowledge in other commodities, and of the possible usefulness of these results in other areas. Research Needs Most of the questions or research opportunities can be classified into three groups: a) water chemistry, b) dewatering, and c) flocculation theory. Other classifications are possible and probably useful. In each group there is a clear need for outwardly esoteric theoretical research a clear application of that work to current practical problems. Higher priority should be given to proposals for theoretical research which explicitly show the expected ultimate usefulness of the result. Likewise, proposals for applied research should demonstrate cognizance of applicable theory. Both of these types of projects could profit from collaboration among industrial, university and government personnel.

Jan 1, 1979

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that' have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin's description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

Jan 1, 1883

By T. H. Alden

BaCKOFEN, Avery, and Turner have shown"2 that the large tensile elongation in superplastic metals is correlated with a high strain-rate sensitivity of the flow stress. At present, the reported superplastic materials are complex eutectic or eutectoid systems with a large solubility range in at least one of the terminal phases. This note describes the behavior of a solid-solution alloy (at 22°C)5,= Sn-1 wt pct Bi, which has been processed in order to produce a fine grain size.2,3,6 The chill-cast, 1/2-in.-diam ingot was homogenized for 1 week at 130°C, extruded at O°C to 0.083 in. diam, quenched within 15 sec, and stored at -196°C. Samples were warmed to room temperature 16 hr prior to mechanical testing or metallography. During tension testing at room temperature, it was found that the flow stress reached a steady-state value which depended on the imposed elongation rate and was independent of strain to an error of about ±5 pct. In Fig. 1 is plotted log a vs log e where a is the measured steady-state flow stress and i the imposed strain rate. These quantities were calculated using "instantaneous" area and length to an accuracy in the sample diameter of ±5 x 10-4 in. The log a-log 1 curve is sigmoidal. The strain-rate sensitivity, which may be given by d log old log 6,' has a maximum value of about 0.48 between i = 5 x 10-4 and 5 x 10-3 per min. The value is well above frequently measured values for metals at creep temperatures (0.1 to 0.3) and comparable to the rate sensitivity for Pb-Sn solder: which has been shown to be superplastic.2,3 Note, however, that below or above the strain rate of 10-3 per min the rate sensitivity of Sn-1 pct Bi decreases and at high rates is more nearly like that of conventional metals. The grain size of this material is relatively uniform, Fig. 2, and may be specified by an average linear intercept i.' Grain growth occurs at room temperature but after 16 hr, L = 5. Tensile elongation was measured on finer-grain-size specimens, which had been at room temperature 15 min prior to testing. After 15 min, the samples are fully recrystallized. Three strain rates, 5 x 10-3, 10-2, and 2.5 x 10-2 per min, were employed for which the measured elongations varied from 425 to 500 pct. These results would seem to justify the term superplastic, applied to this alloy, although the ductility is inferior to that of the Sn-Bi eutectic.3 The Sn-1 pct Bi alloy, which is a single-phase material with equiaxed, fine grains, is an excellent one on which to make an estimate of the Nabarro-Herring9 creep rate. According to the model of Avery and Backofen2 a substantial part of the deformation must be accomplished by N-H creep in the strain rate-temperature regime in which d log a/d log 1 = 0.5. The maximum N-H creep rate is given by9 L2kT where v is the atomic volume and D the self-diffusion coefficient. For this test v = 3.O x 10-23 cu cm, D = 1.4 e-23,300/RT = 2.5 x 10-l7 sq cm per sec,7 L = 5x 10+4 cm, T = 295°K, and a = 2000 lb per sq in. = 1.38 x 10' dyne per sq cm. The calculated creep rate is E= 4 x 10-11 per sec which may be compared with the measured creep rate at this stress, Fig. 1, of 6.7 x 10-5 per sec. The N-H creep rate is seen to be negligible. Earlier consideration2 of this question was in error because incorrect diffusion coefficients were used. The assistance of R. R. Russell in metallography is acknowledged gratefully.

Jan 1, 1967

By Nick Turner, E Walker, George C. Bowser

A fully field tested mine-wide data/communications system is presented which integrates total data acquisition, control, and instrumentation into a single system. Installations at Kitt #1 and Amonate Mines (W.Va.1 use an LSI-11 series computer which communicates with easily installed field data stations over a single twisted wire pair. Complete field test data are presented, identifying the problems and successes experienced in the development, installation, operation and maintenance of the system, and the training of mine personnel. Of particular interest is the system installed at Kitt #1 which has been in continuous use since February 1982. The paper will also deal with the application of a computer-based carbon monoxide monitoring system installed at the Amanate mine in September 1982. The purpose of that system is to monitor air quality and to provide early fire detection in the belt entry to permit the use of belt air for face ventilation.

Jan 1, 1983

By C. K. Leith

THE interdependence of nations in regard to mineral supplies has grown apace with the expanded needs of industry, with depletion of reserves, and with advances in technology. This increased mutual dependence raises many questions of foreign economic policy of special importance in our postwar planning. Realization of the urgent need for the development of a general mineral policy broadly based on national requirements led to discussions of the problem between officials of the Department of State and myself, as a result of which it was suggested that I make an informal and unofficial canvass of the views of mineral specialists of the country on foreign mineral policy.

Jan 1, 1946