Search Documents

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

By A. C. Fieldner

THE COMMITTEE on Correlation of Research held two meetings in 1931. The first was a luncheon meeting on Feb. 19, at the Engineers Club, New York, attended by eight members and four guests-William H. Bassett, past-president of the Institute; Robert E. Tally, president; H. Foster Bain, secretary; and Alfred D. Flinn, director of the Engineering Foundation. Mr. Bassett gave a short resume of the circumstances leading to the formation of the Committee and expressed his opinion that the objectives as expressed by the Committee in its first annual report were in accordance with the ideas of the Institute officials. Mr. Tally stressed the great importance of research in the mining and metallurgical industries and stated that lie believed the Institute should encourage and promote research, and that this Committee could do a great deal to foster such work in the Institute. Mr. Bain pointed out that this Committee was appointed with a view to correlating and fostering research work. in the field of the Institute's activities. This could be done in various ways, as by encouraging the divisions and committees of the Institute to hold group meetings on research, by forming research subcommittees in the Institute divisions, and by bringing together research interest in. certain projects and the fund or organization that is equipped to carry out the project.

Jan 1, 1932

By Thomas V. Falkie

The use of operation research and computer techniques in the mineral industries continued to gain acceptance during 1966. There are generally at least five sources of information for researchers and practitioners in the field: (1) Technical periodicals like MINING ENGINEER- ING, Mining Congress Journal, etc. (2) Proceedings of the Symposium and Short Course on Computers and Operations Re- search in Mineral Industries, held last year at Penn. State University and jointly sponsored by the University of Arizona, Stanford University, Colorado School of Mines, Penn. State University and the Society of Mining Engineers of AIME. (3) Various local conferences, such as the 1966 Rocky Mountain Minerals Conference held in Denver. (4) United States Bureau of Mines publications. (5) The AIME annual meeting in New York and the SME Fall Meeting in Tampa.

Jan 2, 1967

By Jeffrey W. Nelson

Predictions of creep closure for periods ranging up to more than 1,000 years are needed for designing a radioactive waste repository in a salt formation. Such long-term predictions must be based on the use of laboratory and field test results extrapolated by numerical modeling. Laboratory test results are presented which show highly variable creep behavior for salts from different sites as well as salts from the same site. Comparisons of measured creep closures against predicted closures are presented for two deep boreholes in Louisiana salt domes and for an exploratory shaft and drift in southeastern New Mexico bedded salt (WIPP). These data illustrate the significant uncertainties involved in long-term closure predictions and indicate the critical need for site-specific, in situ closure measurements over extended periods of time for repository design.

Jan 1, 1984

By K. D. Jacob

MONTANA Phosphate Produucts Co., a subsidiary of The Consolidated Mining and Smelting Co. of Canada Ltd., operates three properties near Garrison, Mont., known as the Anderson, Graveley, and Luke mines. All three are underground operations, mining the same narrow bed at points several miles apart. The Anderson, the oldest and largest of the three, has produced about 700,000 long tons since 1929. The Graveley has produced slightly over 100,000 long tons since 1940, and the Luke, acquired in 1943, is still in an early stage of development. The great bulk of the output has been shipped to the Trail, B. C., plant of Consolidated Mining and Smelting Co. for use in the manufacture of fertilizers. The phosphate seam is the basal member of the Permian Phosphoria formation. In all three mines it has a uniform thickness of 3 to 4 ft. of oulitic phosphate, with a few shaly partings. The overlying part of the formation comprises about 50 ft. of chert and the immediate footwall consists of a few feet of shale and sandstone. underlain by the Quadrant quartzite.

Jan 1, 1944

By J. J. Gilman

WHEN a zinc crystal is immersed in liquid N, and then plastically bent, it is observed that it bends a certain amount and then fractures. This fracture occurs at a fairly reproducible radius of curvature, and the radius varies systematically with the crystal orientation. Because this phenomenon provides an unusually well-defined set of fracture conditions, it is possible to examine various possible fracture criteria and select the best one. Zinc crystals of various orientations were bent about axes lying in their glide planes (0001) and perpendicular to their glide directions [1210]. The crystals were 0.150 in. diam and had chemically polished surfaces. They were immersed in liquid N, while they were being loaded on an Instron testing machine. A three-point bending jig was used to load them. Table I lists the beam radius at which fracture occurred for each orientation. Each value is the average of at least six measurements. The normal stresses on the cleavage planes, at the time of fracture, were calculated as follows: First, from the fracture radius, R,, the orientation angle, x,, of the (0001) plane at the outer fiber was calculated. If x, = angle between the (0001) and the rod axis prior to bending, d = rod diameter, and X, = angle between the (0001) plane and a tangent to the bent crystal, then1 sinX, _ 2R, sin xn 2R, + d Since the glide shear strain is given by' y ' cot X, — Xo the glide strain at fracture, x,, can be calculated. Next, it is necessary to know the tangential stress in the outer fiber at fracture. This depends on the plastic flow curve, so a series of tensile tests were performed at —196°C on another set of zinc crystals. A curve of the average resolved shear stress versus glide strain was prepared. From this curve, shear stresses, r,, corresponding to the glide strains in the bend tests were taken. These values are listed in Table I. Then the normal stresses in the outer fibres, u,, were calculated from the relation U, = r, tan X, This analysis assumes that the fiber stresses in a bent beam are the same as the stresses in simple

Jan 1, 1959

By Paul M. Tyler

HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for sub- standard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade 1 silica sand are abundant, but most of the best de- posits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a 1 factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.o.b. cost of mining and treatment may be much high

Jan 1, 1950

By K. D. Jacob

IN the decreasing order of the tonnages involved, the uses of phosphates can be grouped conveniently into three general classes, namely, fertilizer; chemicals for military, industrial, and technical purposes; and mineral feed for livestock. The quantity of phosphate used as fertilizer, principally in the form of superphosphate, has always exceeded by far that used for all other purposes, though in recent years a marked increase has occurred in its consumption for the other two general classes of uses. Prior to the present century large quantities of superphosphate, as well as a considerable portion of the production of phosphorus chemicals, score made from bone materials which were plentiful and cheap in some areas and which could be more easily processed than phosphate rock for the manufacture of chemicals. Today, however phosphate rock has almost completely displaced bone as a raw material for the manufacture of chemically processed phosphates in nearly all countries of the world.

Jan 1, 1944

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20'24'25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M'1B|28'i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown' that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By H. R. Wheeler

CREATION of a "committee on promotion of student interest in coal mining" has an encouraging implication for the coal industry. It is indicative that mining men, both in the field and in the educational centers, realize that the problems of the industry require the best talent available. Young men are being invited into coal on the premise that it needs them, that it offers opportunity for creative work and the realization of their objectives. In initiating a movement which purports to meet the objectives of any young man who spends four or five years of his life in college, the industry does so with a full realization of its obligations.

Jan 1, 1940

By Nicholas J. Grant, A. W. Mullendore, Paul Predecki

The Duwez technique of splat cooling in which a molten droplet of metal is accelerated and made to impact on a cold, highly conducting substrate was investigated.- An apparatus for producing "splat" was constructed employing an explosive powder charge to accelerate the molten metal. Transport of the molten metal just prior to impact with the substrate was studied by means of high-speed photography. The molten particles are small spherical droplets from about 1 to 50 µ diameter. The average cooling rates for aluminum, silver, and a gold alloy splatted on nickel substrates at room temperature were determined experimentally and were found to vary from 18 to 5 x 10' C per sec. The heat-transfer coeficients for pure aluminum and pure silver splats cooled on nickel substrates at room temperature were found to be 2.7 to 6.8 and 13.6 to 54.2 cal per sec sq cm 'C (2 to 5 x 104 and 1 to 4 x 18 Btu per hr sq ft OF), respectively. Solidification rates in pure aluminum and silver splats were calculated. "SPLAT cooling" is a term describing a technique for extremely rapid freezing and cooling of molten metals and alloys to room temperature or below. The technique was developed by Duwez et al.' in 1960, and after refinement2 consisted in transferring a few tenths of a gram of molten metal to near sonic velocity to strike a suitably placed cold copper surface. Upon impact, the metal spread into a thin nonuniform film called a splat, about 10-4 cm thick. The splat particles produced in this manner were thin enough in some areas to be suitable for transmission electron microscopy, without further treatment, and, together with X-ray data, yielded a variety of structures which would be classified as follows: 1) supersaturated solid solutions (increase in solubility limit), 2) metastable crystalline stoichiometric and non-stoichiometric intermediate phases ( in Au-20.5 at. pct Si and in Au-14 at. pct Sb, respectively), 3) amorphous alloys, 4) retained high-temperature phases, 5) alloys having equilibrium phases present, but with unusual, markedly altered structures. The crystalline phases present in splats were usually extremely fine-grained and had low dislocation densities. Present interest in splat cooling centers around a study of the unusual structures produced by the technique, their contribution to alloy theory, and the possibility of the development of new or unusual properties. In addition, the technique is being examined for the production of bulk quantities of new high-strength alloys for low- and high-temperature use. Although a number of alloy systems have already been investigated by the technique, relatively little is known about the mechanism of splat formation and the physical conditions encountered by the metal during solidification and cooling. The purpose of this work was: 1) to determine the velocity, shape, and size of the molten metal droplets just prior to impact with the cold substrate; 2) to try to estimate or measure solidification rates, heat-transfer coefficients, and cooling rates in splats. EXPERIMENTAL TECHNIQUE Splatting Apparatus and Procedure. An apparatus similar to the type originated by Duwez et a1.,2 but employing an explosive charge to accelerate the molten metal, was used. A "Ramset" fastening tool (a gun normally used for driving studs into concrete, steel, and so forth) was mounted vertically above a resistance-heated graphite crucible as shown schematically in Fig. 1. A splat product was produced by melting a few tenths of a gram of metal at the position shown in Fig. 1, and then exploding a powder charge in the breach. The shock wave thus generated traveled down the barrel into the furnace, ejecting the molten metal through the 0.06-in.-diameter hole at the bottom of the crucible. The ejected metal was impacted on a high-conductivity metallic substrate where it formed a splat. High-Speed silhouette Photography. In order to investigate the size and shape of the ejected, molten metal just prior to impact with the cold substrate, high-speed silhouette photographs were taken, and are shown in Figs. 2 and 3. These photographs were obtained with the aid of an Edger-ton, Germeshausen, and Grier microflash unit and a submicrosecond flash drive equipped with a variable time delay. Two types of triggers were

Jan 1, 1965

By Lucien Eaton

INCREASED mining activity during the past year has brought to light changes in mining practice and advances in technique, born and incubated in the period of depression from which the mining industry is now emerging. Although the tendency toward large output from individual mines has continued, a salutary trend is evident toward greater efficiency at small mines, in which the gold mines of Canada have led the way. Improvement in excavating machinery and washing plants for small placers has continued, and knowledge of the possibilities and limitations of this kind of equipment has increased. Greater portability through sectionalization has been the keynote. Power, shovels and draglines mounted on caterpillar treads move from one deposit to another under their own power, and floating washing plants mounted on pontoons can be taken down, moved, and set up again by a small crew of men in only a few days.

Jan 1, 1937

By J. Szekely, G. P. Martins

A formulation is given for describing the rate of expansion of spherical bubbles rising in liquids the freeboard of which is evacuated. The computer solution of the resultant differential equations has shown that, for low freeboard pressures (less than about 5 mm Hg), on approaching the free surface the bubbles expand much less rapidly than predictable from equilibrium considerations. In other words, in this region the pressure inside the bubbles will be significantly larger than the static pressure in the liquid corresponding to the position of the bubble. These theoretical predictions were confirmed by experimental work, using two-dimensional air bubbles rising in mercury. The important consequence of these findings is that the expansion of gas bubbles in vacuum degassing operations will be a great deal less than expected from hydrostatic considerations. This would lead to a significant reduction in the available interfacial area and may explain the apparent poor efficiency of many vacuum degassing units. VACUUM degassing as a treatment for liquid steel has gained widespread popularity in recent years; the number of known installations exceeds several hundred at the present time.' Although much information is available on both the thermodynamics of the system and the overall performance of various industrial units, much less is known about the fundamental aspects of the process kinetics.2-4 The basic physical situation common to virtually all vacuum degassing operations is the interaction between gas bubbles (swarms of bubbles) and the surrounding molten metal, held in a container, the freeborad of which is at a low absolute pressure. Once formed (or introduced from an external source) the bubbles will ascend, due to the buoyancy forces, and, during this ascent, a significant increase in their volume will occur. This progressive increase in the bubble volume is due to two factors: a) the continuous reduction in the static pressure acting on the bubble during its rise; and b) mass transfer into the bubble from the surrounding molten steel. In a recent paper Richardson and Bradshaw developed equations5 for describing mass transfer into gas bubbles from molten metals at reduced pressures. However, in deriving these expressions it was assumed that the pressure inside the bubble was identical to the static pressure in the adjacent liquid. In other words, the volume of the bubble was considered to be in equilibrium with the pressure of the fluid adjacent to it. This assumption, thus their analysis presented, was thought to be reasonably accurate for most of the bubble's ascent; however, it was unlikely to be valid in the immediate vicinity of the free surface, held at a low pressure. It was pointed out in the discussion6 that the region close to the surface may be of considerable importance as both the driving force and the interfacial area available for mass transfer are at their highest value here. The ' 'anomalous" behavior of gas bubbles when approaching a free surface at low pressures was recently confirmed in a preliminary investigation by Szekely and Martins. ?1 Here high-speed motion photography was used to study air bubbles rising in a column of n-tetradecane with a freeboard pressure of 0.1 mm Hg. It was found that significant distortion of the bubbles occurred on approaching the free surface; furthermore, the expansion observed was much less than what one could expect from hydrostatic considerations, i.e., factor a previously discussed. It follows from the foregoing that a detailed study of these phenomena would be justified both from fundamental considerations and because of their potential relevance to technology. The purpose of the paper is to present a more realistic formulation for the expansion of a gas bubble approaching a low-pressure region, together with a comparison of the theoretical prediction with experimental measurement. An inert bubble will be considered in the first instance; it is thought that the understanding of the fluid mechanics is an essential first step toward the realistic formulation of the mass transfer process. This latter problem will be the subject of a subsequent publication. FORMULATION The Physical Model. Consider a spherical bubble, of initial radius Ro, rising in a fluid, having a density pL. Initially let the bubble be at a distance H from the free surface, and at a pressure Pgo, as illustrated in Fig. 1. Pgo, the initial pressure in the bubble, is given by the following equation: pgo = Po = Ptp +pLgH [ la] where Po is the pressure in the liquid corresponding to the initial position of the bubble and Ptp is the pressure at the free surface. The fluid pressure at

Jan 1, 1970

By R. E. Allen

ONE of the most unusual oil field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fe Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from

Jan 1, 1933

Jan 1, 1885

By D. D. Smith, D. P. Squier, E. L. Dougherty

A system of differential equations describing the temperature behavior of fluid injected at constant surface temperature in a well is derived and .solved analytically. A formula for the fluid temperature at any time and depth is given, as well us a special formula valid for very large times. These formulas are used to calculate temperatures for several typical cases. The results indicate that, initially, the temperature of the water entering the formation is considerably lower than the injection temperature. This condition lasts for only a short period— less than three days for most cases of practical interest. Following this highly transient period, during which the temperature of the fluid entering the formation builds up to about 50 to 75 per cent of the injection temperature. the system enters a quasi-steady state in which the temperature changes are very slow. After severl years, the bottom-hole temperature will still be 50" to 100°F lower than the injection temperature, hilt the heat losses may he tolerable. INTRODUCTION Predicting the behavior of a hot-water flood requires that the temperature of the water entering the injection interval be estimated. This report describes the development and solution of a system of equations which describes the temperature behavior of the injected water in the wellbore with certain simplifying assumptions. The only previous means known to the authors for describing such a process is that of Moss and White.' Their results appear to be close to those obtained by our method in the practical cases which were compared; this agreement is largely due to the fact that in our method temperature soon approaches a quasi-steady state, as was assumed in their method throughout. However, our model covers all times, is continuous (whereas the Moss-White model depends on breaking the depth into discrete intervals) and. we feel. more closely describes the physical problem. FORMULATION OF THE PROBLEM PHYSICAL SYSTEM AND ASSUMPTIONS The injection procedure consists of pumping water at a fixed surface temperature T., down an infinitely long cylindrical well or tubing of inner radius Any material exterior to the water column such as mud, casing, or cement is regarded as part of the formation. The general behavior of the system may be described qualitatively as follows. When the hot water is first introduced into the system, the temperature difference between the formation and the water is large, resulting in a high rate of heat transfer. As a result, the temperature adjacent to the wellbore rises very quickly. Because the segment of the formation adjacent to the wellbore largely controls the heat transfer rate, the heat transfer rate will become relatively constant when this portion has reached a temperature close to that of the water opposite it. The temperature of the water and formation then increase very slowly with time. The length of the initial highly transient period and the temperature of the water at its conclusion will be functions of depth, injection rate, injection-string radius, surface injection temperature and the physical properties associated with the water-formation system. The following additional assumptions were made. 1. There is no heat transfer by radiation in the system. 2. There is no heat transfer by conduction in the vertical direction in either the injection stream or the formation. 3. The linear volumetric and mass flow rate of the water is constant throughout the injection stream. 4. No horizontal temperature gradient exists in the injection stream. 5. The product of density and heat capacity is constant for both the water and the formation, and the formation thermal conductivity is constant. 6. Initially, both the water in the wellbore and the reservoir are at a temperature given by the (constant) ambient surface temperature plus the product of depth and geothermal gradient (assumed constant). At large distances for the wellbore (r m), the formation will remain at this temperature. 7. The water temperature and the formation temperature at r — r,, are equal for all depths D. DERIVATION OF EQUATIONS The differential equation satisfied by the fluid temperature T,(D, t), which is obtained by writing a heat balance on a cylindrical differential of volume dV of the injection string between the depths D and D i dD, is

By AIME AIME

THE convention which met in Washington at the call of the Joint Conference Committee was called to order at ten o'clock on Thursday morning; June 3, by Richard L. Humphrey, temporary chairman, member of the American Society of Civil Engineers, who made a brief statement of the reason for the meeting. Lieut. Col. Charles W. Kutz, Corps of Engineers, U. S. A., and Engineer Commissioner of the District of Columbia, then welcomed .the engineers composing the convention on behalf of the District of Columbia and, the Washington engineers. Although an elaborate program had been prepared on which were many well-known speakers on interesting and important topics, , it was voted to intersperse this to fill in the usual and unavoidable hiatuses in the business program of such a convention[ Calvert Townley, president of the American Institute of Electrical Engineers, was elected permanent chairman, and J. C. Hoyt, of Washington, was elected secretary of the convention. The following committees were appointed: Consti¬tution and by-laws, Richard L. Humphrey, chairman; resolutions, Philip N. Moore, chairman; and program, F. H. Newell, chairman. Then, Gardner S. Williams, member of the, A. S. C. E. and the Grand Rapids Engineering Society of. Grand Rapids, Mich., and one-time member of the American Association of Engineers, offered the following resolutions:

Jan 1, 1920

By W. H. Emmons

A DIATREME is a hole blown through a rock by gases, presumably of volcanic origin. Not all pipes of ore have formed by deposition of metals in such openings, but a considerable number have so formed. In this paper are described peculiar vein patterns that are believed to be incipient diatremes or "perforation pipes." Grading into this group is one showing thorough brecciation without rotation of fragments and into the latter a group of ore pipes showing brecciation with rotation of fragments-many of them with well rounded fragments. Also, volcanic craters or volcanic necks are explosion pipes. These may carry ore deposits along their contacts and some carry deposits within the pipes. As new data appear this group becomes increasingly impressive. It has been shown that veins are concentrated in and about cupolas of batholiths and that such veins commonly lienearly parallel to the long axes of cupolas as these are shown on plans. It would be supposed that conical cupolas would have radial patterns, but few vein systems exhibit radial patterns. It is probable that explosion pipes also may form in areas above conical cupolas. From these the gases escape more violently because the loads above them are less than above an elongated cupola where larger bodies of rock are affected. The hypothesis is sound mechanically, for the top of an elongated cupola is a line whereas the top of a conical cupola is a point.

Jan 1, 1938

By W. H. Emmons

A DIATREME is a hole blown through a rock by gases, presumably of volcanic origin. Not all pipes of ore have formed by deposition of metals in such openings, but a con-siderable number have so formed. In this paper are described peculiar vein patterns that are believed to be incipient diatremes or "perforation pipes." Grading into this group is one showing thorough brecciation without rotation of fragments and into the latter a group of ore pipes showing brecciation with rotation of fragments-many of them with well rounded fragments. Also, volcanic craters or volcanic necks are explosion pipes. These may carry ore deposits along their contacts and some carry deposits within the pipes. As new data appear this group becomes increasingly impressive. It has been shown that veins are concentrated in and about cupolas of batholiths and that such veins commonly lienearly parallel to the long axes of cupolas as these are shown on plans. It would be supposed that conical cupolas would have radial patterns, but few vein systems exhibit radial patterns. It is probable that explo-sion pipes also may form in areas above conical cupolas. From these the gases escape more violently because the loads above them are less than above an elongated cupola where larger bodies of rock are affected. The hypothesis is sound mechanically, for the top of an elongated cupola is a line whereas the top of a conical cupola is a point.

Jan 1, 1938

By J. D. Raulerson, J. M. Williams

This paper presents a comparative evaluation of several system currently being used or proposed for the transport of matrix from an open-pit mine to a large fixed plant. The matrix is a sticky, wet clay to be carried from 8-16 km (3-10 miles) at 910 t/h to 1.8 kt /h (1,008-2,000 stph). The system is complicated by frequent moves of the open-pit mine site and other factors, such as use of the clay component in land reclamation.

Jan 1, 1984