Search Documents

By Daniel R. Shawe

Large tabular beryllium deposits in waterlaid rhyolitic tuff at Spor Mountain, Utah, contain the world's largest known resources of beryllium (as bertrandite). The district also has produced fluorspar and uranium. The largest beryllium deposit is about 2.5 miles long, and known deposits contain many million tons of material with at least 0.5 per cent BeO. The beryllium-bearing tuff (Pliocene?) underlies topaz-bearing rhyolite ( Pliocene?) that contains unusually high amounts of beryllium, fluorine, and uranium, and overlies other volcanic rocks (Pliocene? or Micocene?) and marine carbonate and elastic rocks ( Paleozoic). The deposits occur in hydrothermally altered tuff only where it contains abundant carbonate pebbles eroded from the Paleozoic rocks and where the tuff was deposited as thick layers in now-buried paleovalleys. Basin and Range faults, thrust fa ults, and possibly strike-slip faults formed in this part of the Basin and Range province during the late Tertiary, and volcanic rocks were extruded. Beryllium mineralization probably occurred during this episode. Undoubtedly the beryllium deposits are related genetically to the topaz-bearing rhyolite, but the details of their genesis are not certain and probably are complex. Beryllium deposits are close to major faults, and locally the beryllium is concentrated at faults, indicating fault control of mineralization. Some elements in the deposits, such as lithium, however, are evenly distributed in certain Luff beds and perhaps were introduced prior to faulting. Still other elements, such as manganese and lead, were concentrated in the beryllium deposits and subsequently were leached along late fractures, indicating a period of metal redistribution following mineralization.

Jan 1, 1968

By P. L. Russell

The use of nuclear explosives for excavation has been demonstrated to be feasible and practical. Application of nuclear explosives for overburden removal from large ore deposits appears to offer economic advantages over present methods, but under the present pricing schedule, high-yield devices must be used to obtain an economic advantage. The use of nuclear explosives presents problems not inherent in the use of conventional explosives, and thus they can be used only in areas where large explosions and associated phenomena can be tolerated. Stripping of coal with nuclear explosives does not appear practical at this time, but stripping overburden from copper or iron ore deposits may be a potential use. Even here, however, the use of nuclear explosives would require isolation, favorable topography, favorable ground-water conditions, and a low population density. If these basic requirements can be met, the use of nuclear explosives for overburden removal would offer both economic and time advantages. The possibility of using nuclear explosives for peaceful purposes was a subject for speculation as early as 1945. The PLOWSHARE Program was formally established by the AEC in June 1957 for the purpose of developing and demonstrating peaceful applications for nuclear explosives. The technical direction of the program is the responsibility of the Lawrence Radiation Laboratory, Livermore, Calif. Mining and excavation were two fields that received early consideration as areas in which nuclear explosives might be used. Knowledge gained from underground weapons testing increased this possibility, and the development of the thermonuclear device which has a small fission-to-fission ratio, reduced the hazard of radiation, and spurred interest. Nuclear explosives appear to have the greatest potential in the following mining operations: 1.— Surface Mining a) Stripping of waste for open-pit excavation b) Breaking of ore in open-pit mining c) Quarrying d) Blasting for production of aggregate, riprap, etc. 2. — Underground Mining a) Block caving application b) Crushing of ore for in-situ leaching, etc. c) Preparation of underground waste disposal areas Of the potential applications, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. REMOVING OVERBURDEN IN OPEN-PIT MINING Removing the overburden is one of the largest jobs in open-pit mining. In 1960 open-pit mines produced approximately 130 million tons of coal, 108 million tons of copper ore, and 135 million tons of iron ore. To obtain this much production, an estimated 3-billion tons of overburden were removed from the coal, 216 million tons from the copper ore, and 135 million tons from the iron ore. These figures do not include the initial stripping required before ore production. For example, the ASARCO Mission mine started stripping operations in August 1959 and by mid-November 1961 had removed 46.3 million tons of material including 1.2 million tons of ore.* Initial excavation of this type offers the most favorable conditions for utilizing the earth-moving ability of nuclear explosives. EXPLOSIVE CASTING FOR REMOVING OVERBURDEN The use of explosives to remove overburden is not a new idea. Conventional explosives have been used for this purpose for many years with varying degrees of success. Several small coal strip operators have used this idea to increase production. At these mines about one-third or more of the overburden is thrown by explosives across the pit and onto spoil piles. The additional costs of drilling more blast holes and more explosives are more than compensated for by a reduction in the time required to uncover the coal, and by an increase in coal production.

Jan 1, 1964

By C Gunther

The classification here used is one of convenience only; it is not intended to include all known types of ore deposits. The characteristic features of the several well-marked types of primary mineralizations are described without reference to the ultimate source of their metals. The minerals of many deposits of obscure origin were probably introduced through fissures that are now healed, or are due to the migration of metals from such deposits. It is not within the scope of this book to enter into a general discussion of the genesis of ore deposits but, in view of the progress being made in our comprehension of the conditions under which ore deposits were formed, mention should be made of recent work. J. E. Spurr's two volumes, "The Ore Magmas," are recommended as crystallizing the views of those who are inclined to ascribe the origin of most ore deposits to a differential precipitation from magmatic rock masses and to the migration and precipitation of the viscous, liquid or gaseous exhalations from those masses. He has especially emphasized the role

Jan 1, 1932

By R. D. Pehlke, W. M. Small

The effect of added alloying elements on the solubility of nitrogen in a liquid alloy of 74 wt pct Fe. 18 wt pct Cr, and 8 wt pct Ni has been studied. At 1600°C and 1 atm nitrogen pressure, aluminum, chromium, columbium, manganese, molybdenum, tantalum, and vanadium increase the solubility of nitrogen in the liquid 18 Cr-8 Ni alloy, whereas additions of cobalt, copper, nickel, silicon, tin, and tungsten decrease the solubility. Interaction parameters based on a constant ratio of iron, chromium , and nickel have been used to quantitatively define the changes in nitrogen solubility. INVESTIGATIONS on the solubility of nitrogen in liquid iron have usually treated the pure metal, and often the influence of a single added element. Pehlke and Elliott1 carried out a comprehensive study on the influence of alloying elements on nitrogen solubility in liquid iron, and compared their results with previous studies. Turnock and pehlke2 have recently reported a study on the solubility of nitrogen in multicomponent liquid iron alloys. The original interaction parameter proposed by wagner3 was successfully employed in these studies. The need for obtaining information on the gas solubility in more complex alloys is indicated by the increasingly significant role played by dissolved gases in the processing of iron-based materials. The commercial stainless steels, for example, represent an area where data on nitrogen solubilities are required as a function of composition, temperature, and gas pressure. The nitrogen solubility in liquid Fe-Cr-Ni alloys has been studied by Humbert and Elliott.4 Their investigation covered the entire ternary system, and attempted to use data from binary alloys to predict nitrogen contents in liquid ternary alloys. Langenberg,5 using a method developed by Morris and buehl,6 calculated the nitrogen solubilities in multicomponent iron alloys from data available on binary iron alloys at 1600°C. Nelson,7 using a regular-solution model, extended this prediction to include the effect of temperature. Chipman and corrigan8 and Turnock and pehlke2 also employed empirical methods to calculate nitrogen solubilities in liquid multicomponent iron alloys. In order to provide a basis for predicting nitrogen solubility in liquid stainless steels, and to extend the data available for thermochemically modeling systems of this type, the following investigation was carried out. The study involved measupements of nitrogen solubility in a nondilute alloy and examination of the influence of a small addition of an alloying element on the nitrogen solubility. The study was focused on a very narrow range Of composition in the vicinity of 18 wt pct Cr-8 wt pct Ni (herein referred to as 18-8) with special emphasis on the change of.nitrogen solubility with the addition of a fourth metallic element. EXPERIMENTAL PROCEDURE A Sieverts' apparatus, described previously,1,2 was used in this investigation. The charge materials were contained in a recrystallized alumina crucible and inductively melted. Additions were dropped from a glass side-arm. All materials were hydrogen-refined and vacuum-treated to eliminate or minimize the oxygen content. The source and purity of materials is given in Table I. The initial metallic charge was heated to approximately 1000°C and held under vacuum for 30 to 45 min as a means for removing hydrogen and adsorbed gases. Argon was used as the calibrating gas to determine the "hot volume". The average hot volume of the system was approximately 50 cu cm STP and a few experimental runs were made using a reaction bulb with a hot volume of 80 cu cm. The temperature range studied was from 1550° to 1700°C and the temperature was measured optically. THEORETICAL PRINCIPLES General Discussion. Nitrogen dissolves in liquid iron alloys according to the reaction: 1/2N2(g) = N (wt pct in solution) [l] The equilibrium constant, K1, for this reaction is written as:

Jan 1, 1969

By Henry Fernald

THE accounting system or bookkeeping methods of any company are principally the concern of that company and of those who are in control of its affairs. Its published financial report is, however, primarily intended for those who are not already fully informed regarding its operations and finances. Whatever may be the advantages of standardization of accounting and bookkeeping methods, it must be admitted that a company has a certain right to handle its accounts and keep its books and records in whatever manner may seem to it best adapted to its affairs, even though such methods may differ materially from those generally adopted by others. In its financial reports it should not, however, either ask or expect that the statements it makes or the terms which it uses will be given in its case a meaning and interpretation different from that which they are ordinarily considered to have inn similar reports and statements of other companies. The particular form and arrangement of such reports is a matter concerning which there may be much difference of opinion. It is of little importance whether current assets come first or last in the Balance Sheet, but it is important that there should not be included under this designation any items which are not properly current assets within the generally accepted meaning of that term. The extent to which stockholders or others interested are to be made acquainted with the full details of a company's business is a question which the proper authorities must in each case decide. It should, however, be recognized that there are certain facts regarding a mining company which must be set forth in a financial statement if it is fully to cover the conditions and affairs of the company. For example, a financial statement which does not include or is not accompanied by a statement of the ore reserves of the company does not fully set forth its financial condition. This is true whether the absence of such a statement of ore reserves is because it is not desired to make public the figures or whether it is because the ore reserves themselves are not definitely known or accurately measured.

Jan 1, 1928

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By J. N. Maycock, P. W. M. Jacobs

Previous measurements of the thermoelectric power of ionic crystals are reviewed briefly. It is concluded that, while extensive measurerements are available on systems in which the electrode M has a cation in cornon with the sall MX, there is as yet little modern work on systems in which the metal electrode M' does not haue a calion in common with the salt. We haue now measured the thermoelectric power of- single cryslals of KC1 and of KC1 + SrCl2 between plati.nu?n electrodes over a much wider range of temperature than before. individual ionic heats of transport, which, while probably not very accurate, are of a reasonable order of magnitude, are obtained from this data on the basis of an assumption that charge carriers do not cross the electrode/salt interface. RELATIVELY little work has been done on thermal diffusion in ionic crystals. Reinhold and coworkers1-I measured the thermoelectric power and Soret effect in silver and cuprous salts and their mixed crystals. One electrode was kept at constant temperature and electromotive force was measured as a function of the temperature gradient. This is not a satisfactory technique if the results are to be compared with theory; rather should the electromotive force be measured for small temperature differences as a function of the mean temperature of the two electrodes. They used electrodes having the same cation as the salt. Patrick and Lawsons measured the thermoelectric power of AgBr and of AgBr containing 0.25 mole pct CdBr2 using silver electrodes and temperature gradients of 10°C in the temperature range 100° to 400°C. The results were analyzed using the Teltow9 values of the ratio of the mobility of the two types of charge carrier (cation vacancies and interstitials) found from conductance measurements and the wagnerlo estimate of the heterogeneous contribution to the thermopower, Ohet They obtained values of qi = 0.017 ev and q$ = -0.385 ev for the heats of transport of interstitial Ag ions and cation vacancies, respectively. Their data has been reanalyzed by Haga using the corrections to the Wagner formula for ehet given by Howard andLidiard; Haga found ev. Christy et a1.14 have measured the thermopower of AgBr containing 0.01 to 1.0 mole pct CdBr,. They analyzed their results in terms of the theory of Howard and Lidiard and found that excellent agreement with the theory was obtained if q5 + : + hF was set equal to 0.70 ev at 175°C and equal to 0.58 ev at 250°C. Since Teltow's value for hF, the enthalpy of formation of a Frenkel defect pair, is 1.27 ev, this means that qt + q: increases in magnitude from -0.57 ev at 175°C to -0.69 ev at 250°C. This result is in poor agreement with Patrick and Lawson's value of -0.37 ev for pure AgBr (for which the corrections to the Wagner estimate for ehet are very small). christy1' has also reported thermopower measurements for pure silver halides and for the systems he finds that qr + qt for AgBr increases in magnitude from about -0.55 ev at 150°C to about -1.1 ev at 400°C. The temperature dependence of the sum of the heats of transport in AgCl is very similar in magnitude. The sum qi + q cannot be decomposed into the individual interstitial and vacancy heats of transport without a knowledge of the entropy contribution from the change in the lattice vibrational frequencies around the interstitial and vacancy. Despite this it seems an inescapable conclusion from Christy's analysis that and -6 = Q Ag are quite strongly temperature-de pendent and that -q: is much greater in magnitude than the corresponding activation energy for vacancy migration, +0.37 ev. It remains a mystery as to why the data for pure AgBr are fitted so well by the assumption of temperature-independent heats of transport if association of impurity ions and vacancies is neglected.l The values for q$ and q: so obtained are also much more in line with those expected from a simple kinetic interpretation of the heats of transport due to wirtz.17 Christy and Hsueh have also measured the thermopower of CuCl between copper electrodes; 0 for pure CuCl is comparable with that for the silver halides but, owing to the limited solubility of divalent cation impurities it was not found possible to deduce values for the heats of transport. In contrast to these extensive measurements on cells of the type M MX 1 M, there have been relatively few attempts to measure the thermoelectric power of cells of the form M' 1 MX I M'. (We specifically exclude from discussion cells of this type in which the metal electrodes M' are in contact with gas containing a controlled partial pressure of either M or X,, since in these cells the electrochemical reactions are analogous to those of the first type.) The thermoelectric power of Pb12, PbC12, TlC1, TlBr, TlI, NaNO3, and KNO 3 between platinum electrodes was measured by Thie1e.l3 In discussing these measurements Holtan20 asserts that the thermopotential initially fluctuated wildly and even changed sign before approaching a steady value. A high degree of irreproducibility is also evident in the work of Nikitinskaya and Murin21 who first studied the thermopower of NaCl and KC1 between platinum electrodes. Much better reproduci-bility was achieved in our earlier measurements on KC1;22 these were, however, confined to a relatively narrow temperature range and one of the objects of the work reported in this paper was to extend the temperature range of the measurements of the thermoelectric power 8 of KC1. The only other published

Jan 1, 1967

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Walter Renton Ingalls

Metallurgical literature has no record of any ore beneficiated for cadmium alone, and the cadmium of commerce is derived from zinc ore, with which cadmium is generally associated. Zinc ores free from cadmium—e.g., the ores of the Franklin and Stirling mines, New Jersey, and of Broken Hill in Rhodesia—are rare. Blende concentrates of 50 to 60 per cent grade have contained (in production of important tonnage) as much as I per cent Cd, which is unusually high. The concentrates from the Tri-State district average from 0.3 to 0.4 per cent Cd, which is high. The concentrates from mines west of the Rocky Mountains seldom are higher than 0.2 per cent. In the periodic system of the elements, cadmium is in the same group with zinc. Its properties and compounds are similar. Its metallurgy is also similar. Cadmium has a melting point of 320°C. and a boiling point of 778"C., while the melting point of zinc is 415'C. and the boiling point gos°C. These conditions, together with the lower reduction temperature of cadmium oxide, indicate means for. separating cadmium from zinc. Cadmium in spelter is viewed, if not as an impurity, at least as an alloying element that may be objectionable, its special effect being hardening. However, for some purposes, a little cadmium in spelter is desired, and 0.4 per cent may be permissible, even in spelter for rolling. Cadmium in spelter for brassmaking is completely volatilized at the temperature of that process, and in bygone days an immense quantity of cadmium must have been lost in the fumes from these furnaces. Pyrometalltjrgy—Early Cadmium compounds, sulphide and oxide, being more volatile than the corresponding compounds of zinc, loss of cadmium begins to occur from the first furnace operation. In normal roasting, even with Tri-State ore, this loss may not be very high. Raw ore, assaying 0.4 per cent Cd, may be expected to give a roasted product of the same assay, which would imply a cadmium loss of about 15 per cent. Roasted ore, assaying 0.4 per cent Cd when distilled at ordinary furnace temperature, yielded spelter containing about half of that in the ore charged. The first draw of spelter under these conditions may assay 0.8 per cent Cd (accounting for 22 per cent of the cadmium recovery) and after the several draws of spelter have been equalized the cadmium content may average 0.35 per cent. If, therefore, 2000 lb. of blende averaging 0.35 to 0.4 per cent Cd is roasted and distilled, there may be obtained 1000 lb. of spelter, assaying 0.35 per cent Cd or 3.5 lb. content, which entering into Prime Western spelter will be sold at the spelter price. It will be observed from the outline hereinbefore (summarizing conditions prior to the introduction of sintering) that the main loss of cadmium occurred in the distillation process and by failure to condense, which could be ameliorated by attaching a prolong to the condenser, thus collecting

Jan 1, 1944

By Albert F. Hill

The manufacture of structural shapes in steel of uniform quality, which shall command the full confidence of the engineer, is a problem in practical metallurgy which is beginning to attract much attention in this country. The progress of the past fern years in the improvement of plant and processes has placed it within the power of the steel-maker to supply a material of such chemical composition as will meet the requirements; but this solves only in part the difficulties of the constractor. It is well understood that the influence of shop manipulations is a most decisive one upon the mechanical properties of the finished product; in many cases so great, in fact, as to cause an entire transformation in the character of the material, and to render it unfit for the service for which it was intended. On the other hand, mechanical treatment is frequently resorted to as an efficient corrective of certain undesirable properties, which may be due either to chemical composition or previous manipulation. This understood and accepted, it is evident that careful investigation of the effects of mechanical treatment is fully as necessary to the successful use of steel in engineering structures, as the investigation of the influence exerted by its chemical composition. All structural material has to undergo more or less mechanical treatment, such as shearing, punching, upsetting, etc. Each of these operations produces effects which are far more marked and decisive in steel than they are in iron, and means must therefore be adopted to counteract, or at least to modify, these effects before the material is permitted to enter the structure. The fact that both shearing and punching affect the tenacity and elasticity of steel has long been recognized; bat, through more recent investigations, it has been established that these effects are purely local, and are therefore susceptible of correction by other and simpler means than annealing. The importance of this discovery to the use of steel in structures is very great. The impracticability of

Jan 1, 1883

By F. N. Rhines, A. H. Grobe

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By A. H. Grobe, F. N. Rhines

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By R. F. Hollis, C. K. McArthur

PRIOR to the application of anion exchange, all recovery of uranium from acid leach liquors precipitated an impure product requiring further upgrading before it could be refined. The ion exchange process, on the other hand, provides excellent selectivity for extracting soluble uranium from leach liquors, so that high grade concentrates can be produced directly. The discovery that uranium is readily adsorbed by anion exchange resins, together with the experience of resin and equipment manufacturers in water treatment, led to rapid development of ion exchange in a multiple column operation. Many processing plants using fixed bed ion exchange are in operation or under construction in Africa, Australia, and Canada. There are a limited number in the U. S. Although the fixed bed process has been highly successful, the feed to the ion exchange columns must be a clear solution, which is obtained by filtration or by countercurrent decantation of leached pulps. With some ores, poor filtration or settling characteristics make production of a clear solution difficult. Most processing plants in the U. S. receive their ores from a number of small mines, and there is considerable variation in the settling and filtering behavior of the ores. An ion exchange process was therefore desirable in which the uranium could be recovered directly for the leached pulp by adding ion exchange resin, which could be then separated from the pulp by a screening operation. The process would thus resemble the cyanide-charcoal process in which gold is adsorbed from cyanide pulp by means of activated charcoal. Preliminary tests in which leached pulps were directly contacted with resin beads led to the development of the RIP process.

Jan 4, 1957

By John T. Dickman, Ralph E. O’Dette

Chemical Abstracts Service (CAS) is in the process of evolving a computer-based information system which will process all of the material selected for abstracting in the area of chemistry and chemical engineering and its related fields such as the earth sciences and technologies. This system is already operational to some extent and is expected to be fully utilized by 1971. The objective of CAS is to make chemical and related information more readily available, more usable and more used. Chemical Abstracts handle some 5000 abstracts weekly from 13, 000 journals and patents from 25 nations. These cover all of the 80 CA subject sections which relate to chemistry and also extend into areas of interest to geologists, mineralogists, and mining engineers. In this way, CAS fulfills its objective of complete coverage of its major fields, informative abstracting, and indexing to maximum specificity. The concept of a computer-based information system is that of a single machine-language data base into which the results of intellectual analysis of the literature are entered and from which computer programs produce a variety of publications and services applicable to the needs of a wide range of users.

Jan 1, 1969

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. 0. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico."2 The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter.

Jan 1, 1927

By G. W. Healy, W. D. Forgeng, N. R. Griffing

The liquidus surface of the C-Cr-Fe system to 1900°C has been mapped from carbon solubility and freezing point measurements, metallographic observations, and published data. In the graphite field, the surface drops precipitously to meet a slope descending from the Cr3C2-C join through the mixed carbide fields to a meandering eutectic valley; this flows from the Cr-C to the Fe-C edge. On the low-cavbon side of the valley, the surface rises to the chromium corner. 1 HE purpose of this inquiry was to gain a more complete knowledge of the C-Cr-Fe liquidus surface. This required an extensive study of carbon and chromium-rich alloys which, in the past, have received the least attention. Sanbongi el al.1 measured the solubility of carbon in liquid alloys containing up to 25 wt pct Cr at temperatures of 1460" and 1545°C and found that it increased with chromium content and temperature. Lucas and wentrup2 also made solubility experiments in graphite crucibles, but at higher chromium contents in the range of 38 to 80 pct and at temperatures of 1550" to 1700°C; however, their experiments were relatively few, and the effect of temperature was not consistent. The present investigation included compsitions ranging from 0 to 94 pct Cr and 1.4 to 11.7 pct C at temperatures up to 1800°C. Saturation experiments in graphite crucibles, thermal analyses during freezing, and metallographic and X-ray diffraction studies were employed to obtain desired information which, together with published data from other investigations about the binary edges and the ternary system at lower carbon levels, made possible the construction of a comprehensive C-Cr-Fe liquidus surface. C-CR-FE LIQUIDUS SURFACE The derived ternary liquidus surface is shown in Fig. 1 where the solid curves are liquidus isotherms. The dashed curves and the binary edges are the liquidus field boundaries of the primary crystals, the arrows along these boundaries indicating their direction with decreasing temperature. Each intersection of three internal boundaries is the composition of liquid involved in four-phase isothermal equilibrium with the three primary crystals whose liquidus fields touch there. It may be observed that a total of six four-phase equilibria occur at melt temperatures. The general topography of the liquidus surface consists of a eutectic valley sloping down from the Cr-C edge at 3.2 pct C to the Fe-C edge at 4.25 pct C. The liquidus surface rises in two directions from the valley, one hillside terminating at the Cr-Fe edge while the opposing hillside rises toward the carbon corner out beyond the top edge of Fig. 1. Both hillsides are interrupted by intersections of surfaces or joints representing the liquid colmpositions of various three-phase equilibria. Seven primary crystals occur, namely a(bcc), ?(fcc), graphite, (Fe, Cr)3C capable of dissolving as much as 15 pct Cr, and three different chromium carbides in which iron is partially soluble by substitution for chromium. The composition ranges of the primary l~hases at melt temperatures are shown

Jan 1, 1962

By Clifford Wilson

SCREENED pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments a. Consolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use. of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1932

By Dr. O’Neil Thomas J., Donald W. Gentry

Pure gold was hidden in the quartz, they said, 'Twas proved by dreams and signs, and rods divining, By chemic tests, and spirits of the dead, In fact by everything-except by mining. " from R.E. White, "The Mining Town," Alta California, August 18,1873 Textbooks in mining engineering have traditionally covered ore reserve estimation and mine valuation in a single volume. Indeed, Examination and Valuation of Mineral Property by R. D. Parks (1957), having been the standard of the profession for over 20 years, is a classic example. However, the state of knowledge in these two fields has grown tremendously. Most mining engineering curricula now cover these topics in separate courses, and in practice, these tasks are usually performed by different individuals. Thus, this trend now suggests the need for separate, specialized publications rather than a single volume for both topics. Because of the separate development of the science of ore reserve estimation, it is important to state at the beginning what this chapter does not cover. It does not address in detail the design of sampling programs, sampling methods, or the processing of samples or sample data compilation. There are a number of suitable references available on these topics, including Peters (1978), Gy (1979), as well as the previously cited book by Parks. Furthermore, this chapter does not cover in any substantial detail either the traditional methods for using sample data to calculate ore reserves or the more recently developed geostatistical methods. The traditional methods are thoroughly covered by Popoff (1966) and more concisely by Barnes (1980). Among the more useful references for statistical applications in ore reserve estimation are Barnes (1980), David (1977), and Clark (1979). A thoughtful review of the entire science and art of ore reserve estimation is provided by King, McMahon, and Bujtor (1982). In spite of the fact that expansion of knowledge now calls for separate books on ore reserve estimation and financial evaluation, neither publication can ignore the important interrelationships between the two fields. In regard to this text, the unique and crucial role of ore reserves can not be omitted entirely; however, the field is now simply too extensive to treat here in any comprehensive manner.

Jan 1, 1984

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951