Search Documents

By J. D. Runkie, A. G. Lyle, G. A. Gillies

Tar evaluation of data obtained by selective flotation from even a simple ore is a very difficult process, and when the ore tested is complex the process becomes extremely difficult and cumbersome The authors, in the course of an investigation into the selective behavior of various flotation reagents on nonmetallic minerals§ were confronted with an aggravated form of this difficulty, owing to the large mass of data that had accumulated over a period of years They finally devised a method whereby the results of the various flotation tests could be correlated and interpreted by means of graphs representing recoveries and rejections of the component minerals in the ore This method of graphical analysis proved so useful in nonmetallic flotation that it was afterwards applied to sulphide flotation, where it yielded equally satisfactory results Since this method of analysis leads to very definite conclusions as to the effect of changes in reagents and flotation procedure, it is felt that a wider application of the method might assist the industry by reducing the amount of test work required, and possibly increase the accuracy of the final analysis GRAPHS In Fig I, four curves are plotted on the same graph with cumulative percentages as ordinates and cumulative weights as abscissas In this instance the four curves are named, respectively the barite-recovery curve, the limestone-rejection curve, the silica-rejection curve, and the summation curve In these tests barite was the mineral concentrated, therefore a barite concentrate was produced Definitions Before explaining the curves in detail it might be advisable to define several new terms, such as "percentage rejection," "summation index," and "summation curve," as well as the word "test," which has been used in a special sense. A "test" will include all the operations performed upon a batch of ore from the time it is placed in the rod mill until the last product has been assayed Thus a test may be a comparatively simple procedure producing only one concentrate and a tailing, or it may be a very complicated procedure producing five or more concentrates of a specific mineral as well as a tailing The number of concentrates produced will depend entirely upon whether the collector was added to the pulp in the flotation cell in one lot or was added in five or more portions Percentage Rejection-The ability of a selective flotation collector to reject an undesired mineral is just as important as its ability to collect the desired mineral The percentage rejection curves shown on the graphs give this factor due consideration and its value is calculated as follows Suppose a concentrate contains 5 per cent of an undesired mineral This indicates

Jan 1, 1942

By W. H. Yarroll

This paper presents a general discussion of the utility of the statistical technique known as multiple correlation, and gives three specific examples of its application. The first demonstrates the most simple form, or straight-line, multiple correlation. The other two demonstrate multiple correlation analysis in best-fitting third-degree parabolas. With the increasing availability of digital computers, the method becomes entirely feasible where heretofore its use was impractical. The advantages of the method are discussed, and curves are presented which were developed by computerizing the regression equations developed in the examples. The method described in this paper is for use with complex systems, and the examples given are complex metallurgical systems. This subject falls under the general classification of cybernetics, which is defined' as "the science of control and communication, in the animal and the machine." Machine, in this case, can include chemical and physical processes which take place within machines and processing equipment of all kinds. The classical approach to scientific investigation has been the construction of simple models and the changing of variables one at a time. This method is wholly inadequate for obtaining useful information from the complex systems of modern technology including many of our flotation and hydrometallurgical processes. Cybernetics offers the method by which complex systems which have been implemented as an art in the past can now be analyzed with all the discipline of a science. Mathematical techniques for achieving multiple correlation analysis have decided advantages over some of the other statistical methods.2-4 Multiple correlation does not require a series of experiments that have been rigidly planned as do many of the other statistical methods. For this reason, it can be used effectively for interpretation of information from op- erating plants, where planned experiments are impractical, as well as for laboratory experiments. First-degree multiple correlation has been used for many years, and was useful, but limited to linear or nearly linear relationships. The technique described in this paper provides a method for analyzing systems which may be non-linear. This particular technique is multiple correlation analysis in best-fitting third-degree parabolas. It is quite possible that lack of reference to the technique has been due to the overwhelming mass of computations it requires even for relatively simple problems. With the advent of computers, however, its use has become entirely feasible. For the benefit of those who may not be familiar with the subject, it might be well to pause at this point to discuss multiple correlation analysis — what it is and what it achieves. To go back to the old familiar fitting of a set of points with a best-fitting straight line by the least squares procedure, it is conceded that this a good method where there is only one independent variable influencing the dependent variable under consideration, and providing that the relationship is linear. In most fields of investigation, however, there are usually a number of factors exerting important influence, and they frequently bear relationships with the dependent variable other than straight line. Under these conditions, it is easy to see how misleading a simple correlation study might be. Multiple correlation can be used for any number of variables. Within the experience of the writer, this technique has been used to establish regression equations for determination of carbon rate, burden permeability, and production rate on iron blast furnaces, production rate on open hearth steel furnaces, life of molds for steel ingots, rolled steel tensile strength and various defects in rolled products, the performance of ore dressing equipment, and optimization of extractive metallurgical process variables. The discovery of mathematical correlation does not prove, per se, true cause-and-effect relationship, but simply establishes a hypothesis. If the regression equation can be used to make successful predictions of what will happen with future arrays of independent variables, then one can feel reasonably assured that true cause-and-effect relationships have been discovered.

Jan 1, 1968

By N. A. Gokcen

THE data of Chaudron,1 Tonosaki,2 and Collins³ on the thermodynamic properties of MOO, disagree widely. These authors, by using essentially similar methods, studied the following reaction: 1/2MoO2(s) + H2(g) == i/2Mo(s) + Ph,o H2O(g),K = —----- [1] Ph2 Tonosaki used a vacuum system consisting of a furnace containing MOO, and a water saturator whose temperature was kept at 25 °C with a thermostat. After repeated evacuation, hydrogen was admitted slowly into the system. The experiments were based upon the fact that at a constant furnace temperature and constant partial pressure of water, the total pressure of gas mixture over MOO? + Mo is constant. Any attempt to vary the pressure by external forces would vary only the amounts of MoO2, and Mo, after which the pressure should return to the equilibrium value in accordance with the equilibrium constant of reaction 1. The actual value of K was determined from the total equilibrium pressure (sum of Ph2o + Ph2) at each temperature. The total pressure of gas was varied within the range of 80.2 to 125.4 mm Hg, within a temperature range of 645" to 823 °C. The results were summarized as log K = 0.9413 — 1444.6/T for reaction 1. The ratio of H2O/H2 was considered to be uniform in spite of the presence of a thermal gradient across the static gas phase. It was shown by Rosenqvist and Cox,' however, that in somewhat similar circumstances the error resulting from thermal diffusion may be large. Collins³ improved Tonosaki's method by attempting to avoid thermal diffusion errors. His equilibrium data were obtained at 700°, 800°, and 900° C, and the result for reaction 1 was expressed as log K = 1.258 — 1822/T. The purpose of this investigation was to study reaction 1, avoiding the thermal diffusion errors, and to obtain equilibrium data in a considerably wide temperature range for the reliable extrapolation of the resulting thermodynamic functions. Experimental Procedure The diagram of the apparatus is shown in Fig. 1. Tank hydrogen was passed through a tube containing platinized asbestos at 425 °C in order to convert a trace of oxygen into water vapor. The flow rate was carefully controlled with a capillary-type flow-meter B and a bubbling column D. The gas was then presaturated sufficiently at P and led into a condenser system immersed in a thermostat, controlled to within ±0.002C. The temperature of the thermostat was measured with a thermometer calibrated against a certified standard. The temperature of P was adjusted to avoid the condensation of unduly large amounts of water as judged from the rate of flow out of the capillary tube M. Argon was purified by passing it through magnesium chips kept at 630°C. After passing through the flowmeter B', it was mixed with moist hydrogen emerging from the thermostat. The resulting gas mixture was then led into the hot zone of the furnace through the heated glass tubing and the silica tube S, thus insuring the same ratio of PII2o/Ph2 from the condenser to the reaction chamber, thus avoiding thermal diffusion. The entire gas system was of all-glass construction, except at the magnesium train. The furnace comprised a glazed alumina tube over which a 15-in. platinum coil was wound. The lower end of the alumina tube was tightly closed with a brass bottom and a silicone rubber gasket, and the upper end with two glass disks, each with a hole of 1/16 in. in diameter, through which the gas mixture escaped into the atmosphere. A back-up coil of kanthal wire facilitated the temperature control of the furnace. A coil of annealed molybdenum strip of 99.99 pct purity, 0.005 in. thick and 0.050 in. wide, and weighing 17 g was hung in the furnace with a 0.010-in. platinum wire attached to one end of a sensitive analytical balance. The temperature of the furnace was measured with a Pt-Pt-10 pct Rh thermocouple checked against a standard. The experimental procedure consisted of heating the gas purification trains, adjusting the gas flow rates, attaining a constant thermostatic temperature, flushing the entire system for 2 hr while heating the furnace to well above the expected equilibrium temperature and then cooling it at a rate of 0.3°C per min during which time the change in the weight of molybdenum was observed on the balance. For a given thermostatic temperature, i.e., a constant Prr,o/Px,, molybdenum oxidized upon cooling slightly below the equilibrium temperature. The procedure was then repeated by heating the furnace and thus reaching a temperature slightly above the equilibrium value. The average of the two temperatures, differing by 2" to 3"C, was considered to be the true equilibrium temperature. In order to determine the stoichiometric composition of the oxide phase present in this investigation,

Jan 1, 1954

By B. D. Saklatwalla

FOR the proper understanding of the inclusion of certain elements in this review it seems necessary to state the meaning of "rare metals." Certain elements occur in deposits limited in extent or concentration, so that the extraction of the element in relation to market conditions becomes uneconomical. Others may occur in extensive and rich deposits but the reduction of the metal may be difficult and costly. Both these conditions effect the same result, namely, make the metal rare and costly. As an example of the first kind may be mentioned radium and of the second, calcium.

Jan 1, 1939

By George Sachs, S. M. Clark, George Espey

he tendency of a commercially drawn cartridge case to crack in the mercury test and the relation of cracking tendency to residual stress retained after drawing were studied. The fourth drawpiece (next to the final) of caliber 0.30 cartridge cases produced by Frankford Arsenal were selected as test pieces. These exhibited an exceptionally high cracking tendency, making a detailed study possible. To obtain fast cracking in the mercury test, about 0.0015 to 0.003 in. must be removed from the wall thickness of the drawpiece by pickling, and it must be subjected to the mercury test immediately after washing. Removal of the adhering mercury by annealing and subsequent squeezing of the case in a vise was used to reveal definitely the presence or absence of cracks. Various lots of apparently identically fabricated cases were shown to possess a different cracking tendency. Machining off or boring a hole in the base gradually reduced and eventually eliminated the cracking tendency. On the contrary, shortening of the wall (body) reduced the cracking tendency only if the wall became so short that the cracking zone was directly affected. By boring out the base and pickling from the outside and then splitting the resulting rings, it was possible to determine the approximate stress distribution in the base and in the adjacent part of the wall. Small compression stresses were present in the core and the major part of the base, while the surface of the base and the adjacent wall contained high circumferential tensile stresses. On the contrary, the wall when parted from the base contained only insignificant residual stress. The conception is advanced, that the stress distribution in a drawn cartridge case corresponds fundamentally to that of a tube (wall) shrunk on a disk (base). Such a stress distribution results from the tendency of the base to recover elastically by an increase in diameter from the biaxial compression during drawing while the wall exhibits little tendency to change its diameter after progressing through the die. This is confirmed by measurements which show the base diameter to be slightly larger than the wall diameter.

Jan 1, 1945

By William Campbell

(Cleveland Meeting, October, 1912.) THE structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, it series of transition-products with distinctive structures, to which have ,been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school ; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-products-all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron-carbon diagram and the structures met with in hard- * Associate Professor of Metallurgy, Columbia University in the City of New York.

Dec 1, 1912

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the, St. Eugene Concentrator, Moyie, B. C., and (3) the. Tadanac (Customs) Concentrator,Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a FIG. 1.-THE SULLIVAN CONCENTRATOR, CHAPMAN CAMP, B. C. (NEAR KIMBERLEY, B. C.). low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential-flotation.

Jan 1, 1927

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By H. W. Morse

THE CHAIRMAN (H. W. MORSE).-Gentlemen, for the first time in the history of the American Institute of Mining Engineers, we have a full session on the subject of leaching-especially on the leaching of copper ores.. This branch of metallurgy is rather in its infancy. We have had one big plant running for a year or more, and pretty successfully; and another one which will be started in February or March, the New Cornelia. We have another one at Garfield for the Utah company, which is just designed and construction begun; and from several other points come reports of interesting test work. The first paper on the program this evening is one of some of the test work on the New Cornelia ore by myself and Mr. H. A. Tobelmann. LAWRENCE ADDICKS, New York, N. Y. (written discussion).-The Ajo proposition has had, as I understand it, two great advantages: it has not been obliged to measure leaching against flotation or some other metallurgical process, and it deals with a copper content high enough

Jan 12, 1916

By Carl Samans

THE attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewski1 were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials hag been supple-mented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantita-tive data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures.

Jan 1, 1934

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By R. W. Snyder, W. H. Guilinger, B. S. Gottfried

Two numerical methods are presented JOT solving the equations Jor one-dimensional, multiphase /low in porous media. The case oF variable physical properties is included in the Formulation, although gravity and capillarity are ignored. Both methods are analyzed mathematically, resulting in upper and lower bounds for the ratio of time step to mesh spacing. The methods are applied to two- and three-phase waterflooding problems in laboratory-size cores, and resulting saturation and pressure distributions and production histories are presented graphically. Results oJ the tuo-phase flow problem are in agreement with the predictions of the Buckley-Leuerett theory. Several three-phase flow problems are presented which consider variations in the water injection rate and changes in the initial oil-and ujater-saturation distributions. The results are different physically from the two- phase case; however, it is shown that the Buckley-Lez~erett theory can accurately predict fluid interlace velocities and displacing-fluid frontal snturations for three-phase flow, providing the correct assumptions are made. The above solutions are used as a basis JOT et~aluuting the numerical methods with respect to machine time requirements and allowable time step for a fixed mesh spacing. INTRODUCTION Considerable progress has been made in recent years in obtaining numerical solutions of the equations for two-phase flow in porous media. Douglas, Blair and Wagner2and McEwenll present different methods for solving the one-dimensional case for incompressible fluids with capillarity (the former using finite differences, the latter with an approach based upon characteristics). Fayers and Sheldon4 and Hovanesian and Fayers8 have extended these studies to include the effects of gravity. West, Garvin and Sheldon, l4 in a pioneer paper, treat linear and radial systems with both capillarity and gravity and they also include the effects of compressibility. Douglas, Peaceman and Rachford3 consider two-dimensional, two-phase, in compressible flow with gravity and capillarity and Blair and Peaceman1 have extended this method to allow for compressible fluids. No one, however, has examined the case of three-phase flow, even for the relatively simple case of one-dimensional flow of incompressible fluids in the absence of gravity and capillarity. In obtaining a numerical technique for simulating forward in situ combustion laboratory experiments, Gottfried5 has developed a method for solving the one-dimensional, compressible flow equations with any number of flowing phases. Gravity and capillarity are not included in the formulation. The method has been used successfully, however, for two- and three-phase problems in a variable-temperature field with sources and sinks. This paper examines the algorithm of Gottfried more critically. Two numerical methods are presented for solving the one-dimensional, multi-phase flow equations with variable physical properties. Both methods are analyzed mathematically, and are used to simulate two- and three-phase waterflooding problems. The numerical solutions are then taken as a basis for comparing the utility of the methods.

Jan 1, 1967

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-

By Donald W. Gentry

The recently established SME-AIME Education Board has completed its first full year of operation, and its six constituent committees-Accreditation, Career Guidance, Continuing Education, Educational Statistics, and Scholarship-have been extremely active in identifying and initiating programs to serve the educational needs of the Society of Mining Engineers and its members. The Continuing Education Committee-primarily concerned with the needs and problems associated with providing a continuing education program for SME members-is responsible for: (1) determining the need for short course offerings; (2) developing needed courses, along with new means and opportunities of presentation; and (3) scheduling and evaluating course presentation. In response to this charge, the committee has sponsored two short courses at the SME-AIME Fall Meeting in St. Louis and three short courses at the AIME Annual Meeting in Denver. Its major effort, however, has been directed toward the 1978 SME-AIME Fall Meeting to be held in Orlando, Fla., where 18 days of short-course instruction have been scheduled. A portion of these courses will be presented prior to the meeting, with the remainder to be presented in Nassau, Bahamas, immediately following the meeting.

Jan 7, 1978

By Frank Haas

THE public generally has-become aware that there is something wrong with the coal industry and a clamor has arisen for an explanation if not a remedy for this disorder. It is only reasonable that this Institute be looked to for a diagnosis to show the way for some other .agency to prepare the patient for prescription or operation. The subject is extensive, widely diversified, and beyond the efforts of an individual to cover completely; one of the objects of this paper is the initiating of a symposium on the non- technical factors essential to an understanding of the bituminous coal industry. The present condition of the coal industry cannot be described in a few words but, in effect, it resolves itself into a simple statement: The average coal operator is losing money notwithstanding a firm conviction on the part of the consumer that he pays too much for his coal. Without enumerating the many and varied. factors which contribute to this condition, this paper will be devoted to the interrelation of taxation and ownership of coal and its effect on finance

Jan 1, 1930

By Henry Lloyd Smyth

In 1891-92 1 was entrusted with the geological survey of part of the large area lying between the Marquette and Menominee iron-ranges in the Upper Peninsula of Michigan, and extending from the Republic trough on the north, through portions of the valleys of the Michigamme and Fence rivers, to and including the intermediate Felch mountain range on the south. Until a few years back the larger part of this area has been very difficult of access, and much of it is difficult still. The rock-surface is for the most part covered with swamp, forest and glacial deposits of various kinds, and therefore has not invited geological study. For these reasons the district, as a whole, with the exception of the Felch mountain range, remained almost unknown from a geological standpoint until our work in 1892. Our main object was to map the pre-Cambrian rocks, particularly the iron-bearing formations of Algonkian or Huronian age, and to obtain as much information as possible with reference to their sequence and structure, In carrying out this purpose, the use of simple magnetic instruments was found to be of the greatest assistance, and indeed indispensable. In this paper the results of our experience in tracing magnetic rocks by means of the disturbances produced in these instruments, have been brought together in systematic form, with such references to the particular area as are necessary in order to illustrate general principles, with the hope that they will prove useful to other workers in the same region, or in other regions where similar conditions may be encountered. The writer was efficiently aided in the field-work by Messrs. Samuel Sanford and Charlea N. Fairchild for nearly the whole period, and E. B. Mathews and H. F. Phillips for part of it,

Jan 1, 1897

By R. T. Walker

GROUND waters-hot or cold-containing small amounts of the more common earth acids, such as carbonic acid, silicic acid, hydrogen sulfide, sulfurous acid and sulfuric acid, have only a very limited "solvent effect on dominantly siliceous rocks, whether of igneous or sedimentary origin, but in limestone they often form extensive cavities; and such "limestone caves" are the only openings of considerable size and continuity in rock formations that do not owe their existence directly and almost wholly to dynamic action. Limestone caves such as are developing at the present time must have been formed in all past geological ages in which limestone beds existed and where suitable conditions for the development of such caves prevailed; hence it would seem a reasonable expectation that, in the course of geological history, a certain number of ancient limestone caves must have been utilized as channels for the passage of mineralizing solutions, during portions of their course, at least, and that, in consequence, orebodies must have been deposited in such caves. Such a conception is not novel; it was proposed many years ago, but its possibilities, as explaining certain types of ore deposits, have been rather lost sight of in the development of the theory of the metasomatic replacement of rocks by minerals. It is the purpose of this article to assemble evidence to show that many of the orebodies found in limestone beds have been deposited in pre-existing caves; to discuss the criteria whereby such orebodies can be distinguished from others which have been formed along fissures and fracture zones traversing limestone, by the more common method of metasomatic replacement, analogous to orebodies in other formations; and to describe certain orebodies-particularly the "ore channels" of the Tintic district, Utah-as illustrative of the principles discussed. Limestone caves may be divided into two classes: those formed by cold, descending surface waters, which emerge again at some lower elevation as cold springs; and those formed by hot, ascending waters of deep origin or circulation, which attain the surface as thermal springs. Although these two classes are similar in many respects, there are certain characteristic and inherent differences whereby they can usually be distinguished.

Jan 1, 1928

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By G. L. Oldright

NEARLY all of the present schemes for treating complex (i. e. lead¬silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient too compensate for the additional expense involved in beneficiating these ores. The smelters have had to meet the same general economic situation, so they can only give

Jan 3, 1924