Search Documents

By C. R. Simcoe, T. J. Koppenaal

The effect of direct and alternating currents on the quench aging behavior in an Al-4 pct Cu alloy has been investigated by use of resistivity measurements. The reaction rate increases with direct current density in the investigated range of 1000 to 3000 amps per sq cm. Alternating current of a specific frequency is observed to decrease the reaction rate by a factor of about two. ErDMANN-JESNITZER et al.,1,2 investigated the effect of direct and alternating current on the quench and strain aging behavior of low-carbon iron. In both cases they observed that direct current accelerates the aging reaction and that an alternating current can completely inhibit the aging process. The purpose of the present research was to investigate these phenomena in the quench aging behavior of an Al-4 pct Cu alloy and to determine the correlation, if any, between the increase in the observed reaction rate and possible heating effects accompanying the aging with direct current. EXPERIMENTAL PROCEDURE The aluminum-base alloy used in this investigation contained 3.98 wt pct Cu (1.72 at. pct) with impurities of 0.003 pct Si, 0.002 pct Fe, and 0.001 pct Mg. The alloy was rolled into a ribbon about 0.36 mm thick and 3.7 mm wide. The ribbon was split end from end with the ends being used as electrical contacts and the central unsplit section, about 5.3 cm in length, serving as the specimen. Solution treatment was accomplished by quenching from a salt bath at 520° ± 2°C into water at 25° ±0.5°C; the specimen was immediately transferred to a liquid nitrogen bath. All aging was done at 75° ± 0.2°C in a rapidly stirred ethylene glycol bath. Resistivity measurements were made by the double potentio-metric method employing a standard resistor; for purposes of convenience, the resistance measurements were made at 77°K. The transfer of the specimen from the aging bath to a liquid nitrogen dewar was accomplished in less than 1 sec. The aging kinteics were studied with the specimen being aged under the influence of direct current, alternating current, and without any type of current. The amount of heating caused by direct currents was investigated by soldering a thermocouple on the specimen surface and measuring the temperature change after applying various current densities. The temperature was observed to increase (from 75°C, the aging temperature) about 0.8°, 3.0°, and 8.5°C with direct currents of 1000, 2000, and 3000 amp per sq cm, respectively. When employing alternating current, the circuit was monitored with an oscilloscope and adjustments made to produce a normal sine-wave pattern. RESULTS Prior investigations3'4 in the aging characteristics of A1-4 wt pct Cu have shown that the resistivity initially increases, reaches a maximum, and then decreases to values significantly lower than the as-quenched resistivity. This type of behavior is seen in Fig. 1 which shows the resistivity at 77°K as a function of aging time at 75°C observed in this investigation. At this aging temperature, the resistivity maximum is seen to occur in about 1 to 1-1/2 min and it further decreases to the as-quenched value in about 24 min. The behavior observed with the application of direct currents of 1000, 2000, and 3000 amp per sq cm during aging is shown in Fig. 2. With increasing current densities, (+) ?pmax decreases and the rate of the aging process increases. The time necessary to reach the as-quenched resistivity value decreases from 24 min for aging without current to about 16, 10, and 7 min for aging with 1000, 2000, and 3000 amp per sq cm direct current, respectively. Fig. 3 shows the results obtained when two changes were made during the aging with 2000 amp per sq cm

Jan 1, 1963

By Elton A. Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11. mile bus ride up Railroad Creek to Holden. A11 freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting. Ore is broken by long-hole blasting using the Noranda system which has been modified to meet local conditions. Until recently, blastholes have been drilled by diamond drills. Now a partial substitution of percussion drill holes, drilled with tungsten carbide insert bits, is being made. Geology The ore body occurs as a replacement deposit in a highly metamorphosed series of sedimentary rocks, mainly gneiss and schists, in a shear zone several hundred feet in width and of undetermined length. Commercial ore has been found in mineable widths of 25 to 100 ft for approximately 2500 ft along its strike. The commercial minerals are chalcopyrite, sphalerite, and gold. During the period of mineralization considerable silicifica-tion took place giving the ore an abrasive drilling characteristic. Following the period of mineralization, numerous dikes were introduced into the ore body. The earlier ones were of granite composition having a width of a few inches up to 80 ft. These were followed by much younger, fine grained basic dikes which usually do not exceed 2 ft in width. Development of Percussion Blasthole Drilling Equipment Test work with the 1½-in. tungsten carbide bit was carried on in development headings for several months early in 1947. The short life of the bits, because of gauge loss caused by the abrasive nature of the rock, prevented its adoption for this use. However fast drilling speed and ability to drill a long uniform hole suggested its use for drilling blastholes in competition with diamond drills as diamond costs were steadily increasing and exper-ienced drillers were difficult to obtain. The 1½-in. bit was the largest available at the time initial test work was started with sectional steel. The 1½-in. hole limited the diameter of the steel thread and coupling which could be used. Type F couplings were first used but because of the small thread section excessive breakage of the steel was experienced. Type H couplings were tried next. In order to use this coupling which is 15/8 in. in outside diameter, it was reduced to 1 3/8 in. giving 1/8 in. clearance between the coupling and the hole. Rod breakage at the thread was substantially reduced but some coupling breakage was experienced, however the overall performance was considered satisfactory (see Fig 1 for illustration of coupling and thread). Early test work with the 1½ in. bit indicated machines of piston diameters larger than 255 in. would cause inserts to loosen or break. It was found however that the additional weight of the sectional steel cushioned the blow enough to prevent bit failures when 3-in. Leyners were used. Rods used with the 1½-in. bits were 7/8 in. q. o. for sectional steel and 1 in. q. o. for all chuck pieces. In May 1948, 2-in. tungsten carbide bits became available and test work was immediately started. The 2-in. hole approximated the AX (1 15/16 in.) diamond drill hole which was being used exclusively for blastholes and permitted their substitution for diamond drill holes in a ring without alteration of pattern, burden, or explosives. The 2-in. bit also gave room in the hole for larger couplings and permitted the use of heavier rods and 3½-in. machines, increasing the

Jan 1, 1950

By Arthur F. L. Bell

Discussion of the paper of ARTHUR F. L. BELL, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1769 to 1799. WILLIAM A. WILLIAMS, San Francisco, Cal.-Is the Union Avila plant run as a topping plant or as a dehydrating plant? A. F. L. BELL, San Francisco, Cal.-Both. It takes off an average of 20 per cent. water besides topping the oil. Part of the crude oil is run through an electrical separator before running to the topping plant, but the entire crude averages about 20 per cent. when it enters the topping plant. DAVID T. DAY, Washington, D. C.-I suppose most of the work contemplated in these large topping plants is simply to deal with topping the oils with only a small percentage of water in them. A. F. L. BELL.-Not more than 2 per cent. of water can be handled in ordinary stills without causing trouble. At our Gavotte refinery, where the oil runs from 15 to 30 per cent. water, we carry 20 lb., pressure oil our stills to hold the framing down, we can do that with small stills, with large one's it would not be safe; but with a retort, the quantity of water contained in the oil does not affect its working. It simply means additional fuel to evaporate the water.

Jan 12, 1915

By John R. Wynnyckyj

Results of correlations between strength-development and sintering shrinkage occurring during induration are presented. A mathematical treatment of the shrinkage kinetics is, next, given and is based on the use of semi-empirical equations. The discussion stresses the significance of kinetic constants and activation energies in the assessment of iron ore concentrates for pelletizing and induration. Next, starting with the assumption that there is a need for parameters to characterize the iron-ore concentrates and relate these parameters to shrinkage-kinetic constants and balling behaviour, results of compaction measurements and pore structure characterization (mercury porosimetry) are presented and discussed.

Jan 1, 1977

By Neil Donnell, O&apos

MODERN mine maps are largely a product of evolution. The first mine maps used in the west were old composite maps with all the levels plotted on the same sheet. The composite was widely used and occasionally is seen even now. This type of underground map had serious limitations. One was the development of an indecipherable complex of workings around steep shafts. The other limitation was that of size; often when a working passed the limit of the sheet no map was made of it. These old maps have been superseded by the single level maps, laid out in squares or rectangles which can be expanded indefinitely in all directions. This produces a system capable of unlimited expansion in three dimensions, with all the detail of every working clearly marked and legible. A good set of mine maps should be laid out in blocks, all blocks of equal size. Each block should be limited by plane coordinates without overlap on bounding map quadrangles. At all times the direction of North should be indicated as an aid in remembering bearings of underground workings. It is desirable that all maps of whatever scale be plotted on sheets of uniform size. In fact, it is possible to make nearly all underground maps, surface maps and sections on sheets of the same size.

Jan 9, 1950

By M. Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molybdenum, lead, zinc, and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high, the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper prices; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1984

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By S. Whinery

In these times of sharp rivalry, both as to price and quality, among the makers and venders of engineering explosives, it is often desirable to be able to determine the relative energy or value of the various explosives offered for sale, in order to purchase intelligently ; or, having contracted for a large amount of an explosive of a certain standard quality, to be able to ascertain if the manufacturer keeps his product up to the specified standard. The simple and inexpensive apparatus described below was devised by the writer while engaged on the improvement of the Tennessee River, at MuscleShoals, under the direction of' Major W. R. King, U. S. Engineers, in the summer of 1879. It answered the purpose so well that it is thought that a brief account of it may be of interest to other engineers. It consisted, essentially, of an old blacksmith's anvil and a common striking hammer, such as is used for driving rock-drills. The anvil was placed face downward on solid, level ground. In what was then the top of it, a vertical hole, one and one-fourth inch in diameter and about one arid three-fourths inch deep, was made with a ratchetdrill. The surface of the anvil immediately around the drill-hole was made as true and smooth as possible with a file. Next, a new striking-hammer, weighing nine pounds, with a turned and true face, was selected ; and a handle, eleven feet long and about one and a half inches in diameter, was fitted into it so that it

Jan 1, 1886

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By Don Masson

MUCH has been written and many prophecies made on the subject of plastics as a replacement for metal, and the extent to which these materials will compete with each other for peace- time markets. (Metal is used in a broad sense to include all types.) But although certain synthetic resin materials have made considerable headway in war production, this change to plastics can hardly be regarded as a serious threat to the mining and metallurgical industries. Even today, the total yearly tonnage of plastic materials is approximately only 1 per cent of that of steel, and only a small fraction of this might be considered as actually replacing steel. However, these figures must not be taken as indicating that the importance of plastics in fields hitherto considered exclusively the territory of metals is negligible-far from it. Considering the comparatively minute tonnage of plastics now being produced in comparison to the output of metals, the number of applications where plastics have augmented or aided the sale of metals is considerable.

Jan 1, 1944

By R. Silent, N. A. Rousselot

The first producing wells completed in the Kettleman Hills arca were noteworthy for their high gas-oil ratios. As a result they became the object of criticism, and controversies arose based on their alleged lack of gas conservation. Ultimately protracted hearings ensued in the District Court of the area, and diverse rulings and subsequent modifications have been handed down affecting the permissible gas-oil ratios. When the Kettleman North Dome Association was formed in April, 1931, and the control of the major portion of the North Dome area vested therein, it was decided to produce only those wells which had a relatively low gas-oil ratio. Among the wells having the highest gas-oil ratio were the Milham Elliott No. 1 (the discovery well) and the Continental Elliott 12-8. drilled as an offset to it. Under the numbering system adopted by the Kettleman North Dome Association, these wells are now known as 88-2P and 1-12P, respectively. Milham Elliott No. 1 was originally drilled to 7236 ft., then redrilled to 7108 ft. The upper portion of the Temblor Horizon produces with a very large gas-oil ratio; production which actually consists of light crude oil with an accompanying large.volume of gas. Little was known as to the location of the Temblor formation at that time but it is now generally accepted that its top was encountered at 6180 ft., giving 928 ft. of penetration. Initial production was estimated at 4000 bbl. of oil and 80 to 90 million cubic feet of gas per day, giving a gas-oil ratio in excess of 20,000 cu. ft. of gas per bbl. of oil. This ultimately increased to a ratio of about 48,000 at the time the well was killed when it was producing about 1100 bbl. of oil and 52 million cubic feet of gas, with a flow pressure of 1200 pounds. The Continental Elliott 12-8 was drilled to a depth of 6876 ft. with the top of the Temblor at 6100, giving a penetration of 776 ft. The estimated initial production of this well was 7000 bbl. of oil and 130

Jan 1, 1933

By David G. Chedgy

The Meadow River No. 1 preparation plant, owned by Sewell Coal Co. which is a subsidiary of the Pittston Co., was commissioned in the spring of 1974. A survey of the environmental noise levels was conducted, and the dominant noise sources identified. An engineering program was initiated to reduce the prevailing levels to a point that the operator's exposure would be within compliance with the MESA regulation for ear protection. The program was continued until compliance was achieved and the attenuation factors for each abatement device recorded. The highlights of this program will be presented with a discussion of the practicality of the devices utilized.

Jan 1, 1977

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By Gerhard Derge

THE orientation relationships resulting from allotropic transforma-tions and the formation of segregate structures in metals and alloys have been the subject of the eight earlier papers in this series1. A brief summary of orientation studies has also been given by Sachs2. A survey of these papers discloses that the factors that determine the orientation relationship of a precipitated phase to its parent solid solution, as Well as the outward form and appearance of the new phase, are not completely understood. It is now evident that crystallographically analogous systems, as a rule, exhibit the same type of Widmanstätten figure and orientation relations, so that useful information is not to be expected from examination of a new alloy involving lattice combinations of which the orientation relationships are already known. Therefore, the determina-tion of the relations existing between lattice types that have not already been studied seems to be the most promising mode of attack upon the problem; both of the systems reported in this paper represent new com-binations of lattice types.

Jan 1, 1937

By William Hilliard

IN any manufacturing business, it is of vital importance that the management should know the exact cost of the units of production. Without such knowledge, a company can sell blindly in the open market, obtaining the best prices it can in competition with other firms, and manage perhaps to continue in business for a time; but at any moment, and especially in a period of falling prices, such a firm is at a loss to know exactly at what point it can sell at a profit and exactly how much it is losing per unit if it sells below that point. Furthermore, it is necessary not simply to know the exact total cost per unit, but to know definitely all the different-factors which enter into that cost. A firm manufacturing pocket knives had been doing a profitable business for many years when it began to earn smaller and smaller profits, until there was scarcely any profit at all being realized. Being unable to determine exactly what its future policy should be, it called in experts who studied the past records carefully and followed out for a period a better cost, system. Investigation then showed that on several different kinds of knives in common use, a small profit per unit was being made. On a number of special kinds of knives, of which the firm was very proud, it had been forced to cut prices under the pressure of outside competition and had believed that a small profit per unit was still being made on that product, while a detailed cost analysis showed that a loss was being incurred on each knife of that kind produced. It then became clear that the company must either give up the special line and concentrate wholly on the cheaper knives and extend their sales to territory not yet developed; or expand its plant and produce more of the higher grade knives and thus lower the cost per unit enough to make money on the higher grade knives also, if conditions warranted such expansion. Investigation revealed that the market for large quantities of the high-grade -knives was decidedly uncertain and that the most promising move would be to manufacture only the less expensive knives on a larger scale. That plan was carried out and the concern began again to make a better profit.

Jan 1, 1932

By Bernard H. Coyle, Robert N. Anderson, Judith A. Koperski

Between 6 and 8 million cars are shredded annually in the U.S. This shredded material is magnetically separated leaving a mixture of nonmetallics and nonferrous metals which can be further separated into its metallic and nonmetallic constituents. The metallic portion is a mixture of metalr; and alloys containing predominately zinc, and some aluminum, copper, and residual iron. Hydrometallurgical strategies are proposed for recovering the aluminum, copper, and zinc. The thermodynamic and kinetic behavior of the most promising alternatives to separation are discussed.

Jan 1, 1978

By H. M. Chance

The Taviche district is about 12 miles from the town of Ocotlan in the State of Oaxaca, and about 250 miles south of the City of Mexico. Its altitude rises to something more than 5,000 ft.; and although within the tropics (latitude about 17° N.) the climate is mild and salubrious, neither excessively hot in summer nor cold in winter. The phrase, "perpetual spring," which has been applied to it, aptly describes the weather during my stay. Sugar-plantations, bananas and other tropical and semitropical fruits flourish in the valleys, while the hills

Jan 1, 1905

By Guy W. Jordan, David P. Hale

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By David P. Hale, Guy W. Jordan

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By Nathaniel Arbiter, Arthur F. Taggart

THE fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. EXPERIMENTAL Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,' and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: 1. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. DISCUSSION OF RESULTS Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether

Jan 1, 1943