Search Documents

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

APPLICATIONS for loan contracts for the exploration, development and mining of strategic and critical metals and minerals are now being accepted by the Department of the Interior. The RFC is authorized and directed by Executive Order 10161 to make such loans but the Secretary of the Interior must pass on the necessity for the loan. Applications should be addressed to James Boyd, acting deputy administrator, Defense Minerals Administration, Department of the Interior, Washington, D.C. rather than to the Field Offices of the Bureau of Mines as was first planned. Application forms are not yet available but it has been learned that data accompanying the application should include the known quantity and grade of reserves, the anticipated rate of production, the equipment, supplies, and man power required for the additional production, etc.

Jan 12, 1950

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

By EL HANAF

The exploratory program initiated in Egypt in 1937 by four major oil companies was well under way early in 1939. Extensive gravity-meter surveys were carried out in the Sinai Peninsula and the Eastern and Western Deserts. Seismic and magnetometer work vas conducted on a restricted scale. The data collected justified wildcat drilling on structures located geophysically and/or geologically.

Jan 1, 1946

By H. T. Hildage

Although Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed .in the near future; that since 1903 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New lrork City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up of a " mine " in a large city, and a brief description of some of the &'mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

Jan 1, 1908

By Eugene McAuliffe

The term "mechanical mining" carries an ambiguity which justifies a preliminary word of explanation. . All mining activity conducted in this day is more or less mechanical; that is to say, power expressed in the form of electricity, steam or compressed air is used in some portion of practically every mining activity of consequence. "Mechanical loading" is more nearly correct than "mechanical mining" in reference to present practice. The first substantial effort made in the direction of mechanical mining, subsequent to the application of steam for hoisting and underground pumping purposes, was that of substituting for hand labor undercutting and shearing by power-driven machines. The undercutting of coal by hand represented at one time the most arduous task confronting the miner. Occupying a kneeling position in the thicker beds, or lying on his side in the thinner coal, the task was tedious and exhausting. The first attempt to substitute crude air-driven, and later electrically driven, "punchers," as the percussion type of machine was called, met with much the same opposition on the part of the workers as was expressed by workers in the other industries when any innovation, whether labor-saving or otherwise, was introduced. We should not be too critical of this attitude of mind shown by the mine workers. The peculiarly isolated character of the work carried on in semidarkness by a class of men who to a large extent lived and held themselves aloof from the other branches of society led long ago to the development of a craft consciousness which they have found difficult to surrender. It was not until 1891 that a definite record of the results obtained by the use of undercutting machines of all types was made available, the quantity undercut in that year totaling 6,211,732 tons of bituminous coal from all American mines. The volume of bituminous coal undercut by machines in 1928 totaled 369,687,007 tons, or 73.8 per cent. of the nation's production. In the light of this experience, we can properly feel that the work of introducing the coal-loading machine as a substitute for hand shoveling is making substantial progress.

Jan 1, 1931

By S. W. Miller

Most of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,' that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., he has since found large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than % in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top 1/16 in (1-5 mm.) of the weld, they were removed by the grinding or machining; also, welds 3/4 in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was decided to find where the rupture occurred in various kinds of welds made

Jan 1, 1920

By Henry Mulryan

THE largest and purest known deposit of diatomite is being actively mined and processed 3 ½ miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Manville Products Corporation. The workings FIG. 1-LOCATION OF DIATOMITE DEPOSIT AT LOMPOC. cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoc, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1936

By T. R. Cass

THE renewed interest in titanium, resulting from its increasing application as a structural material, has stimulated basic deformation studies on this metal. In the course of our work, we have developed a dislocation etchant and applied it to a perfection study of melt-grown single crystals as well as to a preliminary investigation of plastic deformation in titanium. The etchant, Keller's etch (21 cu cm HF, 64 cu cm HC1, 106 cu cm HNO3, and 160 cu cm H20), reveals the emergence of both grown-in and fresh dislocations on pure titanium and a-phase Ti-Al single crystals. Pits are produced only on surfaces within a few degrees of the basal plane; the more exactly parallel to a basal plane the surface is, the more distinct are the pits. The observed pit density, however, does not appear to depend on the surface orientation; the pits simul- taneously become less distinct as the misorientation from a basal plane increases. Etch times are short, a few seconds, for pure titanium; longer times are necessary for alloy crystals.

Jan 1, 1968

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral, rutile. United States consumption of titanium dioxide for these applications in 1973 was as follows: pigments, 891,000 st; titanium metal, 40,000 st (=24,000 st metal) ; and welding rod coatings, 10,000 st. The only commercially important titanium ore minerals at the present time are ilmenite, and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) states that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlines the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: "Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during the time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, Va., and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, Fla., for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for lowgrade sands, led to a return of activities in this area. The large deposits near Tahawus, N.Y., were brought into production in 1942 by National Lead Co. (now N L Industries Inc.), and by 1949 this company was the lead¬ing producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec." The beginning of the modern titanium metal industry was in 1948, when E. I. du Pont de Nemours & Co. produced the first metal. U.S. Bureau of Mines reports, which gave details of the Kroll process, together with the attractive properties of the metal for

Jan 1, 1975

By Andrew Hyslop

In our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber-tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys- tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1949

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese; they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way; there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution began. In the 1850s, miners began experimenting with liquid nitroglycerine on a limited scale. This was a very sensitive and dangerous explosive. Fortunately in the 1860s, Alfred Nobel succeeded in stabilizing nitroglycerine by absorbing it in kieselguhr-and a new product, dynamite, was born. With it, miners were able to unleash the great energy of nitroglycerine for blasting purposes. But dynamite was still a very sensitive explosive. In subsequent years, other explosives of various strengths and characteristics were developed, such as blasting gelatin, gelatin dynamite, ammonia dynamites, (all containing some nitroglycerine or nitrostarch), and liquid oxygen explosives. These products and their variations supplied the blasting trade for many years. A grained ammonium nitrate product containing some carbonaceous material entered the market in the 1930s. This explosive had below-zero sensitivity-meaning: a No. 6 blasting cap imbedded in it would not detonate it. A more sensitive initiator, called a primer, was needed to detonate this mixture. From Rags to Primacord to Solid-State The first initiator for an explosive charge was probably a rag slowly burning its way to the charge; this method was quite unreliable. Then came the burning fuse, which was an improvement. Next was the nonelectric blasting cap initiated by a fuse. With these initiators, a miner needed quick reflexes and good legs; upon lighting the fuse, he had to run immediately for cover. Development of the electric blasting cap that allowed for accurate timing eliminated this hazard; the electric cap, however, introduced other safety problems because of its susceptibility to extraneous electricity, e.g., ground currents, lightning, and static electricity. These caps also became available in millisecond delays. Development in the mid-1930s of Primacord, a detonating fuse insensitive to electrical currents or impact, further reduced blasting hazards, and is generally acknowledged as the safest known means of initiation. Eventually, Primacord millisecond connectors also became available for delay patterns in blasting. In the mid-1960s, the Primadet delay was introduced; it is a practical nonelectric detonator system that offers the precise timing of electric blasting caps-and is immune to the hazards or effects of extraneous electricity. Recently, Research Energy of Ohio, Inc. introduced a new type of solid-state blasting machine that combines a sequential timer and delay caps. It enables the efficient breakage of rock with a minimum amount of shock, ground vibration, and noise. Improvements in Blast-Hole Drilling World War II created an enormous demand for coal and other minerals in the U.S. and elsewhere. Great efforts and large amounts of capital were spent to find new mineral deposits and develop better mining methods. But while mechanization in mining proceeded at a rapid pace particularly in open-cut work, there was a definite lag in developing new or improved machines for drilling blast holes. The industry continued to depend largely on horizontal, churn, and pneumatic drills. No better machine was available for large scale production. The need for improvement in this phase of mining became more acute in the post-war years. Despite efforts toward further mechanization, mining costs rose rapidly because of mounting inflation and increasingly high wages. In most operations, drilling and blasting the overburden became the principal item of cost. Therefore, whatever size holes were being drilled, the holes had to be spaced so that any foot of the bore hole could be loaded with the maximum load required for the number of cubic yards of material that each foot of the hole was carrying. With the smaller holes that were being drilled, the proportion of drilling cost to the total drilling and shooting cost was much higher than it would have been with larger holes (because of the closer spacing required by smal-

Jan 1, 1977

By S. S. Clarke

LATE in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls Were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1947

By Eli T. Conner

My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its viciuity, which hare excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. Fortunately, there were no pupils in the building at the time; but the thought of the possible result, had the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken up and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Jan 1, 1912

Payloader The Frank G. Hough Co. has made available another four-wheel drive tractor-shovel. It has a 1 cu-yd bucket with 60 hp Diesel or 54 hp gasoline power optional. The use of large pneumatic tires, same size all around, and drive on all four wheels gives this new Payloader traction to work effectively in sand, mud and snow, and travel on pavements with- [ ] out injuring the surface. Rear wheel steer with power booster plus short wheel base makes it easy to operate and highly maneuverable. Four speeds in both directions insure fast travel speeds for transport and fast operating speeds on shuttle loading or similar operations. Bulldozer blade, crane hook, fork lift and snow plow attachments are available, quickly interchangeable with the bucket to further increase its multi-purpose usefulness. Circle No. 1

Jan 1, 1952

By John F. Elliott

STAFF: Editor, Gerhard Derge Acting Editor, Poul G. Shewmon Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, PO. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Rich-ard C. Cole, President; Karl L. Fetters, Past-President; J. H. Scoff, Vice President; R. L. Henneboch, Treasurer, R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairmon; T. E. Dancy, P. R. Gouwens, W. A. Krivsky, F. C. Longenberg, E. R. Morgan, R.R. Nosh, Poul Queneou, W.O. Philbrook, J. H. Scoff, L. L. Seigle, and M. E. Wadsworth. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: M. E. Wadsworth, Chairmon; R. E. Grace, Vice Chairman; D. H. Baker, Jr., G. M. Bell, D. H. Bridges, J. M. Cigon, G. W. Healy, R. A. Lewis, C. E. O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. E. Dancy, Chairman; A. Muan, D.W. Murphy, R. D. Pehlke, J. M. Uys, J. 5. Wagstoff, and R. G. Word. lnstitute of Metals Division: R. R. Nash, Chairman, H. H. Johnson, Jr., Vice Chairman; M. R. Achter, P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. 8. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. A. Girifalco, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, R. H. Richmao, H.C.Rogers, W. Rostoker, 0. D. Sherby. E. A. Steigawald, R. Steinitz, H. C. Stumpf, R. A. Swalin, W. A. Tiller, W. R. Upthegrove, D. Walton, H.W. Weart, and D. Wilsdorf. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign;$30per $7 50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1963 by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc....Registered cable address, AlME New York . .. Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . Second class postage paid ot New York, N. Y., and Ann Arbor, Mich. Volume 227, Number 4.

Jan 1, 1963

By Basil Prescott

A thorough knowledge of the peculiarities of this type of orebody is necessary in sampling these limestone replacement deposits. Oxidized ores are often overestimated because of error in determining specific gravity and actual cross-section of the orebody, and sulfide ores are often underestimated because it is difficult to scatter the samples so that they will accurately represent the area under consideration. This paper describes various methods of sampling and cites factors that enter into the estimation of these deposits. IN THE science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each successful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation.

Jan 3, 1924