Search Documents

By E. G. Spilsbury

AS a fresh illustration of the advances made in the past few years in the overhead-cable systems of hoisting and conveying, as applied to open-cut deep mining and quarrying, I would call attention to a further development of this system of transportation which has lately been put in operation i-n this State. A few miles above Williamsport, on the Susquehanna river, the Glen Union Lumber Company, of Pottsville, Pa., owned a large tract of valuable timber-

Jan 1, 1892

By Robert Schorr

PAGE 1. Introduction,........... 82 2. Characteristics of Briquettes,........ 87 3. The Manufacture of Coal- and Coke-Briquettes,.... 89 Binders, Organic and Inorganic,...... 90 Mixing,...........94 Presses, Continuous and Intermittent Action,....95 Cost of Briquettes and Sales-Prices in Various Countries,.. 99 4. The Manufacture of Peat-Briquettes,......101 Solid Peat-Slabs,.........101 Solid, Carbonized Peat-Briquettes,......103 Estimates of Cost of Operating Peat-Briquetting Plants,... 105 5. Manufacture of Mineral-Briquettes for Metallurgical Processes,.. 108 6. Manufacture of Artificial Stone-Masses,......112 7. Bibliography,...........115 Introduction. Briquetting is apparently a very simple operation, yet it has offered so many mechanical and chemical difficulties that it required almost a century to place it on a commercial basis. Since 1860, however, the progress has been steady and satisfactory, and to-day, for most of the European coal companies, the briquette-plant is a very profitable investment. Among the many applications of scientific knowledge to further economy by recovering and utilizing by-products and raw materials, there is possibly none which deserves the attention of Americans to a higher degree than briquetting. The recent miners' strike in Pennsylvania, which resulted in a scarce and irregular supply of coal at a high price, has advanced the possibilities for briquetting, and as a consequence public interest has grown rapidly. While the manufacture of coal-briquettes is not new in the United States, adverse conditions and sometimes lack of

Jan 1, 1905

By F. A. Crossley

The titanium-rich end of the Ti-A1 system has been investigated up to 35 at. pct A1 (23 wt pet). One conzpound Ti3Al was found to occur between primary a and TiAl. It is ordered hcp with DO19 structure, it has virtually no solid-solubility range, and it has a closed maximum at about 875°C. OIL either side of the compound are a +Ti3Al two-phase fields. The limiting a1uminum solubility in primary a at the titanium-rich end is indicated to be 7.5 at. pct A1 (4.4 wt pet) at 550°C and about 6.8 at. pct Al fl wt pct) at 500°C. Quenching alloys from above the a + Ti3Al two-phase field produces the following structures with respect to alloy composition: Up to 13 at. pct A1 (7.8 wt pet), a solid solution; from 15 to 18 at. pct A1 (9 to 11 wt pct), shear transformation product or martensite; from 19 to approximately 30 at. pct (11 to 19 wt pet), submicro-scopic coherent Ti3Al in an a malvix. The twin hcp phase fields reported in the literature are the result of nonequilibrium corzdztions. Ti-A1 alloys, once partitioned by dwelling- in the a + ß phase field during either hot working or heat treatment, are extremely difjicult to homogenize at temperatures below 1000°C. Such partitioned alloys exhibit the characteristics or symptoms of two-phase materials, and may be said to suffer the "twin-phase syndrome". THE earliest investigations of the Ti-A1 system by Ogden et al.1 and Bumps et al.2 reported wide solubility of the primary solid solutions. Aluminum was reported soluble in the low-temperature allomorph to the extent of 37 at. pct (25 wt pct), and the first intermediate phase was reportedly TiA1. Somewhat later Kornilov et al.3 reported a similar diagram with phase boundaries displaced towards lower aluminum contents and higher temperatures. Beginning about this time (1956) reports in the literature made it very clear that one or more intermediate phases occurred at lower aluminum contents than TiAl.4-17 These reports included five major investigations of the titanium-rich end of the Ti-A1 diagram.4,12,14,16,17 Three of these diagrams show two two-phase fields below 37 at. pct Al, while two of them show a single two-phase field. The existence of the phase Ti3A1 is firmly established and is included in each of the diagrams, except one—that of Sato and Huang.12 The new phases are reportedly hcp and differ from primary a only slightly when disordered, and when ordered the "a" parameter is approximately one,4,12,15 two, 6-10,13,14 or four14 times that for primary a. Beyond this, however, the diagrams are remarkable for their lack of agreement. Two tacit assumptions are usually made in phase-diagram determinations of metal systems. These are: 1) equilibrium anneals bring the alloy to equilibrium or to indistinguishable closeness to it, and 2) equilibrium conditions established at elevated temperatures are either "frozen" by rapid quenching for evaluation at room temperature, or quench-transformation products are recognized as such. In the current investigation evidence was obtained that over substantial composition ranges neither of these two conditions was met in any of the more recent major investigations. I) MATERIALS, METHODS, AND TECHNIQUES The alloys of this investigation were prepared by nonc on sum able electrode arc melting. Materials used in the preparation of the alloys are summarized in Table I. The investigative tools employed were: optical and electron microscopy, differential thermal analysis (DTA), disatometry, X-ray diffraction, electron diffraction, and resistometry. Alloys for microscopic and X-ray investigations were prepared as 15-g melts. Alloys containing from 7 through 11 at. pct A1 were hot-rolled out of a furnace at 900°C, from 12 through 15 at. pct out of a furnace at 1000°C, and from 16 through 18 at. pct out of a furnace at 1125°C. Alloys containing more than 18 at. pct A1 could not be hot-rolled. The ingots were covered with Markal coating prior to hot rolling to minimize atmospheric contamination. After hot rolling, alloys containing up to 15 at. pct A1 were ground and pickled to remove 7 mils from each surface; alloys containing 16 and 18 at. pct A1 were skinned to a

Jan 1, 1967

By M. Baeyertr

Since 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallogmphy. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types. Radiography Radiography is the field in which the application of X-rays has had most general appeal among the industries which produce or use metals and alloys. Equipment permitting the examination of heavy sections of metals less permeable than aluminum or other light alloys requires apparatus capable of generating hard X-rays over a considerable period of time. The equipment used in the work presented in this paper is practically identical with that described by Fink and Archer in their paper on radiography in industry and is easily capable of penetrating 1/8 in. of lead. Radiography is used in two major groups of problems: (1) in the development of cquipment and tools and (2) in studies of materials. So far there has been no instance in which the use of radiography for routine inspection is justified. This is partly due to the fact that the manufacture of telephone apparatus involves the production of many identical parts by standardized procedures and equipment that has had development and trial before being put on a regular production basis. It is during this stage of development of equipment and tools that radiography has been used to particular advantage.

Jan 1, 1931

By Campbell Osborn

From the viewpoint of practical economic engineering the main value in studies of demand and supply lies in the information they give concerning the next movement of price. The title of this discussion is too comprehensive for detailed analysis and it will, therefore, be narrowed to the question of price measurement. The oil operator is interested primarily in net profits. Prices, costs and production determine them. Production is here used in its broadest sense. It includes refining and marketing. It is an operating problem. Prices and costs are economic considerations. Though costs are an important element of prices and profits, the subject is too large to be treated in a brief paper of this sort. In the long run, costs govern prices, but for the purpose of gaging prices in the immediate future the relationship of current demand and supply are more significant. Operating, expansion, retrenchment, sales and storage policies of oil companies are largely influenced by the feeling of executives concerning this relationship. The stockholders of companies whose executives are wrong may suffer. Investors who err in their judgment may likewise lose. On the other hand, oil companies and investors who appraise these factors correctly and move accordingly will profit. It is an important subject worthy of careful consideration. The author has been asked to discuss the subject for 1928. From the beginning of the year until the first of June, as illustrated by Fig. 1, over-supply prevailed in the face of restricted production, but from June to September, with record consumption, demand slightly exceeded supply and oil came out of storage in the United States as a whole. One of the main problems of the oil man is to decide whether this condition will continue and what the next movement of prices will be. Before he can do so he must have an understanding of the underlying conditions and of the facts that led to the present situation. With these facts in mind he is in a position to measure the effect of the present relationship of demand and supply on price and is afforded a perspective that may enable him to look ahead for a short period of time. The practical

Jan 1, 1929

By L. D. Clark

Pay-out, the ratio of capital expenditure to annual cash return can be very revealing when employed to gage the merits of a proposed mining venture. It is a quantity, numerically but not physically equal to a factor, by which cash return may be discounted to equal required investment. The fewer the pay-out years, the greater the average annual earning power of the project. Considerable material has been written in the past about the most important and difficult problem mining management faces in evaluation of a property: the optimum production rate for the venture. What daily capacity should be adopted for the proposed operation that it may be the most rewarding to those underwriting it? H.C. Hoover has said, "The most important objective is the least cost per ton mined; and minimum working costs can only be gained by the most intensive production." Theoretically and practically, the quicker the ore is removed, the more profitable should be the venture because of the saving in fixed charges, the consequent lower unit costs and the interest unearned by the profit from the unmined ore. Yet, such performance will be tempered by policy and a restraint imposed by the ratio of capital expenditure to annual cash return. * The 'Annual net profit after taxes but including depreciation and depletion allowances. former will be based upon an analysis of the economic climate anticipated, with its many ramifications including the demand for the product, prices, tax laws, the conduct of labor and related wage scales. The variables and intangibles involved in estimating the optimum production rate for a mine do not readily lend themselves to mathematical relationships or equations and the problem can become complex indeed. The more readily applicable and relatively faster appraisal method will be used which, in addition to being reasonably adequate in most cases, will serve as a guide, should a more expanded and detailed estimate be desired. The first question is what is company policy with respect to the rate of investment return? This will depend on that significant period of time referred to as the pay-out, which can be defined as the estimated interval during which capital investment is returned through application of annual cash return to its recovery. Expressed another way, it is the ratio of capital expenditure to the annual cash return. For example, if the capital investment is $C and the annual cash return is $A (after Federal tax), then $C/$A = the pay-out period in years. That is to say, if $C = $1,500,000 and $A = $214,000, then which is the mathematical expression for the period of time it takes to recover the funds originally invested in a mining enterprise. The relationship yp = $C/$A can be useful — an expression which requires only the significant tern yp to be fixed; in other words, the long range investment policy. For what is the pay-out period but an expression of that policy in terms of the speed, within practical limits, with which an individual or company may want to recover capital expenditure? A policy by which pay-out will be fixed is imperative. This ratio must lie within relatively narrow limits governed by what is economically feasible. It cannot be too low, rendering the ratio impractical or absurd, nor too great, delaying the return of capital for reinvestment beyond a commensurate interval. What pay-out will govern this policy? Federal corporate taxes would seem to present the best measure. Consider mining in Canada where new mines are exempt from Federal income tax for 3½ yr from date of first production. This exemption expressly allows The Act states: "A corporation . . . i s not required to include the profits . . . for the period of 36 months commencing with the day on which the mine came into production in reasonable commercial quantites." a company to recover capital expenditure during the early stages of production. With such an incentive, it is logical to strive for as much capital redemption as possible during this period. Thus, 3½ yr would be a major contribution to the pay-out in Canada. Furthermore, it generally takes from 1½ to 3 yr to develop

Jan 1, 1963

By Mayumi Someno, Kazuhiro Goto, Masahiro Kawakami

The apparent rates of decarburization of liquid alloys of Fe-C, Fe-C-S, Ni-C, and Co-C systems and the rate of oxidation of solid graphite with pure carbon dioxide gas and with gas mixtures of carbon monoxide and carbon dioxide have been measured in the temperature range of 1000° to 1600°C. The cotnposition of carbon dioxide and carbon monoxide gas at the reaction surface has been measured by oxygen concentration cells with the ZrO,-CaO solid electrolyte. 1) The apparent rates of the carbon removal are essentially the same for all the cases of solid graphite, Fe-C, Fe-C-S, Ni-C, and Co-C systems under the same experimental conditions. 2) The apparent rates are independent of the carbon content in the high carbon concentration range but very much affected by the flow rate and the gas composition of the CO-CO2 reactant gas mixture. The ratio of the gas consumed by the reaction to the total quantity of the supplied gas is very large under the present experi~nental conditions. 3) There is a concentration gradient of' carbon dioxide in the vicinity of the reaction surface and the content of CO, becomes extremely small at the reaction surface. 4) A large time fluc-tuation of the gas composition was observed. This jluctuation implies the presence of unstable flow in the gas phase in the vicinity of the reaction surface. THE decarburization of molten steel by an oxidizing gas or by slag may be one of the most important chemical reactions in steelmaking processes. Nevertheless, the kinetics of this heterogeneous chemical reaction do not seem to be well-solved even with the previous studies. Although the conditions for the reaction in steelmaking processes are quite different from those in the laboratory scale, some critical experiments may give information on the mechanism of the decarburization. From the previous work,'-' it is known that the rate of the decarburization is independent of the carbon content in liquid iron with more than about 0.2 wt pct C when the oxidizing gases are supplied to the surface of liquid Fe-C alloys on a laboratory scale. Two rate-controlling steps have been proposed for the decarburization of liquid iron with the high carbon content: one is the surface reaction control proposed by Swisher and Turkdogan;' the other is that the rate is controlled by the gaseous diffusion through the gaseous stagnant layer. proposed by Baker. Warner, and Jenkins.7 and also by .Ito and Sano.2 In the present study, some experiments have been carried out for the evaluation of these rate-controlling steps in the decarburization of liquid iron with high carbon content. The apparent rate of decarburization of liquid iron has been compared with the rates of carbon removal of liquid Ni-C, Co-C, and solid graphite under the same experimental conditions. The composition of carbon dioxide and carbon monoxide gas at the reaction surface has been measured by oxygen concentration cells. I) EXPERIMENTAL PROCEDURE Fig. 1 shows the schematic diagram of the reaction chamber. Solid graphite and liquid metals were contained in an alumina or magnesia crucible of 32 mm ID and 35 mm in height. The samples were heated by high-frequency induction and the temperature was measured by the calibrated optical pyrometer. The temperature was held constant to within 10°C. The re-actant gases were supplied to the surface of the samples through the quartz tube of 8.0 mm ID. The distance from the end of the quartz tube to the surface was 20 mm. The block of high-purity graphite was cut and shaped to the inner profile of the crucible. The height of the shaped graphite was 18 mm, which corresponded to the depth of the liquid iron of 100 g. About 100 g of Fe-C alloy (4.20 to 4.40 pct C), Ni-C alloy (1.84 pct C), Co-C alloy (1.85 pct C), and Fe-C-s alloy (4.35 pct c, 0.5 or 1.0 pct S) were melted in the crucible. The reactant gases were pure CO, and gas mixtures of CO-CO,: the flow rates were controlled by capillary flowmeters with bleeders.

Jan 1, 1970

By Franklyn W. Oatman

In order that the conditions which obtain in an oil well may be readily understood, a brief description of a typical California well and a number of the phenomena accompanying same will be given. That the necessity for the exclusion of water be realized, the effects of water intrusion, a description of methods of prevention, .and a discussion of causes of failure will be presented, followed by a summary and recommendations. Fig. 1 shows a section of a typical well which illustrates the relation of oil sands to overlying strata. It indicates a deep water sand separated from the oil sand by shale, and the proper place for the final shutting off of water. In this well a comparatively thick stratum of compact shale protected the oil from overlying water so that the operation of landing the water string was a simple matter. In some wells the protecting stratum may be only from 3 to 5 ft. thick and very careful operation is necessary in order to land the water string of casing properly and not puncture through to the oil sand. The cases just cited are common, but occasionally, after excluding overlying water, productive oil sands are drilled through in the expectation of finding more productive underlying sand, and a water-bearing stratum is tapped. In this case the problem is the reverse of the normal; water must be prevented from ascending rather than descending. A discussion of well-drilling methods is not within the scope of this paper, except such operations as pertain to shutting off of water. A brief outline of the several conditions which may accompany drilling follows. Some or all may be present in any particular case. The direct relation of these to prevention of intrusion will be discussed in detail further on. In drilling, the hole becomes more or less irregular in shape, and rough, and as the casing follows the bit into the well it does not fit snugly against the walls. As a result, water may descend between the casing and walls of the well. If a circulation pump is not used during drilling, the hole is simply punched through and the pulverized material removed from the well by means of a bailer. If circulation is maintained there is a continual flow of water down inside the casing and up around the outside between the pipe and the walls of hole. This keeps an open space around the pipe.

Jan 1, 1915

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.' exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962

By E. C. W. Perryman

The recovery and recrystallization characteristics of superpurity aluminum have been investigated using electrical resistivity, X-ray line breadth, and hardness measurements for the former and the micrographic method for the latter. The three different properties recover at different rates and have different activation energies. The recrystallization results agree well with Avrami&apos;s theory and furthermore indicate that the perfect subgrains formed during recovery are not the nuclei for re-crystallization. WHEN a metal is plastically deformed, its physical and mechanical properties generally undergo considerable changes and by subsequent annealing these changes are partly or wholly annihilated. Thus, a recovery process can be discussed, taking this term in its general sense. In practice, however, there is reason to discriminate between two apparently different processes, one most easily followed at low temperatures, in which the properties return to an almost constant value between that of the cold worked and fully annealed material, and a second process in which the properties return to their original values before cold working and which is accompanied by the formation and growth of new grains having an orientation different from that of the matrix. In this paper the word recovery will be taken to mean the changes in some property as a function of annealing time which occur either without the appearance of new grains or under conditions such that the new re-crystallized grains are very small (= 2 microns), are very few in number, and substantially do not affect the property being measured. This definition is rather abitrary, for it will depend upon the sensitivity of the technique used for the observation of new recrystallized grains, which in the present work was about 1 to 2 microns. However, it is helpful to use the term recovery in this sense and to reserve the term recrystallization for the processes of nucle-ation and growth of new grains in the cold worked matrix. Although considerable work has been done on recovery and recrystallization, most workers have based their study on the measurement of one or perhaps two parameters. Since very small amounts of impurities have such a profound effect on the recrystallization characteristics of a pure metal, it becomes extremely difficult to correlate one piece of work with another. With this in mind, the present work on recovery and recrystallization was done on the same material. Experimental Procedure Material Used and Fabrication: The composition of the superpurity aluminum used throughout this investigation was 0.002 pct Cu, 0.003 pct Fe, 0.003 pct Si, and <0.001 pct Mg. The ingot was hot rolled to 0.250 in., annealed, and cold rolled to 0.034 in. A large number of reductions and intermediate anneals were carried out so as to produce material with a minimum of preferred orientation and maximum homogeneity. For the recovery part of the investigation, the final cold reduction was 20 and 80 pct and for the recrystallization part, 20 pct. After each pass in the cold rolling process, the material was quenched in cold water in order to keep the rolling temperature as near room temperature as possible. Annealing Procedure: For the recrystallization work, specimens 1x1 in. were cut from the 0.034 in. cold rolled sheet and a hole was drilled in each through which a wire was threaded to support it in the salt bath. The temperature of the salt bath was controlled to +2°C and the time taken for a specimen to reach temperature was approximately 5 sec. These 1 in. squares were then divided into three groups, one of which was given 5 min at 318°C and another 2 hr at 244°C. These treatments were such that recovery was almost complete and a well defined subgrain structure produced. Separate specimens of each group were annealed for different times at 301°, 318°, 355°, and 373°C, i.e., three specimens for each annealing time. The delay between finish of cold working and start of annealing was about 1 hr. For the recovery work, strips 0.062 in. thick were cut from the cold worked sheet, annealed, and then given the last cold rolling operation. This was done for each annealing temperature. By this means it was possible to minimize the delay between cold working and annealing. In general, all measurements were carried out within 1 hr of the last cold rolling operation. Annealing at low temperatures was done in an oil bath the temperature of which was maintained constant to +1°C. Electrical Resistivity Measurements: Strips 20x0.5x0.05 in. were machined and the electrical resistance measured using a Kelvin double bridge. Measurements were made in an oil bath maintained at 20rt0.1°C. The same specimen was used for the complete isothermal annealing curve.

Jan 1, 1956

By R. A. Vandermeer, P. Gordon

The study of recrystallization in cold-worked metals is complicated by the impossibility of making direct three-dimensional optical measurements. Metallo-graphically, theinternal three-dimensional features of samples must be inferred from their intersections with the two-dimensional plane of polish. The inherent difficulties involved in this procedure have led— particularly during the last few years—to some instances of rather doubtful interpretations of experimental data in terms of nucleation and growth rates in recrystallization. In the present paper an analysis ; is given of the recrystallization characteristics in a polycrystalline alloy containing 0.008 wt pct copper in ZONE-refined aluminum *and an effort is madf to reemphasize the necessity in such studies for attention to the proper statistical relationships between one- two- and three-dimensional features of opaque samples. It is shown that, in common with several recently described cases for other types of transformations,1-5 recrystallization in this alloy can best be rationalized on the basis that all nucleation took place essentially at time zero—i.e., there is no significant time-dependent nucleation during annealing—and that the kinetics are controlled exclusively by the growth-rate parameters. This is true despite the fact that the number of

Jan 1, 1960

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-&apos; proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible &apos;References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By M. P. Tixier

In several log interpretation methods, water saturation is evaluated by use of the ratio of the readings of a short spacing resistivity device and a long spacing resistivity device plus information on the mud filtrate and connate water resistivities, which is often derivable from the SP. These methods are valid over a certain range of conditions, usually specified by moderate invasion and R.. greater than R,. Since these methods involve no explicit evaluation of the formation factor, F, the saturafiion so found may be used in the standard Archie equation to derive a computed formation factor which, as a check, may be compared with the formation factor known from other independent measurements. Discrepancies in the two values of formation factor generally indicate that the ratio method is not within its range of applicability. If the computed F is too low, the corresponding S, is too low; if the computed F is too great, the corresponding S, is too great. By means of this "porosity balance" check, and some knowledge of the probable conditions of invasion, the interpretation can often be improved. The poqosity balance check is discussed for the cases of the Induction-Electrical Log Interpretation Method, the Rocky Mountain Method, and the R.,/R, Method. For the first method, a discussion is also given for the case of shaly sands. INTRODUCTION Al though many logging tools are available to obtain a practical value of porosity, the only logging method reflecting the water saturation is electrical logging. Water saturation is commonly computed from electrical log data by means of the basic Archie formula, Where F is the formation factor, R, the resistivity of the formation water, and R, the true resistivity of the formation. One difficulty in this procedure is a possible error in the evaluation of R, from the logs— for example, in the case of very deep invasion. There is no possibility, inherent in the procedure, which would provide a check of the accuracy of R, and, hence, of the computed saturation. Other approaches have been proposed which are based essentially on the ratio of the readings made with two dzerent devices: one device, with a short radius of investigation, provides a value close to the resistivity of the invaded zone; the second device, with a long radius of investigation, gives a value close to the true resistivity of the bed. By these methods, the determination of saturation is made independently of any direct knowledge of the formation factor. Therefore, if the formation factor (or porosity) is known from other sources (core analysis, neutron log, MicroLog . . .), it becomes possible to take advantage of this additional information in order to check the value of saturation derived from these latter methods. Inasmuch as this proposed check procedure relies on a knowledge of the value of formation factor or porosity, it has been deemed appropriate to call this verification a porosity balance. The purpose of this paper is to discuss the principle and the application of the porosity balance, depending on the method of interpretation being used. Basis of the Method There are in existence three interpretation methods by means of which the water saturation can bc found without a knowledge of the formation factor (or porosity). As just stated, they are based on the fact that the ratio of the two resistivities (one measuring the resistivity close to the hole, the other measuring the resistivity far from the hole) is independent of the formation factor since it affects the two resistivity measurements in the same way. Chronologically, the resistivity ratio methods are: (1) the Rocky Mountain Method, which has been used since 1943 and was explained in a paper in 1949;&apos; (2) the R../R, Method or Shaly Sand Method, presented in 1954, which permits the calculation of the water saturation in both clean and shaly sands2; and (3) the Induction-Electrical Log Method, presented in 1957 for the interpretation of the induction-electrical log combination." Each method requires certain definite conditions in order for the interpretation to be reliable. The porosity balance method will let us know whether these conditions are fulfilled. In clean formations we know that the fundamental Archie relation (Eq. 1) must always be verified. This relation can be rewritten:

By K. V. Hoover, D. M. Lapham

In Pennsylvania, 310 sampled sites of clay and shale have been studied with regard to potential use, lithology, physical properties, fired properties, major-element chemical analyses, and quantitative five-component X-ray mineralogy. Approximately 80% of the samples are of some potential use. Binary correlations of test data vs. potential use indicate that certain empirically determined parameters may be critical. These are: lithology, particularly for medium to superduty refractories and lightweight aggregate; kaolinite content for refractories vs. low-temperature fired product sources; quartz analyses with an apparent necessary minimum quantity for brick; quartz content, which is low in high grades of lightweight aggregate; mica content, which is low for refractories and possibly high for lightweight aggregate; total iron, which is low for refractories and shows a 4.0% minimum for lightweight aggregate; carbon dioxide, which is low for refractories, beneficial in lightweight aggregate, and probably restrictive for some tiles; chlorite-vermicalite, which is low for refractories and possibly beneficial in lightweight aggregate. In Pennsylvania, clay and shale materials constitute one of the state&apos;s major economic mineral resources. To date, the testing program indicates considerable development potential in brick, tile, and lightweight aggregate industries and perhaps a future potential for aluminum from shales that exceed 20% AID..

Jan 1, 1972

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475&apos; to 1525&apos; C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475&apos; to 1525&apos; C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By J. B. Cheatham, C. E. Murphey

Presently, computer control of Borobolic direction cannot be obtained during drilling, and most straight-holc drilling methods attempt to resist hole deviation rather than control direction. Many of the theories advanced as possible explanations of the cause of hole deviation are Summarized berein. A new correlation of physical partables is introduced to indicate bow factors such iis drill collar stiffness clearance and hit weight influence borehole deviation, .A methord is proposed for predicting the rate of change of hole angle when drilling conditions are changed. INTRODUCTION Control of borehole direction during drilling can be difficult and costly. Unintentional crooked holes are often lrilleti in dipping formations and many times directional drilling is required when the surface location is not directly above the target area —- for example, at offshore and mountainous locations. Prilllng progress can be greatly hindered in either air or liquid drilling when it be comes necessary to use low bit weight to prevent excessive hole angle build-up. If hole inclination becomes too great, drill pipe drag becomes excessive and fishing risks are increased, logging is more difficult and problems of differential sticking, key seating and fatigue failures may be encountered. Dog-legs and key seats are more serious problems than steep inclination angles: therefore, reducing rate of direction change is preferred to attempting to maintain absolutely vertical holes. Consequently, a straight inclineti hole is preferable to a nearly vertical crooked hole containing numerous dog-legs. In this paper, theories of the cause of hole deviation and analyses of drill string behavior under down-hole conclitions are summarized. Methods for computing hole deviation are presented und systems for resisting deviation as well as neans for provic!ing control of holt- direction are iliscusseI. A new correlation of physical variables is introduced tu indicate how factors such as drill collar stiffness, clearance and bit weight influence borehole deviation. A method is oroposeti for predicting the rate of change of hole anFrle when drilling conditions are clianged. IIEVIEU&apos; OF PREVIOUS WORK ON HOIaE DEVIATION Significant progress in the theoretical analysis of hole deviation problems has been made in the past 1 5 years. The pioneering work has been primarily a result of the efforts of Lubinski and Woods.l-5 In 1950, Lubinski 1 considered the buckling of a drill string in a straig:rt vertical hole, a problem also considered by Willers6 in 1941. It wns concluded that very low bit weights must be used to prevent hole deviation resulting from drill collar buckling. The use of conventional stabilizers was proposed2 in 1951 by Mac Donald and Lubinski as a method for permitting greater Sit weights to he carried without drill collar buckling. These authors pointed out that a 2° nearly vertical spiral hole can cause severe key seatinp, and drill pine near, wilereas n 3 straight inclined hole with deviation all in one direction, while not vertical, will not result in serious drillirig or producing problems. Studies were continued with an investigation of straight inclined holes by Lubinski and Woods3 in 1953. In this paper they concluded that perfectlv vertical holes cannot be drilled even in isotropic forriations unless extremely low bit P-eights are used. .l&apos;l~ey postulated that constant drilling conditions produce holes of constant inclination angle and varying conditions cause the hole to drill at a neiv equilibrium angle. This analysis was not concerned with drill string buckling since it was based on an equilibrium solution in which the ~irill string Was presumed to lie along the lower side of the hole abcrve the point of tangency. Weight of the drill collars below the point of tangency tends to force the hole toyard the vertical, whereas the weight on hit tends to force the hole aurav from the vertica l. The concept of an anisotropic formation Lvas introduced as an empirical method for explaining actual drilling data and as a means for extrapolating known deviation data to otiier conditions of hit

Jan 1, 1967

OF THE many categories into which scientific knowledge has been arbitrarily divided, the one which has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. To one who has had no such course or whose auld acquaintance with the subject has all but been forgot, such application is all too often thwarted by the abstruse presentations of the subject found in many of the available textbooks. AS a tool for the control of a complex process involving many chemical reactions, physical chemistry can become very valuable. The specialist who is using this tool for many purposes and perhaps contributing to its development will want to know a great deal more about it than can be included in this book. He will be interested in its history, its accomplishments and limitations, and its applications to many and varied problems. To the steelmaker or metallurgist, however, it is only one of a number of tools that he must use. He is willing to forego the detailed study of its inner workings in order to concentrate upon the development of skill in its application. It is the purpose of this chapter to present a simplified view of physical chemistry as a tool of great potential usefulness. This purpose and the desire for brevity have required the elimination of many of the gadgets with which the tool is usually adorned. It is hoped that this simplification will be conducive to clear understanding. The beginner is urged not to overlook the more extended treatments of the standard textbooks.* He is assured at the same time that the basic tool is sound and serviceable and is guaranteed to give satisfaction if regularly lubricated with common sense. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly

Jan 1, 1944

By M. Van Siclen

THE outstanding fact in connection with dust disease in. the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some. of its better organized centers, but the average independent non-. union workman continues, as of yore, to suffer the toll of disability and. even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of. dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913.E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933