Search Documents

By A. J. Garnier, N. H. van Lingen

Rock downhole is known to be lesc. drillable than when brought to the surface. This must be ascribed mainly to the presence under downhole conditions of a pressure differential across already made chips, which hinders their being lifted. The pressure differential has partly a static and partly a dynamic origin. Balling-up of bits is another consequence of this pressure differerztial. Reduction in penetration rate owing to an increase in the strength of the rock is governed by the difference between the mud pressure and the pressure of the for/nation pore liquid. Rotationally symmetric geostatic stresses have 170 effect on drillability. Fracture of rock when drilling will be brille in most cases. The above is supported by laboratory drilling experiments with drag bill and roller bits an elevated mud, pore, and confining pressures On rocks differing in strength and permeability. INTRODUCTION In oil well drilling drillability of rock is found to decrease with increasing depth of the hole. Naturally deep rock will be more compacted and, therefore, harder to drill than shallow rock of the same type. However, apart from this the drillability of a sample of deep and compacted rock brought to the surface is generally much higher than in its original location downhole. In view of the economic implications of this reduction in drillability, it seems worthwhile to analyze its causes. The origin clearly has to be sought in the difference of environment. The only conceivable factors would seem to be the presence of mud under pressure, the pressure of the formation pore liquid, and the overburden of the rock. Down the borehole the rock is compressed triaxially by mud pressure and overburden. It is well known that the strength of rock is increased when confined by external pressure1. Various authors have, therefore, ascribed the difference in drillability mainly to the strengthening of rock by triaxial compression. Another factor, mentioned by Bobo and Hoch5, is that forces. including "pressure differential forces", tend to hold a dislodged particle in place. However, the conditions determining their magnitude are not clarified nor is their effect on drilling rate assessed. In the laboratory, drilling experiments on pressurized samples of rock yielded evidence that pressure differential forces holding the chips down are the major factor in reducing rate at depth. This paper describes the experiments and shows how the results enable both a qualitative and a quantitative interpretation of the factors determining the effect of chip hold-down on drilling rate. The implication with respect to balling-up and jet action is also discussed. The greatcr part of the experiments were performed in the pressure vessel shown in Fig. 1. The spacc between the sample of rock and the vesscl is divided by "0" rings into three separate chambers. The rock sample is confined laterally by pressurized oil in thc middle chamber. Penetration of oil into the sample is prevented by partly jacketing it with brass foil. Thc pressure of the drilling fluid in the hole can be adjusted via the upper chamber. Permeable rock specimens arc water saturated before being drilled. With a properly plastering mud as drilling fluid the pressure of the pore water can be adjusted independently via the lower chamber.

By John G. Koert, Koert D. Burnham, John G. Broughton

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.' Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By Koert D. Burnham, John G. Broughton, John G. Koert

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.' Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By John S. Brock

INTRODUCTION The Oxford Dictionary says that the word "promoter" has usually been used in an opprobrious sense since at least 1876. This popular image of mining promoters is of cigar-chomping shysters and Brooklyn-Bridge vendors, improving their standard of living with the aid of funds raised through the sale of stock to little old ladies. It is unfortunate that mining promoters are considered crooks until they can prove their integrity and honesty by finding a mine. A common rule of thumb states that for every 1,000 prospects, 100 come to be drilled, and one becomes a mine. However, it is also a statistic that there have been mining promotions, where money raised has gone elsewhere than into the ground; Junior exploration companies can be handy vehicles for unscrupulous financial activity. One must remember though that every stock exchange has had its share of sound mining promotions that, because of the one in 1,000 odds, have failed for legitimate reasons. The promoter must be able to rationalize the worth of a mineral discovery which, on an industry- average basis, probably cost more to find than the discounted value of its net return, which return is not an assured percentage of invested capital, and furthermore, is ultimately from a wasting asset. So, it is easy to understand why the promoter must constantly justify the credibility of his operation to his grubstakers during the course of the "five phases of exploration," those being (1) euphoria, (2) disillusionment, (3) search for the guilty, (4) punishment for the innocent, and (5) distinction for the uninvolved. The promoter with the exploration organization that does not have the benefit of positive cash flow, by definition for the sake of this article, works for a promotional outfit, a Junior Company, that must raise its exploration budget from a variety of sources. Promotion, as discussed here, will not entirely refer to the formation and operation of a joint- stock company but rather to the overall methods of raising risk capital for mineral exploration ventures from outside sources. THE NECESSITY OF PROMOTION In Canada, the publicly financed Junior Company has had an enviable record of mine-finding success. In the Province of British Columbia alone, the discovery of fifteen out of twenty-four mines has been as a result of the activity of the Junior Company (B. C. & Yukon Chamber of Mines, 1977). In the Province of Ontario, one research study indicated that between 1951 and 1974 the 'Juniors' spent only 28 percent of the total exploration funds but were responsible for 62 percent of all economic discoveries (Freyman, 1978). The reasons for the success of the Juniors are tied to a variety of factors, the main one being personal initiative based on incentive. In other words, the principals, or their employees have 'a piece of the action.' The smaller companies can operate faster and more efficiently than their larger counterparts. The Junior Company is also destined to take some bigger risks, the 'long shots,' many of which efforts by virtue of the Junior's perseverance coupled with a touch of 'ore is where you find it' philosophy, result in major discoveries. The individuals, syndicates, private and publicly financed Junior Companies, because of high costs of exploration and development, cannot hope to finance most mineral prospects all the way to production. Exceptions do exist, those being the lower capital cost, small, high-grade deposits. Private investors and publicly financed Junior companies, therefore, can usually afford to finance most exploration through the initial drill-testing stage. The major resource company will enter a mining deal with a Junior Company usually by way of option or joint venture agreement, and will finance to production to earn an equity in the prospect or the Junior Company or both. The conventional lending institutions, banks and government agencies, will usually only participate through loaning a portion of capital

Jan 1, 1985

By J. Campbell

The negative pressure developed within a solidifying sphere of pure iron is investigated theoretically assuming an elastic-plastic model. The maximum hydrostatic tension attainable is shown to be an order of magnitude smaller than that required for the homogeneous muclealion of pores in the liquid cove, and four orders of magnilude smaller than that predicted from) a rigid shell model. It is well-known that liquids can withstand large hydrostatic tensile stresses, or negative pressures. The various experimental investigations of the tensile strengths (often called the fracture pressures) of liquids are reviewed by Dean,1 and the theoretical attempts at estimating fracture pressures are critically assessed by wakeshima.2 Using Fisher's3 quation, the fracture pressure of pure liquid iron is about -70,000 atm, which may be too large by as much as a factor of 4, but is certainly correct to within an order of magnitude.' In view of the great importance of the problem of the nucleation of shrinkage cavities in castings it is of interest to determine exactly what tensile stresses can exist in the residual liquid in a solidifying casting; it has often been assumed that, because of the very low strengths of solid metals near their melting points, no interior stresses are developed at all. Nussey4 has determined theoretically the pressure in the liquid core of a solidifying metal sphere assuming that the solidified shell does not deform (i .e., is perfectly rigid), so that because of the contraction accompanying solidification (a) (about 3 pct for most metals) the progressive deposition of solid onto the inner surface of the shell causes the remaining liquid to be expanded to make up this difference in volume. This leads to a relation between the pressure P in the liquid, the initial pressure, PO, the bulk modulus of the liquid, K, and the inner and outer radii of the solid shell, o and b, respectively:

Jan 1, 1968

By A. Vignes, J. P. Sabatier

A study of ternary diffusion at 1315°C in the Fe-Co-Ni system covering the entire ternary phase diagram has been carried out. Experimental values of the four interdiffusion coefficients DFeNico,DFeCoCo, DFeCoNi were computed at 33 points of the ternary diagram. The limiting values of these coefficients on the three sides of the ternary diizgram have also been determined. This set of data is presented as a contour map on the ternary isotherm for each of the four coefficients. Assuming that the Fe-Co-Ni system can be considered as ideal, the phenomenological coefficients Lk ij (with k = Fe) have been computed and the Onsager reciprocal relutions verified. It is shown that, in the Fe-Co-Ni system, the diffusion process can also be described by only two interdiffusion coefficients DFeFe and DCoNiFe, the second cross diffusion coefficient DCoFeNi being equal to zero and the second direct difusion coefficient being given by The values of the cross interdiffusion coefficients and of the Onsager coefficients are explained in terms of atomic mobilities of the three components with the help of a kinetic calculation due to Lane and Kirkaldy.8 It is shown that all the results are explained if the tracer difusion coefficients of the three components are such that DFe > DNi ~ DCo in complete agreement with experimental data on the three binary systems. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. In binary diffusion, there is just one independent composition variable and only one coefficient Dij is needed to describe the interdiffusion process. In ternary diffusion, we must allow for cross interaction between two independent species, and four interdiffusion coefficients are necessary to describe the transport process. Kirkaldy et al.1,2 have determined interdiffusion coefficients in the systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy4 have reported intrinsic diffusion coefficients for the r phase at 1300°C of Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.3 Interdiffusion coefficients were measured at three different compositions at 850°C in the single phase copper-rich corner of the Cu-Zn-Mn system by Dayananda and race.5 Zie-bold and Ogilvie6 have determined interdiffusion coefficients in the single-phase field of the Cu-Ag-Au system at 725°C. Preliminary results on diffusion at 1136°C in the system Fe-Co-Ni have been reported.7 In this study, data are reported on a more complete determination of interdiffusion coefficients in the Fe-Co-Ni system in the entire ternary at 1315°C. There is complete solid solubility with the fcc structures at 1315ºC, and this system can be considered as nearly ideal. This approximation allows the computation of the Onsager phenomenological coefficients. These values can then be used to test a kinetic calculation of the Onsager L coefficients in ternary substitutional solid solutions due to Lane and Kirkaldy.8

Jan 1, 1970

By Dr. O’Neil Thomas J., Donald W. Gentry

"We should be concerned about the future be- cause we will have to spend the rest of our lives there. " -Charles Kettering INTRODUCTION Since the early 1970s, there has been no economic phenomenon that has been more widely discussed or experienced in the United States than inflation. Al- though its precise definition and measurement are elusive, inflation has had pro- found and extensive impacts on the manner in which nearly everyone lives. It is painfully obvious to consumers that inflation is characterized by a continuing up- ward spiral of prices. In a capital-intensive industry like mining, those increases can be positively breathtaking. An interesting example is shown in Table 1. Table I shows that on a unit basis, the equivalent 1980 capital cost of Cuajone was over six times the cost of the adjacent and quite similar Toquepala operation completed in 1959. Such sobering statistics weigh heavily on the minds of executives who are contemplating major investments in new mining facilities. In spite of its monumental presence, inflation has usually been either inadequately covered or totally ignored in textbooks on engineering economy. The reasons for this are not entirely clear, but a contributing factor is the inherent difficulty in accurately predicting inflation. However, under certain conditions, inflation may become the most important factor in a mining investment, and it can rarely be safely ignored in capital investment analyses. DEFINING AND MEASURING INFLATION Defining inflation and related terms is relatively easy. Its measurement, how- ever, is the source of almost endless debate in economic and political circles. How- ever, much of that debate is not relevant to the scope of this book, so that only those issues which impact directly on the capital investment decision are covered in this section. Inflation is the general decline in the value of money as measured by what it will buy. It is clear, then, that the rate of inflation varies with the particular currency under consideration as well as the type of goods and services being purchased. One would find, for example, that the general rate of inflation relative to German marks

Jan 1, 1984

By S. S. Nosseir

INTRODUCTION General Quebec Cartier Mining Co. (QCM) , Canadian subsidiary of U . S. Steel Corporation, operates two iron ore concentrators at the North Shore of Quebec, Canada. In its own operation at Mount-Wright, over 45 million tons per year of crude ore are ground, fully autogenous in six 32' x 11-1/2 Dominion Engineering mills. At Fire Lake/Lac Jeannine operation, property of Sidbec Normines Incorporated (SNI), over 11 million tons per year of crude ore are now ground, fully autogenous, in twelve 18' x 5' Hardinge mills. The Lac Jeannine concentrator was originally constructed by Q.C.M. in 1960 and. was since operated, in beneficiating the Lac Jeannine ore deposit until fully depleted in 1977, at an annual capacity of 18 million tons of crude per year. In 1976, the new company, Sidbec Normines, was incorporated by Sidbec Corporation, British Steel Corporation and Quebec Cartier Mining Co., in proportional holding of approximately 51 to 41 to 8 percent respectively. Since the acquisition of the Fire Lake ore deposit and Jeannine concentrator by the new company, QCM has continued managing the mine and concentrator operaions for S idbec Normines Inc . Flow-Sheet Design Jeannine concentrator comprises twelve identical mill lines grinding the ROM from 8" top size to 14 mesh nominal size range. Driven by 600 H.P. motor at 13.4 RPM corresponding to 73% critical speed, each mill is operated in a closed circuit with two 5' x 12' vibrating screens dressed with 2.5 x 25 mm slot opening cloth. The ground product or screen undersize at an average grade of 33.4% Fe is beneficiated by gravity separation to produce 66.5% Fe concentrate grade at 42.7% weight recovery. At the rougher stage, each mill line con-tains 128 Humphrey 13- 1/2" pitch spirals which produce a final tailing, middling and concentrate products. The rougher concentrate - so produced - is classified by 64 Humphrey pocket sizers into an underflow, which is a final concentrate product and an overflow which is further upgraded by 64 cleaner spirals. The cleaner concentrate together with the pocket sizer 's underflow are dewatered on a 13'[6] horizontal filter. The rougher middling together with the cleaner tailing are recycled in a closed circuit with the spirals. The rougher tailing after dewatering by hydrocyclones is disposed of by a

Jan 1, 1982

By W. E. Pugh

The object of the following is to discuss a few of the problems encountered in the practical field application of reflection seismology. Very little has been published on this phase of the work and it is to be hoped that discussions will be presented by many seismologists who have met with these problems in the field. No attempt will be made to discuss the general principles of reflection prospecting, nor to outline the general field procedure. These phases have been presented more or less in detail in previous publications1 while economy of space and time prevents their being repeated or amended here. If, in the following pages, some criticism is offered of those who have already given their time and efforts to present valuable papers on reflection shooting, we trust that it will be accepted in the constructive light under which it is offered. We do not wish to give the impression that the following paragraphs represent ultimate achievement in field procedure; they are presented more to illustrate methods we have found satisfactory thus far. We believe that the following three subjects are inexorably linked with the continued future successes and more widespread use of the reflection method which, at the present time, is the most

Jan 1, 1934

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/1 6 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible. to maintain in stock marbles of the color, size, and thickness called for,, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill. such, orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By E. S. Machlin, Morris Cohen

GRENINGER and Troiano' were the first to establish the fact that the habit planes of mar-tensitic products are usually planes of high indices. In steels containing 0.55 to 1.4 pct C, the habit plane indices are {225}A.* In steels with more than 1.5 pct C and in Fe-Ni alloys, the indices are {259In. The presence of both habits in certain alloy steels has been reported recently." Several investigators"-" have subsequently attempted to provide an understanding of these complex habit relations. Bowles'6 work is the most recent and the most successful. Like Greninger and Troiano, Bowles concluded that the transformation occurs in two steps, the first, a strain (or displacement) that is homogeneous throughout the volume of the martensitic plate, while the second is a strain that is homogeneous only within relatively small portions of the martensitic plate. The first strain yields the measured tilt of the specimen surface, but does not produce the final martensitic structure. This and the correct lattice orientations are achieved by the second strain. Bowles also reasoned that each strain could be described by the motion of a plane of no rotation and no distortion (hereinafter called the invariant plane) in a direction not necessarily contained in the plane.** In applying these considerations to steels with {225}a habits, Bowles found that the habit plane coincided with the invariant plane of the first strain, a result which signified that the atoms move along certain paths during the transformation. Whether this correlation results from the existence of some sort of a plate nucleus6 lying along the invariant plane of the first strain, or whether the invariant plane primarily defines the preferred directions of propagation of the first strain, will be discussed in a later section. There are two obstacles to the general acceptance of Bowles' treatment: 1—it has not been shown that elements of his double-strain analysis are unique, and 2—it is not known whether his treatment applies to transformations yielding the {2591A habit. Unless these two questions are resolved, the correlation between the habit and invariant planes in the {225}A systems might be regarded as coincidental. Experimental Procedure Using a 70 pct Fe-30 pct Ni alloy as an example of a {2591A habit system, preliminary attempts were made to obtain a double-strain solution based on a Nishiyamax** set of orientation relations and on a Greninger-Troianot set, adopting the stereographic technique described by Bowles" who used the Kurd-jumow-Sachstt set in connection with the {225}A habit. These attempts were unsuccessful because the method is essentially one of trial and error and requires either exceedingly good luck or a prior knowledge of the results being sought. Consequently it was decided to measure independently the strain associated with the formation of a martensitic plate as well as the habit-plane indices of the particular plate. By means of matrix algebra, the measured strain was applied to the austenite lattice, whose orientation with respect to the strain was determined, in order to ascertain whether the resultant structure would have the lattice of martensite. This was not found to be the case, and hence it was assumed that the measured strain was the first of two Bowles-type strains, characterized by the motion of an invariant plane. A solution of this displacement was obtained in terms of the invariant-plane indices and the direction of motion of the atoms. Then the second strain

Jan 1, 1952

By R. T. DeHoff

A new approach to the measurement of the size distribution of particulate structures imbedded in opaque bodies is developed. The method is based upon the assumption of a general two-parameter distribution curve, and the estimation of these two parameters from three well-known counting measurements made upon metallogvaphic sections. The total number of particles in the system is also a product of the analysis. Application of the method with the assumption of the logarithmiconorma1 disfribution function is developed in detail. A complete description of the geometry of a particulate structure requires the determination of the size distribution of particles. The problem of estimating the size distribution of particles of a particular phase in a multiphase system, or the grain-size distribution in a homogeneous system, has been approached by many investigators.'-'0 All of the solutions proposed by these investigators share the following characteristics. a) A minimum of several hundred particle sections in the microstructure must be examined, and some characteristic dimension recorded, such as area,3'5 intercept length,6"9 or diameter.1'2'4'10 b) The resulting data must undergo a series of fairly complex calculations to generate the empirical histogram which describes the size distribution in three dimensions. c) In order to manipulate the result, the histogram must be fitted to some assumed mathematical formula, using the attendant statistical procedures. d) With two notable exceptions,8,10 the particles must be spherical. The measurements and calculations involved are in general very tedious and time-consuming, with the logical result that much effort has been expended in the development of equipment which will perform these tasks automatically and semiautomati-cally.9,11-15 considerable success has been achieved in this area, but the equipment is in general expensive, and usually places stringent requirements On the quality of microstructure which can be reliably analyzed. In laboratories which do not possess such equip- ment, the analysis of geometry is usually limited to measuring total properties of the microstructures, such as volume fraction and interfacial area, because the measurements required are much simpler to make. The determination of size distributions rarely is undertaken. The development which is presented in this paper permits the estimation of size distributions of three-dimensional structures from the same simple counting measurements which are required to determine the surface area and volume fraction of the particulate structure, and one other counting measurement. The basic approach that is used is to assume a general mathematical form for the distribution, which is described by two parameters (as the normal distribution is described by assigning values to the mean and the standard deviation), and then estimate these two parameters from the results of the counting measurements. The introduction of a third counting measurement also permits the evaluation of the number of particles per unit volume, Nv.

Jan 1, 1965

By B. L. Landrum, J. Simmons, J. M. Pinson, P. B. Crawford

Patentiometric model data have been obtained to estimate the effect of vertical fractures on the areas swept after breakthrough in water flooding and miscible displacement programs such as gas cycling where the mobility is near one, The data are presented for the case of the fire-spot pattern in which the cemer well is fractured various lengths and orientations, the data indicate that for 10-acre spacing, fractures extetidirrg over 1300 ft in either directior1 from the fractured well may re.srrlt in reductions in sweep efficiencics from 72 to approximately 34 per cent. However. the area swept after break through may be quite largr and only 10 or 12 per cent 1ess than would be obtained if the reservoir were trot fractured. For the specific case when the volume of fluid injected is equivalent to 100 per cent of the pattern vol-unie, the swent area may vary from 80 to 88 per cent, depending on the lenght of the fracture. The former value is that which occurs when the break through or sweep efficiency was orrly 34 per cent and the latter figrrre of 88 per cent is that which is obtained if the reservoir were unfrac-ttm'd. It is pointed out that although the sweep efficiency may he very low in vertically fractured five-spot patterrz.s, the area swept at low water-oil ratios may be only 5 to 10 per cent less than those achieved if the reservoir were unfractured. INTRODUCTION Since the initiation of commercial reservoir fracturing techniques it has been desirable to determine the effect of fractures on the areas swept after breakthrough. Most water flooding or gas cycling projects are continued for substantial periods after the brcakthrough of the injected fluid. Although the sweep efficiency serves as one criterion for rating various flooding patterns. the area swept after breakthrough for various water-oil ratios or percentage wet gas, if cycling. is of perhaps more importance than the sweep efficiency alone. Sweep efficiency data on the vertically fractured five-spot have been presented3. Previous work on the line-drive pattern has shown the effect of vertical fractures on the area swept after breakthrough for the case in which the distance between injection and producing wells divided by the distance between adjacent input wells was equivalent to 1.5 (see lief. 2). The data indicated that for the line-drive pattern it may be desirable to flood or cycle substantially perpendicular to the fractures in order to achieve the greatest recovery for the smallest volume of fluid injected. For this study the center well of a five-spot is assumed as the fractured well. All fractures were assumed to originate at this well and extend into the reservoir for various distances and orientations. All the fractures are straight and are of large permeability compared to the matrix proper. These data are presented to aid the engineer in estimating fractured five-spot pattern performance. ANALOGY The potentiometric model was used in making this study. The model used was 20 20 in. by approximately 1-in. deep. For certain portions of the study one corner of this model was considered to be an injection well and the opposite corner a production well. To simulate vertical fractures a copper sheet was soldered to the wire well and made to conform to the desired length and orientation. In other studies the same model was used except that the four corners of the model might be considered as the corner wells of a five-spot pattern and a fifth well was placed in the center of the model. The well placed in the center of the model was fractured. The total fracture length is L and the well spacing. d. The complimentary fracture angles will be obvious from Figs. 3 and 4. The data obtained on the potentio-metric model assumes the pay to be uniform and homogeneous, the mobility ratio is one, steady-state conditions exist and gravity effects arc neglected. The permeability of the fractures is very great compared to that of the matrix proper. The po-tentiometric model has been used widely both in water flooding and gas cycling projects, and may be used for miscible displacement; how-ever. it is believed that the poten-tiometric model data are more properly applicable to gas cycling than water flooding because the model as-

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. Temperatures and Underground Waters Surface Temperatures.—The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the downcast shafts; however, the variation between winter and summer causes a difference of only 2" to 3" in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.—Rock temperatures on the deeper levels of the mine are as follows:

Jan 1, 1940

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. Temperatures and Underground Waters Surface Temperatures.—The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the downcast shafts; however, the variation between winter and summer causes a difference of only 2" to 3" in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.—Rock temperatures on the deeper levels of the mine are as follows:

Jan 1, 1940

By S. H. Ash

Diesel locomotives, trucks, bulldozers, and other diesel-powered equipment are fast proving their superiority for mine transportation purposes. MORE than 100 minerals are mined and processed in the U. S. Management and labor have negotiated wage-scale agreements that have balanced wages and affected cost of labor in such a manner that comparisons can be made of transportation costs. Transportation of materials underground has become of vital importance.1"0 This report describes underground haulage methods and equipment, presents cost analyses, and discusses future plans for underground transportation in metal mines. It does not cover hoisting in shafts or slopes by cage, skip, or cars. Advancements have been made by the metal mining industry in lowering transportation costs in several mines, making it possible to mine orebodies or portions of orebodies not considered economically recoverable a few years ago.7,8 Wumerous reports have been written on transportation at metal mines; this report covers recent haulage at some representative mines throughout the U. S. The term metal mine is used to include all noncoal mines from which up-to-date information was obtainable. The best haulage equipment is subject to break- downs and accidents; but unless the rolling equipment, track, and signal systems are kept in good repair and are operated systematically, these breakdowns and accidents are likely to be frequent, destructive, and more costly than are necessary.10 Rail haulage crews using dependable rolling stock can move trips safely over grades low enough to be traveled without loss of control; this applies particularly if the track is straight and well maintained. Few accidents occur on main haulage lines if visibility and clearance are good and clear track is assured. One-way traffic underground is a recent development contributing to reduction of accidents and increased efficiency in mine haulage (Kelly mine, Anaconda Co., Butte, Mont., and Climax mine, Climax Molybdenum Co., Climax, Colo.)." Locomotives: Six types of mine locomotive used in recent years are trolley, storage battery, combination trolley and storage battery, diesel, compressed air, and gasoline. Electric haulage has been displaced by compressed air locomotives, which have been used successfully in certain instances, especially on dirty and wet tracks and steep grades." Maintenance cost is high, and operating efficiency, from a power standpoint, is low. Compressed air locomotives operate under self-contained power, and the absence of bare elec-

Jan 1, 1957

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y' alloys by gas quenching, is extensively ordered prior to y' (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y', Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y'. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y', or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.' The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.' An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By A. M. Gaudin

UNTIL recently little attention has been paid to the effect of particle size on flotation. This has been especially true of material finer than 200 mesh.1 Particles of different sizes must behave differently in a flotation circuit; increased information along this line would be of practical use as well as of theoretical interest. The object of this study has been to determine what effect particle size has on floatability. The problem has been approached in two ways. One method consisted in a study of samples of the final products of several mills. These samples were sized and each size-product was analyzed for its important constituents. Bakelite briquettes2 of some of the products were made and studied under the microscope. This investigation is being continued, with particular reference to quantitative microscopic analysis of intermediate products of flotation plants. M In the other method of study, mixtures of pure minerals were ground to different degrees of fineness and floated. The products were then sized and analyzed. A study of the behavior of mixtures of pure sized minerals would have been illuminating, but after trial it was considered impractical on account of the tediousness of the large amount of elutriation required and the fact that the mineral particles would oxidize while being sized, preparatory to flotation. Broadly speaking, the following conclusions have been reached: 1. Results obtained by the two methods of study are in agreement. 2. The usual notion about the relative ease of flotation of very fine particles does not agree with the facts: 3. There is a time sequence of flotation with regard to particle size, the medium coarse particles floating first. 4. No successful method of floating extremely fine pulps has been found. 5. Recovery is optimum in a certain well-defined size range. 6. Selection is optimum in another well-defined size range.

Jan 1, 1931

By A. R. Kinkel

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)—Mr. Kinkel's article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel's conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel's nomenclature being used. The first member, which Mr. Kinkel terms the upper unit of the Balaklala rhyolite, consists of a single, massive, homogenous body of very silicious igneous rock, consisting almost wholly of quartz and albite, and averaging about 80 pct silica. Most geologists of the U. S. Geological Survey who have previously inspected the district have called it an alaskite. It is not a pile of several members, but is a single unit, without internal subdivisions. It has the form of a recumbent lens, approximately flat on the bottom and arched on top, several miles in diameter, and attaining a maximum thickness of 1000 to 1200 ft. It varies in texture from porphyritic to holocrystalline, and contains unusually large quartz phenocrysts up to 4 mm diam. Mr. Kinkel considers this formation to be a thick lava flow that is older than the overlying Kennett shale, while the writers interpret it as being intrusive, constituting a domed sill or laccolith that is younger than the Kennett shale. Their reasons are as follows: 1) This formation shows none of the features which within the writers' experience invariably accompany very silicious lava flows. Nowhere is it vesicular; nowhere does it contain any glass or its devitrified equivalent; nowhere does it contain flow breccia; and nowhere has it a ragged top, in spite of the fact that there is no evidence of surface erosion, which might have removed such a top.

Jan 1, 1957

By Gerald Edmunds

In a paper1 before this Institute in 1940, the writer reported that the surface orientation texture of zinc and cadmium differed from the texture existing within the casting, in that basal planes were parallel to the surface. He was unable to rationalize the , origin of this surface texture. It is conceivable that the surface orientation texture is influenced by the atomic force fields, which are different at the surface and within the body of metal. It was considered that a radical changc in the surface against which the metal is cast might alter the surface texture. In trial of this, zinc has been cast against a surface of molten lead, but the same result has been obtained—i.e., (001) parallel, ± 2oo, to the surface—as was obtained when it was cast against air, Transite or iron.' Into the bottom of an open cast-iron tray, 7 by 14 in. by 2 in. deep, preheated to about 275°C., about 1/4 in. of lead, then 1/2 in. of zinc was poured, and the whole was covered with an electric heater to enforce freezing from the bottom upward. After a lapse of time sufficient for the zinc but not the lead to solidify, the zinc slab was raised free of the molten lead. The bottom surface of the zinc casting was coated with a thin layer of lead. A specimen of the slab 136 in. square was metallographically polished to flatten it and remove the slight film of lead, and the orientation was determined by the method used before,' with the result stated above. Some determinations have also been made on other metals, as follows: Surface orientation determinations were made on the 3/8-in. diameter grip section of two 1/4-in. diameter aluminum-alloy die-cast tensile bars and on a 1/8 by 1/2-in. flat aluminum-alloy die-cast tensile bar. None of these three aluminum die castings exhibited any preferred orientation at the surface. A brass die casting (nominal composition: 60 Cu, 37.75 Zn, 1.00 Sn, 1.00 Pb, 0.10 Al, 0.15 Si) furnished by C. S. Smith was also examined. The surface showed a random orientation of alpha and beta. Summary A zinc casting solidified against a molten lead surface was found to have the same surface orientation texture, (001) parallel to the surface, as other zinc and cadmium castings. Aluminum and alpha-beta brass die castings were found to have random grain orientation textures at the surface. Acknowledgment The X-ray determinations were conducted by M. L. Fuller.

Jan 1, 1945