Search Documents

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By R. S. Archibald

THE Blueberry mine is about 10 miles west of Ishpeming, Marquette County, Michigan. The property consists of about 2000 acres in sets. 3, 4 and 5, T. 47, N.R. 28W. and sets. 32, 33 and 34, T. 48, N.R. 28W., and, excepting one intervening 80-acre tract, contains the iron formation for a length of about 2 1/4 miles. The property is traversed by State Highway M-28 and is served by three railways, the Chicago & Northwestern, the Duluth, South Shore & Atlantic, and the Lake Superior & Ishpeming. The Northwestern transports the ore to a dock at Escanaba; the other railways, to Mar¬quette. Ore for Chicago goes via Escanaba and that for Lower Lake ports, as Detroit, Cleveland, and Buffalo, via Marquette.

Jan 1, 1935

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal's investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid's principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner's equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

By Richard L. Stowe

Four NX-diameter holes were diamond-drilled in competent granite. Samples of the recovered core were used in laboratory tests. A borehole, plate-bearing device known as a Goodman jack was used to perform load deformation tests on the rock in the core hole. The majority of samples used in the laboratory tests were taken from depths in the hole at or within 5 ft of those at which the plate bearing tests were made. Borehole camera records, compressional and shear wave velocities, and densities were measured. Dynamic elastic constants were computed for the in-situ material, while comparative data (except camera records) were obtained in the laboratory. These data were examined to evaluate the significance of the in-situ modulus of deformation (Ed), the value computed from Goodman jack tests. Average test results show an excellent correlation between in-situ and laboratory data. The ratio of laboratory to field deformation modulus ranges from 9.82 to 7.21 for 3,000 and 9,000-psi stress levels, respectively. The dynamic modulus ratio, ED field/Ep lab, is 1.02; the compressional wave velocity ratio, V8 field/V8 lab, is 0.94; the shear wave velocity ratio, V, field/V, lab, is 1.12; and the density ratio, field [y/y] lab, is 0.95.

Jan 1, 1973

By D. D. Dunkin

Sandstone has been prepared for glassmaking purposes, and marketed from the White River Valley in Arkansas at Guion, Izard County, since about 1910—soon after the completion of the White River Branch of the Missouri Pacific R. R. Co. Until 1921, operations were somewhat spasmodic and ended in many failures. In that year a plant was built by the Silica Products Co., Inc., and since that time the operation has been continuous and steady. The land is held under leases, covering about 30 square miles of the best sandstone adjacent to the railroad. Most of the product is shipped to glassmakers. Geology The St. Peter sandstone is rather widely distributed in north central Arkansas and is exposed most prominently in outcrops along the slopes of the White River Valley and its tributarirs that form the division between the Boston Mountains to the south and the Salem Plateau of the Ozarks to the north. It is of Ordovician age and is generally underlaid by Cotter dolomite and capped by Plattin limestone, except in the vicinity of Bellefonte and Everton. At those places, it is a massive cross-bedded, laminated, saccharoidal sandstone; underlying it is the Everton limestone and overlying it, the Joachim magnesium limestone The sandstone at Everton contains numerous phosphatic pebbles and inclusions of sandy limestone. The irregularity of cross-section, the evidence of sorting action and the phosphatic pebbles appear to be indications of secondary deposition The St. Peter sandstone occurs as a massive formation in the picturesque bluffs along the White River Valley from near the eastern escarprnent of the uplift northwestmard into the Ozarks. The exposure shows a series of gentle anticlinal and synclinal folds. The greatest thickness is at the southeastern end, where it is over 100 ft. in many places. It thins out to the north and west and then to isolated and scattered deposits which cap the ridges and mountains of the Ozarks.

Jan 1, 1928

By W. Myron Davy

For more than a decade the use of the metallographic microscope, by mining geologists, for examining ores has been increasing and conclusions founded upon examinations made by it are found in several recent professional papers of the United States Geological Survey as well as in our technical publications. But most mining men have been slow to realize the positive value of this instrument in their daily work. The reason for this condition is not hard to find. The varied applications, the simplicity of preparation, and the methods of studying a polished section of ore have not been widely published. Papers in technical periodicals have been profusely illustrated by photographs of such sections, special refined methods of procedure for laboratory work have been described, and complete and detailed schemes of identifying the ore minerals have been published in book form.1 But simple and easily applied directions and, what, is more important, light, compact, and inexpensive equipment have not been available. The simplest microscope obtainable is intended for laboratory use and is much too bulky for the average field equipment; at present it costs about one hundred dollars for the instrument alone. Methods previously described for polishing specimens have necessitated electrically driven lap wheels, which are found only in permanent installations. It is small wonder that the examining mining engineer, field geologist, resident engineers, and mill men have looked upon the subject as being too involved for the field and have assigned it to the laboratory investigator. The writer has been interested in this question for some time from the viewpoint of his own work. Being handicapped by the difficulties enumerated, he has designed an outfit that has proved very useful. It is described here and its. applications shown in the hope that it may be of equal value to others, and that a start will be made toward popularizing

Jan 8, 1920

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By Kenneth K. Humphreys, F. R. Zachar, A. G. Gilbert

INTRODUCTION by F. R. ZACHAR and A. G. GILBERT Coal producers are not only faced with the problems of mining coal, but must also decide to what extent they can invest capital and what operating and maintenance expense they can afford, after mining, to market their product in sufficient volume and at a reasonable profit. Regardless of whether the operator is contemplating a new operation or merely considering expanding present facilities, market requirements, ability to make a product meeting requirements, probable costs and possible future changes in raw coal or finished product must be considered. In addition, such items as flow sheet, structural designs, storage facilities, etc, must be examined individually and collectively. In estimating preparation costs to meet predetermined market specifications, the operator must calculate the economics of present preparation practices to anticipate the increase to total production which results when the quality of the finished product is increased. The consumers of coal are continually seeking to obtain the best and most adaptable product for their money. Regardless of whether coal is used for coking, industrial requirements, electric power generation, domestic fuel or for other purposes, it will be scrutinized from such standpoints as delivered cost, suitability for utilization in certain equipment, ease of ash disposal, adaptability to material handling system plans and its potential for generating dust problems. Utilities, due to large capacity volume requirements, are generally in a position to select coal that will result in the lowest over-all cost per million Btu. Freight costs, paid by the utility, are important and are given utmost consideration when a coal is under consideration. Steel companies, whether producing or purchasing coking coal, are continually seeking coal that will result in lowering the cost of pig iron production. Since it is usually necessary to clean to lower specific gravities, say 1.40, to turn out a product meeting metallurgical requirements, it follows that a high ash "middling" product is created. These low quality middlings do not command a good price. Therefore, unless the metallurgical coal can command sufficient realization to carry or subsidize the middlings, the operator may be ahead economically to prepare steam coal at a higher specific gravity. While the "unit-train" rate reductions have been helpful to the economy of the coal industry, the establishment of these rates has made mandatory the installation of storage and rapid car loading facilities at mines and plants shipping utility coal (see Chapter 15). A study of the economics

Jan 1, 1968

By R. M. Hudson

The removal of nitrogen from a nitrogenized low-carbon sheet steel that contained 0.011 wt pct N was determined during heat treatment in Hz-N, mixtures. TIze process followed a first-order rate law; that is, plots of the logarithm of nitrogen content in steel were linear with the time of treatment at a given temperature. The rate of removal increased with an increase in temperature from 900" to 1300°F. By 1400°F the rate in dry hydrogen had decreased to a value intermediate between the rates at 1200" and at 1300°F; in wet (2.47 vol pct water vapor) hydrogen the rate at 1400°F was less than the rate at 1300°F and nearly the same as the rate at 1200OF. The rate at a given temperature increased as the 3/2 power of hydrogen concentration in the atmosphere. While wet atmosplzeres were generally more effective than the corresponding dry atmosplzeres, the effect of water vapor was much less pronounced than the influence of hydrogen content. NITROGEN is the principal agent in the strain aging of ferrite, the effect of carbon being secondary.' To eliminate the return of the yield point after straining and aging, it is claimed2 that the amount of nitrogen in solution in steel must be reduced to 0.0002 wt pct. Strong nitride-forming elements (titanium, vanadium, zirconium, and aluminum) can act to eliminate strain aging by combining with nitrogen. It is extremely difficult to decrease the nitrogen content in commercial steels to the low level required by conventional coil annealing because of the poor contact between the strip surface and the reactive atmosphere. However, a variety of gas-metal reactions can be effected by use of the open-coil annealing method,3 in which the metal surface is fully exposed to the atmosphere. With this possibility in mind, the Applied Research Laboratory has studied the influence of time, temperature, and atmosphere composition on the removal of nitrogen from low-carbon sheet steel. MATERIALS AND EXPERIMENTAL WORK Samples from a commercial nitrogenized low-carbon steel (0.010 in. thick) in the cold-reduced condition were used. The chemical composition of this steel is given in Table I. The gas mixtures used are listed in Table 11. The moisture content in the "wet" annealing atmospheres was controlled at a +70°F dew point (2.47 vol pct water vapor) by passing the gas mixture through a glass tube packed with a solid mixture of 10 pct anhydrous oxalic acid and 90 pct oxalic acid dihydrate held at 127°F; this technique has been described previously.4 For "dry" atmospheres, the gas mixtures were passed through a cold trap immersed in liquid nitrogen. A hinged-top Hevi-Duty electric furnace was used with a Vycor-glass furnace tube. When the furnace was at the desired temperature, the gas mixture was passed through the furnace at a flow rate between 1.1 and 1.2 cfh; coupons (size 3 by 3/4 in.) of the steel were pulled into the center of the Vycor-glass

Jan 1, 1964

By A. Phillips, H. J. Fisher

The influence of temperature and composition on the viscosity of high-purity liquid metals and alloys of the Pb-Sn and Sb-Cd systems was investigated by the logarithmic-decrement method. The variation of viscosity with temperature above the liquidus followed the equation: n = AeE/RT No large increase in viscosity was found just before normal freezing of any of the metals or alloys investigated. Certain alloys, supercooled below their stable liquidus, however, did show a marked increase in viscosity. Experimental activation energies for viscosity were determined for the metals investigated. Liquid-metal density values were obtained by a modified Joeger's method. IK an investigation of the properties of molten metals, the study of viscosity as a suitable means for studying the physical nature of the metallic liquid state has been utilized. Although interest in the relationship of the liquid to the solid-metal state holds promise of broadening the knowledge of metals in general, much information that is available regarding the influence of temperature and composition on viscosity, especially near the freezing point, is still controversial. The purpose of this paper is to present the results of recent work on this subject. Although interest in factors influencing the fluid behavior of metals and alloys has arisen from theoretical as well as applied studies of liquid-metal properties, the development of a comprehensive theory of the mechanism of viscosity has been handicapped because so little is known about the liquid state. Several theories of viscosity have been proposed and among the more recent are those of Andrade,1 Bernal,2 Frenkel,3 Eyring,4 and Gutmann and Simmons.5 Athough these contributions have helped to establish a basis of approach for studying the nature of viscosity, the fundamental aspects of the variation of viscosity with alloy composition have, in general, been neglected. Experimental Metals and Alloys Investigated: The Pb-Sn and Sb-Cd alloy systems were selected for investigation because they form constitutional features of theo-

Jan 1, 1955

By Donald F. Irwin

Amid the violent economic changes of recent years that have affected Canadian gold-mining operations so deeply, the discovery and early developments of Kirkland Lake might easily be overlooked. There was more than one "false dawn" for the district before developments finally established the fact of a superb mineralized zone extending through the present operating properties. Never far from the railway, Kirkland Lake has had the benefit of direct rail service for many years. The pioneer discovery on which the first mill and cyanide plant was erected was the "Tough-Oakes," this property being on what is now the eastern end of the producing area; some time later, the "Lake Shore" was discovered at the present center of the district, and a small plant was built upon it also. Both of these early treatment plants were of pre-war design. Progress in gold metallurgy has caused a gradual change in cyanide practice since the early days at Kirkland Lake, which may be observed in the various plants now operating there. From the beginning, it was recognized that Kirkland Lake ores were more responsive to cyanidation than to alternative recovery methods, and that their mineralization contained gold in very finely divided form. Although sulfides and tellurides are present, the quantity is small, being in the order of 1 or 2 per cent by weight, so that gravity concentration is undesirable, since gold is not confined to the sulfides. Some complication is offered by the presence of tellurides, which have caused lengthy controversy over their importance in recovery methods, but which are now generally regarded as less harmful in the light of increasingly high recoveries being obtained. Nevertheless, finely divided gold intimately associated with sulfides in the presence of tellurides; and occurring in the hard Kirkland Lake porphyry ore, substantially free from natural slime-forming constituents, indicates fine grinding. This has been the universal practice although the degree of grinding has varied a little among the different mills and is considerably finer now than formerly. The natural condition as outlined caused the establishment of fine grinding at an early stage in the development of Kirkland Lake, during the period of valuation of gold at, $20.67 per ounce. With the arrival

Jan 1, 1935

By Donald Ofte, L. J. Wittenberg

The absolute viscosity coefficients and activation energies for viscous flow of bismuth, lead, and zinc are reported. The viscosities were measured in an oscillating cup viscosimeter from nearly 1000°C to within 1 deg of the melting point of zinc; 2 deg of the melting point of lead; and in the supercooled condition of bismuth, 9 deg below the melting point. Two methods of relating the change in the viscosity coeflicient with temperature were compared. From the plot of the logarithm of viscosity (77) as a function of reciprocal absolute temperature (1/T), the equations of the lines which fit the data are: AS a part of the Reactor Fuels and Materials Research program at Mound Laboratory, precise measurements of the physical properties of liquid metals are of interest because the desirability for a low vapor pressure liquid coolant in high-temperature nuclear power plants has focused attention on the properties of the liquid metals.' Also, a clearer understanding of the liquid metal state can be achieved when better measurements are available. For these reasons, the viscosity values of certain liquid metals have been determined. The viscosities of the liquid metals, bismuth, lead, and zinc are measured in an oscillating cup viscosi-meter. In this apparatus the liquid is sealed in a right-circular cylindrical cup which is attached to a torsion fiber so that the system forms a torsion pendulum. The damping effect of the molten metal upon the normal oscillations of the torsion pendulum is a function of the viscosity of the liquid. This method is advantageous because of the small amount of sample required (8 to 10 cc), the ease of remote operation of the apparatus in a vacuum system, and the containment of the liquid metal in a hermetically sealed, nonreactive, tantalum crucible. With the liquid metal sealed in the crucible, loss of liquid by vaporization and chemical reactions with atmospheric gases are prevented. Additionally, an absolute viscosity determination is obtained which avoids the sources of possible error in a relative measurement. The difficulties in a relative method include the repetitious cup calibrations, and the uncertainty inherent in the practice of calibration of the apparatus at room temperature and extrapolation to the high temperatures necessary for the investigation of most liquid metals. The oscillating cup viscosimeter was first described by Meyer in 1891.2 The first complete mathematical treatment offering an absolute measurement of viscosity with this type of apparatus was proposed by Andrade and chiong3 in 1936 for an oscillating sphere filled with a liquid. This solution was modified to include a right circular cylinder by Hopkins and Toye4 in 1950, and R. Roscoe5 in 1958. Roscoe's treatment for the calculation of the viscosity of a liquid at a particular temperature from the logarithmic decrement and period of oscillation of the torsion pendulum was used in this investigation. A detailed description of the method of calculating the viscosity from these measurements has been reported earlier.' This calculation has been programmed for the IBM 704 and IBM 1620 computers for expedition of the otherwise laborious calculations. APPARATUS The cutaway view of the apparatus in Fig. 1 shows the suspension system within the high vacuum enclosure. The low residual gas pressure. maintained between 1 x 10-4 and 5 X 10-6 mm Hg during a determination, avoided both air drag on the pendulum and

Jan 1, 1963

By Heinrich Ries

With the rapid development of Canadian industries calling for the use of fire-brick for the lining of furnaces or cement-kilns, for constructing brick-kilns or coke-ovens, for lead-furnaces, etc., the question has often arisen whether the provirices within the Dominion have not the necessary raw materials for the manufacture of such refractory wares. As an indication for the need of such products in Canada, me find that the imports in 1910 amounted in value to $519,454. The materials came in part from Great Britain, and part from the United States. Those supplied by the latter country are obtained largely from Pennsylvania and Ohio, and when shipped to distant points, such as British Columbia, the item of transportation is a serious factor. Scotch fire-brick is used both in eastern and western Canada, but in the latter case the shipments are made by water route to Vancouver. During the past four years I have been investigating the clay-deposits of Canada, for the Canadian Geological Survey, and while all types of clay have been included in the study, special pains have been taken to ascertain the occurrence of refractory clays. As a result of this work we are able to report on the existence of beds of refractory clays at the followiug localities: Inverness and Shubenacadie, Nova Scotia; St. Remi, d'Amherst, Quebec; Dirt Hills and Cypress Hills, Saskatchewan; Sumas Mountain, near Clayburn, B. C., and Kyuquot, on northwestern Vancouver Island. A map of Canada, showing the fire-clay deposits, is given in Fig. 1. It is possible that other deposits may be discovered in the future in districts remotely located from the present lines of railroad.

Jan 1, 1914

By Wilbur H. Somerton

In order to evaluate the quantitative determination of porosity by various neutron logging systems, four test wells were constructed to simulate some of the possible variab1e.r found in field logging conditions. All of the test holes contain sections of limestone with one section of sandstone included in one well. Each well has a representative section of high, medium, and low porosity. Three borehole sizes are represented by three of the test wells, all containing fresh water. One test well contains saturated brine. Statistical and tune constant checks are made for each system evaluated. Runs and repeat runs are made with the sonde centered and eccentric. Factors evaluated are the effect of borehole size, sonde position, salinity, chemical composition of rock, and statistical variation. A semi-quantitative method of evaluation of these effects is used giving the average maximum per cent error possible for each. Drift and calibration procedures are also discussed. The effect of the various factors appears to be largely a function of the phenomena detected as well as the means of detection. Graphic illustrations of some of these effects are presented. It is concluded, that for accurate log interpretation, the hole size and sonde position should be known. INTRODUCTION The use of neutron logs for the derivation of porosity has become an accepted practice in many areas. In recent years, many different neutron logging systems have been offered to the industry. The neutron sources presently available are of the radium-beryllium or polonium -beryllium type. Detector types used are ionization chambers, Geiger-Mueller-type counters, proportional counters, or scintillation detectors used to detect or measure gamma rays, thermal neutrons, epithermal neutrons, fast neutrons or combinations of these. It is well-known that all systems do not respond alike in all environments. As a result, testing facilities and an evaluation method were developed for use in evaluating the porosity discriminating ability of neutron logging systems using conditions simulating those normally encountered in the field. With such an evaluation, the suitability of a logging system can be determined lor selected field conditions. TEST FACILITIES The testing facilities consist of wells containing rocks of various porosities, constructed to include as many parameters as practicable. Three pits were drilled to a depth of 20 ft and the fourth to a depth of 9 ft, all having 48-in. diameters. Rat holes were dug to a depth of 6 ft in the center of each pit and fitted with sections of pipe having appropriate diameters. The top of this pipe was located approximately 8 in. above the pit bottom. A 6-in, layer of cement was then poured on the bottom and while still wet, 42-in. OD corrugated, galvanized culvert pipe was set on bottom and centered in place. This pipe extends approximately 1 ft above the surface of the ground. The annulus around the culvert pipe was then filled with cement to the top. A 1- or 2-in. layer of sand was placed on the cement bottom to provide an adjustable bed on which to place the series of rocks set in each hole. A cross section of a typical test well containing the porous rocks is shown in Fig. 1.

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By C. E. Lundin

The Ce-H system was investigated in the temperature range, 573° to 1023°K, and the pressure range, 10-3 to 630 Torr, as a function of 'composition up to 72 at. pct H. Families of isothermal arid isopleth curves were plotted from the pressure-terr~perature-composition relationships. From these curves the solubility relationships were determined for the system. The isopleths are analytically represented by equilibrium dissociation pressure equations. The relative partial molal enthalpzes and entropies of solution of hydvogen in the systerrz were calculated fronz the dissociation pressure equulions and are tabulated. The integral free energies, enthalpies, and entropies of mixing in the Ce-H system were determined from the relative partial quantities and are also tabulated. The standard free energy, enthelpy, and entvopy of reaction of the dihydride phase at kcal per kcal per mole H2, and ?S° = -34. 1 cal per deg mole H2, respectively. The equilibrium dissociation pressure equation in the two-phase region is: UNTIL recently very little was known of the detailed solubility and thermodynamic relationships of the Ce-H system. Two previous investigations1,2 are noteworthy. However, significant discrepancies and omissions exist on analyzing them. The work of Mulford and Holley1 on cerium did not clearly delineate the boundaries of the two-phase region, Cess - CeH2-x. The plateau partial pressures were not thoroughly defined and were considerably displaced in pressure compared to those from the work of Warf and Korst.2 These latter authors concentrated their studies primarily from 823° to 1023°K in the pressure range of 1 to 760 Torr. No data were determined to outline the regions of primary solid solubility and the hydride phase. Also the establishment of the plateau partial pressures was rather limited in scope. In neither work was a treatment conducted of the relative partial molal enthalpies and entropies of solution of hydrogen in the single-phase regions and the integral thermodynamic quantities of mixing throughout the system. Therefore, it was the objective of this research to determine the complete equilibrium solubility relationships and thermodynamic data for the system by pressure-temperature-composition studies. EXPERIMENTAL PROCEDURE The cerium metal for this study was donated by the Reno Metallurgy Research Center of the Bureau of Mines. Total impurity content was 0.13 pct with only 60 ppm O. The metal was checked metallographically and contained only minor amounts of second phase compared to cerium from other sources. Specimen preparation was done in a dry box flushed with argon gas. The surface of a small rectangular piece of cerium (about 0.2 g) was filed with a clean, mill file. Final weighing was done in a tared enclosed vial containing argon gas. The specimen was then loaded quickly into the reaction chamber which was purged several times with high-purity hydrogen gas and then allowed to pump to about 10-6 Torr. The furnace was heated to the reaction temperature and the run started. The equipment used to conduct the hydriding was a Sievert's-type apparatus. Basically it consisted of a source for pure hydrogen, a precision gas-measuring burette, a heated reaction chamber, a McLeod gage, and a mercury manometer. Pure hydrogen was supplied by the thermal decomposition of uranium hydride. The 100-ml precision gas burette was graduated to 0.1-ml divisions and was used to measure the quantity of gas and admit it to the chamber. The reaction chamber was a quartz tube. Prior to each run, the cerium specimen was wrapped in a tungsten foil capsule to prevent reaction of the cerium with the quartz. Control of the temperature was achieved within ±1°K. Pressures in the manometer range were measured to ±0.5 Torr and in the McLeod range (10-3 to 5 Torr) to ±3 pct. The compositions of hydrogen in cerium were calculated in terms of hydrogen to cerium atomic ratio. These compositions were estimated to be ±0.01 H/Ce ratio. The technique used to study the equilibrium pressure-temperature-composition relationships of the Ce-H system was to develop experimentally a family of isothermal curves of composition vs pressure. The range of pressure through which each isotherm was developed was from 10-9 to about 630 Torr in the temperature interval, 573° to 1023°K. RESULTS AND DISCUSSION The hydriding characteristics of cerium are iso-morphous with those of the elements of the light-rare-earth group (lanthanum, cerium, praseodymium, and neodymium) wherein the region from the dihydride to trihydride is continuously single phase.' The structure of this phase is fcc.3 The heavy rare earths form a trihydride,2 which is hcp, separated by a two-phase region from the fcc dihydride phase. The Ce-H system is represented by the family of experimental isotherms in Fig. 1. Due to the small scale required to draw the curves, the experimental points are omitted; however, a total of 240 experimental data points were taken to prepare these curves. The solubility relationships can be deduced therefrom. Three distinct regions of partial pressure and composition can be seen. The region of cerium solid solution is represented by the rapidly rising isotherms in the dilute composition range. In accordance with Gibbs Phase Rule only one solid phase, the cerium solid so-

Jan 1, 1967

By Dr. O’Neil Thomas J., Donald W. Gentry

"We can easily represent things as we wish them to be..” -Aesop INTRODUCTION The first eight chapters of this book have primarily addressed the concepts and fundamentals associated with project valuation, particularly as they apply to mining-related projects. Specific emphasis was placed on the engineering and economic parameters and estimates necessary for quantifying line items in pro forma income statements and the subsequent calculation of net annual cash flows. Given these estimates of relative benefits, costs, and annual cash flows for a project, it then becomes necessary to convert these estimates into measures of relative desirability or attractiveness. The criteria and techniques typically utilized to determine project acceptability or desirability are, then, the topics of discussion in this chapter. Before proceeding it may be advantageous to put the problem of project evaluation into proper perspective by reiterating some of the fundamental concepts developed in Chapter 1. The basic premise set forth in this book is that the objective of the firm should be to maximize its value to its owners (stockholders' wealth). This value or wealth is represented by the market price of the firm's common stock; consequently, the primary objective of the firm can be restated as one of maximizing the value (price) of the firm's common stock in the marketplace over the long term. This price, in effect, is an indicator or index of the market's perception of the company's progress and a reflection of the investment, financing, and dividend decisions made by corporate management. These three major decisions are inter- related and jointly impact the market price of the firm's stock. Therefore, if the objective of maximizing the value of the firm to its stockholders is to be achieved, an optimal combination of the three decisions will be necessary. It is important to emphasize that maximizing stockholder wealth is not the same as profit maximization or even the maximization of earnings per share. Corporate managers making decisions based on the objectives of maximizing profits and/or earnings per share must recognize that these objectives do not consider: (I) the timing or duration of expected returns, (2) the business and financial risks of the promised earnings, or (3) the dividend policy of the firm. Obviously all of these factors are of concern to the company's stockholders and will have an effect on the market value or price of the firm's common stock. Maximizing market price per share, or wealth maximization, is therefore the appropriate corporate objective and

Jan 1, 1984

By Edward Steidle

It has been said that "the command of nature has been put into the hands of man before he knows how to command himself," and what we see about us gives particular emphasis to this observation. If this condition be granted, the vaunted boast of school and college, of the institution that had the training of this generation, and of its fathers, and of its grandfathers, the boast that education is a "preparation for life," stands exposed as a hollow claim, or as a ghastly, cynical conception of life, or else education has fallen far short of its intentions. It has been evident for some time that education was not meeting the fullest expectations of society. In recent years there has been a deal of speculation indulged in by both laity and faculty in regard to American education and American civilization, and some few and sporadic changes have been effected. Today, however, there is no longer time for mere hypothetical considerations; we are faced with certain definite facts and confronted with obvious conditions that will not wait for fine-spun theories. If educators do not put their house in order, someone else will do it for them. The trends in mineral industries education must be in harmony with this general realignment that is today visible on the educational horizon, and only as these trends are in conformity with this movement can they be called sound. Two questions, then, confront mineral industries educators: (1) What are the trends in mineral industries education, and (2) how do these trends correlate with the major educational movements of the day? Scope or Mineral Industries Education Before launching into these particulars, it might be well to define the scope of mineral industries education and to consider its present position. Mineral industries education embraces three main types of work: 1. Earth Sciences and Geography.—Geology, mineralogy, geography— courses basic to all mineral industries and to the humanities. 2. Mineral Engineering.—Mining, petroleum and natural gas—dealing with mineral producing industries. Application of earth sciences and all types of engineering to exploitation of natural mineral resources.

Jan 1, 1934

By E. S. Wheeler

THE rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the latter weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. FIG. 1.-A GROUP OF MONEL METAL AND NICKEL CASTINGS. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant. equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success.

Jan 1, 1930