Search Documents

By A. D. Smigelskas, E. O. Karenna

This is the third paper in a series on the diffusion of zinc in alpha brass.' At the time of the first paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; how ever, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. Procedure A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about 3/4 in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 0.0002 in. (1.062j + 0.0005 cm.) thick. Six0.00j-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in coppcr and alpha brass, were strctched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every 1/2 in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1947

By E. O. Karenna, A. D. Smigelskas

This is the third paper in a series on the diffusion of zinc in alpha brass.' At the time of the first paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; how ever, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. Procedure A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about 3/4 in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 0.0002 in. (1.062j + 0.0005 cm.) thick. Six0.00j-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in coppcr and alpha brass, were strctched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every 1/2 in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1947

By Charles H. Behre

SLATE (Thonschiefer, German; ardoise, French) is a rock, an aggregation of mineral grains, occurring in nature, which is used for roofing and other special purposes. It is finely granular and crystalline and generally derived from an originally clayey bed or series of beds. As a result of its having been put under essentially horizontal compression by geologic forces, this material now has its particles elongated and flattened so as to yield a very good rock cleavage along the flat surfaces of the minerals, a feature entirely independent of the original bedding in the rock. This is the gist of the definition adopted by the Committee on Slate of the American Society for Testing Materials. Slate differs in varying degrees from most other common rocks (such as limestone, sandstone, granite, and "trap") in chemical and mineral composition. Its most characteristic feature, however, is its tendency to fracture along a series of very nearly parallel and very closely spaced smooth planes, called cleavage planes. This property of cleaving, above all else, gives slate its industrial value. ORIGIN AND MODE OF OCCURRENCE Most of the features of slate might be anticipated from its origin. Being a rock rather than a mineral, its composition may vary consider- ably without impairment of value. In most slates, the material of which the rock is now composed was once deposited as clay on the bottom of a lake or sea. Subsequently these clayey strata were compressed by the kind of lateral pressure that folds rock strata, the minerals of the clay being changed or metamorphosed. In the chemical reaction involved, new and essentially plane-shaped minerals belonging to the mica groups were developed. Other minerals were formed but micas generally pre- dominated. These were oriented so that their two longer dimensions are approximately at right angles to the last effective direction of pressure. Since the crystals are thus subparallel, fractures can be developed easily along their surfaces, much as cards can be separated by inserting a knife blade between them. For the foregoing reasons, slate is found in noteworthy amounts

Jan 1, 1949

By Leah L. Naugle, H. G. Landau, H. H. Lowry

EVIDENCE has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its "Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,1-12 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends-including coals numbered I to 55b, inclusive -which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or I8-in. cylindrical retorts." In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash; from 2.1 to 15.9 per cent, in moisture from o.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the go coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1941

By H. G. Doll

A new electrical logging method. called MicroLaterology is described. whereby the resistivity R of the invaded zone close to the wall of the bore hole is measured. This method essentially utilizes a system of concentric circular electrodes iml,edded in an insulating support which is applied to the wall of the hole. A beam of current of very small diameter is focused horizontally into the formations by means of an automatic control device. and then opens widely at short distance from the wall. with this method, R most often can be recorded directly. except when the mud cake is very thick. in which case a correction is easily provided. The basic role of factor R in the quantitative analysis of electrical logs in terms of fluid saturation and of porosity is explained. The paper is illustrated with field examples. INTRODUCTION In electrical logging. the resistivity of that part of the penneable and porous formations which is invaded by mud filtrate is an important factor in the interpretation. Measurements made with the conventional devices — normal. lateral — and also with improved systems as the Laterolog and induction logging' — are very often more or less affected by the presence of the invaded zone. and the knowledge of the resistivity of this zone is useful in the evaluation of the true resistivity of the beds. which itself is a basic element for the determination of fluid saturation. Moreover. the comparison of the resistivity of the invaded zone with the resistivity of the mud filtrate gives valuable indications on the magnitude of the formation resistivity factor — which in turn is necessary for the quantitative interpretation of the logs. both in terms of fluid saturation and of porosity. On the other hand. it is generally admitted that the invaded zone is not a homogeneous medium separated from the uncon-tamirlated part of the bed hy a well defined cylindrical boundary. but that the fluid distribution—filtrate. connate water. hydrocarbon — and hence. the resistivity. in the invaded zone varies progressively with the distance from the wall of the hole. The term "resistivity of the invaded zone" therefore corre-sponds to an average value which is a function of the distribution of the fluids Inasmuch as the law of this distribution is not exactly known, the resistivity of the invaded zone is not a well defined factor. A much better definition is obtained if the medium under consideration is limited to that part of the formation which is within a short distance from the wall of the hole. It seems likely a within a distance of at least two or three in., most of the fluids in in the pores of tile formation have been displaced by the mud filtrate. The connate water has almost certainly been flushed out. and the oil. if any has generally been reduced to a comparatively small amount. The resistivity witliir~ the radial limit of two to three in. is. therefore. prac.tically constant at an). given level: its value. at least when the proportion of conductive solids in the formation is negligible. is chiefly dependent on the resistivity of the filtrate and on the porosity of the formation, and is affected only to a relatively small degree by the presence of the small amount of residual oil. This part of the formation close to the wall of the hole will he designated in the following as the "flushed zone." a-distinguished from the more general term of "invaded zone'. which relates to the part of the formation extending from the wall out to the distance where the formation is completely uncontaminated. The symbol R,, will he used for the resistivity of the flushed zone. (The notation R is related to the radial distance from the hole. If x designates this distance. xo is the initial value of x, i.e., the value corresponding to the region very close to the wall.) The determination of R is difficult, if not impossible. from logs made with the conventional devices. The long normal and the long lateral are. of course. not suited for this purpose because their radii of investigation are by far too large. The short normal. and the limestone sonde—-after correction for the effect of the hole hole — give resistivity values which corre. spond to materials situated within a comparatively short distance from the hole, but this distance is still several time. as great as the thickness of tire flushed zone. The only value which can be obtained with these devices corresponds to an average resistivity of the invaded zone- — and this only provided the invasion is deep enough, since otherwise the meas "red values would also be affected by the uncontaminated region beyond the invaded zone. It should nevertheless be recalled that despite these limitations. the measurements given by the short normal and or the limestone sonde are always very useful for qualitative interpretation. and also in favorable cases for the qantitative analysis of the logs in terms of saturation and porosity. The MicroLog. which was primarily developed for the detection of permeable beds and for an accurate determination of their boundaries. provides a good approach towards the evaluation of R. In the case of hard formation.. however. The

Jan 1, 1953

By G. O. Hiers

IN 1948 in the United States, 184,300 tons of lead was fabricated as coverings for electric power and communication cables. Such covering generally is called "sheathing" for the principal lengths of the cables, while the short lead encasements of the joints are called "sleeves." For the purpose of this paper, both lead sheathing and lead sleeving can fittingly be called lead tubing. In the United States in the same year, 34,262 tons of lead was consumed in making extruded lead pipes. Such pipe is employed frequently for water or chemical solution conveyance with gage pressures up to 100 psi. Consequently, the walls are thicker in ratio to diameter than is the case with the cable sheaths. For this discussion, lead pipes can be thought of as tubes or tubing. About 19 centuries ago, the Romans produced metallic lead of about 99.9 pct purity. Evidently this was cast in flat sheets of Y8-in. thickness, for instance. Such sheet of 10-ft lengths was bent around a removable core producing a tube somewhat oval in cross-section and with a typical internal diameter of, say, 3 in. This method of production necessitated a seam or longitudinal joint evidently made by casting the seam metal adherently. The seam metal, as analyzed recently, contains about 1 ½ pct Sn. Blow pipes were said to have been employed when the joint was made. Specimens of such pipe were found both in Italy and in the British Isles. It is believed the pipes conveyed water for drinking purposes and for baths. Numerous specimens are still in existence in a good state of preservation, due to lead's usual inertness in air or water. According to Claude E. Pearson,1 there were various stages in the evolution of lead extrusion presses for making tubes: I. First press by Joseph Bramah, 1797. 2-First successful press by Thomas Burr, 1820. 3-First bridge die press, J. and C. Hanson, 1837. In 1845, Wheatston and Crooke made the first lead sheathed electric cable. Flat lead strip was wound spirally around the insulated conductor. Overlapping edges of lead were soldered. Early cables were also made by pulling insulated conductors into 50-ft lengths of lead tube. Borel in France, and Wesselau are credited with devising the first presses for extruding lead sheaths directly on cables in 1879. In the United States, Eaton, in 188o, and Roberston, in 1885, introduced new presses of improved design. Following Cunningham's original idea of making lead traps and. bends in 1873, the presses apparently were improved and made successfully soon thereafter. Between the years 1930 and 1940, two continuous extrusion presses for lead were developed abroad. One apparently was originated by Dunsheath and made by the Henley Telegraph Works Co. The other was developed by the Pirelli-General Cable Co. CURRENT PRODUCTION In addition to the several descriptive chapters on lead extrusion in Pearson's book, the Metals Handbook2 recently described pipe, sheath, and collapsible tube production. The latter is by impact extrusion.

Jan 1, 1951

By Helmer Hedstrom

GRAVITY surveying with the torsion balance or the pendulum for ore prospecting purposes has generally not been considered practical or even possible. It is the intention of this paper to show that a fast and sensi-tive gravimeter can be very useful in ore prospecting, as an auxiliary to the electrical and magnetic instruments. A number of gravimeters have been constructed and put in practical use in the last seven or eight years; for instance, by Ising, Lejay-Holweck, Haalck, Hartley, Thyssen, Noergaard, the Humble Oil and Refining Co. and the Gulf Production Co. Their main application, apart from their use for geodetic surveys, has been for structure mapping in oil prospecting. There is no record that any of them have been used for ore prospecting. About the middle of 1934 the Boliden Mining Co., in Sweden, began experiments in constructing a static gravity meter sensitive enough for ore prospecting. Calculations and considerations that will be discussed later in this paper showed that this would necessitate an accuracy in the measurements of 0.1 milligal-roughly, one ten-millionth part of the total force of gravity. The first successful practical field tests of the instrument were made in January 1936. About the middle of 1937 the Boliden gravimeter was perfected. Ore prospecting with this instru-ment is now regular practice in Sweden, especially for the testing of indications given by geoelectric and magnetic methods.

Jan 1, 1938

By J. E. Spruiell, F. H. Patterson, B. F. Shuler

The microstructures and textures developed by the working of high-purzly thermochemically deposited tungstem sheet have been inuesligated. Greater than 60 pct reduction was required to deslroy the columnar grain structure which existed in the as-deposited sheet. With increasing reductions the texture gradu-ally charged from the initial as-deposited orientation with (100) parallel to the sheet normal to a (100}(011) ideal ovienlation with some spread about the rolling direction. This texture was retained after recrystalli-zation a1 2000°C. THE processes for depositing tungsten by hydrogen reduction of tungsten hexafluoride have been under development for the past several years.1,2 The nature of the deposition process is such that the as-deposited material contains a highly oriented columnar grain structure perpendicular to the deposition substrate. This well-defined columnar structure may be useful in certain applications293 but a wrought or equiaxed structure may be desired for some components such as tubing. Knowledge of the effects of working ther-mochemically deposited (TCD) tungsten is therefore necessary in order to establish the feasibility of obtaining worked and recrystallized microstructures and textures. The details of a recently developed technique for thermochemically depositing flat, uniformly thick tungsten sheet are presented with emphasis on the effects of deformation by rolling on the microstructure and texture. Although no work has been previously reported on the rolling and the annealing textures of TCD tungsten, there have been some determinations of textures for cold-rolled tungsten foil prepared from powder-metal -lurgy billets.4-8 The general description is that of a predominantly lurgy{100}(011) texture, with some spread about the rolling direction as an axis. pugh5 reports data both for cold-rolled and for annealed foil having about 96 pct initial cold work. He observed no change in texture, except for a decrease in the spread, for annealing treatments of 30 min at temperatures up to 1800°C. On annealing at 1900°C, both the low-temperature components plus new components which were described alternately as {001}(320) plus {001)(230) or as {100}(011) ± 12 deg about the sheet normal were observed. Above 1900°C, the new orientation existed alone, and it was stable up to 2500°C, the highest temperature that Pugh investigated. THERMOCHEMICAL DEPOSITION OF TUNGSTEN SHEET High-purity tungsten sheet was reproducibly deposited on the inner walls of a molybdenum mandrel by the thermochemical reaction WFs(g) + 3H2(g) - W(s) + 6HF(g). The mandrel was heated by a five-zone tube furnace which afforded a controllable fixed-temperature profile. Sheets measuring 1+ by 12 in. have been deposited with uniform thicknesses of up to 0.145 m. As shown schematically in Fig. 1, the purified reaction gases were metered into a mixing chamber at a Hz-to-WF6 ratio of 15 and preheated to 350°C. The flow rate of the WF6 was 300 cu cm per min at stp. These gases were directed through a conical injector into the deposition chamber. Inside this chamber hydrogen reduction of the WF6 to pure tungsten metal occurred on the hot walls of the molybdenum mandrel at a total pressure of 5 Torr. Typical temperatures for the five zones in the chamber were, respectively, 565", 540", 550°, 570°, and 590°C. The hydrogen fluorlde generated from the reaction, the excess hydrogen, and some un-reacted WF6 were pumped on through the scavenger

Jan 1, 1968

By A. D. Smigelskas, E. O. Kirkendall

THIS is the third paper in a series on the diffusion of zinc in alpha brass.1 At the time of the first-paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; however, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. PROCEDURE A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about ¾ in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 ± .0002 in. (1.0625 ± 0.0005 cm.) thick. Six 0.005-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in copper and alpha brass, were stretched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every ½ in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1946

By C. S. Allen

WITH increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration? Deceleration or retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. TYPES OF BRAKING Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the screw-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application-which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse direction. This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck" them (which reverses the connections to the motors) and then to apply

Jan 1, 1941

By M. E. V. Plummer, F. E. Beamish, J. C. Hole, J. M. Kavanagh

Prior researches have shown that the iron-copper-nickel content of platinum concentrates may be reduced by carbon to form a collecting alloy for the platinum metals in a manner exactly analogous to the formation of the lead fire assay button. The nature of the iron-copper-nickel alloys with the platinum metals has been investigated. Palladium and probably some of the other platinum metals form solid solutions with this alloy. ONE of the greatest known reserves of the platinum metals is to be found in the nickel, copper, iron sulphide deposits of Northern Ontario. The very large tonnage of copper-nickel ore processed makes the Sudbury district a significant world source of the platinum metals, the latter being recovered as byproducts in the electrolytic refining process for copper and nickel. Chalcopyrite, pentlandite, and pyrrhotite are carriers of the platinum metals;' these minerals contain from 0.03 to 2.0 ppm of the noble metals. The analysis of the above ores for the platinum metals necessitates an initial concentration of the minute quantities present in the ore. The method usually employed involves the extraction of the noble metals by molten lead with or without small proportions of silver. The lead is then separated from the precious metals by cupellation, a process which involves absorption by the cupel and volatilization of lead oxide, leaving the precious metals collected in a silver bead on the surface of the cupel. The collection by lead is probably achieved by a process of dissolution followed by some degree of segregation in the lead alloy since the cold button is seldom uniform in composition. With silver-lead alloys this process of liquation has been used to re- cover pure lead since, during the cooling period, crystals of pure lead separate and silver becomes concentrated toward the center of the solid.' Platinum and gold liquate in a manner similar to silver which may account for the successful recovery of platinum by fire assay even though it is considered insoluble in a solid lead medium. 3 In the case of iridium the liquation process may be a disadvantage in that the iridium may appear in the outer areas of the button and thus be lost mechanically during the handling processes. In any case the deficient alloying characteristics of lead for the platinum metals encouraged attempts to find an improved collecting alloy, and by analogy with aqueous extractions, preferably one in which solid solutions would be readily formed. Since, beyond a certain minimum solute to solvent ratio, the formation of a solid solution is accompanied by a lattice distortion, one would expect some relationship between the atomic diameters of any two metals and their tendency to form a solid solution. In one survey5 the hypothesis was put forward that when the atomic diameter of the solute differs by more than about 15 pct from the solvent, the "size factor" is unfavorable and the formation of a solid solution is restricted. On the other hand, when the atomic diameters are within this limit the size factor is favorable and solid solutions are readily formed, e.g. the transition metals of Group VIII having similar radii form solid solutions over wide ranges of composition.6 Even with a favorable size factor, elements having different crystal structures cannot form a continuous series of solid solutions. Cell dimensions alter as the concentration of the solute increases, causing a

Jan 1, 1962

By Werner Langguth

The modern process and plant for the precipitation of gold from chlorine solutions, by sulphurous acid gas and hydrogen sulphide, differ materially from the older methods of precipitating with sulphate of iron. The chemical process and its applicability, as carried out in the Golden Reward chlorination-works at Deadwood, S. D., was described and discussed in the Engineering and Mining Journal, of New York, for February 14, and March 21, 1891. I purpose to give, in this paper, the details of construction from a general standpoint—the particular arrangement, most suitable to each case, depending, of course, upon local conditions. The accompanying sketch shows the arrangement. The plant consists of a wooden, lead-lined tank, in which the chlorine solution is precipitated; apparatus for the production of the precipitants, sulphurous acid and hydrogen sulphide; and a pressure-tank and filter-press for the collection and filtration of the precipitated gold-sulphides. These parts and arrangements are, in general, those which I employed in the Deadwood chlorinationworks, and which have proved practically successful, more than $100,000 worth of gold having been already precipitated by this method. In the construction of the generator and pressure-tank I have made, however, a few slight changes. 1. The Precipitating-Tank. The exact dimensions of this tank are not of much importance. A horizontal area of 10 x 12 feet and a height of 12 feet, holding about 7000 gallons of solution, is a good size. As the amount of attention and care required to precipitate the solution in a precipitatingtank is independent of the size of the vessel, there is economy in tanks of large capacity. Square tanks are more advantageous than round ones, because they need less floor-space, and at the same time are cheaper in construction. These tanks are made of common 2inch pine boards and 12 x 12-inch timber. They are well-bolted,

Jan 1, 1893

By DeVerle P. Harris

Risk for most mineral investments is greater than that of average business ventures, because the physical and economic characteristics of the mineral deposit are never known with certainty. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with the adoption of the project, methods of risk analysis are important in project evaluation and investment selection. The conceptual framework for risk analysis and the means by which some of the recommended practices might be implemented are examined. In addition to the normal business risk due to market forces, the physical and economic characteristics of the mineral deposit are never known with certainty, for only partial or indirect information is available, such as data from drill cores or surface and underground workings. Consequently, risk for most mineral investments is greater than that of average business ventures. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with adoption of the project, methods of risk analysis are important in project evaluation and investment selection. This paper examines the conceptual framework for risk analysis and means by which might be implemented some of the recommended procedures. Utility Theory A discourse on risk and its impact upon investment selection quite often leads the reader into the concept of utility theory, for utility theory is a device constructed by economists to measure the satisfaction an individuai receives from a good; in the case of investment analysis, that good is the outcome of an investment. It briefly is reviewed here to describe the reaction of the individual to risk and as a stepping stone to other techniques more suited to risk analysis at the level of the firm. Utility theory proposes that an investor possess a utility map (curve), such as indicated in Fig. 1, which indicates the value in utiles of potential monetary rewards to an individual with some specific endowment of resources. Points on this map are obtained from the following relationship:

Jan 1, 1971

By G. W. P. Rengstorff

In an effort to find an oxidation-resistant alloy of molybdenum, binary and ternary alloys containing aluminum, chromium, cobalt, iron, nickel, silicon, titanium, tungsten, vanadium, and zirconium were screened. Fourteen other alloying additions were also tested. Many of the alloys were more oxidation-resistant than molybdenum, but none were entirely satisfactory. MOLYBDENUM oxidizes extremely rapidly above 1450°F in air. At 1800°F, a loss of metal at the rate of 0.1 in. in 4 hr is typical. The high speed of this oxidation may be judged by comparison with the oxidation rate of 0.1 in. per year (0.00005 in. in 4 hr), sometimes taken as the maximum permissible oxidation rate at 1800°F for a satisfactory Fe-Cr-Ni alloy. Great strides have been made in the development of coatings and cladding to protect molybdenum from oxidizing atmospheres. These developments in surface protection will undoubtedly make it possible to take advantage of the excellent hot strength of molybdellum and its alloys in many new applications. Still, even the best coating can protect molybdenum only as long as the surface layer is unbroken. Research was undertaken to determine whether an alloy of molybdenum could be found which would resist oxidation. Such an alloy would not deteriorate suddenly when the protective surface layer was destroyed in a small area. In seeking an alloy of molybdenum to resist oxidation, the physical properties of molybdenum could not be sacrificed entirely. The development of an alloy with the desired resistance to oxidation was not achieved. The information obtained on the effect of a large number of elements on the oxidation of molybdenum is, however, of value in the development of coatings. Indeed, many of the alloys tested for oxidation resistance were already known to have poor mechanical properties but were tested to aid in the development of coatings. Oxidation of Molybdenum The rapid oxidation of molybdenum is usually attributed to the volatility of Moo,,. Gulbransen and Wysong have shown that molybdenum oxidizes very slowly up to 850°F, the temperature at which the oxide film begins to evaporate. Melting as well as evaporation of molybdenum oxides promotes the oxidation of molybdenum. MoO melts at 1465°F. MOO, the oxide which is believed to form at the metal-oxide interface, combines with MoO, to form a eutectic having a melting point of 1432°F.' The liquid oxide, even if nonvolatile, could cause poor resistance to oxidation by allowing easy transport of molybdenum and oxygen ions through the oxide. Actually, a sudden increase in the rate of oxidation of molybdenum at 1460°F has been observed to coincide with the appearance of a liquid phase. The formation of a volatile oxide is not unique with molybdenum. The problem is also encountered with vanadium, tungsten, and some of the Pt-Pd group of metals. Vanadium not only forms the volatile V2O3 but, like molybdenum, forms a liquid oxide coating. Few attempts have been made, however, to prevent the rapid oxidation of these metals by alloying. Oxidation of Molybdenum Alloys At the beginning of this work, very little was known of the oxidation resistance of molybdenum alloys. It was known that molybdenum disilicide (with 37 pct Si) has extremely good oxidation resistance,' but this compound is so brittle that it has few uses. It is an effective protective coating for molybdenum when allowance can be made for its brittleness. Chromium was known to retard the oxidation of molybdenum,' but at least 50 pct Cr was necessary to have an appreciable effect. Other, unpublished, reports show that a few other alloys have been given preliminary tests, but the results have not been promising." Choice of Alloys to be Investigated An alloying element might be expected to protect molybdenum in either of two ways: Its oxide might combine with molybdenum oxide to form a stable, nonvolatile complex oxide (a molybdate); or the oxide of the alloying element might form in preference to molybdenum oxide, developing an impervious layer which would prevent the formation of a volatile molybdenum oxide. The knowledge available about the formation of molybdates was meager. Therefore, the initial study was made on alloys of molybdenum with elements having especially stable oxides. On this basis, binary and ternary alloys containing the following six elements were investigated: aluminum, chromium, titanium, zirconium, silicon, and vanadium. Nickel was also added as an alloying element. Although it does not form a more stable oxide than molybdenum, it does impart some oxidation resistance to copper and iron. Its inclusion in the study was fortunate because its alloys proved to be the most promising of those first tested. Apparently nickel formed a stable molybdate. Because nickel was effective in reducing the oxidation rate of molybdenum, the elements iron, cobalt, and tungsten were added to the list. The ten alloying elements mentioned form ten binary and 45 ternary alloying systems with molybdenum. A series of alloys was tested in each of these systems. In addition, at least one test was made on the effect of each of the following alloying elements:

Jan 1, 1957

By K. E. Gray, A. Podio

ABSTRACT Berea and Bandera sandstone samples were impacted with both 3/4-in. and 1/2-in. long wedges, each having a 60° included angle and a 0.05-in. flat, at various confining pressures, with borehole and pore pressures held fixed at atmospheric pressure. Samples were saturated with air, water, glycerine-water, solirol, mineral oil and soltrol-mineral oil mixtures to obtain a wide range of pore fluid viscosity. Penetration depth was held constant at 0.1 in. Dry and soltrol-mineral oil-saturated Berea samples were impacted at depths of penetration from 0.01 to 0.04 in. under 1,000 psi confining pressure to study crater initiation. Results indicate that viscosity of the pore fluid is influential primarily during the early stages of crater formation. Differences in bit force, crater volume and blow energy for tests parallel and perpendicular to bedding were significant, but decreased as the stress state was elevated. Crater volume, blow energy and bit force were nonlinearly related with depth of penetration. Crater volume was nonlinear with energy of blow. Fixed-penetration tests on saturated Berea yielded greater crater volume than did similar tests on dry samples. Differences in the nature of deformation for low values of bit penetration were noted between saturated and unsaturated samples. INTRODUCTION Rock failure during bit-tooth impact and scouring action constitutes a vital part of the drilling process and a difficult problem for researchers. Much study has been devoted to various aspects of the problem, and much has been learned about mechanics of rock failure. However, analytical treatment of drilling at depth remains difficult, partly because there are so many factors involved and because valid simulation of downhole conditions is extremely difficult. Forming individual craters by a bit tooth or chisel impacting, or indenting, a rock mass has been studied by many investigators.1-18 Similarity between single-tooth chisel impact and the corresponding action of a rotary bit has been discussed by Appl and Gatley, Garner, Podio, and Gatlin l8 compared the similarity in single-blow impact tests with microbit drilling data reported by Cunningham and Eenink.l9 Maurerll has used single-tooth impact data to develop a "perfect cleaning" theory of rotary drilling. Individual roller cutter-tooth impact data have been reported by Young. 20 Single-tooth tests in all of the cited literature were carried out on dry rocks. Inasmuch as any subsurface rock of oilfield interest is saturated with some fluid, it seemed desirable to study crater formation in permeable rocks saturated with a viscous pore fluid as a step, however short, toward more realistic simulation of subsurface conditions. This paper presents results of single-blow chisel impact studies on Berea and Bandera sandstones, both dry and saturated with pore fluids of various viscosities at confining pressures to 10,000 psi. EXPERIMENTAL APPARATUS AND PROCEDURE EXPERIMENTAL APPARATUS The same basic apparatus for single-blow chisel impact at elevated stress states, described in earlier papers was used in this study. l6. l8 Fig. 1 shows the complete experimental system; Fig. 2 shows a cross section of the pressure cell, with a sample ready to be impacted. EXPERIMENTAL PROCEDURE Two different rocks, Berea and Bandera sandstones, were used in this study. Both rocks have been used extensively in research, and rock descriptions can be found in a paper by Gnirk and Cheatham.15 Permeability to air of Berea is about 300 md normal to bedding and 540 md parallel to bedding. Bandera had vertical and horizontal air permeabilities of 18 and 57 md, respectively.

Jan 1, 1966

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.' According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By Hans Strack

Electroluminescence of GaAs p-n junctions fabricated by simultaneous diffusion of sulfur and iron was investigated at 77°K. A narrow emission peak with a half width of about 4 kT in the energy range between 1.14 and 1.155 eu was attributed to iron. Other transition elements exhibited light emission in the vicinity of the iron peak, namely nickel between 1.15 and 1.16 ev and cobalt between 1.16 and 1.17 ev. The efficiency of the doping with iron depended on the amoz~nt of arsenic present. A weight ratio of arsenic to iron of 4:l was sufficient to observe the emission lines associated with transition elements. The presence of oxygen reduces the intensity of the light emission. In addition to the levels associated with transition elements, levels at 1.05 and 1.28 ev, probably due to lattice defects, are observed except in diodes fabricated in solution-grown GaAs. THE near band edge emission of GaAsp-n junctions has been studied extensively in the past.' GaAs devices utilizing spontaneous and stimulated near band edge emission are of considerable practical importance. Typical junctions are fabricated by diffusion of a heavily doped p region into degenerate n-type GaAs. Much less work has been done on investigating the radiative recombination via deep levels in lightly doped p-type material. This area is of interest in understanding the performance of GaAs n-p-n transistors. GaAs transistors show remarkable improvement in high-frequency performance and current-gain stability at high temperatures, when iron is added to sulfur during the emitter diffusion process. The present work was initiated to investigate deep-level electroluminescence of iron-doped GaAs p-n junctions fabricated on vapor-phase epitaxial GaAs and on solution-grown GaAs. For comparison several diodes doped with cobalt and nickel were studied. Iron, cobalt, and nickel have an electron configuration of the type

Jan 1, 1968

By H. H. Kellogg

Available high-fernperatzwe equilibrium measurements and other thermochernical data have been critically reciewed for sulfation reactions of the type: Recommended values for log K and ?Fo as junctions of temperature are given for thirty-six suck reactions involving twenty-six different metals. Methods of calculation and choice between conflict-ing data are discussed. SELECTIVE sulfation now enjoys a considerable renaissance as a metallurgical unit process due, in large part, to the available of the fluid-bed re- actor—a device capable of the close control of temperature and gas composition necessary for a successful sulfation process. An additional need, however, if sulfation chemistry is to be approached in a scientific manner, is a reliable body of data on the equilibrium and kinetics of sulfation reactions in simple and complex systems. This paper offers a critical review and compilation of equilibrium data on pure sulfates (simple systems). The last such review, by K. K. Kelley in 1935:30 has proven itself most useful, but the existence of many new data makes necessary a re-evaluation of the available information. METHODS OF CALCULATION For a simple sulfation reaction such as MS04(c) = MO(c) + SO3 [1] there are two approaches one may take toward establishing the value of ?Fo or K as a function of

Jan 1, 1964

By Arnulf Muan, Klaus Schwerdtfeger, L. S. Darken

The equilibrium ratios CO/CO, of. a gas pharse coexislitrg with selected oxide phase assemblages of the system "FeO"-MnO-SiO2 and metallic iron have been determined at 1150°C. The data obtained are combined wilh the thermodynamic data on fayalite (Fe2SiOi) and "FeO"-MnO solid solutions to derive the actiuity-coiHpQsiUon relations for the various oxide components of the olivine (Fe2SiO4-,lIn2Si04) and pyroxenoid (standard free energies of formation of ferrosilile (FeSiO,), tephroite , and rhodonite from their oxides have been evaluated. In the Appendicc~s by Darken and Schivcerdtjeger the ideal solution law for solid deri oed. THE quaternary system Fe-Mn-Si-0 is of interest in many important phases of iron- and steelmaking. For instance, reduction in the blast furnace of ores containing Fe-Mn silicates, deoxidation of liquid steel with Mn-Si alloys, formation and subsequent alterations of oxide inclusions in steels, and the oxidation of manganese- and silicon-containing steels during processing are all governed largely by the thermodynamic relations existing in the system Fe-Mn-Si-O. Although the equilibria between liquid iron and Fe-Mn silicates have been studied in detail previously,' experimental data are lacking for equilibria among the solid phases. The present paper provides such data for a selected temperature, 1150°C. I) PREVIOUS WORK The general feature of subsolidus phase relations in the system iron oxide-manganese oxide-silica under strongly reducing conditions is known.' Fig. 1 represents an isothermal section at 1150°C. The phases present, in addition to silica, are three solid-solution series, viz.. the oxide solid-solution series "Fe0"-MnO (manganowiistite), the orthosilicate solid-solution series Fe2SiO4-Mn2SiO4 (olivine), and the metasilicate solid-solution series FeSi03-MnSi03 (pyroxenoid). The "FeO"-MnO solid solution is continuous between the two end members wustite and manganositeV3 as is the orthosilicate series between the two end members Fe2SiO4 and Mn2 SiO4. 4 The metasilicate solid solution, on the other hand, extends only part way from the MnSi0.l end member toward FeSiO because the latter end member is unstable relative to the phase assemblage fayalite + silica. The letters a through m in Fig. 1 identify end members of the individual solid phases dealt with [for instance, c designates fayalite (FeZSiO4) in equilibrium with wustite, e designates fayalite in equilibrium with silica, and so forth]. In addition to the phase relations there are some thermodynamic data available for the end members of the silicate solid solutions and for the "FeO" -MnO solid solution. The free energy of formation of fayalite (Fe2Si04) from its oxide components has been studied by several investigators. Unfortunately, the data obtained show considerable discrepancies. According to recent tabulations by Kelley, the change in standard free energy Affn for the reaction

Jan 1, 1967

By D. W. Fuerstenau

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed, and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped down, a period of 1 hr or so is required. When a disturbance in the feed rate was made, the transient period extended to more than 1% hr (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content

Jan 1, 1983