Search Documents

By Donald W. Petrasek

The effects of selected alloying elements on the elevated-temperature tensile properties of copper alloy -tungsten fiber reinforced composites were invcstigated. A cornparison of the elevated-temperature tensile properties of copper alloy - tungsten fiber reinforced composites, representing soluble systems. was made with copper - tungsten fiber reinforced composites, representing a mutually insoluble system. A linear relation between tensile strength and volume percent fiber content existed at elevated temperatures for all the systenzs investigated. The copper alloy composites were weaker in tension at high volume percent fiber contents than copper composites in which alloying with the fiber did not occur. The tensile strength of the alloyed tungsten fiber decreased with increasing penetration of the alloying element into Ihe tungsten fiber. THE technique of combining strong fibers with relatively weak matrix materials so that the fibers are load-carrying members has been utilized for many years in the reinforcement of plastics with glass fibers. This type of strengthening is currently being extended to include the reinforcement of metals with metallic fibers. Investigations of the room-temperature tensile properties of metal-fiber-reinforced metallic composites have been numerous,'-" but the study of tensile properties at elevated temperatures has been limited. In previous work done at the Lewis Research Center' composites consisting of mutually insoluble constituents were investigated. Composites were made of copper reinforced with uniaxially oriented tungsten fibers. The stress-strain behavior and tensile properties of the composites were related to the tensile properties of the base materials. The tensile strength of the composite was directly proportional to the volume percent of tungsten fiber present, and the full strength of the fiber was realized. Few metal fiber - metal matrix systems exist that are mutually insoluble, and those that do exist are not generally practical. An extension of this work was an

Jan 1, 1967

By A. Kavetsky, W. J. Whiten

Data from ball mills with a wide range of diameters are analyzed using detailed mathematical/ numerical models. Analysis shows the relative power inefficiency of large ball mills is due to their inefficient breakage of coarse particles. The models developed can be used to scale-up mill behavior. The behavior of large mills at Bougainville and Pinto Valley is compared. It is concluded that the mills are equally inefficient at grinding coarse particles. Differences in coarseness of total mill feed are shown to account for the fact that Pinto Valley mills achieved design throughput whereas Bougainville mills did not.

Jan 1, 1985

By Igor Plaksin

Interaction of sulfide minerals and native metals with reagents in flotation is largely determined by particle-surface changes resulting from action of the medium and dissolved gases. A number of early studies were devoted to the selective action of various gases on minerals.1 Mc- Lachlan2 paid attention to oxygen as the most active gas affecting flotation properties of sulfide minerals.

Jan 3, 1959

By Milton E. Wadsworth, Daniel B. Brimhall

Column leach studies of a low-grade porphyry copper ore were made. The technique used involved alternating oxygen absorption and copper leach cycles. The leach solution was displayed from the column with oxygen. The volume of oxygen reacting with the ore was measured with a gas burette. The copper released as a result of exposure to oxygen was correlated with the oxygen uptake. The oxidation rate was found to be dependent on the pH of the solution wetting the particles and was markedly increased by increasing the temperature of the system. Decreasing the particle size of the sample increased the oxidation rate. A material balance on the system indicated 1 mole of oxygen yielded in excess of 1 mole of copper in solution. A discussion of the important parameters is presented and the results are related to dump leaching in general.

Jan 1, 1974

By Lauren A. Wright, A. E. J. Engel

Under the designations "industrial talc" and "soapstone" are included earth materials of widely different chemical and mineral compositions. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3(SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.18 Single grains or leaves of talc, however, seem to have variations in water content that range from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.20 Most of the industrial talcs produced in the United States do not approach the composition given above (see Table 1), but are essen- [ ]

Jan 1, 1960

By R. S. Barneyback

Not much more is known about concrete today than was known to the Romans. For all the research only better tools have resulted to measure the quality of the materials that go into it." In this paper "some of the materials for lightweight concrete and their characteristics are considered and effort is made to indicate their effect on the end result — a structure of lightweight concrete." Lightweight concrete had noble beginnings. It is believed that the first specification for lightweight concrete was written by the Roman Emperor Hadrian in the early years of his reign, 117-138 AD. Hadrian, was an engineer by trade and an Emperor by adoption. He took considerable interest in the structures sponsored during his reign, even to the point of working out the structural details and preparing working drawings for some of the more prominent works in the vicinity of Rome. In order to reduce the dead weight of the 140 ft diam dome of the Pantheon he specified that the lightweight structural concrete members supporting this concrete and tile composite dome were to be fabricated from a concrete containing pumice and scoria. Still standing after 18 centuries of abuse, this structure has been described as the master effort of a great structural genius, the ultimate achievement of Roman engineering skill.' The Romans were the first to employ many concrete techniques we think of as modem innovations. Some unnamed superintendent noted that when a carefully measured amount of pigs blood was measured into each batch of concrete during mixing, the concrete was more durable and exhibited much better resistance to freezing and thawing climates. He no doubt, attributed this success to the appeasement of one of the gods who in return provided protection for the building containing this sacrificial offering in its walls. It is known today that the blood-entrained air in the concrete tends to make mixtures more workable, resistant to moisture penetration and more resistant to frost damage.

Jan 1, 1964

By G. W. Garside

In order to render my descriptions more intelligible, I have compiled a general map of this section of Alaska, showing accurately the relative positions of the most important districts where valuable deposits of minerals have been discovered (page 819). Upon inspection of this map, it will be observed that the chief metalliferous belt in this mineral field is in close proximity to the mainland shore, the trend of which it follows for more than a hundred miles in a northwest and southeast course, while the mineral croppings on the adjoining islands are much shorter in extent, and more irregular with respect to their strike and continuity. This principal metalliferous zone, which I will call the main-land system of lodes, contains gold, silver and lead, besides traces of copper, zinc and iron, gold being found extensively in a free state and also associated with sulphur, and with many of the sulphides of iron, lead and other substances. On the line of this belt, as shown on the map, there are a number of distinct mineral districts. Beginning at the southerly extremity, they are named as follows: Sumdum, Snettishham, Grindstone Creek, Sheep Creek, Gold Creek, Lemon Creek, Montana Creek and Berners Bay districts, each deriving its name from the hay or creek on which it is situated. Harris mining district, as legally organized under the local customs, rules and regulations adopted by the miners of Juneau, embraces, within its exterior boundaries, Grindstone, Sheep, Gold and Lemon Creeks, and all of Douglas Island. The limits of this immense metalliferous horizon are becoming definitely known through the exposures made by prospectors. The belt, as now recognized, varies in width from one to several miles, the lateral measurement being greatest at Juneau in Harris district, where the famous Treadwell mine, with its slate foot-wall, marks the westerly boundary of the zone, while the eastern side of Silver Bow Basin, with a granite hanging-wall, defines its easterly border.

Jan 1, 1893

By Thomas L. Wright

Exploration activities were maintained at a high level throughout 1966. Numerous significant discoveries and developments in which geologists played an important part were announced. Although the complete results of exploration activities carried out during the year by private companies have not been announced, the following are among the more important developments that have been made public knowledge. In the western states, exploration for practically all of the metals continued at a high rate. Substantially increased interest in uranium occurred this year, and it is felt by many that a real boom in the demand for uranium may come about in the near future. The reasons have been the more rapid acceptance of atomic power than had been anticipated, and that uranium producers can now sell their product to private interests and even foreign countries. A tremendous demand for uranium is anticipated by many, and this has rekindled exploration activity. On the Colorado Plateau, in Wyoming, and in the area around Grants, N. M., a number of companies have undertaken uranium exploration programs, among which are Kerr-McGee, Homestake, Anaconda and Utah Construction. A new uranium orebody in Texas was brought into production early in 1966 by Susquehanna Western.

Jan 2, 1967

By R. L. Templin

IN TREATING a cast metal by any working process such as rolling, drawing or forging, variations in the conditions present in the remelting, casting, chilling and preheating of the initial ingot will certainly have some effect on the physical properties of the final product. In considering the effects of cold working on the physical properties of metals, however, it will be assumed that these factors, being controlled according to best practice, will remain constant and therefore may be neglected. Starting with such a uniform metal ingot, the next operation in the production of wrought metal involves hot working by rolling, forging or extrusion so as to produce a slab, billet or bloom. This working must be sufficient to produce substantial grain refinement and minimize any defects occurring in the initial ingot. Even such a hot-worked product is not suitable as a starting material for determining the effects of cold working because it contains internal strains analogous to those resulting from cold working. It is necessary, therefore, to supplement the hot working with a considerable amount of cold working, followed by a proper annealing in order to obtain a material suitable for use in defining the effects of cold working on the physical properties of a metal. That is, if the effects of cold working are to be evaluated accurately it is necessary to have other effects at least constant if not absent. Such material, unfortunately, cannot always be obtained in commercial practice but the requirements just indicated certainly represent the desired goal; this goal has been attained in the treatment of some metals, one being aluminum.

Jan 1, 1929

By N. R. Adsit

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from offman:"

Jan 1, 1967

By S. F. Emmons

" The obscurity which still veils from us the true nature of veins will become more and more cleared up when they can be considered in connection with the geological structure of the regions in which they occur."* These words, according to Lossen, the biographer of the late Dr. A. von Groddeck, of Clausthal, were the last received by him from that eminent man, perhaps the most far-sighted and carefully progressive of recent writers on ore-deposits. They seem to me to form a fitting text for what I am about to say; since I find that many of the conclusions at which I have arrived by my own study of the structural relations of ore-deposits, or, in other words, of the structural and dynamic geology of the regions in which they occur in this country, have been similarly determined by him within recent years in Europe, and especially in his home field of work, the Hartz. I shall not enter upon a detailed account of how far other workers may have arrived at similar conclusions with myself, since these questions of priority are of little interest, except to those immediately concerned; but will briefly present the methods by which, in my work in this country, I have arrived at certain generalizations, and will point out the practical bearing which they may have upon the work of mining engineers. In my first thorough and systematic examination of an important group of ore-deposits, viz., that of Leadville, Colorado, I was enabled, through the generous facilities afforded me by the then Director of the Geological Survey, Mr. Clarence King, to make a most elaborate and detailed study of the geology, not only of the immediate vicinity of the mines, but of the adjacent mountain regions, based upon accurate topographical and underground maps, and

Jan 1, 1888

By C. G. Dunn, F. W. Daniels, M. J. Bolton

IN recent investigations1. a data on relative grain boundary energies in silicon iron have been obtained. The present investigation is a continuation of this work along similar lines for the purpose of obtaining additional information on boundary energies. One aim has been to extend the data for a (110) series, which was formerly studied,' to small differences in orientation, since a recent theory3,4 based on a dislocation model of grain boundaries predicts a E. ? (A-ln ? )* form of energy curve for small differences in orientation. Another aim has been to provide data for a (100) series—all grains having (100) planes parallel with the surface of sheet speci-mens—and to compare the results with the predicted form of energy curve. Finally, information on the nature of approach to equilibrium conditions was to be obtained through observations on the movements of grain boundaries. Recently published papers2,3,5 have treated the mathematical problem of expressing equilibrium conditions for grain boundaries for the general case when boundary energy depends upon boundary orientation. The equilibrium equations, which relate equilibrium angles and grain boundary -free energies, contain additional terms that express the variation of energy with boundary rotation. It has been necessary in the present investigation, however, to neglect these additional terms since no data for their evaluation were available. Dropping the additional terms leads to the following approximate equations which were used: E12/sin ?3 = E18/sin?2 =E28/sin?1 or those of the form: E28 + E13 cos ?3 + E12 cos ?2 = 0 Experimental Procedure Except for sample F1, all specimens were made from two lots of silicon iron called C and L respectively. The compositions of these are listed in table I. In the preparation of 12 three-grain specimens for the present investigation, a controlled grain growth technique, which has been described previously,' was used. After preparation, the specimens were notched at the boundaries to shorten them as a means of providing more rapid approach to equilibrium in the anneals. Initial grain boundary angles were determined from micrographs taken at X500. Seven anneals, totaling about two days at 1300°C and two to four days at 1400°C, were run in an atmosphere of pure dry argon as described in a previous paper.' Boundary changes generally could be followed without metallographic surface preparation, because thermal etching occurred during the anneals. These observations indicated angle changes of as much as 35" in some instances, with the major changes occurring during the first anneal. Annealing was discontinued when the angles reached stationary values. Fig. 1 gives a schematic diagram for purposes of defining crystallographic and boundary directions for three grains with common plane parallel with the sheet. Differences in orientations (expressed by A) are the angles between [00l] directions. They can be calculated with the aid of the ?'s. The grain boundary angles can be calculated from the w'S. Results Results are given in table 11. Types of crystal-lographic planes refer to those parallel with the sheet. Orientations are given in terms of [00l] direc-tions as shown in fig. 1. Except for grain 3 of specimen H6, which was unintentionally tilted 7" out of a (100) plane, all grains generally were within 1" or 2" of the plane specified. The directions of boundaries were measured generally to within 1" on both upper and lower surfaces, and the average direc- tions were determined for use in calculating the grain boundary angles. Variations in grain boundary directions refer to deviations from average directions. Boundaries near the junction point for all specimens generally were very close to perpendicu-

Jan 1, 1951

By P. D. Proctor, M. P. Nackowski

Quantification in recording geologic phenomena and application of well-known geologic principles to engineering works continued at an increasing rate during the year. Highway departments, water resources agencies, private firms and governmental agencies involved in tunnel excavations, dam site locations and construction, consultants and government experts in subsurface liquid-waste disposal, designers of underground storage facilities and city and regional planners all confirmed greater use of applied geology in their planning and implementation of plans. Applications of quantified geologic data to highway locations, slope control of cuts, raw material sources, water sources and water run- off showed a striking increase in number. Environmental geology and geologic hazards became part of the jargon of the geologic profession, and the American public began to realize more fully the significance of where they live, and on what and near what geologic phenomena which might effect their well-being. Tunnel work for water projects of almost dream-like magnitude kept geologic engineers busily engaged in predicting and testing local geologic conditions for construction projects. Disposal of industrial and radioactive liquid wastes continued as problems, but use of stratigraphic data, fluid flow rates and direction of flow helped solve some critical waste disposal problems. Unusual applications of seismic networks, remote sensing methods and X-ray techniques in geological engineering applications added other tools to this increasingly important profession.

Jan 2, 1968

By S. H. Gelles

Samples of poly crystalline zinc of 99.999+ pct purity were observed metallographically after having been exposed to hydrostatic pressures of up to 27 kbars. The deforrnation produced by this treatment was analyzed using X-ray and metallogaphic techniques. Basal-plane slip occurred universally in all grains exumined at the lowest pressure used (8 kbars). At pressures of >23 kbars, {1012} twin nucleation and growth were noted as well as slip. Formation of bend planes, complex kink bands, and recrystallization at the gain boundaries were also observed in this pressure range. These observations are discussed in reference to the expected deformation behavior of zinc under high hydrostatic pressure. It has been shown over the past few years1'3 that anisotropic, poly crystalline metals can be made to deform plastically by the application of a hydrostatic pressure. The effect is greater 1) the larger the anisotropy of linear compressibility and 2) the smaller the stress level needed to produce plastic deformation. Zinc having both very anisotropic linear compressibilities and a very low critical resolved shear stress (CRSS) for basal-plane slip has been shown to exhibit large amounts of plastic deformation when subjected to a hydrostatic pressure.2,3 At pressures up to 15 kbars, grain boundary migration and slip on one set of glide planes have been reported.' After exposing samples to 20 kbars pressure, grain boundary migration, single slip, multiple slip, and twinning have been noted.' The identification of the deformation modes operative under these conditions has not been reported. It was the purpose of this research to identify the deformation modes induced in poly crystal line zinc by the action of a hydrostatic stress and to study the strain accommodation at grain boundaries. Hydrostatic pressure could affect the operational modes of deformation by altering the Peierls-Nabarro stress. This may be roughly approximated by the relationship4

Jan 1, 1967

By Haydn H. Murray

Although alumina constitutes about 15% of the earth's crust, it is expensive to separate and purify for the production of aluminum with the exception of the alumina in bauxite. The United States has a variety of nonbazurite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline venite. Each of these resources is discussed from the standpoint of geology, geography, processing, and potential recovery. Potential byproducts include alica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1983

E. R. Buckley, Flat River, Mo. (communication to the Secretary*) :—Some statements in the paper of Mr. Keyes relative to the nature and formation of the Ozark lead- and zinc-deposits seen1 to me erroneous and misleading, and I respectfully present the following criticisms, placing Mr. Keyes's original statements in quotations. Referring to the Ozark dome: (p. 192.) "It is a region that has been repeatedly upraised and planed off, until in the middle portion the oldest known rocks only are exposed." Does he mean that the St. Francois mountains, which have always been considered as lying on the eastern flank of the Ozark dome, are the middle of the dome ? Or does he mean that the Cambrian rocks of the generally-accepted middle are the oldest known rocks ? Certainly not the latter, and if the former, his idea of the middle of the dome is not in accord with that of others who are familiar with the region. (p. 203.) "... the ore-deposits are definitely associated with, or localized by, geologic structures of some kind that produce in effect basins in which the underground waters are impounded, or their flow retarded." This statement does not appear to be altogether consistent with the facts, since the ore bodies of the Joplin district, as the rule, occur in those parts of the Mississippian formation which have a tendency to accel erate the flow of ground-water rather than retard it. I migh name the open, brecciated ground near Joplin, Webb City, and Oronogo as especially noteworthy illustrations. The ore-bodies, everywhere, occur in positions where there must have been a free and copious circulation of dilute lead- and zinc-solutions in the presence of reducing constituents. The inequalities in the distribution of the ore-deposits are

Jan 1, 1910

By A. I. Krynitzky, Henry S. Rawdon

The most commonly used material for terminals in spark plugs is commercial nickel wire, because of its relatively high temperature of melting, excellent heat conductivity, and slow rate at which the metal is oxidized, even upon continued heating at high temperatures. The grade commonly used for this purpose averages 97 per cent. nickel, the remainder being manganese, cobalt, iron, copper, with traces of other impurities always found in commercial nickel. A peculiar and interesting type of deterioration that occurs in these nickel terminals during the service life of the spark plug was recently brought to the attention of the Bureau of Standards. Commercial spark plugs vary greatly in their size and shape and the terminals differ considerably as to their relative size, shape, number, and arrangement with respect to one another. Although this defect was studied in detail in only one form of spark plug, the deterioration is a characteristic of the material, i.e., of nickel wire, rather than of the particular type of spark plug in which it was noted and studied. The mechanical features of the plugs, however, have a considerable bearing on the time required for the deterioration to become serious. The results of this study of the deterioration of nickel terminals in service should be of value to the makers of all types of spark plugs in which the terminals are made of this metal. CharacteR of Deterioration of WIres During Service Macroscopic Appearance and Properties of Changed Wire.—The nickel terminals in which the deterioration was studied were taken from spark plugs having a central terminal with the ground or side terminals attached firmly at both ends to the shell of the plug. In some of the plugs, two side terminals were used, one on each side of the central one. Although both terminals were found to have deteriorated to some extent, the attack of the central one was quite negligible compared to that of the side ones. These latter wires had developed, in service, transverse cracks that, in many cases, were as sharp and definite as a knife-cut. After a separation occurred, the breach widened by loss of material from the

Jan 1, 1921

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbogenerator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring. Hardening in this case was obtained by cold working, such as hammering, rolling or some means for stretching the steel while at a temperature near 500" C. One means for stretching2 is to rotate the forged or rolled ring in a centrifugal machine so as to develop within it stress higher than

Jan 1, 1931

By HUNTINGTON ADANS

(Wilkes-Barre Meeting, June, 1911.) THE arrangement of a flow of cyanide-pulp through Pachuca tanks in agitation, so as to permit a continuous process, instead of alternate filling, agitation, and emptying, has been proposed by various writers within the last two years, and more particularly by A. T. Grothe, agent for the Brown patents on Pachuca tanks in Mexico. It was first put into practice, I believe, by M. H. Kuryla at the Esperanza mine in El Oro, Mexico. The starting of agitation in Pachuca tanks after filling may offer no serious difficulties with ores which do not settle rapidly in such tall tanks; and the adaptation of the tanks to continuous agitation under such conditions may give simply a somewhat more convenient method of treatment and greater agitation-capacity for a given number of tanks, because of the saving -of time lost in filling and discharging. But in the treatment .of pulp which tends to settle rapidly, as in the cyaniding of concentrates or of the whole pulp of ores containing heavy sulphides, the packing of the slime at the bottom may, cause much trouble. The use of the radial air-pipe attachments near the top of the cone and of the air-valve outside of the air-lift .tube at the bottom may obviate the difficulty to some extent; but the action of the radial air-pipes on the cone-sides is that -of a sand-blast, and their continuous use cuts through the tanks. Moreover, even when these pipes are used, some pulps will pack tightly below them in the cones. Under such conditions the use of Pachuca tanks with intermittent filling and discharging becomes a troublesome process. Time is lost in ,starting agitation; large quantities of compressed air are wasted; pulp is blown over the tank-tops; and not infrequently it may be necessary to dig out the bottoms of tanks by hand. This trouble is the only important one occurring in the use of Pachuca tanks; and, since it is caused by intermittent filling, the .arrangement of a continuous flow of pulp from tank to tank,

Aug 1, 1911

By Philip Davidson, Wm. B. Price

The object of this paper is to present, a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350" C. throughout the coininercial annealing range.. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: Alloy Copper, Lead. Iron. Nickel, ManGanese, Zinc, PeR Cent. Per Cent. Per Cent. Per Cent. Per Cent. PEr Cent. A................ 64.68 Trace 0.194 6.73 0.06 remainder B................ 65.82 1.27 0.227 6.17 0.06 remainder C................ 65.44 Trace 0.345 17.83 0.08 remainder D................ 65.60 1.08 0.238 17.77 0.06 remainder These alloys were lolled in accordance with regular mill practice to approximately No. 6 R. & 6. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 1/2 in. long by 1/2 in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 235 in. were also taken.

Jan 1, 1921